SMC Networks SMC6608T Bedienungsanleitung

T igerSwitch 100 User Guide From SMC’s Tiger line of feature-rich workgroup LAN solutions March 1998 900.168 Rev. B[...]

SMC6608T SMC6608M T igerSwitch 100 8-port Fast Ethernet Switches ◆ T wo models featuring either: ◆ Eight fixed Auto-Negotiating 100BASE-TX ports ◆ T wo 4-port replaceable modules with 100BASE-TX and/or 100BASE-FX ports ◆ 1.6 Gbps internal bandwidth ◆ In-band and out-of-band management User Guide[...]

Information fur nished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However , no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC re[...]

Limited W arranty HARDW ARE: SMC Networks, Inc. (“SMC”) warrants these TigerSwitch 100 units to be free from defects in workmanship and materials, under normal use and service, for the following length of time from the date of purchase from SMC or its Authorized Reseller: TigerSwitch 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

SMC with a Return Material Authorization (RMA) number marked on the out- side of the package, and sent prepaid, insured, and packaged appropriately for safe shipment. The repaired or replaced item will be shipped to Customer , at SMC’s expense, not later than thirty (30) days after receipt by SMC. W ARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT[...]

Compliances .......................................................... v 1 About The T igerSwitch 100 ........................... 1-1 TigerSwitch 100 Overview ................................................. 1-3 Switch Architecture ............................................................. 1-10 Management Options ...............................[...]

Appendices A T r oubleshooting ............................................ A-1 Switch Indicators ................................................................. A-2 Diagnostic T ests .................................................................. A-3 System Diagnostics ............................................................. A-4 B Pin As[...]

List of Figur es 1-1. TigerSwitch 100T with 8 10BASE-T/100BASE-TX Ports (Model SMC6608T) ..................................................... 1-4 1-2. TigerSwitch 100M Base Unit...................................... 1-4 1-3. 4-Port Fast Ethernet Modules .................................... 1-4 1-4. 10BASE-T/100BASE-TX Ports .......................[...]

4-8. Virtual LAN Configuration Screen ............................. 4-18 4-9. System Information Screen ........................................ 4-21 4-10. Port Status Screen....................................................... 4-22 4-11. Statistics Screen .......................................................... 4-23 4-12. Address T able Screen[...]

FCC - Class A This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC Rules, which are [...]

Cet appareil numérique respecte les limites de bruits radioélectriques applica- bles aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur : "Appareils Numériques", NMB-003 édictée par l’Industrie. Japan VCCI Class A Australia AS/NZS 3548 (1995) - Class A SMC contact for products in Australia is[...]

Wichtige Sicher heitshinweise 1. Bitte lesen Sie diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. V or jedem Reinigen ist das Gerät vom Stromnetz zu trennen. V erwenden Sie keine Flüssigoder Aerosolreiniger . Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschluß steckdo[...]

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 14. W enn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen: a. Netzkabel oder Netzstecker sind beschädigt. b. Flüssig[...]

TigerSwitch 100 Overview . . . . . . . . . . . . . . . 1-3 Fast Ethernet Modules for Model SMC6608M . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Switch Ports . . . . . . . . . . . . . . . . . . . . . . . 1-6 10BASE-T/100BASE-TX Ports . . . . . . . . . 1-6 100BASE-FX Ports . . . . . . . . . . . . . . . . . 1-6 Status LEDs . . . . . . . . . . [...]

Management Options . . . . . . . . . . . . . . . . . . . 1-12 Serial Console Port . . . . . . . . . . . . . . . . . . 1-12 T elnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Key Features and Benefits . . . . . . . . . . . . . . . 1-13 Connectivity . . . . . . . . . [...]

T igerSwitch 100 Overview SMC’s TigerSwitch™ 100 units are intelligent Fast Ethernet switches. There are two TigerSwitch 100 models available. The first, the TigerSwitch 100T (SMC6608T) , features 8 fixed 10BASE-T/100BASE-TX ports. The predominance of dual- speed, Auto-Negotiating ports on the SMC6608T make this unit ideally suited for Fast Eth[...]

Figure 1-1. TigerSwitch 100T with 8 10BASE-T/100BASE-TX Ports (Model SMC6608T) Figure 1-2. TigerSwitch 100M Base Unit (Model SMC6608M) Figure 1-3. 4-port Fast Ether net Modules A BOUT THE T IGER S WITCH 100 1-4[...]

