Deutsch dropdown-ico

Sharp R-216LS Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Sharp R-216LS an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Sharp R-216LS, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Sharp R-216LS die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Sharp R-216LS. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Sharp R-216LS sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Sharp R-216LS
- Den Namen des Produzenten und das Produktionsjahr des Geräts Sharp R-216LS
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Sharp R-216LS
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Sharp R-216LS zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Sharp R-216LS und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Sharp finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Sharp R-216LS zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Sharp R-216LS, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Sharp R-216LS widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING T O A VOID POSSIBLE EXPO- SURE TO EXCESSIVE MICROW A VE ENERGY CHAPTER 1. W A RNING TO SER VICE PERSONNEL CHAPTER 2. MICROW A VE MEASUREMENT PRO- CEDURE CHAPTER 3. FOREWORD AND W ARNING CHAPTER 4. PRODUCT D ESCRIPTION CHAPTER 5. GENERAL INFORMA TION CHAPTER 6. OPERA TION CHAPTER 7. TROUBLESHOOT[...]

  • Seite 2

    CONTENTS PRECAUTIONS TO BE OBSER VED BEFORE AND DURING SERVICING T O A VOID POSSIBLE EXPO- SURE TO EXCESSIVE MICROW A VE ENERGY CHAPTER 1. W ARNING TO SERVICE PERSONNEL [1] Before Servicing ........ ...... ............. .......... .... 1-1 [2] When the testing is co mpleted, .... ............. . 1-1 [3] After repairing ............... .............[...]

  • Seite 3

    R216LS i R216LS Service Manual PRECAUTIONS T O BE OBSERVED BEFO RE AND DURING SER VICING TO A VOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW A VE ENERGY BEFOR SER VICING PRECAUTIONS T O BE OBSERVED BEFORE AND DURING SERVICING T O AVOID POSSIBLE EXPOSURE T O EXCESSIVE MICRO W A V E ENERGY (a) Do not operate or allow the oven to be operated with the doo[...]

  • Seite 4

    R216LS 1 – 1 R216LS Service Manual CHAPTER 1. W ARNING T O SERVICE PERSONNEL Microwave ovens contain circuitry capable of producing very high voltage and cu rrent, contact with following parts may result i n a severe, possibly fatal, electrical shock. (Example) High V oltage Capacitor , High V oltage Power T ransformer , Magnetron, High V oltage [...]

  • Seite 5

    R216LS 2 – 1 R216LS Service Manual CHAPTER 2. MICROW A VE MEASUREMENT PROCEDURE [1] Requirement s: 1. Microwave leakage limit (Power density limit): The power density of microwave ra d iation emitted by a microwave oven should no t exceed 1mW/ cm 2 at any point 5cm or more from the external surface of the oven, measure d prior to acquisiti on by [...]

  • Seite 6

    R216LS 3 – 1 R216LS Service Manual CHAPTER 3. FOREWORD AND W ARNING [1] FOREWORD This Manual has been prepared to provide S harp Electronics Corp. Service Personnel with Operation and Service Info rmation for t he SHARP MICROW A VE OVEN, R-216LS. It is recommended that ser vice personnel carefully study th e entire text of this manual so tha t th[...]

  • Seite 7

    R216LS 4 – 1 R216LS Service Manual CHAPTER 4. PRODUCT DESCRIPTION [1] SPECIFICA TIONS ITEM DESCRIPTION Power Requirements 120 V olts 60 Hertz Single phase, 3 wire grounded Power Consumption 1 170W / Approx. 10 Amperes Power Output 800 W nominal of RF microwave energy (IEC T est procedur e) Operating frequency 2450 MHz Case Dimensions Width 18-1/8[...]

  • Seite 8

    R216LS 5 – 1 R216LS Service Manual CHAPTER 5. GENERAL INFORMA TION [1] GROUNDING INSTRUCTIONS This oven is equipped with a thr ee prong grounding plug. It must be plugged into a wall receptacle that is pr operly installed a nd grounded in accor- dance with the National Electrical Co de and local codes and ordinances. In the event of an electrical[...]

  • Seite 9

    R216LS 5 – 2 2. TOUCH CONTROL P ANE L NOTE: Some one-touch cooking features such as "MINUTE PLUS" are disabled after three minu tes when the oven is not in use. These features are automatically enabled when the door is opened and clos ed or the STOP/ CLEAR pad is pressed. POWER LEVEL STOP CLEAR MINUTE PLUS ST ART TIMER CLOCK POPCORN DEF[...]

