Tiger Products Co., Ltd JD 5065 / 5085 - 5105M Bedienungsanleitung

P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SIDE ROT AR Y ASSEMBLIES JD 5065 / 5085 - 5105M 06010020 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 06/27/201 1[...]

T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize [...]

FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . We recommend that yo[...]

[...]

T ABLE OF CONTENTS SAFETY SECTION _____________________________________ 1 ASSEMBL Y / MOUNTING SECTION ______________________ 2 OPERA TION SECTION _________________________________ 3 MAINTENANCE SECTION ______________________________ 4 P ARTS SECTION ______________________________________ 5 COMMON P ARTS SECTION ____________________________ 6 W ARR[...]

[...]

SAFETY SECTION[...]

Side Rtry Safety Section 1-2 SAFETY SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VER Y SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in M[...]

Side Rtry Safety Section 1-3 SAFETY SAFETY ! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) PELIGRO! LEA EL INSTRUCTIVO! DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Message[...]

Side Rtry Safety Section 1-4 SAFETY SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the Tractor while the tractor is moving. Mount the Tractor[...]

Side Rtry Safety Section 1-5 SAFETY SAFETY WARNING! The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment. (SG-16) WARNING! T ransport only at safe speeds. Serious accident s and injuries ca[...]

Side Rtry Safety Section 1-6 SAFETY SAFETY WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good [...]

Side Rtry Safety Section 1-7 SAFETY SAFETY CAUTION! On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5) DANGER! NEVER use drugs or alcohol immediately before or whi[...]

Side Rtry Safety Section 1-8 SAFETY SAFETY DANGER! The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities. To reduce[...]

Side Rtry Safety Section 1-9 SAFETY SAFETY DANGER! Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working[...]

Side Rtry Safety Section 1-10 SAFETY SAFETY WARNING! Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower[...]

Side Rtry Safety Section 1-11 SAFETY SAFETY WARNING! The rotating parts of this machine continue to rotate even after the Tractor has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased. (SBM-5) “Wait a minute...Sav[...]

Side Rtry Safety Section 1-12 SAFETY SAFETY[...]

Side Rtry Safety Section 1-13 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 1 22839 1 INSTRUCT Don Not Lubricate With Automatic Grease Gun 2 22840 1 WARNING Foreign Objects Contacted 3 24028 1 WARNING Inspect Rear Flap 4 31522 1 LOGO TIGER MOWERS 5 31523 3 LOGO TIGER MOWERS 6 42350 1 DANGER Cuttershaft Direction 7 33743 1 INSTRUCT Mowing Safet Tips [...]

Side Rtry Safety Section 1-14 SAFETY SAFETY 10"X5.5" 31522 MOWER DECK 18.25"X10" 31523 HYDRAULIC T ANK 22840 INSIDE OF CAB 22839 MOWER DECK P AR T NO. LOCA TION 24028 MOWER DECK[...]

Side Rtry Safety Section 1-15 SAFETY SAFETY 5 42399 MOWER DECK 42400 MOWER DECK 33743 INSIDE OF CAB 42350 MOWER DECK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-16 SAFETY SAFETY 29-6T3221 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB 6T3219 INSIDE OF CAB 6T3217 MOWER DECK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-17 SAFETY SAFETY 6T3236 MOWER DECK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 INSIDE OF CAB P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-18 SAFETY SAFETY 16 6T3236 MOWER DECK HYDRAULIC T ANK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 HYDRAULIC T ANK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-19 SAFETY SAFETY TB101 1 MOWER DECK 02962764 MOWER DECK DRAFT BEAM 6T3261 MOWER DECK 6T3249A MOWER DECK P ART NO. LOCA TION[...]

Side Rtry Safety Section 1-20 SAFETY SAFETY 02967827 CAB FENDER 02965262 DRAFT BEAM P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-21 SAFETY SAFETY 00756059 MOWER DECK 34852 HYDRAULIC T ANK[...]

Side Rtry Safety Section 1-22 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 Round Manual Canister 33997 1 Decal, Sheet, Manual Canister 2 * Decal 3 * Decal 4 * Decal 5 * AVAIL Specification Product Manual 6 33753 1 EMI Safety Manual 7 34296 1 Front Adhesive Pad 8 34297 1 Rear Adhesive Pad 9 6T1823 4 [...]

Side Rtry Safety Section 1-23 SAFETY SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations U.S[...]

Side Rtry Safety Section 1-24 SAFETY SAFETY[...]

Assembly Section 2-1 ASSEMBL Y SECTION JD5XX5M - TM[...]

ASSEMBL Y Assembly Section 2-2 Before attempting to moun t your T iger mower , it is import ant to read an underst a nd all of the Safety Messages in the Safety section of this manual. Check complete shipment list again st the packing list to make sure there are no shortages. Make ce rtain the tractor model is the appropriate one for the mower rece[...]