4-Port Fast Ethernet Modules for Model SMC6608M The avalable slide-in modules are listed below: 1-5 A BOUT THE T IGER S WITCH 100 SMC6600T 1-3 RJ-45 100BASE-TX, fixed crossover 4 RJ-45 100BASE-TX, switch- selectable crossover SMC6600F 1-4 SC 100BASE-FX, fiber SMC6600FSCT 1-2 SC 100BASE-FX, fiber 3 RJ-45 100BASE-TX, fixed crossover 4 RJ-45 100BASE-T[...]

Switch Ports 10BASE-T/100BASE-TX Ports These ports are dual-speed RJ-45 ports with built-in wiring crossovers. Each TigerSwitch 100 equipped with 10BASE-T/ 100BASE-TX ports will contain at least one straight-through (daisy-chain) port. This port is used for straight-through cable connections to other devices (i.e., hubs or switches) which have port[...]

Status LEDs The LEDs on the TigerSwitch 100 models are located on the front panel for easy viewing. For a more complete discussion of the front-panel LEDs, see Chapter 4, “Configuration and Management.” Figure 1-6. Fr ont Panel LEDs Figure 1-7. Fr ont Panel LED Array 1-7 A BOUT THE T IGER S WITCH 100[...]

Console Port Both TigerSwitch 100 units contain a Console port on the front panel. This is an RS-232 serial port with a DB-9 connector . A PC may be connected to this port for configuration and monitoring purposes out-of band via a full-handshaking null modem cable. (See Appendix B) Figure 1-8. Console Port Configure Button The Configure button is [...]

Optional Redundant Power Unit SMC’s Redundant Power Units (RPUs) are separate devices and each has its own power cord. These devices can supply power to the unit in the event of a failure of the internal power supply. The available RPUs are listed in the table below. Contact your reseller for advice regarding the appropriate RPU for your specific[...]

Switch Ar chitecture Switching Methods Adaptive Cut-Through SMC’s TigerSwitch 100 models employ a dynamic forwarding architecture that enables them to support adaptive cut-through frame forwarding mode. This approach allows the switch to automatically alternate between three different switching methods to provide the best possible performance in [...]

Spanning T ree Protocol The TigerSwitch 100 switches support the ANSI/IEEE 802.1d Spanning T ree Protocol. This protocol adds a level of fault tolerance by allowing two or more redundant connections to be created between a pair of LAN segments. When there are multiple physical paths between segments, the protocol will choose a single path and disab[...]

Management Options The TigerSwitch 100 units may be managed using any one of the following three methods: ♦ Out-of-band via the RS-232 console port ♦ In-band via T elnet ♦ In-band via any SNMP-based network management program that includes a compiler Serial Console Port The switches may be managed out-of-band using a PC connected to the conso[...]

Key Featur es and Benefits Connectivity • Slide-in, replaceable 4-port modules for added flexibility (Model SMC6608M only) • 100BASE-FX ports with SC or ST connectors (Model SMC6608M only) • Auto-Negotiation on 10BASE-T/100BASE-TX ports automatically selects optimum communication mode (half or full duplex and 10 Mbps or 100 Mbps) if this feat[...]

• Operates at maximum packet filtering and forwarding rate • Supports cut-through, store-and-forward, fragment-free and adaptive cut-through packet transport techniques • Routing table with over 4 K MAC address entries for attached network nodes • Automatically learns MAC addresses to build the routing information database • Fast hashing [...]

2-1 Introduction to Switching . . . . . . . . . . . . . . . . 2-2 Sample Applications . . . . . . . . . . . . . . . . . . . 2-3 Collapsed Backbone . . . . . . . . . . . . . . . . . 2-3 Multiport Bridging . . . . . . . . . . . . . . . . . . . 2-4 High-Speed Switch Links . . . . . . . . . . . . . . 2-5 Collapsed Backbone with Fiber Cable . . . . 2-6 [...]

Introduction to Switching An Ethernet or Fast Ether net switch allows simultaneous transmission of multiple packets via high-bandwidth shared memory. This means that it can partition a network more efficiently than bridges or routers. The switch is, therefore, fast being recognized as one of the most important building blocks for today’s networki[...]

Sample Applications The TigerSwitch 100 is not only designed to segment your network, but also to provide a wide range of options in setting up network connections. Some typical applications for the TigerSwitch 100 are described below. Collapsed Backbone The TigerSwitch 100 is an excellent choice for Ethernet installa- tions where significant growt[...]