  • Seite 10

    R216LS 6 – 1 R216LS Service Manual CHAPTER 6. OPERA T ION [1] DESCRIPTION OF OPERA TING SEQUENCE The following is a descript ion of com ponent functions dur ing oven operation. 1. OFF CONDITION Closing the door activates door sensing switch and secondary inter- lock switch. (In this condition, the monitor switch contact s are opened.) When oven i[...]

  • Seite 11

    R216LS 6 – 2 [2] OVEN SCHENA TIC 1. Off Condition Figure O-1. Oven Sche matic-Off Condition 2. Cooking Condition Figure O-2. Ove n Schematic-Cooking Co ndition SCHEMA TIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED 2. CLOCK APPEARS ON DISPLA Y SCHEMA TIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2. COOKING TIME PROGRAMMED. 3. V ARIABLE COOKING CONTROL &[...]

  • Seite 12

    R216LS 6 – 3 [3] DESCRIPTION AND F UNCTION OF COMPONENTS 1. DOOR OPEN MECHANISM The door is opened by p ushing the open button on the control panel, refer to the Figure D-1. When the open button is pushed, the open button pushes up the switch lever , and then the switch lever pushes up the latch head. The latch heads are moved upward and released[...]

  • Seite 13

    R216LS 7 – 1 R216LS Service Manual CHAPTER 7. TROUBLESHOOTING GUIDE Never touch any p art in the circuit with your hand or an uninsulated tool while the power sup ply is connected. When troubleshooting the microwave oven, it is he lpful to follow the Seq uence of Operation in performing the che cks. Many of th e possible cau ses of trouble will r[...]

  • Seite 14

    R216LS 8 – 1 R216LS Service Manual CHAPTER 8. TEST PROCEDURES [1] Procedure A: MAGNETRON ASSEMBL Y TEST 1. Disconnect the power supply cord, and then remove ou ter case. 2. Open the door and block it open. 3. Discharge high voltage cap acitor . 4. T o test for an open filament, isolate the magnetron from the high voltage circuit. A continuity che[...]

  • Seite 15

    R216LS 8 – 2 6. Reinstall the outer case (cabinet). 7. Reconnect the power supply cord after the outer case is installed. 8. Run the oven and check all functions. NOTE: Be sure to use an ohmmeter that will su pply a forward bias voltage of more than 6.3 volts. [4] Procedure D: HIGH VOL T AGE CAP ACITOR TEST 1. Disconnect the power supply cord, an[...]

  • Seite 16

    R216LS 8 – 3 7. Reconnect the power supply cord after the outer case is installed. 8. Run the oven and check all functions. 2. PRIMAR Y INTERLOCK RELA Y (RY2) 1. Disconnect the power supply cord, and then remove ou ter case. 2. Open the door and block it open. 3. Discharge high voltage cap acitor . 4. Disconnect two (2) wire leads from the male t[...]

  • Seite 17

    R216LS 8 – 4 [10] Procedure I: NOISE FIL TER TEST 1. Disconnect the power supply cord, and then remove ou ter case. 2. Open the door and block it open. 3. Discharge high voltage cap acitor . 4. Disconnect the lead wires from the terminal the noise filter . Using an ohmmeter , check between the terminals as described in the following tabl e. If in[...]

  • Seite 18

    R216LS 8 – 5 b) When touching the pads, no pads produce a signal. 2) In connection with indicators a) At a certain digit, all or some segments do not light up. b) At a certain digit, brightness is low . c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure [...]

  • Seite 19

    R216LS 8 – 6 These relays are operated by D.C. voltage Check voltage at the relay coil with a D.C. voltmeter during th e micr owave cooking operation. DC. voltage indicated ................. Defective relay . DC. voltage not indicated ........... Check diode which is connected to the relay coil. If diode is good, control unit i s defective. 8. If[...]

  • Seite 20

    R216LS 8 – 7 7) Follow the troubleshooting guide given below for r epair . 8) Disconnect the power supply cord and then remove outer case. 9) Open the door and block it open. 10)Discharge high voltage capacitor . 1 1) R econnect all leads removed from componen ts during testing. 12)Re-install the outer case (cabinet). 13)Reconnect the power suppl[...]

  • Seite 21

    R216LS 9 – 1 R216LS Service Manual CHAPTER 9. T OUCH CONTROL P ANEL ASSEMBL Y [1] OUTLINE OF TOUCH CONTROL P ANEL The touch control section consists of the following units as shown in the to uch control panel circuit. (1) Key Unit (2) Control Unit The principal functions of these units and their related signals are expla ined below . 1. Key Unit [...]