ASSEMBL Y Assembly Section 2-3 CRANKSHAFT ACCESS T o access the crankshaf t of the JD506 5M and 5085-105M, a hole will need to be cut in the front of the tractor casting. The battery plate will need to be raised to cut the hole and attach the crankshaf t adapter . T o do this, remove and save the bolts holding the battery pl ate to the tractor fram[...]

ASSEMBL Y Assembly Section 2-4 CRANKSHAFT ACCESS (continued) Find the center punched marking on the fr ont end of the tractor(shown belo w), and use it as a guide for cutting. Use a 1-3/4” ho le saw to cut a hole for the driveshaft. Once the hole is cut you will be able to look thro ugh the hole and see the driveshaf t cover . The driveshaft cove[...]

ASSEMBL Y Assembly Section 2-5 DRIVESHAFT & FRONT PUMP MOUNTING Thread the pump drive shaf t into the crankshaf t adapter . Slide splined drive shaf t coupler onto the pump drive shaf t. Install the pump onto the mounting bracket. NOTE: the pump is of fset to one direction, the pump should be installed with the offset side on top. Inst a ll har[...]

ASSEMBL Y Assembly Section 2-6 CABLE CONTROL LEVER ST AND Place the cable control bracket on the floor so th at the bracket is 2-1/2” from the side edge of the door , and 4-3/8” in front of the re ar edge of the door . See images below . Be sure that the location of the stand will allow the operation of a ll control levers in the tra ctor and t[...]

ASSEMBL Y Assembly Section 2-7 SWITCH BOX WIRING Route the green wires and the red wire (with the 10amp fuse) fro m the switchbox to the front console pan el. Refer to the part s section for wiring diagram to hook up the switch box. Cover the wire s from the sw itch box with plastic wire wrap provided. Remove the console p anel under the steering w[...]

ASSEMBL Y Assembly Section 2-8 WEATHER-PACK/METRI-PACK ASSEMBLY These instructions apply to bo th Weather-Pack and Metri-p ack connectors. NOTE: Use the specific tool for the type of conne ctor you are assembling. (ASM-C-0009)[...]

ASSEMBL Y Assembly Section 2-9 V AL VE MOUNTING Attach the rea r valve mounting bracket to the fender of the tractor by removing the two rear bolts on the left fender and the two rear bolts on the right fender . See illustration below . Drill the square holes in the fenders to accept 3/8” cap screws. Use the hardware noted in the p arts section t[...]

ASSEMBL Y Assembly Section 2-10 PRESSURE LINE INST ALLA TION The hydraulic pressure line will be plum bed into the tractors power beyond port. Locate the power beyond port on the up per right side of the tractor rear remotes, remove the plug (refer to the illu stration below and the Parts Section). Af ter the plug is removed, connect the adapter an[...]

ASSEMBL Y Assembly Section 2-11 MANUAL LIFT V AL VE PORTS (ASM-C-0057) MANUAL SWITCH BOX MOUNTING The switch box is to be secured to the operators side o f the control hand les, or valve stand. Refer to the part s section for assembly and component s needed. (ASM-C-0071)[...]

ASSEMBL Y Assembly Section 2-12 *NOTE ON HUSCO CONTROL V A L VES* Manual, cable controlled (Husco control va lve) boom mowers require check valves with integral restricting orifice (#06502036) in stalled in the control valve wo rk ports that are connected to the gland ends of th e main and secondary boom cylinders. This check valve allows oil to fr[...]

ASSEMBL Y Assembly Section 2-13 HOSE AND WIRE ROUTING Attach two clamps to the right rear wheel we ll for proper hose/wire routing. Drill one hole for each clamp. Use th e lower re ar corner of the wheel well as an origin for measuring. The holes should be 10mm or 3/8” reamed to a ccept 3/8” hardware. Measure along the back edge of the wheel we[...]

ASSEMBL Y Assembly Section 2-14 FENDER CUT FOR WHEEL WELL T ANK A notch will have to be cut into the left rear fender to allow room for the hyd raulic tank filler neck. The notch sho uld start at 2 inches from the rear corner of the fender and create a 1 inch deep arc that is 5 inch es long. T rim lock should be used on the sharp edges.. (ASM-JD-00[...]

ASSEMBL Y Assembly Section 2-15 mast, and to the flail mowers. The hoses may get into the front and/or rear tires if not properly routed and clamped. (ASM-C-0061) FILLING HYDRAULIC RESER VOIR Refer to the maintenance section for f illing specifications and hydraulic oil[...]

ASSEMBL Y Assembly Section 2-16 requirements. (ASM-C-0004hydro resrv) WHEEL SP ACER WITH WHEEL WELL T ANK When the left wheel is off, a sp acer kit is needed with the wheel well t ank (part# 06200637.) Atta ch the spacer to the lef t wheel portion of the axle with the hardware provided. When you are ready to re-attac h the lef t wheel, the wheel go[...]

ASSEMBL Y Assembly Section 2-17 GENERAL HOSE INST ALLA TION Refer to the part s section for det ailed information about hoses and fittings for this application. (ASM-C-0 01 1) HOSE COVERING Secure hoses together with zip ties whereve r loose. Wrap the hoses b etween the swivel and main boom with the hose cover pr ovid ed. Wrap the hoses between th [...]