Multiport Bridging With 8 parallel bridging ports (i.e., 8 distinct collision domains), the TigerSwitch 100 can collapse a complex network down into a single efficient bridged node, increasing overall bandwidth and throughput. In the figure below, the 10BASE-T/100BASE-TX ports on the TigerSwitch 100T (Model SMC6608T) are providing 100 Mbps connecti[...]

Server Far m Aggregation The advantages of mixed-media can also be easily exploited with the TigerSwitch 100M because of the various port configu- rations available among its 4-port modules. In the following example, a TigerSwitch 100M, equipped with modules featuring 10BASE-T/100BASE-TX and 100BASE-FX ports, is providing localized Fast Ethernet co[...]

High-Speed Switch Links Most common LAN implementations use a combination of hubs, bridges and routers. The bridges and routers quickly become bottlenecks, reducing overall network throughput. Using switches instead of bridges and routers allows you to tie together LAN segments and retain a cohesive LAN structure in which any node can freely commun[...]

2-7 PLANNING Collapsed Backbone with Fiber Cable Fiber optic technology allows for a longer cable run distance (up to 2 km in full-duplex) than any other media type. The TigerSwitch 100M, used as a collapsed backbone to interconnect multiple Fast Ethernet segments with fiber cable, is a convenient way to provide direct connectivity for a wide-sprea[...]

PLANNING 2-8 High-Speed Fiber Backbone When maximum network reach is required, the TigerSwitch 100M (Model SMC6608M) can be used to help create a high- speed fiber backbone. In the figure below, a TigerSwitch 100M employed as a collapsed backbone is also part of a full-duplex, 200 Mbps fiber backbone. Figure 2-6. High-Speed Fiber Backbone[...]

Application Notes 1. Full-duplex operation only applies to point-to-point access (e.g., when the switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. For network applications that actually require routers (e.g., interconnecting dissimilar network typ[...]

[...]

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . 3-2 Equipment Checklist . . . . . . . . . . . . . . . . . . . 3-3 Package Contents . . . . . . . . . . . . . . . . . . . 3-3 Required Rack-Mounting Equipment . . . . . 3-3 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Mounting the Switch in a Rack . . . . . . . . . [...]

Selecting a Site Before you start actual hardware installation, make sure you can provide the right operating environment, including power requirements, sufficient physical space and proximity to other network devices. V erify the following installation requirements: ◆ The site should: • be located in a cool, dry place, with at least 4 in. (10 [...]

Equipment Checklist Package Contents In addition to this user guide, the package should contain: ◆ one (1) TigerSwitch 100 switch • Model SMC6608T (8 10BASE-T/100BASE-TX ports) or • Model SMC6608M (2 4-port module slots with protective covering plates)* ◆ two (2) brackets with screws for rack mounting the unit ◆ four (4) rubber foot pads [...]

Mounting The TigerSwitch 100 is suitable for desktop or rack-mount installation. A good location is at the center of all the devices you want to link and near a power outlet. This switch can also be stacked with other switches on a flat surface or in a rack. Refer to the following sections: “Mounting the Switch in a Rack” and “Mounting and St[...]

T o rack mount the switch: 1. Attach the brackets to the device using the screws provided. Figure 3-1. Attaching the Brackets 2. Mount the device in the rack, using four rack-mounting screws. Figure 3-2. Installing the Switch in a Rack 3-5 I NSTALLA TION[...]

Mounting and Stacking the Switch on a Flat Sur face 1. Attach the four adhesive feet to the hollow spaces on the bottom of the switch. Figure 3-3. Attaching the Adhesive Feet 2. Set the switch on a flat surface near an AC power source, making sure there are at least 4 inches (10 cm) of space in the front and back for proper air flow. 3. T o stack s[...]

Powering Up Connecting to a Power Source 1. Power on the switch by plugging one end of the power cord into the power socket on the rear panel, and the other end into a power outlet. (See Chapter 2 for a description of the r ear-panel power r eceptacles) North America : Each switch is shipped with one standard AC line cord for North America (UL and [...]

I NSTALLA TION 3-8 3. Check to insure that the front-panel Power LED is lit. If not, check that the power cable is correctly plugged in. (Refer to Chapters 1 and 4 for detailed explanations of the LEDs.) Diagnostics Upon power up, the system performs an inter nal self-diagnostic test of major switch components. If any component fails during the tes[...]

