Tektronix MTG100, MTG300 Bedienungsanleitung

Service Manual MTG100 & MTG300 MPEG Generator 071-0616-50 W arning The servicing instructions are for use by qualified personnel only . T o avoid personal injury , do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service. www .tektr onix.com[...]

Copyright  T ektronix, Inc. All rights reserved. T ektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. T ektronix, Inc., P .O. Box 500, Beaverton, OR 97077 TEKTRONIX and TEK are reg[...]

  T ektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this warranty period, T ektronix, at its option, either will repair the defective product without charge fo[...]

[...]

MTG100 & MTG300 MPEG Generator Service Manual i T able of Contents General Safety Summary vii . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service Safety Summary ix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface xi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

T able of Contents ii MTG100 & MTG300 MPEG Generator Service Manual Clock Frequency Adjustment 5-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance Maintenance 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Related Maintenance Procedures 6-1 . . . . . [...]

T able of Contents MTG100 & MTG300 MPEG Generator Service Manual iii List of Figures Figure 2-1: Rear panel power connector and power switch 2-4 . . . . . . . . Figure 2-2: Fr ont panel power switch 2-5 . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 2-3: Elements of the menu system 2-7 . . . . . . . . . . . . . . . . . . . . . . . F[...]

T able of Contents  MTG100 & MTG300 MPEG Generator Service Manual Figure 6-6: Guide to r emoval procedures 6-17 . . . . . . . . . . . . . . . . . . . . . . . Figure 6-7: Cabinet r emoval 6-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 6-8: Fr ont-panel unit removal 6-22 . . . . . . . . . . . . . . . . . . .[...]

T able of Contents MTG100 & MTG300 MPEG Generator Service Manual  Figure 6-41: System dialog box 6-70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 6-40: Organization of the device err or codes 6-77 . . . . . . . . . . . . . . Figure 9-1: MTG100 and MTG300 block diagram 9–3 . . . . . . . . . . . . . . . Figure 9-2: M[...]

T able of Contents vi MTG100 & MTG300 MPEG Generator Service Manual List of T ables T able 1-1: Main pr oduct features 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T able 1-2: Functional characteristics 1-4 . . . . . . . . . . . . . . . . . . . . . . . . . . T able 1-3: Electrical characteristics 1-6 . . . . . . . . . . . . . .[...]

MTG100 & MTG300 MPEG Generator Service Manual vii General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. T o avoid potential hazards, use this product only as specified. Only qualified personnel should perform service pr ocedur es. Use Proper Power Cord.[...]

General Safety Summary viii MTG100 & MTG300 MPEG Generator Service Manual T erms in this Manual. These terms may appear in this manual:   W arning statements identify conditions or practices that could r esult in injury or loss of life.  Caution statements identify conditions or practices that cou[...]

MTG100 & MTG300 MPEG Generator Service Manual ix Service Safety Summary Only qualified personnel should perform service procedures. Read this Service Safety Summary and the General Safety Summary before performing any service procedures. Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person c[...]

Service Safety Summary  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual xi Preface This is the service manual for the MTG100 and MTG300 MPEG Generators. This manual contains information needed to service an MPEG generator to the module level. Manual Structure This manual is divided into sections, such as the Specifications and Theory of Operation . Further , some sectio[...]

Preface xii MTG100 & MTG300 MPEG Generator Service Manual  Mechanical Parts List includes a table of all replaceable modules, their descriptions, and their T ektronix part numbers. Manual Conventions This manual uses certain conventions that you should become familiar with. Some sections of the manual contain procedures for you to perform. T[...]

Preface MTG100 & MTG300 MPEG Generator Service Manual xiii Contacting T ektronix Phone 1Ć800Ć833Ć9200 * Address T ektronix, Inc. Department or name (if known) 14200 SW Karl Braun Drive P .O. Box 500 Beaverton, OR 97077 USA Web site www .tektronix.com Sales support 1Ć800Ć833Ć9200, select option 1 * Service support 1Ć800Ć833Ć9200, select[...]

Preface  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual xv Introduction This manual contains information needed to properly service the MTG100 and MTG300 MPEG Generators, as well as general information critical to safe and effective servicing. T o prevent personal injury or damage to the MPEG generator , consider the following before attempting service: [...]

Introduction xvi MTG100 & MTG300 MPEG Generator Service Manual T ektronix Service Offerings T ektronix provides service to cover repair under warranty as well as other services that may provide a cost-effective answer to your service needs. Whether providing warranty repair service or any of the other services listed below , T ektronix service [...]

MTG100 & MTG300 MPEG Generator Service Manual 1Ć1 Product Overview The MTG100 and MTG300 MPEG Generators store and playback MPEG-2 transport streams that are compliant with A TSC, DVB, and ARIB standards. The MPEG generators can automatically update the time stamp values of the transport stream in real time to support long term playout. T able[...]

Product Overview  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 1Ć3 Specifications This section is divided into two subsections. General Characteristics lists the functional, electrical, mechanical, and environmental characteristics of the MPEG generator . Certifications and Compliances lists the national and international standards to which the MPEG generator [...]

Specifications 1Ć4 MTG100 & MTG300 MPEG Generator Service Manual T able 1Ć2: Functional characteristics Characteristics Description General Analyzed TS standard MPEGĆ2, DVB, ARIB, A TSC Supported Packet format 188, 204, 208 bytes Loop mode No Update T ransport stream is output with no editing functions available. Auto Update T ransport strea[...]

Specifications MTG100 & MTG300 MPEG Generator Service Manual 1Ć5 T able 1Ć2: Functional characteristics (Cont.) Characteristics Description Delete packet MTG300 only T arget packet Deletes the selected item from the transport stream. If other items with the same PID value as the selected item exist in the transport stream and they are contain[...]