ASSEMBL Y Assembly Section 2-18 chart located in the mainten ance section of this manual. (ASM-JD-0072) . SIDE MOWER HYDRAULIC DIAGRAM (ASM-C-0090)[...]

ASSEMBL Y Assembly Section 2-19 CONTINUOUS DUTY SOLENOID SWITCH Mount the solenoid switch, drill holes to match if necessary , mount in dry an d well protected area. Secure as shown in the p arts section. A.) ORANGE 10 GA. wire from terminal (D) to +12V battery post on tractor st arter solenoid. B.) RED 14 GA. wire from terminal (C) to tractor plug[...]

ASSEMBL Y Assembly Section 2-20 CONTINUOUS DUTY SOLENOID SWITCH (MOUNTING) (ASM-JD-0096)[...]

ASSEMBL Y Assembly Section 2-21 DRAFT BEAM INST ALLA TION Install ½” O-ring breather into butt port of inboard cylinder . Install fittings in the rod end of the cylinder according to the dia gram in the Common Part s section. These fittings should be positioned to face the butt end of the cylinder . Next turn the clevis onto the rod of th e cy l[...]

ASSEMBL Y Assembly Section 2-22 MOWER MOUNTING Check that all grease zerks have been inst alled in the draft beams pivot arm, lef t linkage arm, right linkage arm, a nd cylinder mounting ears. Using a clevis pin and roll pins, connect the pivot arm to clevis on draft beam. NOTE: Make sure the longer dist ance between the cutout and the end of the p[...]

ASSEMBL Y Assembly Section 2-23 TRA VEL LOCK MOUNTING Install the travel lock bracket wit h pin and clip on the draf t beam. Slide the draf t beam and align the travel lock bracket hole with t he mounting hole on the main frame. Inst all the capscrew , lockwasher and hex nut as shown in the picture. Raise the deck/flail to it’s upright p osition [...]

ASSEMBL Y Assembly Section 2-24 ST OP BOL T ADJUSTMENT Extend the outboard cylinder all th e way out. Adjust the stop adjustment bolt (located on the top of the draft beam) out until it is up against the bonnet. Lock the bolt down with the ¾” hex nut. NOTE: When the outboard cylinder is f u lly extended, the bonnet or deck should either be up ag[...]

ASSEMBL Y Assembly Section 2-25 FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation d ecals on the steering column and side counsel where they are clearly visible to the oper ator . These decals should be understood by each operator of the machine in conjunction with th e safety and operation section of this book. The decals are[...]

ASSEMBL Y Assembly Section 2-26[...]

Operation Section 3-1 © 201 1 Alamo Group Inc. OPERA TION SECTION[...]

OPERATION SIDE ROTARY Operation Section 3-2 © 201 1 Alamo Group Inc. OPERA TION TIGER SIDE ROT AR Y MOWER OPERA TING INSTRUCTIONS T iger Side Rotary Mowers are manufactured with quality material by skilled workers. The side mow er positions may optionally be controlled with the tractors remote hy draulic connections or a combination of lift valve [...]

OPERATION SIDE ROTARY Operation Section 3-3 © 201 1 Alamo Group Inc. OPERA TION 1. ST ANDARD EQUIPMENT AND SPECIFICA TIONS SIDE ROT AR Y Cutting Width 60” and 72” Actual Cut S pindle Drive Direct S pline and Direct Flexible Coupler Cutter Assembly One-piece form ed d ish type w ith one-piec e forged spindle asse mbly Cutter Head Arc 180° on C[...]

OPERATION SIDE ROTARY Operation Section 3-4 © 201 1 Alamo Group Inc. OPERA TION 2. OPERA TOR REQUIREMENTS Safe operation of the unit is the re sponsibility of a qualified ope rator . A qualified o perator has read and underst ands the implement and tractor Operator’s Manua ls and is experienced in imple ment and tractor operation and all associa[...]

OPERATION SIDE ROTARY Operation Section 3-5 © 201 1 Alamo Group Inc. OPERA TION 3. TRACT OR REQUIREMENTS In addition to tractor horsepowe r and size required to operate th e boom unit, the tractor must also be pro perly equipped to provide operator protection, to alert approac hing vehicle drivers of t he tractor’s presence, and to ensure tracto[...]

OPERATION SIDE ROTARY Operation Section 3-6 © 201 1 Alamo Group Inc. OPERA TION 3.4 Front End Weight A minimum of 20% tot al tractor weight must be maint ained on the tractor front end at all times. Front end weight is critical to maintain steering contro l and to prevent the tractor from rea ring up while driving. If the front end is too light, a[...]

OPERATION SIDE ROTARY Operation Section 3-7 © 201 1 Alamo Group Inc. OPERA TION 4.2 Dismounting the T ractor Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake, idle the engine down and lower the im plement to the ground. Shut down the tractor engine according to the operator’s manual, remov[...]