Making Network Connections Switches are designed to interconnect multiple segments, or collision domains. Each segment may contain a single server or workstation, or multiple workstations that are connected to a hub. Connectivity Rules An overview of the rules for both Ethernet and Fast Ether net collision domains is provided below. 10 Mbps Etherne[...]

100 Mbps Fast Ethernet Collision Domain SMC 3 - 2 Rule for Class II Repeaters SMC 2 - 1 Rule for Class I and Class II Repeaters Maximum 100BASE-T Network Diameter Maximum 100BASE-T Cable Distance I NSTALLA TION 3-10 Between any two PCs or other stations in the same 100BASE-T collision domain, there may be: • up to 3 link segments and • up to 2 [...]

T wisted-Pair Cabling Guidelines Each 10BASE-T or 100BASE-TX connection requires an unshielded twisted-pair (UTP) cable with RJ-45 connectors at both ends. For 10BASE-T connections, two pairs of 100 Ohm Category 3, 4 or 5 cable are required. 100BASE-TX connections require two pairs of certified Category 5 cable. Every twisted-pair connection must h[...]

Connecting 10BASE-T/100BASE-TX Ports Fixed Crossover Ports Insert the RJ-45 connector on one end of a twisted-pair cable into an unused 10BASE-T/100BASE-TX port on the TigerSwitch 100, and the RJ-45 connector on the other end into a port on the other device. 1. Always use straight-through cable when connecting a server or workstation to the switch.[...]

Connecting 100BASE-FX Ports TigerSwitch 100M fiber modules are equipped with either SC or ST connectors. Connect one end of a fiber optic cable to the appropriate fiber connector on the front panel of the TigerSwitch 100M, and the other end to the connector on the other device. 1. The100BASE-FX ports require 50/125 or 62.5/125 µ core multimode fib[...]

[...]

Configuration Options . . . . . . . . . . . . . . . . . . 4-3 Basic Port Settings . . . . . . . . . . . . . . . . . . . . . 4-4 Advanced System Configuration . . . . . . . . . . . 4-5 Required Connections and Switch Access . . 4-5 Console Port (Out-of-Band) Connections 4-5 Remote Management via the Console Port 4-5 In-Band Connections . . . . . . .[...]

System Monitoring . . . . . . . . . . . . . . . . . . . . . 4-19 Monitoring via the Configure Button and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 Advanced System Monitoring . . . . . . . . . . . 4-21 System Information . . . . . . . . . . . . . . . . 4-21 Port Status . . . . . . . . . . . . . . . . . . . . . . . 4-22 Statistics .[...]

Configuration Options Basic port communication modes can be configured manually through the use of the front-panel Configure button. For more advanced management capability, the TigerSwitch 100 provides a menu-driven System Configuration Program which can be accessed through the Console Interface (out-of-band) or by a T elnet connection (in-band) o[...]

Basic Port Settings When using the Configure button to set port communication modes: 1. Use a long press (>2 seconds) to begin function selection. The Status LED will start to flash to indicate that functions may be selected. Use short presses (<2 seconds) to cycle through the status LEDs until the Full/Half LED lights. Use a long press to in[...]

Advanced System Configuration Required Connections and Switch Access Console Port (Out-of-Band) Connections 1. Plug the female end of a standard RS-232 null-modem cable into the switch connector labeled “Console”. Plug the other end of the cable into the serial connector on either a PC (typically COM1 or COM2) running a terminal emulation progr[...]

9600 and the A T command set is supported. Set the terminal emulation type on the PC to VT100 and specify which PC COM port is being used. Then, set communications to 8 data bits, 1 stop bit, no parity and the baud rate to 9600 or 19200 bps. The default rate is 9600 bps. Then, dial into the switch. Use a terminal emulation package to connect over t[...]

The System Configuration Program Login The System Configuration Program software types and versions appear on this screen. The default passwords for the System Configuration Program are “admin” and “guest”. The admin password provides administrator rights (i.e., Read/W rite access to configuration parameters and statistical information). Th[...]

Main Menu The Main Menu provides access to all the sub-menus necessary to configure and monitor the switch. Figure 4-2. System Configuration Pr ogram Main Menu Main Menu Items Information and Statistics: System Infor mation: Provides detailed system description. Statistics: Shows statistics for overall switch or each port. Spanning Tr ee Infor mati[...]

