Snapper HZT21480BV, CZT19480KWV Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Snapper HZT21480BV, CZT19480KWV an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Snapper HZT21480BV, CZT19480KWV, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Snapper HZT21480BV, CZT19480KWV die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Snapper HZT21480BV, CZT19480KWV. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Snapper HZT21480BV, CZT19480KWV sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Snapper HZT21480BV, CZT19480KWV
- Den Namen des Produzenten und das Produktionsjahr des Geräts Snapper HZT21480BV, CZT19480KWV
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Snapper HZT21480BV, CZT19480KWV
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Snapper HZT21480BV, CZT19480KWV zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Snapper HZT21480BV, CZT19480KWV und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Snapper finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Snapper HZT21480BV, CZT19480KWV zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Snapper HZT21480BV, CZT19480KWV, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Snapper HZT21480BV, CZT19480KWV widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Safety Instructions & Operator’s Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 MODELS CZT19480KWV HZT21480BV MODEL NUMBER EXPLANATION C ZT 19 48 0 KWV MODEL DESIGNATION ENGINE TYPE DRIVE SYSTEM TYPE SERIES DESIGNATION ENGINE HP * MOWER DECK SIZE POWER UNIT C – Commercial Mid Mount 19 – Engine Horse Pow e r 48 – 48” Mow er Wid[...]

  • Seite 2

    IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these inst[...]

  • Seite 3

    3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, switches, blade controls and other safety dev ices frequently for proper operation and location. 9. Make sure all safe[...]

  • Seite 4

    4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only w ith a machine that has a hitch designed for tow ing. DO NOT attach tow ed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and tow ing on slopes. 3. DO NOT allow children or others on tow ed equipment. 4. On slopes, the w e[...]

  • Seite 5

    5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ........................................................................ 2-4 TABLE OF CO NTENTS ..................................................................................................... 5 SECTION 1 - FAMI LIARIZATI ON .....................................................................[...]

  • Seite 6

    6 Section 1 - FAMILIARIZATION FIGURE 1.1 1. 1 INTRODUCTION This manual has been prepared for the operators of the SNAPPER MID MOUNT ZERO TURNING HYDRO DRIVE. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and [...]

  • Seite 7

    7 Section 2 – SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PA RTS KEEP AWA Y FROM MOVING PA RTS MOTION CONTROL LEVER OPERA TION PARKING BRA KE LEVER OPERA TION WARNING ! AVOID SERIOUS INJURY OR DEA TH WEAR HEA RING PROTE CTION WARNING ! GUARD OR GRA SS CATCHER MUST BE INSTA LLED[...]

  • Seite 8

    8 Section 2 – SAFETY MESSAGES AND SYMBOLS DANGER! ROTATING BLA DES KEEP CHILDREN AND O THERS OUT OF MOWING A REA DANGER! ROTATING BLA DES KEYSWITCH HOUR METER PULL SWITCH “UP” TO ENGA GE BLA DES PUSH SWITCH “DOWN” TO DISENGA GE BLA DES CHOKE CONTROL ENGINE SPEED CONTROL CONTROL PANEL IDENTIFICA TION FAST SLOW RUN OFF/STOP START IGNITION S[...]

  • Seite 9

    9 WARNING DO NOT allow operation of the machine by untrained personnel. Section 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be[...]

  • Seite 10

    10 Section 3 - OPERATING INSTRUCTIONS ROLL RELEASE: To roll the machine without the engine running, pressure w ithin the hy draulic pumps must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a w rench to rotate both relief valves counter clockwise tw o full turns to op[...]

  • Seite 11

    11 Section 3 - OPERATING INSTRUCTIONS 3.2.2. STOPPING ENGINE 1. Stop engine by turning key to “STOP” position. Move engine speed to the Turtle “SLOW” position and turn key to “STOP”. See Figure 3.6. FIGURE 3.6 WARNING DO NOT operate blades in reverse. STOP blades. LOOK and SEE behind and dow n for children, pets, and hazards before and [...]

  • Seite 12

    12 Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Adjust cutting height, as desired, to any position, using deck lift lever. IMPORTANT: There is a foot assist pedal located to t he right front side of the footrest. Always use this assist pedal to raise or lower the deck to the desired cutting height. See Figure 3.10. 2. Insert [...]

  • Seite 13

    13 Section 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control levers to the neutral position & the neutral lock position. IMPORTANT: Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position. FIGURE 3.13 2. Engage parking brake. 3. Push Blade Switch dow[...]

  • Seite 14

    14 Section 4 - MAINTENANCE 4.1 INTRODUCTION To retain the quality of the SNAPPER mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular SNAPPER mower, always mention the model and serial number. SNAPPER recommends returning the mower to[...]

  • Seite 15

    15 Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BELT 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to mower drive belt. 4. Check the belt tension. If belt is frayed, slit, severed or belt strands exposed, replace belt before operating mower. Refer to Section “MOWER DRIVE BELT REP[...]

  • Seite 16

    16 Section 4 - MAINTENANCE 4.3.3. RIDING MO WER - LUBRICATION 1. Front Wheel Bearings Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. FIGURE 4.5 2. Hydro Pumps Check the level of the fluid in the fluid reservoir. Wipe away all dirt and debris from around reservoir cap before removing. Oil must rema[...]