Specifications 1Ć6 MTG100 & MTG300 MPEG Generator Service Manual T able 1Ć2: Functional characteristics (Cont.) Characteristics Description SI header change MTG300 only T arget packets One selected item. If two or more sections are contained in one packet, all of the sections are changed by the operation. Number of packets 1 to 65535 packets [...]

Specifications MTG100 & MTG300 MPEG Generator Service Manual 1Ć7 T able 1Ć3: Electrical characteristics (Cont.) Characteristics Description External reference input Connector type BNC Frequency 27 MHz, 1 ppm recommended. Input level, typical 800 mV ± 200 mV (pĆp) Input impedance, typical 50  (at 27 MHz) ECL control input Connector type D[...]

Specifications 1Ć8 MTG100 & MTG300 MPEG Generator Service Manual T able 1Ć3: Electrical characteristics (Cont.) Characteristics Description ECL/TTL/L VDS output (serial) Connector type DĆsub, 25 pin (the same connector as Parallel output) Output level (Output on) (J310101 and above) Note: Do not connect the Asserted Low pins for singleĆend [...]

Specifications MTG100 & MTG300 MPEG Generator Service Manual 1Ć9 T able 1Ć3: Electrical characteristics (Cont.) Characteristics Description SSI output Complies with SMPTE 310M. Connector type BNC Impedance 75  Data rate 1 Mbps to 40 Mbps (Not managed when the data frequency is more than 40 Mbps.) Output voltage 800 mV ± 10 % Return loss ?[...]

Specifications 1Ć10 MTG100 & MTG300 MPEG Generator Service Manual T able 1Ć5: Environmental characteristics Characteristics Description T emperature Operating +5 _ Ct o+ 4 0 _ C NonĆoperating -20 _ Ct o+ 6 0 _ C Relative humidity Operating 20% to 80% (No condensation) Maximum wetĆbulb temperature 29.4 _ C NonĆoperating 5% to 90% (No conden[...]

Specifications MTG100 & MTG300 MPEG Generator Service Manual 1Ć1 1 Certifications and Compliances This subsection lists the national and international standards to which the MPEG generator complies. T able 1Ć6: Certifications and compliances Category Standards or description EC Declaration of Conformity - EMC Meets the intent of Directive 89/[...]

Specifications 1Ć12 MTG100 & MTG300 MPEG Generator Service Manual T able 1Ć6: Certifications and compliances (Cont.) Category Standards or description  %&&! ($(!& &!$+  $ % ! &% "$!'& + ( $ &am[...]

MTG100 & MTG300 MPEG Generator Service Manual 2Ć1 Installation Supplying Operating Power  . Read all information and heed all warnings in this subsection befor e connecting the MPEG generator to a power sour ce.   AC POWER SOURCE AND CONNECTION. The MPEG generator operates fr om a single-phase power sour ce.[...]

Installation 2Ć2 MTG100 & MTG300 MPEG Generator Service Manual T able 2Ć1: PowerĆcord conductor identification Conductor Color Alternate color Ungrounded (Line) Brown Black Grounded (Neutral) Light Blue White Grounded (Earthing) Green/Y ellow Green T able 2Ć2: Power cord identification Plug configuration Normal usage Option number North Ame[...]

Installation MTG100 & MTG300 MPEG Generator Service Manual 2Ć3 This MPEG generator operates with any line voltage from 100–240 V AC RMS with any line frequency from 48–63 Hz. Before plugging the cord in the outlet, be sure that the power supply voltage is proper . Operating Environment The following environmental requirements are provided [...]

Installation 2Ć4 MTG100 & MTG300 MPEG Generator Service Manual Applying and Interrupting Power Consider the following information when you power on or power off the MPEG generator , or when external power loss occurs. Connect the proper power cord from the rear panel power connector to the power system. Refer to T able 2-2 for power cord ident[...]

Installation MTG100 & MTG300 MPEG Generator Service Manual 2Ć5 Press the ON/STBY switch on the lower left side of the front panel to power on the instrument. Refer to Figure 2-2.    Figure 2Ć2: Front panel power switch The MPEG generator automatically runs diagnostics when the instrument i[...]

Installation 2Ć6 MTG100 & MTG300 MPEG Generator Service Manual Repackaging Instructions If you ship the MPEG generator , pack it in the original shipping carton and packing material. If the original packing material is not available, package the instrument as follows: 1. Obtain a corrugated cardboard shipping carton with inside dimensions at l[...]

MTG100 & MTG300 MPEG Generator Service Manual 2Ć7 Operating Instructions Before servicing the MPEG generator , read the following operating instructions. These instructions are at the level appropriate for servicing the MPEG generator . The user manual contains complete operator instructions. Using the Menu System This section describes the ba[...]

Operating Instructions 2Ć8 MTG100 & MTG300 MPEG Generator Service Manual The pull-down menus are displayed in the Menu bar at the top of the screen. Y ou can operate these menus using the front panel MENU button, the right and left control buttons, the arrow buttons, and the rotary knob (see Figure 2-4). Accessing PullĆdown Menu Commands. The[...]

Operating Instructions MTG100 & MTG300 MPEG Generator Service Manual 2Ć9        Figure 2Ć5: Example of a displayed pullĆdown menu When a pull-down menu is displayed, the knob icon is displayed at the upper- right side of th[...]

Operating Instructions 2Ć10 MTG100 & MTG300 MPEG Generator Service Manual The Bezel menu displays a variety of commands. The commands change to correspond to the transport stream item selected by the Icon cursor in the hierarchy display , or to correspond to functions in a displayed dialog box. Accessing Bezel Menu Commands. The Bezel menu app[...]

Operating Instructions MTG100 & MTG300 MPEG Generator Service Manual 2Ć1 1 Y ou can enter numeric values in displayed dialog boxes by using the hexadeci- mal keypad or by using the rotary knob. Numeric Input Using the Hexadecimal Keypad. Perform the following procedure to input numeric values. Figure 2-8 shows the hexadecimal keypad. 1. Select[...]