Configuration: System Configuration: Shows basic IP setup and identifies system by name, location and contact. SNMP Configuration: Configures communities and trap managers. Password Configuration: Sets Administrator and User passwords. V irtual LAN Configuration: Assigns switch ports to form up to 8 independent LAN groups. Port Configuration: Disab[...]

Setting Passwords 1. Highlight “ Password Configuration ” in the Main Menu and press <ENTER>. This will access the Password Configuration Screen (See below). Figure 4-3. Passwor d Configuration Screen 2. Highlight “ Set Administrator Password ” and press <ENTER> to password protect administrator rights (Read/W rite privileges). [...]

Console Port Configuration The communications parameters for the RS-232 port can be set using the System Configuration Program. Figure 4-3 (below) illustrates the factory default settings. Figure 4-4. Console Configuration Scr een 1. Highlight “ Console Configuration ” in the Main Menu and press <ENTER>. This will access the Console Confi[...]

System Parameter Configuration 1. Highlight “ System Configuration ” in the Main Menu and press <ENTER>. This will access the System Configuration Screen (See below). Figure 4-5. System Configuration Scr een 2. Highlight “ System Name ” and press <ENTER> to assign a name to identify the switch if the default entry (see above) is[...]

6. Highlight “ Default Gateway ” and press <ENTER> to set the default gateway IP address to which the unit will send IP packets destined for a different subnet. Press <ENTER> again to confirm entry. 7. Highlight “ Subnet Mask ” and press <ENTER> to set the sub- net mask corresponding to the assigned IP address. Press <E[...]

Port Configuration 1. Highlight “ Port Configuration ” in the Main Menu and press <ENTER>. This will access the Port Configuration Screen illustrated below. Figure 4-6. Port Configuration Scr een 2. Highlight the setting under the “ Enabled ” column for the chosen port and press <ENTER> to use the arrow keys to toggle between en[...]

5. Highlight the setting under the “ SwitchingMode ” column to adjust the switching method for the chosen port. Press <ENTER> to use the arrow keys to cycle through Cut-through (CT), Store-and-forward (S&F), Adaptive cut- through (A-CT) or Fragment-free (FgFree) modes. Press <ENTER> again to confirm the choice. 6. Highlight the [...]

Spanning T ree Configuration The Spanning T ree Protocol (STP) is used to detect and disable network loops and to provide link back-up. It requires certain parameter settings. The factory default settings (See Figure 4-6) should be acceptable in most networks. T o change the default settings, proceed as follows: Figure 4-7. Spanning Tree Configurat[...]

4. Highlight “ Hello T ime ” and press <ENTER> to input a value (1 to 10 seconds) for the rate at which hello frames are to be generated. Press <ENTER> again to confirm the chosen value. 5. Highlight “ Maximum Message Age ” and press <ENTER> to input a value (6 to 40 seconds) for the amount of time any port within the Span[...]

Virtual LAN Configuration Switches do not inherently support broadcast domains. Use the Virtual LAN Configuration screen (Figure 4-7) to assign any port on the switch to up to 8 broadcast domain groups*. All ports on the switch are assigned to a single group by default. Figure 4-8. Virtual LAN Configuration Scr een 1. Highlight “ Virtual LAN Conf[...]

System Monitoring The TigerSwitch 100 units can be monitored using either the front-panel Configure Button and LEDs, SNMP and T elnet or the Console Interface. Monitoring via the Configure Button and LEDs The Configure button may be used with the front-panel LEDs to display various system operations characteristics. T o set the display mode using t[...]

4-20 CONFIGURATION AND MANAGEMENT Status LEDs LEDs Functions Power Indicates that the switch is receiving power . RPU Indicates that the optional Redundant Power Unit is supplying power to the switch. Status Indicates that the LED array is displaying status information for each port (This is the default display mode). Tx/Rx (60%) Indicates that the[...]

Advanced System Monitoring These following display screens can be accessed through the System Configuration Program Main Menu under the Information and Statistics section. The following section headings reflect the items available in this area of the Main Menu. System Information This screen displays descriptive information about the switch. Figure[...]

Port Status This screen displays the current status of each port on the switch. Figure 4-10. Port Status Scr een Port Status Screen Items 4-22 CONFIGURATION AND MANAGEMENT Parameter Description Media Type Displays Port type (100BASE-FX, etc.) Enabled Shows whether the port is enabled Link Indicates whether a device is attached to the port and is tr[...]