OPERATION SIDE ROTARY Operation Section 3-8 © 201 1 Alamo Group Inc. OPERA TION Never run the T ractor engine in a closed building or witho ut adequate ventilation. The exhaust fumes can be hazardou s to your health. (SG-23) S tart tractor only when properly seated in the Tractor seat. S tarting a tractor in gear can result in injury or d eath. Re[...]

OPERATION SIDE ROTARY Operation Section 3-9 © 201 1 Alamo Group Inc. OPERA TION Do not operate this Equipment with hydr aulic oil o r fuel leaking. Oil and fuel are explosive a nd their presence could presen t a hazard. Do not check for leaks with your hand! High-pressure oil stre ams from breaks in the line could pe netrate the skin and cause tis[...]

OPERATION SIDE ROTARY Operation Section 3-10 © 201 1 Alamo Group Inc. OPERA TION 7.1 T ractor Pre-Operation Inspection/Service Refer to the tractor op erator ’s man ual to ensure a complete pre-operation inspection and scheduled service is performed accord ing to the manufacturers recommendations. The following are some of the items that require[...]

OPERATION SIDE ROTARY Operation Section 3-11 © 201 1 Alamo Group Inc. OPERA TION NOTE: The mower Op erator’s Manual and affixed Decals cont ain import ant instr uctions on the safe and proper use of the mower . Maintain these import ant safety features on the mower in good condition to ensure the information is available to the operator at all t[...]

OPERATION SIDE ROTARY Operation Section 3-12 © 201 1 Alamo Group Inc. OPERA TION HYDRAULIC LINE INSPECTION • Check for hydraulic leaks a long hoses, cylinders and fittings. IMPORT ANT : DO NOT use your hands to check for oil leaks. Use a piece of heavy p aper or cardboard to check for hydraulic oil le aks. • Inspect the condition of the valve [...]

OPERATION SIDE ROTARY Operation Section 3-13 © 201 1 Alamo Group Inc. OPERA TION HYDRAULIC PUMP/OIL RESERVOIR • Check oil rese rvoir level and oil cond ition. (Add specific type oil if low) • Change hydraulic oil filter a nd hydraulic oil according to mainte nance schedule. • Ensure there a re no oil leaks and fitting are properly connected [...]

OPERATION SIDE ROTARY Operation Section 3-14 © 201 1 Alamo Group Inc. OPERA TION ROT AR Y HEAD INSPECTION • Inspect blades and bl ad e bolts for looseness and excessive wear . Rotate to 90° to make for checking easier . Replace damage d, worn, and missing blades as complete set s to maintain rot ary balance. • Ensure blade carrier nut s are t[...]

OPERATION SIDE ROTARY Operation Section 3-15 © 201 1 Alamo Group Inc. OPERA TION 7.2 Cutting Component Inspection Inspect blade p an and blade assembly for the following: OPS-U-0031 Inspect the Blades daily for abnormal wear . REPLACE BOTH BLADES on that carrier IMMEDIA TEL Y if either blade has: • Become bent or deformed from it’ s original s[...]

OPERATION SIDE ROTARY Operation Section 3-16 © 201 1 Alamo Group Inc. OPERA TION 7.3 Blade Bolt Inspection Inspect Blade Bolt Head da ily for wear as followed: Inspect the Blade Bolt Heads d aily for abn ormal wear . REPLACE BOTH BLADE BOL TS on the Blades IMMEDIA TEL Y if either blade bolt s has: • Visible cracks or • If the reces sed area on[...]

OPERATION SIDE ROTARY Operation Section 3-17 © 201 1 Alamo Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conduc ting the inspec tion, make sure th e tractor engine is off, all rot ation has stopped and the trac tor is in p ark wi[...]

OPERATION SIDE ROTARY Operation Section 3-18 © 201 1 Alamo Group Inc. OPERA TION Side Rotary Mower PRE-OPERA TION Inspection Mower ID#________________ Make ____________________ Date: ________________ Shift ____________________ Before conduct ing the inspection, ma ke sure the tractor engine is off, all rot ation has stopped and the tractor is in p[...]

OPERATION SIDE ROTARY Operation Section 3-19 © 201 1 Alamo Group Inc. OPERA TION DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to t ake while driving with an att ached implem ent. Ensure the tractor has the ca p acity to handle the weight of t[...]

OPERATION SIDE ROTARY Operation Section 3-20 © 201 1 Alamo Group Inc. OPERA TION 7.4 St arting the T ractor The procedure to st art the tractor is model specific. Refer to the tractor operator ’s manual for starting procedures for your particular tractor . Consult an authorized dealer if the st arting procedure is unclear . Ensure the 3-point co[...]

OPERATION SIDE ROTARY Operation Section 3-21 © 201 1 Alamo Group Inc. OPERA TION 7.7 7.6 Driving the T ract or and Implement S tart off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and unit. Moving slowly at fi rst will also prevent the tractor from rearing up and loss of steering cont[...]