Operating Instructions 2Ć12 MTG100 & MTG300 MPEG Generator Service Manual     Figure 2Ć9: Dialog box showing knob icon and underscore character Perform the following procedure to change a value using the rotary knob: 1. Select the numeric parameter you want to ch[...]

Operating Instructions MTG100 & MTG300 MPEG Generator Service Manual 2Ć13 The MPEG generator displays a pop-up message box that prompts you to confirm operations that will be difficult to recover from. An example of a pop-up message box is shown in Figure 2-1 1, which shows the message box for confirming that you want to defragment the TS driv[...]

Operating Instructions  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 3Ć1 Theory of Operation This section describes the basic operation of the major circuit blocks or modules in the MPEG generator . The Diagrams section, beginning on page 9-1, includes a block diagram and an interconnect diagram. Figure 9-1 shows the modules and functional blocks of the MPEG generat[...]

Theory of Operation 3Ć2 MTG100 & MTG300 MPEG Generator Service Manual started, the BUFFER LED on the front panel lights, unless the output buffer empty . This block updates the PCR and PTS/DTS values, interfaces the peripheral circuit of the output buffer/clock and the CPU module, and converts parallel format data to SSI format data. For updat[...]

Theory of Operation MTG100 & MTG300 MPEG Generator Service Manual 3Ć3 address decoder . The PCI Interface board provides the communication between the CPU module and A10 board and A40 board. The fourth slot of the Backplane contains the Ethernet LAN interface board. The MPEG generator has a 100 BASE-T/10 BASE-T connector on the rear panel. A30[...]

Theory of Operation  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 4Ć1 Performance V erification This section provides procedures that verify the performance of the MPEG generator . These tests confirm performance and functionality when the following conditions are met:  The MPEG generator must be operating in an environment that is within the operating limits [...]

Performance V erification 4Ć2 MTG100 & MTG300 MPEG Generator Service Manual *"  *&)"  ! &!$ *"  *&)"  ! &!$             Figure 4Ć1: Custom cable with 9Ćpin and 25Ćpin, DĆtyp[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć3 Procedures The following conventions are used in the performance verification procedures:  Each test lists the characteristic that is being tested and the equipment required to perform the test.  Each test contains complete setup instructions, which allows you to[...]

Performance V erification 4Ć4 MTG100 & MTG300 MPEG Generator Service Manual This test verifies the frequency of the MPEG generator ’ s internal clock. The following equipment and MPEG test signal is required for this test:  Frequency counter  Probe  test64.trp MPEG test signal Perform the following procedure to verify the internal c[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć5 This test verifies that transport stream data is output correctly from the ASI OUT connector on the MPEG generator . The following equipment and MPEG test signal is required for this test:  Oscilloscope  MPEG test system  75 W BNC cable  75 W to 50 W minimu[...]

Performance V erification 4Ć6 MTG100 & MTG300 MPEG Generator Service Manual      !         !   "  !!"! Figure 4Ć3: Ini[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć7   !                   Figure 4Ć4: Second equipment c[...]

Performance V erification 4Ć8 MTG100 & MTG300 MPEG Generator Service Manual  !             !   "  !!"! Figure 4Ć5: Ini[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć9 7. Disconnect the BNC cable from the 75 W to 50 W minimum loss attenuator on the oscilloscope’ s input, and then connect the BNC cable to the SSI IN connector on the MPEG test system’ s Real Time Analyzer as shown in Figure 4-6. 8. Use the parallel interface cable [...]

Performance V erification 4Ć10 MTG100 & MTG300 MPEG Generator Service Manual 17. In the Real T ime Analyzer window , click the Stop Analysis toolbar button to stop analysis. 18. Press the ST AR T/STOP button on the MPEG generator to stop the signal output, and then remove the BNC cable from the SSI OUT connector . This test confirms that trans[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć1 1                [...]

Performance V erification 4Ć12 MTG100 & MTG300 MPEG Generator Service Manual This test confirms that transport stream data is output correctly in serial format from the ECL/TTL/L VDS OUT connector on the MPEG generator . The following equipment and MPEG test signal is required for this test:  MPEG test system  Parallel interface cable ?[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual  7. Double-click the Data Store Administrator icon in the MPEG test system’ s Program Group window to start the application. 8. In the Data Store Administrator window , click the A (acquisition) command button to open the Acquisition settings window . 9. In th[...]

Performance V erification 4Ć14 MTG100 & MTG300 MPEG Generator Service Manual This test confirms that the external clock input (ECL CONTROL input) on the MPEG generator is functioning correctly . The following equipment and MPEG test signal is required for this test:  MPEG test system  75 W BNC cable  Custom 9-pin to 25-pin, D-type int[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual  4. Select Clock... from the OUTPUT menu on the MPEG generator to open the Clock dialog box. 5. Select EXT CLOCK in the Clock dialog box, and then press the OK bezel button. 6. Select Interface : Serial from the OUTPUT menu on the MPEG generator , and then press[...]

Performance V erification 4Ć16 MTG100 & MTG300 MPEG Generator Service Manual 20. In the Real T ime Analyzer window , click the Start Analysis toolbar button. 21. V erify that the Hierarchic view is displayed on the screen and that no error messages appear . In addition, verify that the transmission rate is 40 Mbps and that the transport stream[...]

Performance V erification MTG100 & MTG300 MPEG Generator Service Manual 4Ć17 MPEG generator rear panel 75  BNC cable Signal generator (HP 8648) 50  BNC cable NĆtoĆBNC adapter MPEG test system rear panel (MTS200 or MTS215 Opt. SS) Figure 4Ć10: Equipment connections for verifying the external reference input 5. Select Clock... from the [...]

Performance V erification  MTG100 & MTG300 MPEG Generator Service Manual 15. In the Real T ime Analyzer window , click the Start Analysis toolbar button. 16. V erify that the Hierarchic view is displayed on the screen and that no error messages appear . In addition, verify that the transmission rate is 64 Mbps and that the transport[...]