  • Seite 17

    17 Section 4 - MAINTENANCE WARNING Allow engine to cool for at least ten minutes before performing service or maintenance. DO NOT smoke near fuel components w hen performing service or maintenance. DO NOT perform service and maintenance near an open flame. Wipe off any spilled fuel before starting engine. DO NOT run engine indoors. 4.5 ANNUALLY (EN[...]

  • Seite 18

    18 Section 4 - MAINTENANCE WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set parking brake. Remove key . Remove spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 4. 6 DE CK RE MO VA L (C[...]

  • Seite 19

    19 Section 5 - ADJUSTMENTS & REPAIR DANGER Exercise EXTREME CAUTION w hen making this adjustment, due to close proximity of mov ing parts. 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. Move the control levers to the center or neutral position to stop machine. IMPORTANT: Alw ays retu[...]

  • Seite 20

    20 Section 5 - ADJUSTMENTS & REPAIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. With motion control levers remaining in the neutral lock position, See F ig ur e 3. 7, hold connecting rod up to the activation assembly and check length of rod. Tie rod end bolt must align with the activation assembly. If bolt is not aligned[...]

  • Seite 21

    21 Section 5 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remov e spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 5.2.1. MOWER DECK A[...]

  • Seite 22

    22 Section 5 - ADJUSTMENTS & REPAIR WARNING DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remov e spark plug w ires and secure aw ay from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool. 5.3 TRACTION BELT T[...]

  • Seite 23

    23 Section 5 - ADJUSTMENTS & REPAIR FIGURE 5.12 5.6a MOTION LEVER HANDLEBAR ALIGNMENT Handlebars of both left and right Motion Control Levers should be aligned when levers are dropped from their neutral lock positions. See Figure 5.12a. If bars are not aligned: 1. Loosen bolts that secure handlebar adjustment brackets to lever blocks, and adjus[...]

  • Seite 24

    24 Section 5 - ADJUSTMENTS & REPAIR 5.8 ENGINE ADJUSTMENTS & REPAIR Refer to the engine owner’s manual for engine adjustments and/or repairs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 1. Inspect blade frequently for signs of excessive wear or damage. Replace blade when it reaches the wear limit. See Figure 5.14. 5.9.2. BLADE SH[...]

  • Seite 25

    25 Section 5 - ADJUSTMENTS & REPAIR WARNING Shield the positive terminal w ith terminal cover located on battery harness. This prevents metal from touching the positive terminal, w hich could cause sparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable must go to the ( + ) terminal. BLACK (Negative) c[...]

  • Seite 26

    26 Section 5 - ADJUSTMENTS & REPAIR 5.10.4. BATTERY TESTING 1. Remove battery. Refer to Section “BATTERY REMOVAL”. 2. Using a voltmeter, check the battery’s state of charge by comparing the voltmeter reading with the chart below. (Remember to hook the positive (red) lead of the voltmeter to the battery’s positive terminal, and the negat[...]

  • Seite 27

    27 Section 5 - ADJUSTMENTS & REPAIR 5.11 HYDRAULIC SYSTEM, PURGING After replacing or repairing hydraulic system components, one or both of the wheel drives may not pull properly. This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perform the following procedure to purge the a[...]

  • Seite 28

    28 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank 1. Battery dead. 1. Service battery. Engine 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Cl ean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNA PPER dealer. Engine Will Not Start 1. Bl[...]

  • Seite 29

    29 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move 1. Motion Control Levers in the neutral “N” posit ion. 1. Move Motion Controls to desired speed Loss Of Traction 2. Hydro. Pumps in roll release setting. 2. Ti gh ten re li ef va lve s. 3. Low transmission hy draulic oil level. 3. Bring hydraulic oil to proper lev[...]

  • Seite 30

    30 SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 9 X Initial Oil Change Page 14 X Periodic Oil Change Page 15 X* Air Cleaner Clean or Replace Engine Manual X** Spark Plug Replace Engine Manual X Fuel Filter Replace Page 17 X Engine Cooling System Clean Shroud &am[...]

  • Seite 31

    31 2 YEAR LIMITED WARRANTY (CZT UNITS) For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship[...]

  • Seite 32

    32 2 YEAR LIMITED WARRANTY (HZT UNITS) For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defecti[...]

  • Seite 33

    33 PRIMARY MAINTENANCE[...]

  • Seite 34

    34 PRIMARY MAINTENANCE[...]

  • Seite 35

    35 PRIMARY MAINTENANCE[...]

  • Seite 36

    36 PRIMARY MAINTENANCE[...]

  • Seite 37

    37 SNAPPER PRODUCT REGISTRATION FORM IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS (Complete the following informa tion on your Snapper purchase) Model Number __________________________________________________________ Serial Number __________________________________________________________ Date of Pu rchase ____________________________[...]

  • Seite 38

    38 NOTES[...]

  • Seite 39

    39 NOTES[...]

  • Seite 40

    40 Safety Instructions & Operator’s Manual for MID-MOUNT ZERO TURNING HYDRO DRIVE SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings. Read, Understa[...]