Statistics This screen displays statistical information for any port or the entire switch, depending on the display mode chosen. (See Item 1 below) Figure 4-11. Statistics Scr een This screen provides the following options: 1. Highlight “ Display ” and press <ENTER> to select statistical display. Use arrow keys to cycle through display se[...]

Statistics Screen Items 4-24 CONFIGURATION AND MANAGEMENT Item Description Time Since Last Number of times this port (or whole switch) or Reset of Statistics address table has been reset since power on Local Frames Number of frames confined to this segment and Received not forwarded Forwarded Number of frames forwarded to another Frames segment Lea[...]

Address Table Figure 4-12. Addr ess T able Scr een This screen provides the following options: 1. Highlight “ Display ” and press <ENTER> to select address table display. Use arrow keys to cycle through display selections (Ports 1-8 or the whole switch). Press <ENTER> to confirm the choice. 2. Highlight “ More ” and press <EN[...]

Spanning T ree Information The screen illustrated in Figure 4-12 shows a summary of the Spanning T ree configuration. This screen is only accessible if the Spanning T r ee Protocol is enabled (See the section entitled, “Spanning Tr ee Configuration” in this chapter) . Figure 4-13. Spanning Tree Infor mation Screen CONFIGURATION AND MANAGEMENT 4[...]

Spanning T ree Infor mation Scr een Items 4-27 CONFIGURATION AND MANAGEMENT Parameter Description Hello Time Displays the rate (in seconds) at which hello frames are generated. Forward Delay The amount of time (in seconds) any port in the Spanning T ree will wait before changing states (i.e., listening to learning, etc.). Root Port The port on the [...]

Downloading System Softwar e System software updates can be downloaded either in-band via TFTP Protocol or out-of-band through the console port. Downloading software via TFTP is substantially faster than serial downloading through the console port. After either type of file transfer , the switch will automatically restart. Downloading via TFTP Prot[...]

4. Highlight “ Execute Network Download ” and press <ENTER>. The system will ask for confirmation. Press <ENTER> to initiate download after confirmation. Downloading via the Console Port Software update files can be downloaded through the Console port using any terminal emulation program that can transmit binary files using Xmodem c[...]

Resetting the Switch Figure 4-15. Reset Scr een This screen provides the following options: 1. Highlight “ Reset ” in the Main Menu and press <ENTER> to access the reset screen (Figure 4-14). 2. Highlight “ Display Diagnostics While Power-On ” and press <ENTER> to enable/disable diagnostic indicators during a reset. 3. Highlight[...]

SNMP Protocol . . . . . . . . . . . . . . . . . . . . . . . 5-2 MIB Objects . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 SNMP Parameter Configuration . . . . . . . . . . . 5-4 Assigning SNMP Agent Access Rights . . . . . 5-4 C HAPTER 5 M ANAGEMENT VIA SNMP 5-1[...]

SNMP Protocol SNMP (Simple Network Management Protocol) is a communica- tion protocol designed specifically for the purpose of managing devices or other elements on a network. Network equipment commonly managed with SNMP includes hubs, switches, bridges, routers and host computers. SNMP is typically used to configure these devices for proper operat[...]

the manager software, and result in a response by the agent. The third operation type, the TRAP , allows the agent to send an unsolicited message to the manager . This operation is typically used as an alert to a potential problem, or a change in device status. MIB Objects A number of different MIB specifications have been defined for managing netw[...]

SNMP Parameter Configuration In order to access the SNMP agent resident in the TigerSwitch 100 units, the switch must be configured with a valid IP address, default gateway and subnet mask. This is accomplished through the System Configuration Program, which can be accessed in-band or out-of-band (See Chapter 4, “Configuration and Management”) [...]

3. Highlight “ Community Strings ” and press <ENTER>. This will access the Community Strings screen (Figure 5-2). Figure 5-2. Community Strings Scr een 4. Highlight “ Add Entry ” and press <ENTER> to input a community name and its access mode.* The community name is the community string required for trap management access. The a[...]

5. Highlight “ T rap Receivers ” in the SNMP Configuration screen (Figure 5-1) and press <ENTER> to access the T rap Receivers screen (Figure 5-3). Figure 5-3. Trap Receivers Screen 6. Highlight “ Add Entry ” and press <ENTER> to input an IP Address for a receiver station and assign a community name and index for that station. R[...]