MTG100 & MTG300 MPEG Generator Service Manual 5Ć1 Adjustment Procedures This section contains information needed to adjust the MPEG generator . The only adjustment in the MPEG generator is for the clock frequency . Requirements for Adjustment Before doing the adjustment, note the following requirements. This procedure is only to be performed b[...]

Adjustment Procedures 5Ć2 MTG100 & MTG300 MPEG Generator Service Manual Clock Frequency Adjustment T o perform the clock frequency adjustment, you must first remove the cabinet. For removal and installation procedures for the cabinet, refer to Cabinet on page 6-18. After you have removed the cabinet, find the test point and adjustment pod on t[...]

Adjustment Procedures MTG100 & MTG300 MPEG Generator Service Manual 5Ć3   T o avoid serious injury , do not touch exposed connections or components when operating the instrument with the pr otective enclosur e r emoved. Danger ous potentials exist at several points within the MPEG generator . Initial Setups. Frequency c[...]

Adjustment Procedures  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć1 Maintenance This section contains the information needed to do periodic and corrective maintenance on the MPEG generator . The following subsections are included:  Pr eparation — Introduction plus general information on preventing damage to internal modules when doing maintenance.  Insp[...]

Maintenance 6Ć2 MTG100 & MTG300 MPEG Generator Service Manual Preparation Before servicing this product, read the Safety Summary and Intr oduction at the front of the manual and the ESD information below .  Static dischar ge can damage any semiconductor component in the MPEG generator . When performing any service which[...]

Maintenance MTG100 & MTG300 MPEG Generator Service Manual 6Ć3 T able 6-1 lists the relative susceptibility of various classes of semiconductors. Static voltages of 1 kV to 30 kV are common in unprotected environments. T able 6Ć1: Relative susceptibility to staticĆdischarge damage Semiconductor classes Relative susceptibility levels 1 MOS or [...]

Maintenance 6Ć4 MTG100 & MTG300 MPEG Generator Service Manual Inspection and Cleaning Inspection and Cleaning describes how to inspect for dirt and damage. It also describes how to clean the exterior and interior of the MPEG generator . Inspection and cleaning are done as preventive maintenance. Preventive maintenance, when done regularly , ma[...]

Maintenance MTG100 & MTG300 MPEG Generator Service Manual 6Ć5 T able 6Ć2: External inspection check list Item Inspect for Repair action          ?[...]

Maintenance 6Ć6 MTG100 & MTG300 MPEG Generator Service Manual Inspection Ċ Interior . T o access the inside of the MPEG generator for inspection and cleaning, refer to the Removal and Installation Pr ocedur es in this section. Inspect the internal portions of the MPEG generator for damage and wear , using T able 6-3 as a guide. Defects found [...]

Maintenance MTG100 & MTG300 MPEG Generator Service Manual 6Ć7 Cleaning Procedure Ċ Interior . T o clean the MPEG generator interior , perform the following steps: 1. Blow off dust with dry , low-pressure, deionized air (approximately 9 psi). 2. Remove any remaining dust with a lint-free cloth dampened in isopropyl alcohol (75% solution) and r[...]

Maintenance  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć9 Removal and Installation Procedures This subsection contains procedures for removal and installation of all mechani- cal and electrical modules. Any electrical or mechanical module, assembly , or part listed in Section 10 of this manual is a module. Preparation   Befor e[...]

Removal and Installation Procedures 6Ć10 MTG100 & MTG300 MPEG Generator Service Manual Section 10 lists all modules.  . Read these general instructions befor e removing a module. First r ead over the Summary of Procedures that follows to understand how the pr ocedur es ar e grouped. Then r ead Equipment Required for a list of the t[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć1 1 Equipment Required. Most modules in this MPEG generator can be removed with a screwdriver handle mounted with a size #2, Phillips tip. Use this tool whenever a pr ocedur e step instructs you to remove or install a scr ew unless a different size scr ewdriver[...]

Removal and Installation Procedures 6Ć12 MTG100 & MTG300 MPEG Generator Service Manual In this manual, procedures refer to “front,” “back,” “top,” etc. of the MPEG generator . Figure 6-1 shows how the sides are referenced. Figure 6Ć1: MPEG generator orientation MPEG Generator Orientation[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć13                 ?[...]

Removal and Installation Procedures 6Ć14 MTG100 & MTG300 MPEG Generator Service Manual                  ?[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć15   #  !"!  !      "!     ?[...]

Removal and Installation Procedures 6Ć16 MTG100 & MTG300 MPEG Generator Service Manual             Figure 6Ć5: Rear panel modules[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć17 Access Procedure When you have identified the module to be removed for service, read General Instructions found on page 6-10. Then use the flowchart in Figure 6-6 to determine which procedures to use for removing the module. The removal procedures end with i[...]

Removal and Installation Procedures 6Ć18 MTG100 & MTG300 MPEG Generator Service Manual Procedures for External Modules Do the Access Pr ocedur e (page 6-17) before doing any procedure in this group. This group contains the following procedures:  Line Cor d  Cabinet  Fr ont-Panel Unit  Fr ont-Panel Assembly 1. Assemble equipment and[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual  d. Grasp the right and left edges of the cabinet toward the back. Push against the chassis rear panel, toward the front of the MPEG generator , to separate it from the cabinet. e. Slide the cabinet off the MPEG generator . T ake care not to bind or sn[...]

Removal and Installation Procedures 6Ć20 MTG100 & MTG300 MPEG Generator Service Manual Figure 6Ć7: Cabinet removal[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć21 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size #2 Phillips tips (Items 1 and 3). b. Locate the module to be removed in the locator diagram External modules , Figure 6-2, page 6-13. 2. Orient instrument: Set th[...]