OPERATION SIDE ROTARY Operation Section 3-22 © 201 1 Alamo Group Inc. OPERA TION Inclines and ditches should be approached along a line which is at an angle as shown. This type of path will reduce the possibility of resulting damage. If the gradient is so ste ep that su ch an approach increases the possibility of a tractor roll-over , select an al[...]

OPERATION SIDE ROTARY Operation Section 3-23 © 201 1 Alamo Group Inc. OPERA TION Many varied objects , such as wire, cable, rope, or chains, can become ent angled in the operating part s of the mower head. These items could then swing outside the housing at greater velocities than the blad es. Such a situation is extremely hazard ous and could res[...]

OPERATION SIDE ROTARY Operation Section 3-24 © 201 1 Alamo Group Inc. OPERA TION Rotary Mowers ar e capable under adver se conditions of throwing objects for great distance s (300 feet or more) and ca using serious injury or death. Follow safety messag es carefully . STOP MOWING IF P ASSERSBY ARE WITHIN 300 Feet UNLESS: -Front and Rear Deflector s[...]

OPERATION SIDE ROTARY Operation Section 3-25 © 201 1 Alamo Group Inc. OPERA TION 9. Operating the Contro l V alves - Side Mount POSITION CONTROL V AL VE - Th e V a lve is located to the right of the operator at a convenient height o n a non-cab unit. The V alve is located behind the rear windo w in a cab tractor . The V alve operation plate is loc[...]

OPERATION SIDE ROTARY Operation Section 3-26 © 201 1 Alamo Group Inc. OPERA TION MOWER LIFT The handle nearest the ce nter of the tracto r , actuates the Lift Cylinder (Inboard). Pulling the valve handle back, towards th e operator , causes the Lift Cylinder to raise the Extension Arm. If the handle is released, the valve wi ll automatically retur[...]

OPERATION SIDE ROTARY Operation Section 3-27 © 201 1 Alamo Group Inc. OPERA TION MEASUREMENT OF HEAD PITCH 1. CUT MOWE R OFF AND ALLOW BLADES TO ST OP ROT A TING 2. Move machine to a flat, level area such as a concrete slab 3. Lower mower head to within several inches of th e ground but do not rest head on ground . 4. S top engine. 5. Position bla[...]

OPERATION SIDE ROTARY Operation Section 3-28 © 201 1 Alamo Group Inc. OPERA TION 9.1 Basic T roubleshooting Gu ide for First St art-up. a. Electrical solenoid valve does no t work - check wiring, possible faul ty switch, possible faulty solenoid. b. Pump is making noise - check for obstr uction in suct ion hose and ta nk suction assembly , check a[...]

OPERATION SIDE ROTARY Operation Section 3-29 © 201 1 Alamo Group Inc. OPERA TION 9.2 Control Location and Functions The side mower height is controlled with a two or thr ee spool valve and is coordinated as shown below . The optional three spool valve allows for the operation of a re ar rotary mower or side ditcher . If the unit is equippe d with [...]

OPERATION SIDE ROTARY Operation Section 3-30 © 201 1 Alamo Group Inc. OPERA TION 9.3 Operating the Mower Only operate the mower from th e tr acto r oper ator’s seat with the se atbelt securely f astened. The tractor must be equipped with a ROPS in the raised position or a ROPS cab. The mower is designed to cut vegetation up to 2” in di ameter [...]

OPERATION SIDE ROTARY Operation Section 3-31 © 201 1 Alamo Group Inc. OPERA TION When rota ting part s are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow bystanders within 300 feet of the machine when in operation. Extreme care should be taken when operating near loose objects - such as gravel, [...]

OPERATION SIDE ROTARY Operation Section 3-32 © 201 1 Alamo Group Inc. OPERA TION When encountering a very severe condition which causes the tractor to stall, disengage mower , start tractor , raise the mower from the cut. Shut tractor off and inspect the mo wer , blades an d disk for damage before engaging mower again. If the blades jam or stop, d[...]

OPERATION SIDE ROTARY Operation Section 3-33 © 201 1 Alamo Group Inc. OPERA TION All Safety Shields, Guards and Safety devices including (but not limited to) - the Deflectors, Chain Guards, S teel Guards, Gearbox Shields, PTO integral shields, an d Retractable Door Shields should be used and maintained in good working condition. All safety devices[...]

OPERATION SIDE ROTARY Operation Section 3-34 © 201 1 Alamo Group Inc. OPERA TION Never stand or allow another person to stand between a running tractor and the mower when disconnecting the impleme nt from the tractor . 9.4 Shutting Down the Implement T o shut down attached mower head, first brin g the tractor to a complete stop. Decrease engine RP[...]

OPERATION SIDE ROTARY Operation Section 3-35 © 201 1 Alamo Group Inc. OPERA TION Always shut the T ractor completely down, place the transmission in park, and set the parking brake before yo u or anyone else attempts to connect or disconnect the Implement. (SRM-20) 1 1. MOWER ST ORAGE It is recommended that the m ower be stored with the mower full[...]