Switch Indicators . . . . . . . . . . . . . . . . . . . . . . A-2 Diagnostic T ests . . . . . . . . . . . . . . . . . . . . . . . A-3 System Diagnostic T ests . . . . . . . . . . . . . . . A-3 Port Diagnostic T ests . . . . . . . . . . . . . . . . . A-4 System Diagnostics . . . . . . . . . . . . . . . . . . . . A-4 Power and Cooling Problems . . . [...]

Switch Indicators The LED indicators on TigerSwitch 100 can be of assistance in identifying problems. Some common problems and possible solutions are described below. Symptom: Link LED does not light up (green) after making a connection. Cause: Network interface (e.g., network card on the attached device), network cable or switch port may be defect[...]

Diagnostic T ests Upon power-up, the TigerSwitch 100 units perform self- diagnostic tests (See Chapter 3). Diagnostic tests similar to those perfor med on power-up can be run using the Configure button: 1. Use a long press (>2 seconds) to begin function selection. The Status LED will start to flash to indicate that functions may be selected. Use[...]

Port Diagnostic T ests Port Diagnostic T ests, the second diagnostic test phase, check each port. The following table details port failures, which are indicated in the column of the LED array corresponding to the malfunctioning port: Port Failures System Diagnostics Power and Cooling Problems If the Power LED does not turn on when the power cord is[...]

Communication Mode The communication mode of each port (half or full duplex and 10 Mbps or 100 Mbps) must be identical to the mode of the attached device. V erify that each port is set to the same communication modes used by the attached device. Each 100BASE-FX port must be configured for half- or full-duplex operation. For each 10BASE-T/100BASE-TX[...]

down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation comply with recommendations. (See “Making Network Connections” in Chapter 3.) Management Inter face T er minal Emulation If the terminal attached to the console port is not operating properly, check that: 1. the a[...]

System Integrity As a last resort, verify the integrity of the switch with a power- on reset (See Chapter 4, “Configuration and Management”). If the problem still persists and you have completed all the preceding diagnoses, contact SMC T echnical Support for further assistance. Be sure to check the Login Screen (Figure 4-1.) for the version of [...]

[...]

RJ-45 Pin Assignments . . . . . . . . . . . . . . . . . . B-2 Straight-through Wiring . . . . . . . . . . . . . . . B-3 Crossover Wiring . . . . . . . . . . . . . . . . . . . . B-3 Console Port Pin Assignments . . . . . . . . . . . . B-4 A PPENDIX B P IN A SSIGNMENTS B-1[...]

RJ-45 Pin Assignments Caution: Regulations regarding the connection of equipment to telephone networks vary from country to country. Check with your local telephone network supplier before using existing telephone wiring. An Ethernet twisted-pair link segment requires two pairs of wires—Category 3, 4 or 5 for 10 Mbps connections and Category 5 fo[...]

Straight-Through Wiring If the twisted-pair link segment is to join two ports and only one of the ports has an internal crossover , the two pairs of wires must be straight-through. Crossover Wiring If the twisted-pair link segment is to join two ports and either both ports are labeled with an “x” or neither port is labeled with an “x,” a cr[...]

Console Port Pin Assignments The DB-9 serial console port on the front-panel is used to connect the switch to a console device, either directly or remotely. The pin assignments for connection to another DB-9 port or a DB-25 port are provided below and on the following pages. Note: Any cable connected to the Console port must be shielded to comply w[...]

Console Port to 9-Pin COM Port on PC Console Port to 25-Pin DCE Port on Modem B-5 P IN A SSIGNMENTS Switch Port PC Port DB-9 Pin No. Signal DB-9 Pin No. 1 (DCD) DCD 1 2 (RXD) TXD 3 3 (TXD) RXD 2 4 (DTR) DSR 6 5 (SGND) SGND 5 6 (DSR) DTR 4 7 (RTS) CTS 8 8 (CTS) RTS 7 9 (RI) RI 9 Switch Port 25-Pin Modem Port DB-9 Pin No. Signal DCE Pin No. 1 DCD 8 2[...]