Removal and Installation Procedures 6Ć22 MTG100 & MTG300 MPEG Generator Service Manual        Figure 6Ć8: FrontĆpanel unit removal 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a 1/16 inch hex wrench (Item 19) and a screwdriver with a size #2 Phillips tips (Item[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual  3. Remove the A35 Power Switch: See Figure 6-9. a. Using a screwdriver with a size #2 Phillips tip, remove the screw securing the A35 board to the front cover . b. Unplug the cable from the A30 Front Panel board. c. Lift the board away . 4. Remove the[...]

Removal and Installation Procedures 6Ć24 MTG100 & MTG300 MPEG Generator Service Manual                   [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć25 Procedure for Internal Modules Perform the Access Pr ocedur e (on page 6-17) before doing any procedure in this group. The procedures are presented in the order listed:  Fan  Floppy Disk Drive  Data Har d Disk Drive  System Har d Disk Drive  D[...]

Removal and Installation Procedures 6Ć26 MTG100 & MTG300 MPEG Generator Service Manual   Figure 6Ć10: Fan removal 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size #1 and a size #2 Phillips tips (Items 1, 2, and 3). b. Locate the module to be removed in the locator diagram [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć27 f. Unplug the floppy disk connector (ribbon interconnect cable) that connects the disk drive to the A40 MISC (Power Distribution & Interface) board. 4. Remove floppy disk drive fr om bracket: Using a screwdriver with a size #1 Phillips tip, remove the tw[...]

Removal and Installation Procedures 6Ć28 MTG100 & MTG300 MPEG Generator Service Manual  . Read Replacing the Hard Disk Drive(s) on page 6-71, befor e performing the following pr ocedur es. 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size Phillips #2 tip (Items 1 and 3). b. Locate the m[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć29      Figure 6Ć12: Data hard disk drive removal       [...]

Removal and Installation Procedures 6Ć30 MTG100 & MTG300 MPEG Generator Service Manual  . Read Replacing the Hard Disk Drive(s) on page 6-71, befor e performing the following pr ocedur es. 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size Phillips #2 tip (Items 1 and 3). b. Locate the m[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć31             Figure 6Ć14: System hard disk drive removal[...]

Removal and Installation Procedures 6Ć32 MTG100 & MTG300 MPEG Generator Service Manual 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size #1 and a size #2 Phillips tips (Items 1, 2, and 3). b. Locate the module to be removed in the locator diagram Internal modules, Figure 6-3, page 6-14. 2. Orient t[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć33                        ?[...]

Removal and Installation Procedures 6Ć34 MTG100 & MTG300 MPEG Generator Service Manual This procedure describes how to remove these modules:  5 V Power Supply  12 V Power Supply  Power Switch  RFI Filter 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size #2 Phillips tip (Items 1 and 3). [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć35                          ?[...]

Removal and Installation Procedures 6Ć36 MTG100 & MTG300 MPEG Generator Service Manual b. Use a flat–bladed screwdriver to press down on top of the power switch and push the switch out of the Bracket. 7. Remove the RFI filter : See Figure 6-17. a. Unplug the two cables from the RFI filter . b. Using a screwdriver with a size Phillips #2 tip,[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć37 Procedure for Board Modules and CPU Unit Perform the Access Pr ocedur e (on page 6-17) before performing any procedure in this group. The procedures are presented in the order listed:  A10 Main Boar d  A40 MISC (Power Distribution & Interface) Boar[...]

Removal and Installation Procedures 6Ć38 MTG100 & MTG300 MPEG Generator Service Manual 4. Reinstallation: Perform step 3 in reverse order to reinstall the A10 Main board.           Figure 6Ć18: [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć39 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a size Phillips #2 tip (Items 1 and 3) and a 5 mm size nut driver (Item 12). b. Locate the modules to be removed in the locator diagram Boar d modules and CPU unit, Figu[...]

Removal and Installation Procedures 6Ć40 MTG100 & MTG300 MPEG Generator Service Manual 4. Reinstallation : Perform step 3 in reverse order to reinstall the A40 MISC (Power Distribution & Interface) board.           [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć41 This procedure describes how to remove these circuit boards contained in the CPU unit:  CPU Boar d  A20 Interface Boar d  LAN Boar d  Backplane 1. Assemble equipment and locate modules to be r emoved : a. Y ou need a screwdriver with a size Phill[...]

Removal and Installation Procedures 6Ć42 MTG100 & MTG300 MPEG Generator Service Manual                      [...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć43          Figure 6Ć21: CPU, A20 Interface, and LAN boards removal 5. Remove the A20 Interface Board : a. Using a screwdriver with a [...]

Removal and Installation Procedures 6Ć44 MTG100 & MTG300 MPEG Generator Service Manual 6. Remove the LAN Board : a. Using a screwdriver with a size Phillips #2 tip, remove the screw on the left side of the LAN board. See Figure 6-21. b. Grasp the board and slide it out. 7. Remove the Backplane : a. Unplug the power cable on the right side of t[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć45 b. Using the open-end wrench, unscrew the nut securing the BNC connector to the chassis. c. Pull out the BNC cables from the chassis. 4. Reinstallation: Perform step 3 in reverse order to reinstall the BNC cable assembly . 1. Assemble equipment and locate mo[...]

Removal and Installation Procedures 6Ć46 MTG100 & MTG300 MPEG Generator Service Manual 1. Assemble equipment and locate modules to be r emoved: a. Y ou need a screwdriver with a 1/4–inch nut driver (Item 5). b. Locate the modules to be removed in the locator diagram Rear panel modules , Figure 6-5, page 6-16. 2. Orient instrument: Set the MP[...]

Removal and Installation Procedures MTG100 & MTG300 MPEG Generator Service Manual 6Ć47  !  !  !"  !  !  !"  !  !  !"  !  !  !"      ?[...]