OPERATION SIDE ROTARY Operation Section 3-36 © 201 1 Alamo Group Inc. OPERA TION 12.1 T ransporting Mower TRANSPORTING UNDER THE UNIT’S OWN POWER When transportin g between job sites or between cutting passes, the following procedure should be followe d: 1. Shut off the power to the cutting he ad ( s) an d allo w all motio n to com e to a co mp [...]

OPERATION SIDE ROTARY Operation Section 3-37 © 201 1 Alamo Group Inc. OPERA TION Next, cap or plug the hose en ds and the ports on the solenoid valve and motor . For a cable lift mower disconnect the lif t cable from the head and secure the lo ose end ba ck on to t he ca b le with th e ca ble cle vis . For a combo lift mower , d isconnect the link[...]

OPERATION SIDE ROTARY Operation Section 3-38 © 201 1 Alamo Group Inc. OPERA TION The SMV (Slow-Moving V ehic le) emblem is universal symbol used to alert drivers of the presence of equipmen t traveling on roadways at a slow speed. SMV signs are a triangular bright orange with reflective red trim for both easy day and night visibility . Make sure t[...]

OPERATION SIDE ROTARY Operation Section 3-39 © 201 1 Alamo Group Inc. OPERA TION Make certain that the “Slow Moving V ehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the T r acto r flashing warning lights and follow all local traf fic regulations. (SG-6 ) Reduce speed befo[...]

OPERATION SIDE ROTARY Operation Section 3-40 © 201 1 Alamo Group Inc. OPERA TION Use adequately sized and rated tr ailers and equipment to transport the tractor a nd implement. Consult an authorized dealer to determin e the proper equipment required. Using adequately sized chains, heavy duty straps , cables and/or binders, securely tie down both t[...]

OPERATION SIDE ROTARY Operation Section 3-41 © 201 1 Alamo Group Inc. OPERA TION 13. TROUBLESHOOTING GUIDE HYDRAULIC CYLINDER NOT WOR KIN G - Check level of hydraulic fluid (see sight gauge on t ank). Check to see if pump is functioning properly by attempting to use a nother cylinder or pressure gauge. If p ump is working properly , check the pres[...]

OPERATION SIDE ROTARY Operation Section 3-42 © 201 1 Alamo Group Inc. OPERA TION[...]

Maintenanc e Sec tio n 4- 1 © 201 1 Alamo Group Inc. MAINTENANCE SECTION[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 2 © 201 1 Alamo Group Inc. MAINTENANCE GENERAL INSTRUCTIONS T iger Mowers are designed for high pe rformance and rugged durability , ye t with simplified maintenance. The purpose of this section of the manual is to help the operator in the reg ular serv icing of the mo wer . Regular maintenance at [...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 3 © 201 1 Alamo Group Inc. MAINTENANCE Do not modify or alter this Implement. Do not permit anyo ne to modify or alter th is Implement, any of its compon ents or any Imp lement func tion. (SG-8 ) Relieve hydraulic pressur e pr ior to doin g an y mainten ance or rep air work on the Implement. Place [...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 4 © 201 1 Alamo Group Inc. MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be do ne are based on ho urs o f oper ation . Use th e tractors h our meter to determine when reg ular servicing is required. Daily or Every 8 Hours ITEM SERVICE COMMENTS Drive Shaft Y oke, U-[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 5 © 201 1 Alamo Group Inc. MAINTENANCE WEEKL Y OR EVER Y 40 HOURS ITEM SERVICE COMMENTS Rotary S pindle Lubricate Every 40 hours or weekly WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hydraulic Fluid Change Change af ter first 50 hours only Filter (10 micron filter) then every 500 hour[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 6 © 201 1 Alamo Group Inc. MAINTENANCE YEARL Y OR EVER Y 500 HOURS ITEM SERVICE COMMENTS S pindle Grease Change Motor to S pindle S pline Change Hydraulic T ank Fluid Change In T ank Hydraulic Fluid Filter Change (10 micron filter ) In-Line HP Filter Change or Change when indicated (10 micron filte[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 7 © 201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING SYMPTOMS CAUSE REMEDY Vibration Loose Bolts Check all bolts and tighten to recommended torq ue spec ifications in this section Cutter assembly a. Check for damaged b lades, disc, unbalance d or cutter shaft. b. Replace if needed. c. Check for w[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 8 © 201 1 Alamo Group Inc. MAINTENANCE TROUBLESHOOTING (CONTINUED) b. Remove the four bolt s holding the small block to the main block. Lift and remove small block bei ng careful no t to damage O - rings/filter . c. Clean filter and re-install. d. Remove large nut on side o f large valve block. Rem[...]