  • Seite 22

    R216LS 9 – 2 2) Open the door and block it open. 3) Discharge high voltage capacitor . 4) Disconnect the leads to the pr imary of the power transformer . 5) Ensure that these leads remain isolated from ot her components and oven chassis by using insulation tape. 6) After that procedure, re-connect the power supply cord. After checking the perform[...]

  • Seite 23

    R216LS 10 – 1 R216LS Service Manual CHAPTER 10. PRECAUTIONS FOR USING LEAD-FREE SOLDER [1] Employing lead-free solder The "Main PWB" of this mode l employs lead-free solder . This is ind icated by the "LF" symbol printed on the PWB and in the servi ce manual. The suf- fix letter indicates the alloy type of the solder . Examp l[...]

  • Seite 24

    R216LS 11 – 1 R216LS Service Manual CHAPTER 1 1. COMPONENT REPLACEMENT AND ADJUSTMENT PROCE- DURE [1] W ARNING Please refer to “OVEN P ARTS, CABINET P ARTS, CONTROL P ANEL P ARTS, DOOR P ARTS”, when carrying out any of the following removal pr oce- dures: [2] OUTER CASE REMOV AL T o remove the outer case, procedure as follows. 1. Disconnect t[...]

  • Seite 25

    R216LS 11 – 2 [3] MAGNETRON REMOV AL 1. Disconnect the power supply cord and remove outer case. 2. Open the oven door and block it open. 3. Discharge high voltage cap acitor . 4. Remove the two (2) screws holding the air duct to the oven cavity . 5. Release the air duct from the oven cavity . 6. Disconnect the wire leads from magnetron. 7. Remove[...]

  • Seite 26

    R216LS 11 – 3 3. Discharge high voltage cap acitor . 4. Push the lever of positive lock ® connector . 5. Pull down on the positive lock ® connector . CAUTION: WHEN CONNECTING THE POSITIVE LOCK ® CONNEC- TORS T O THE TERMINALS, INST ALL THE POSITIVE LOCK ® SO THA T THE LEVER FA CES YOU. Figure C-1. positive lock ® connector [7] CONTROL P ANEL[...]

  • Seite 27

    R216LS 11 – 4 [9] POWER SUPPL Y CORD REPLACEMENT 1. REMOV AL 1. Disconnect the power supply cord, and remove outer case. 2. Open the door and block it open. 3. Discharge high voltage cap acitor . 4. Remove the single (1) screw holding the green wire to the oven cavity back plate. 5. Disconnect the leads of the power supply cord from the noise fil[...]

  • Seite 28

    R216LS 11 – 5 8. Remove the fan blade assembly from the shaft of the fan motor by pulling and rotating the fan blade with your hand. 9. Now , the fan blade w ill be free. CAUTION: DO NOT RE-USE THE REMOVED F AN BLADE BECAUSE THE HOLE (FOR SHAFT) MA Y BE LARGER THAN NORMAL. 10.N ow , the fan motor is free. 2. INST ALLA TION 1. Install the fan blad[...]

  • Seite 29

    R216LS 11 – 6 2. Aft er adjustment, check the following. 1. In and out play of door remains less than 0.5mm w hen in the latched position. First check upper po sition of latch hook, pushing and pulling upper portion of door toward the oven face. Then check lower portion of the latch hook, pushing and pulling lower portion of the door toward the o[...]

  • Seite 30

    R216LS 11 – 7 NOTE: The door on a microwave oven is desig ned to act as an electronic seal preventing the leakag e of microwave energy from oven cavity du ring cook cycle. This fu nction does not re quire that door b e air-tight, m oisture (conden - sation)-tight or lig ht-tight. Therefore, occasio nal appear- ance of moisture, l ight or sensing [...]

  • Seite 31

    R216LS 12 – 1 R216LS Service Manual CHAPTER 12. CIRCUIT DIAGRAMS [1] Pictorial Diagram (Figure S-1) Figure S- 1. Pictoria l Diagram BLU MONITOR SWITCH SECONDARY INTERLOCK SWITCH COM COM RED N.C. N.O. N.O. COM GRY GRN GRN GRY TEMPERATURE FUSE (OVEN) DOOR SENSING SWITCH BLK ORG GRN CONTROL PANEL WHT RY1 PRIMARY INTERLOCK RELAY CN-B 2 1 CN-A N.O. CO[...]