Removal and Installation Procedures  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć49 T roubleshooting This subsection contains information about diagnostics and the Service menu, and troubleshooting trees designed to isolate faulty modules in the MPEG generator . Diagnostics The MPEG generator has internal diagnostics that verify circuit functionality . The diagnostics are aut[...]

T roubleshooting 6Ć50 MTG100 & MTG300 MPEG Generator Service Manual T able 6Ć6: Error messages at power on diagnostics (Cont.) Error messages Solution CW H/W Error! Communication fail Check and replace the W330 and W331 cable assemblies. See Figure 9Ć2. HDC Logical Error! Directory error . Y ou need to format the TS data disks and execute Sc[...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć51 6. Select the bezel menu item you want to execute. T able 6-7 lists all the bezel menu items in the Service menu. T able 6Ć7: Bezel menu items in the Service menu Bezel menu items Descriptions TS Drive... Quick Format Initializes the file tables of the MTG file system. All th[...]

T roubleshooting 6Ć52 MTG100 & MTG300 MPEG Generator Service Manual When you execute the Simple Scandisk or Normal Scandisk command, the test result is saved as a file (/ide0/scandisk.res). Using this test result, you can check the number of clusters where errors were detected and clusters where errors were recovered. This file is not deleted [...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć53 T roubleshooting T rees T o (A), page 6Ć55. Start Y es No Are the fans working? Y es No Do the PLL, BUFFER, and EXT LEDs light? Y es No Does the start up display appear? Y es No Does the power on diag display? Y es No T o (B), page 6Ć57. T o (C), page 6Ć58. Is the P ASS dis[...]

T roubleshooting 6Ć54 MTG100 & MTG300 MPEG Generator Service Manual No Does the hierarchy display appear? Ye s No Do the PLL, BUFFER, and HDD LEDs light when the ST ART/STOP button is pressed? T o Data HDD, page 6Ć62. Ye s No Can a TS file be selected by the rotary knob? T o (E), page 6Ć60. Ye s 1 T o System HDD, page 6Ć64. Done. Figure 6Ć[...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć55 Ye s Are J290 and J295 on the A40 MISC board (see Figure 6Ć36) at +12 V? No No Is pin 7 of J030 on A40 MISC board (see Figure 6Ć36) at +5 V? Replace 12 V power supply . Ye s No Are the fan cables securely installed in their sockets? Securely install the cables , and then ins[...]

T roubleshooting 6Ć56 MTG100 & MTG300 MPEG Generator Service Manual Replace F040 on the A40 MISC (Power Distribution & Interface) board. (See Figure 6Ć36) Ye s Is J40 on the A40 MISC board (see Figure 6Ć36) at GND when the ON/STBY button is pressed? No No Is AC input to 5 V power supply? Check A35 Power Switch board, A30 Front Panel boar[...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć57 No Ye s Are pins 13, 16, 20, and 24 of J250 on A30 Front Panel board at +5 V? Replace the A30 Front Panel board. (B) Power off and remove the cabinet using the Cabinet removal procedure. and then remove the A10 Main board. Check W250. Remove the front panel using the Front Pan[...]

T roubleshooting 6Ć58 MTG100 & MTG300 MPEG Generator Service Manual No Ye s Does the backlight of the LCD module turn on? (C) Power off and remove the cabinet using the Rear Cover and Cabinet removal procedure. and then remove the A10 Main board. Short between pin 2 and 3 of J278 on the A40 MISC (Power Distribution & Interface) board (see [...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć59 No Ye s Is the HDC LOGICAL ERROR reported? T o Data HDD, page 6Ć62. (D) Is the F AIL reported for A30 Front Panel board? Ye s Replace the A30 Front Panel board. No Are any failures other than above reported? Ye s Replace the A10 Main board. (b) Figure 6Ć29: T roubleshooting [...]

T roubleshooting 6Ć60 MTG100 & MTG300 MPEG Generator Service Manual No Ye s Is the cable of the rotary encoder securely installed to J300 on the A30 Front Panel board? Replace the rotary encoder . (E) Power off and remove the cabinet using the Rear Cover and Cabinet removal procedure. and then remove the A10 Main board. Replace the front panel[...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć61 Replace F040 on the A40 MISC (Power Distribution & Interface) board. (See Figure 6Ć36) No Ye s Is the cable of the rotary encoder securely connected to J300 on the A30 Front Panel board? Replace the rotary encoder . Power Supply module T urn on the PRINCIP AL POWER SWITCH[...]

T roubleshooting 6Ć62 MTG100 & MTG300 MPEG Generator Service Manual Data HDD Install the retaining assemblies on to the SCSI hard drive data cables. Refer to the 040ĆA028Ć00 hardware upgrade kit. Input 3341344803" in the "Enter Password:" dialog box. No Ye s Are the bracket and retaining rod for the data cable connector on [...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć63 Check the scandisk output file (refer to Scandisk Output File on page 6Ć52) . Select the Simple Scan Disk or Normal Scan Disk from the bezel menu. 3 Ye s Are any errors detected? No Perform the Quick Format command or reinstall the firmware, and then download TS files. T o St[...]

T roubleshooting 6Ć64 MTG100 & MTG300 MPEG Generator Service Manual System HDD Connect a keyboard to the KEYBOARD connector on the rear panel. Connect a monitor to the VGA connector on the rear panel or short between pin 2 and 3 of J278 on the A40 MISC (Power Distribution & Interface) board (see Figure 6Ć36) to be able to display the boot[...]

T roubleshooting MTG100 & MTG300 MPEG Generator Service Manual 6Ć65 Solid state disk Connect a monitor to the VGA connector on the rear panel or short between pin 2 and 3 of J278 on the A40 MISC (Power Distribution & Interface) board (see Figure 6Ć36) to be able to display the boot screen on the LCD. Set the boot drive to A:then:C"[...]