MAINTENANCE SIDE ROTARY Mainte nance Sec tio n 4- 9 © 201 1 Alamo Group Inc. MAINTENANCE T ORQUE SPECIFICA TIONS[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-10 © 201 1 Alamo Group Inc. MAINTENANCE LUBRICA TION RECOMMENDA TIONS DESCRIPTION APPLICA TION GENERAL SPECIFICA TION RECOMMENDED MOBIL LUBRIC ANT T ractor Hydraulics Reservo ir JD-20C Mobilfluid® 424 MF M1 135, M1 141 FNHM2C134D (FNH201) Mower Hydraulics Reservoir Cold T emperatures 0° F S tart-Up [...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-11 © 201 1 Alamo Group Inc. MAINTENANCE POL Y CARBONA TE CARE & MAINTENANCE The propriet ary UV and Abrasion Resist ant surf ace coating on SHIELDS SUPERCOA TED polycar bonate significantly improves performa nce. Periodic cleaning using proper proc edures and comp atible cleaners are recommended t[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-12 © 201 1 Alamo Group Inc. MAINTENANCE RECOMMENDED FILLING INSTR UCTIONS FOR HYDRAULIC RESER VOIRS When filling or checking the oil level, the unit should be park ed on a level surface., shut “OFF” , and allow suf ficient time to cool to ambient temperature. Use caution when removing th e pressur[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-13 © 201 1 Alamo Group Inc. MAINTENANCE REPLACING HIGH PR ESSURE HYDRAULIC FIL TER ELEMENT Assure system has been shut down and depressurized. Locate High Pressure Filte r housing. Conf irm that the elem ent that is about to be installed matches the element p/ n on the filter model t ag. Example: V3.0[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-14 © 201 1 Alamo Group Inc. MAINTENANCE GREASING THE UPPER AND LOWER SHEA VES Locate the grease zerks on the ends of th e upper and lower sheave p ins as shown below . Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into each pin un til it protrude s from the [...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-15 © 201 1 Alamo Group Inc. MAINTENANCE GREASING INNER AN D OUTER DRAFT BE AM PIVOT POINTS Locate the grease ze rks on the inne r and outer dr aft beam pivot bosses. Inje ct Lithium-Complex Extreme Pressure grease confor ming to NLGI2-ISO 320 specifica tions into ea ch zerk u ntil grease protrudes fro[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-16 © 201 1 Alamo Group Inc. MAINTENANCE DRIVE SHAFT YOKE, U-JOINT & STUB SHAFT With engine stopped, inject Lith ium-Complex extr eme pressure gr ease conforming to NLGI2-ISO 32 0 specifications into universal joints a nd slip yoke until grease appears at the seal. Grease them daily or every 8 hour[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-17 © 201 1 Alamo Group Inc. MAINTENANCE BALL V AL VES The ball valves at the hydraulic reservoi r may need to be closed during cert ain maintenance or repa ir procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with va lve) WHEN TRACTOR IS RE-ST ARTED OR WHEN THE PUMP IS COUPLED TO MOT OR OR [...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-18 © 201 1 Alamo Group Inc. MAINTENANCE GREASING MOTOR SPLINE T O SPINDLE SPLINE For direct drive mo wers, locate motor spline and spin dle spline on the mower deck. Grease splines with Mobil moly 52. Use about 4 ounces of grease. Change grease yearly or every 500 hours.[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-19 © 201 1 Alamo Group Inc. MAINTENANCE Blades Check the Blades for cracks and w ear and Blade Bolts for tightness, daily . Blades should be replaced when they are worn excessively , bent, deformed, or out of balance. Blades should always be replac ed in pairs. Bl ade s of different weight s can cause[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-20 © 201 1 Alamo Group Inc. MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1. Be sure you have a complete matchi ng set of new knives for replacement. 2. Remove knives and inspect ho les for dama ge. Also wa tch for crac ks in the di sk around the holes. 3. Lube threads with anti-seize, m otor oil or grease. [...]

HEA VY DUTY SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT A press MUST be used to insta ll bearing cups, bearing con es, and seals. DO NOT use a hammer to inst all races, bearings, or seal s. The part s of assembly may be damaged. NOTE: The grease zerk and gusset s are located on th e top side of the spindle hou sing. Be sure the spindle [...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-22 © 201 1 Alamo Group Inc. MAINTENANCE BEARING INST ALLA TION 1. Press upper bearin g cup into the spindle housing 2. T urn the spindle housing over and press in the lower bearing cup. 3. Place the lower bearin g cone in the b earing cup. Next press the seal in to the spindle housing. The in ner lip [...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-23 © 201 1 Alamo Group Inc. MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be perform ed daily or every 8 hours of service, following the detaile d maintenance instructions in th e operators manual. _______ Pump Drive Shaft: Check for end play in drivesha ft / coupler and lubric[...]

MAINTENANCE SIDE ROTARY Mainte nance Section 4-24 © 201 1 Alamo Group Inc. MAINTENANCE[...]

P ARTS SECTION J D 5 XX5M - TM/ TS R[...]

NOTES[...]

PART NAME INDEX PARTS ORDERING GUIDE ......................................................................................................................................................................... 4 NOTES .......................................................................................................................................[...]

PARTS ORDERING GUIDE ©2011 Alamo Group Inc. Parts Section 5-4 JD5XX5 TM,TSR[...]

NOTES ©2011 Alamo Group Inc. Parts Section 5-5 JD5XX5 TM,TSR[...]