  • Seite 32

    R216LS 12 – 2 [2] Control Panel Ci rcuit (Figure S-2) Figure S-2. Control Panel Circuit SEG14 AIN1 AIN0 SEG0 P20 VLC2 VLC1 VLC0 CAPL CAPH P70 AIN5 P03 COM0 IC-1 AIN2 AIN3 AIN4 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 P11 P10 P33 P32 P31 INTP0 P26 P25 AVSS P24 P23 P22 BZO90 1 48 32 49 64 16 33 B2 A1 RY1 DU12D1-1P(M)-R RY2 Q21 DTD143ES C21 10uF/35V +[...]

  • Seite 33

    R216LS 12 – 3 [3] Printed Wiring Board (Figure S-3) Figure S-3. Printed Wiring Board DIP CN-B C21 T1 S D2 P (J1) 1 C8 2 5 E Q22 B 21 SP1 Q21 (J12) (J13) (J14) (J15) E C2 R4 3 4 ZD1 D3 D4 D1 VRS1 RY2 RY1 CN-A 1 3 (J11) (J10) D20 D21 D40 D22 CHIP SIDE UNIT CODE[...]

  • Seite 34

    R216LS 12 – 4 MENO[...]

  • Seite 35

    P ARTS GUIDE SHARP CORPORATION Thi s document has been published to be used for after sales service only. The contents are subject to change witho ut notice. R216LS MICROW A VE OVEN MODEL CONTENTS R-216LS HOW TO ORDER RE PLACEMENT PARTS To have your order filled prom ptly and correctly, please furnish the fo llo wing information. 1. MODEL NUMBER 2.[...]

  • Seite 36

    R216LS 2 [1] OVEN PARTS 7-8 2-1 7-8 4-6 7-8 7-8 7-3 7-3 1-8 6-4 7-2 1-6 1-3 7-1 2-2 4-1 4-10 4-2 7-8 7-8 7-8 7-8 7-2 4-3 B 6-1 6-2 7-8 7-6 7-8 4-9 1-7 7-1 4-5 4-11 4-8 7-8 1-2 7-7 7-6 4-4 4-14 4-15 7-2 6-3 7-1 1-5 1-1 1-2 7-7 4-13 4-12 7-4 7-6 7-9 1-1 1-9 1-4 4-7 2-3 2-3 1-11 7-1 1-10 1-12 7-5 7-8 7-8 7-2[...]

  • Seite 37

    R216LS 3 NO. P ARTS CODE PRICE RANK NEW MARK PA R T RANK DESCRIPTION [1] OVEN PARTS ELECTRIC PART S 1-1 QSW-MA085WRE 0 AF Secondary interlock switch/ Door sensing switch 1-1 QSW-MA137WRE 0 AH Secondary interlock switch/ Door sensing switch (Interch angeable) 1-1 QSW-MA147WRZ Z AG Secondary interlock switch/ Door sensing switch (Interch angeable) 1-[...]

  • Seite 38

    R216LS 4 [2] DOOR AND CONTROL PANEL PARTS 6-6 5-5 5-4 5-6 5-7 5-1 6-5 3-1-1 3-1 3-1-3 3-1-4 3 3-6 3-5 3-4 3-3 3-2 3-2-1 3-2-2 Before attaching Control unit to Control panel, foil side of Control unit must be cleaned by ethyl- 3-1-2 B 5-3 5-2 5-2-2 5-2-1 5-2-3[...]

  • Seite 39

    R216LS 5 NO. P ARTS CODE PRICE RANK NEW MARK PA R T RANK DESCRIPTION [2] DOOR AND CONTROL PANEL PARTS 3-1 FPNLCB910WRK Z Control panel frame with key unit 3-1-1 PSHEPB193WRE Z AT Graphic sheet 3-1-2 QSW-KA068DRZ Z Membrane switch 3-1-3 GMADIA118WRR Z Display window 3-1-4 HDECQA236WRP Z AT Control panel decoration 3-2 FBTN-A146WRK Z AS Door open but[...]

  • Seite 40

    R216LS 6  INDEX P ARTS CODE No. PRICE RANK NEW MARK PA R T RANK [ D ] DPWBFC545WRUZ 2- 3-4 BH [ F ] FACCDA107WREZ 1- 1-3 AU FACCDA108WREZ 1- 1-3 AQ FBTN-A146WRKZ 2- 3-2 AS FDORFA397WRTZ 2- 5-1 BB FFS-BA026WRKZ 1- 1-2 AN FFS-BA038WRKZ 1- 1-2 AP FH-DZA114WRKZ 1- 1-4 AR FPNLCB910WRKZ 2- 3-1 FPWBFA385WRKZ 1- 1-12 AV FROLPA101WRKZ 1- 6-2 AR FWAKPA373[...]