T roubleshooting 6Ć66 MTG100 & MTG300 MPEG Generator Service Manual     $ !" #"  "          Figure 6Ć36: Location of the A40 MISC (Power Dis[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć67 Firmware Updates The MPEG generator firmware can be updated when troubleshooting indicates it is needed or when the firmware has been updated. This subsection explains how to update the firmware. Equipment Required T able 6-8 lists the equipment required to update the firmware. T able 6Ć8: Eq[...]

Firmware Updates 6Ć68 MTG100 & MTG300 MPEG Generator Service Manual 7. Double-click the Fw folder in the list. This will display the contents of the folder . 8. Double-click the V ersionup.exe in the list. This will open the MTG Series Firmware Update dialog box shown in Figure 6-37. Figure 6Ć37: MTG Series Firmware Update dialog box 9. In th[...]

Firmware Updates MTG100 & MTG300 MPEG Generator Service Manual 6Ć69  . For version 1.00, the err or message “Internal err or occurr ed:” is displayed on the MPEG generator ’ s scr een. However , this does not mean that the tr ouble is detected during transferring the files. 12. Power off the MPEG generator and then power it o[...]

Firmware Updates 6Ć70 MTG100 & MTG300 MPEG Generator Service Manual 1. Select the System... from the UTILITY pull-down menu, and then press the OK bezel button. This will open the System dialog box shown in Figure 6-41. Figure 6Ć41: System dialog box 2. In the dialog box, check whether the new version of the firmware is properly installed. Ch[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć71 Replacing the Hard Disk Drive(s) When you replace the data hard disk drives (SCSI hard disk drives) or system hard disk drive (IDE hard disk drive) for servicing, you must perform the following tasks:  Data hard disk drives:  Back up the files stored on the data hard disks  Set the ju[...]

Replacing the Hard Disk Drive(s) 6Ć72 MTG100 & MTG300 MPEG Generator Service Manual Data Hard Disk Drives  . Whenever r eplacing the data har d disk drives, be sure to r eplace both of the disk drives at the same time. Before removing the data hard disk drives, you should save all the transport stream, insertion, and preset files ([...]

Replacing the Hard Disk Drive(s) MTG100 & MTG300 MPEG Generator Service Manual 6Ć73 If you use the hard disk drives other than above, set the jumpers to obtain the following configuration:  SCSI ID : 0  T erminator Power Supply : Off  Auto Spin Up : Off  Internal SCSI T erminator : Off  Auto Start Delay : Off After you have inst[...]

Replacing the Hard Disk Drive(s) 6Ć74 MTG100 & MTG300 MPEG Generator Service Manual 3. Using the file transfer command (PC to MTG...) of the MTG Comm + application, download the following one file to /main/usr/insert directory in the MPEG generator:  insert.eit System Hard Disk Drive  . When you r eplace the system har d disk dr[...]

Replacing the Hard Disk Drive(s) MTG100 & MTG300 MPEG Generator Service Manual 6Ć75 After you have installed the system hard disk drive properly , perform the following procedure to format the data hard disks: 1. Select Service... from the Utility pull-down menu of the MPEG generator . This will open the Enter Password: dialog box. 2. In this [...]

Replacing the Hard Disk Drive(s)  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć77 Hardware Device Error Codes This subsection describes the hardware device error codes displayed on the screen during operation. These error codes appear in the dialog box as a error message with the following form: “Internal error occurred : <error code>” The hardware device error co[...]

Hardware Device Error Codes 6Ć78 MTG100 & MTG300 MPEG Generator Service Manual T able 6Ć10: Hardware device error codes Error code Symptom Possible Causes Solution Common with Hard Disk Controller , Change Packet, and Change Word 0xX1XXXX01 The device is not ready . (1) The MPU system of the device Reset the instrument. If this error f 0xX1XX[...]

Hardware Device Error Codes MTG100 & MTG300 MPEG Generator Service Manual 6Ć79 T able 6Ć10: Hardware device error codes (Cont.) Error code Solution Possible Causes Symptom Change Packet 0x25400100 A nonĆtransport stream packet is detected. A nonĆtransport stream packet data was transferred to the input buffer of the Change Packet. Reset the[...]

Hardware Device Error Codes  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 6Ć81 Error Messages T able 6-1 1 lists instrument error messages that appear during operation. These messages are displayed in the pop-up message box. If any of these errors is detected while a transport stream is output, the output is stopped. Press the OK bezel button or ST AR T/STOP button to re[...]

Error Messages 6Ć82 MTG100 & MTG300 MPEG Generator Service Manual T able 6Ć1 1: Error messages (cont.) Error message (  ! "  ( $ " $ ( $ #!' (! " ! " (! #[...]

Error Messages MTG100 & MTG300 MPEG Generator Service Manual 6Ć83 T able 6Ć1 1: Error messages (cont.) Error message Hardware control update failure"; Cannot create SI template"; Cannot load SI template"; PID already exist"; PID not exist"; Cannot reject"; Exceed replace limitation"; [...]

Error Messages  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 7Ć1 Options and Accessories This section describes the various options as well as the standard and optional accessories that are available for the MTG100 and MTG300 MPEG Generator . Options The options available for the MTG100 and MTG300 MPEG Generators are shown in T able 7-1. T able 7Ć1: Options[...]

Options and Accessories 7Ć2 MTG100 & MTG300 MPEG Generator Service Manual Optional Accessories Y ou can also order the optional accessories listed in T able 7-3. T able 7Ć3: Optional accessories Accessory Part number !   ""    ?[...]

MTG100 & MTG300 MPEG Generator Service Manual 8Ć1 Electrical Parts List The modules that make up this instrument are often a combination of mechanical and electrical subparts. Therefore, all replaceable modules are listed in section 10, Mechanical Parts List. Refer to that section for part numbers when using this manual.[...]

Electrical Parts List  MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 9Ć1 Diagrams This section contains the following diagrams:  Block Diagram of the MPEG generator .  Interconnect Diagram of the MPEG generator . Block diagrams show the modules and functional blocks in the MPEG generator . Interconnect diagrams show how the modules in the MPEG generator connec[...]