Console Port to 25-Pin DTE Port on PC Null Modem Switch Port DB-9 Pin No. 1 (DCD) 2 (RXD) 3 (TXD) 4 (DTR) 5 (SGND) 6 (DSR) 7 (RTS) 8 (CTS) 9 (RI) 11 23 32 48 52 0 67 74 95 20 6 P IN A SSIGNMENTS B-6 25-Pin PC Port DTE Pin No. 8 (DCD) 3 (TXD) 2 (RXD) 20 (DTR) 7 (SGND) 6 (DSR) 4 (RTS) 5 (CTS) 22 (RI)[...]

All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Model SMC6608T . . . . . . . . . . . . . . . . . . . . . . C-4 Model SMC6608M . . . . . . . . . . . . . . . . . . . . . C-4 Fast Ethernet Modules . . . . . . . . . . . . . . . . C-4 A PPENDIX C S PECIFICA TIONS C-1[...]

All Models Switching Methods Adaptive Cut-through Cut-through Store-and-forward Fragment-Free Memory Buffer 256K per port Filtering/Forwarding/Lear ning Rates Full line rate MAC Address Table 4,096 entries Latency <20 µsec VLAN Support Port-based grouping, up to 8 groups with port overlapping Flow Control Back pressure mechanism (limits fiber c[...]

Full/Half Diagnostic LED Array Tx/Rx (60%) 100Mbps (30%) Full-Duplex (10%) Select/Link (1%) Button Configure Size 17.25 in. x 13.75 in. x 1.75 in. (43.8 cm x 34.9 cm x 4.4 cm) Input Power Universal AC input 100 to 240 V AC, 50 to 60 Hz Power Consumption 80 watts max @ 100-240 V AC Operating T emperatur e 0° C to 40° C (32° F to 104° F) Humidity[...]

Model SMC6608T Ports 8 10BASE-T/100BASE-TX, Auto-Negotiation support Network Inter face 10BASE-T RJ-45 connector , 100 Ohm, UTP cable; 2 wire pair; EIA/TIA Categories 3, 4, 5 100BASE-TX RJ-45 connector , 100 Ohm, UTP cable; 2 wire pair; EIA/TIA Category 5 W eight 8.2 lbs. (3.7 kg) Model SMC6608M W eight (without modules) 7.8 lbs. (3.5 kg) Fast Ethe[...]

Network Inter face 10BASE-T RJ-45 connector , 100 Ohm, UTP cable; 2 wire pair; EIA/TIA Categories 3, 4, 5 100BASE-TX RJ-45 connector , 100 Ohm, UTP cable; 2 wire pair; EIA/TIA Category 5 100BASE-FX SC or ST connector , multimode fiber cable, 50/125 or 62.5/125 µ core C-5 S PECIFICATIONS[...]

[...]

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2 A PPENDIX D G LOSSAR Y D-1[...]

10BASE-T IEEE specification for 10 Mbps Ethernet on two pairs of Category 3, 4 or 5 twisted-pair cable. The point-to-point cable segment can be up to 100 m (328 ft.) in length. 100BASE-FX IEEE specifications for 100 Mbps Fast Ethernet on multimode fiber optic cable. The maximum length for a point-to-point connection is 2 km (1.24 mi.) in full-duple[...]

Collision A condition in which packets transmitted over the cable interfere with each other . Their inter ference makes both signals unintelligible. Crossover Port An RJ-45 port which crosses the receive and transmit signals internally so it can be connected with straight-through twisted- pair cable to a workstation, server or any other device havi[...]

ICMP (Internet Contr ol Message Pr otocol) Commonly used to send echo messages (i.e., Ping) for monitoring purposes. In-Band A way of communicating with a network device from inside the network (i.e., a local connection). LED Light emitting diode used for monitoring a device or network condition. Local Area Network A group of interconnected compute[...]

T er minator A resistor placed at each end of a thick or thin coax cable to make sure that signals do not reflect back and cause errors. Simple Network Management Protocol (SNMP) The application protocol offering network management services in the Internet suite of protocols. Straight-through Port An RJ-45 port which does not cross the receive and [...]

Publication Number: 900.168, Rev . B FOR TECHNICAL SUPPORT , CALL: From U.S.A. and Canada (8:30 AM - 8:00 PM Eastern T ime) (800) SMC-4-YOU; (516) 435-6250; (516) 434-9314 (Fax) From Europe (8:00 AM - 5:30 PM UK Greenwich Mean T ime) 44 (0) 1344 420068; 44 (0) 1344 418835 (Fax) Bulletin Board Services (BBS) Modem settings: 9600,8,n,1 New Y ork: (51[...]