Diagrams  MTG100 & MTG300 MPEG Generator Service Manual[...]

9-3 MTG100 & MTG300 MPEG Generator Service Manual Main Board A10 PCI Back Plane Data HDD Data HDD ASI OUT SSI OUT EXT 27MHz REF IN ECL CONTROL ECL/TTL/L VDS OUT Interface Board A20 Solid State Disk Card Edge Card Edge Card Edge CPU LAN MISC (Power Distribution & Interface Board) A40 System HDD Fan Fan Power Supply (12 V) Power Supply (5 V) [...]

 MTG100 & MTG300 MPEG Generator Service Manual[...]

9-5 MTG100 & MTG300 MPEG Generator Service Manual J3700 J3702 J4000 W200 W170 J4004 J4002 W160 Main Board A10 PCI Backplane Data HDD Data HDD ASI OUT SSI OUT EXT 27MHz REF IN ECL CONTROL ECL/TTL/L VDS OUT 10 W070 Interface Board A20 Solid State Disk W350 W060 W150 W090 Card Edge Card Edge Card Edge CPU LAN MISC (Power Distribution & Interfa[...]

 MTG100 & MTG300 MPEG Generator Service Manual[...]

MTG100 & MTG300 MPEG Generator Service Manual 10Ć1 Mechanical Parts List This section contains a list of the replaceable modules for the MPEG generator . Use this list to identify and order replacement parts. Parts Ordering Information Replacement parts are available through your local T ektronix field office or representative. Changes to T ek[...]

Mechanical Parts List 10Ć2 MTG100 & MTG300 MPEG Generator Service Manual Modules can be serviced by selecting one of the following three options. Contact your local T ektronix service center or representative for repair assistance. Module Exchange. In some cases you may exchange your module for a reman- ufactured module. These modules cost sig[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć3 The table titled Manufacturers Cross Index shows codes, names, and addresses of manufacturers or vendors of components listed in the parts list. Manufacturers cross index Mfr . code Manufacturer Address City , state, zip code S3109 FELLER 72 VERONICA A VE UNIT 4 SUMMERSET[...]

Mechanical Parts List 10Ć4 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-1-1 390-1202-XX 1 CABINET ,ASSY :MTG100/300,AL 80009 -2 21 1-0945-XX 6 SCREW ,MACHINE:M4X8MM L,S[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć5                     Figure 10Ć1: Cabinet[...]

Mechanical Parts List 10Ć6 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-2-1 200-4562-XX 1 COVER,FRONT :TV GRA Y ,ABS 80009 -2 366-081 1-XX 1 PUSH BUTT ON:SET ,SIL VER G[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć7                     A35 A30  Figure 10Ć2: Front panel unit[...]

Mechanical Parts List 10Ć8 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-3-1 386-7162-XX 1 SUPPORT ,FDD:FRONT LEFT ,AL 80009 -2 21 1-0871-XX 2 SCREW,MACHINE:M3X6MM L,PNH[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć9 Replaceable parts list (Cont.) Fig. & index number Mfr . part number Mfr . code Name & description Qty Serial no. discont'd Serial no. effective T ektronix part number -34 21 1-A152-XX 4 SCREW ,MACHINE:M2.5X8MM L,PNH,STL,NI PL,CROSS REC,W/KOGA TAMARU & LO[...]

Mechanical Parts List 10Ć10 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-4-1 1 19-B084-XX 2 HARD DISK UNIT :18GB,3.5INCH,UL TRA SCSI 80009 -2 386-7230-XX 2 PLA TE:3.5&q[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć1 1                            Figure 10Ć4: Hard disk drives[...]

Mechanical Parts List 10Ć12 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-5-1 671-4905-XX 1 CIRCUIT BD ASSY :A10,MAIN,389-A923-00 WIRED 80009 -2 21 1-0871-XX 16 SCREW ,M[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć13                          [...]

Mechanical Parts List 10Ć14 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-6-1 441-2197-XX 1 CSASSIS ASSY :CPU,AL 80009 -2 343-1651-XX 1 RET AINER,BOARD:CPU 80009 -3 21 1[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć15                     Figure 10Ć6: CPU unit[...]

Mechanical Parts List 10Ć16 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-7-1 1 19-6143-XX 1 POWER SUPPL Y :INPUT 85-264V AC,OUTPUT 5VDC,60A 80009 -2 343-1 182-XX 1 CLAM[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć17             Figure 10Ć7: Power supply unit[...]

Mechanical Parts List 10Ć18 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list Fig. & index number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number 10-8-1 351-0623-XX 1 SLIDE,DWR,EXT :22.0X1.54,STEELSAFETY CONTROLLED 80009 -2 21 1-0945-XX 6 SCREW[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć19                    Figure 10Ć8: Rack mount[...]

Mechanical Parts List 10Ć20 MTG100 & MTG300 MPEG Generator Service Manual Replaceable parts list CompoĆ nent number T ektronix part number Serial no. effective Serial no. discont'd Qty Name & description Mfr . code Mfr . part number CABLE ASSEMBLIES ** W010 196-31 12-XX 1 LEAD,ELECTRICAL:18A WG,6.0L,5-4,W/LUG TERM 80009 W01 1 174-428[...]

Mechanical Parts List MTG100 & MTG300 MPEG Generator Service Manual 10Ć21 Replaceable parts list (Cont.) CompoĆ nent number Mfr . part number Mfr . code Name & description Qty Serial no. discont'd Serial no. effective T ektronix part number ST ANDARD ACCESSORIES 063-3276-XX 1 SOFTWARE PKG:3.5 INCH DISK,DOWNLOADER TK0191 071-0615-XX 1[...]

Mechanical Parts List  MTG100 & MTG300 MPEG Generator Service Manual[...]