TRACTOR MOUNT KIT ©2011 Alamo Group Inc. Parts Section 5-6 JD5XX5 TM,TSR[...]

TRACTOR MOUNT KIT Continued... ITEM PART NO. QTY. DESCRIPTION 1 06300109 1 MAIN FRAME --- 06300124 1 MNFRM,LDR (LOADER MOUNT) 2 06410898 1 UPRIGHT,LH 3 06410899 1 UPRIGHT,RH 4 06300111 1 AXLE BRC,LH 5 06300110 1 AXLE BRC,RH 6 06380015 1 TANK,RES,WHEEL WELL 7 23152 1 PUMP,P350-1-3/4 GEAR 8 06401034 1 MOUNT,PUMP 9 06380031 1 GUARD,PUMP 10 21639 2 CAP[...]

TRACTOR MOUNT KIT - HYDRAULICS ITEM PART NO. QTY. DESCRIPTION 1 23152 1 PUMP 2 06370109 1 COUPLER 3 06420118 1 DRV SHFT,23.75" (JD5095 - 5105M TRACTORS) 4 LVB24989 1 JD PULLEY KIT (JD5095 - 5105M TRACTORS) 5 06530002 4 CAPSCREW,SKT HD,10MM X 75MM,1.5P 6 06420119 1 DRV SHFT,24.65" (JD5065 - 5085M TRACTORS) 7 06420120 1 ADPTR,CRNKSHFT (JD50[...]

TRACTOR MOUNT KIT - HYDRAULICS Continued... ITEM PART NO. QTY. DESCRIPTION --- 06700091 1 TANK,RES,ASSY,WHEEL WELL 9 06380015 1 TANK,RES,WHEEL WELL 10 06505067 1 SIGHT GAUGE 11 06505044 1 FLTR ASSY,IN-TANK CPLT,SAE10MP 12 21627 4 NYLOCK NUT,3/8",NC 13 06505127 1 PLUG,SAE,#20 14 6T0649 1 FILTER GAUGE 15 TF4888 1 STREET ELBOW,1/8" X 90º 16[...]

2 SPOOL CABLE CONTROL STAND ©2011 Alamo Group Inc. Parts Section 5-10 JD5XX5 TM,TSR[...]

2 SPOOL CABLE CONTROL STAND Continued... ITEM PART NO. QTY. DESCRIPTION 1 31923 1 BRKT,CTRL,CBL 2 6T1251 2 CBL CTRL BOX,180 DEG 3 06510102 1 SWITCH BOX,SIDE 4 34496 1 BRKT,SWITCH BOX 5 6T3951 2 SCREW,MACHINE,8-32 X 1/2" 6 21986 3 LOCKWASHER,1/4" 7 21525 3 HEX NUT,1/4",NC 8 21542 2 CAPSCREW,1/4" X 4",NC 9 21635 3 CAPSCREW,3/[...]

CABLE (MANUAL) LIFT VALVE - 2 SPOOL ©2011 Alamo Group Inc. Parts Section 5-12 JD5XX5 TM,TSR[...]

CABLE (MANUAL) LIFT VALVE - 2 SPOOL Continued... ITEM PART NO. QTY. DESCRIPTION 1 06502058 1 VALVE,2SP,OC (COMBO LIFT DRAFT BEAM) --- 24500 1 VALVE,2SP,OC (CABLE LIFT DRAFT BEAM) 2 06340033 1 VALVE MNT 3 34622 1 PLATE,VALVE,REAR MNT 4 21632 9 CAPSCREW,3/8" X 1-1/2",NC 5 6T2615 4 WASHER,FENDER,3/8" 6 21627 13 NYLOCK NUT,3/8",NC 7[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502058 ©2011 Alamo Group Inc. Parts Section 5-14 JD5XX5 TM,TSR[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502058 Continued... ITEM PART NO. QTY. DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1701 1 END COVER,OPEN CENTER 3 TB1017P 1 VALVE SECTION (SINGLE ACTING,SPRING DETENT) 4 06502091 1 VALVE SECTION (DOUBLE ACTING,CENTER SPRING) 5 N/A - N/A 6 31861 1 RELIEF VALVE, 360 PSI 7 TB1017E 1 RELIEF VALVE, 2250 PSI 8 TB10[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 24500 ©2011 Alamo Group Inc. Parts Section 5-16 JD5XX5 TM,TSR[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 24500 Continued... ITEM PART NO. QTY. DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1701 1 END COVER,OPEN CENTER 3 TB1017P 1 VALVE SECTION (SINGLE ACTING,SPRING DETENT) 4 TB1017P 1 VALVE SECTION (SINGLE ACTING,SPRING DETENT) 5 N/A - N/A 6 N/A - N/A 7 TB1017E 1 RELIEF VALVE, 2250 PSI 8 TB1017M 1 SHUT-OFF PLUG 9 TB[...]

WHEEL SPACER ITEM PART NO. QTY. DESCRIPTION 1 06770025 1 KIT,SPCR,WHL,JD 2 06400919 2 RING,SPACER,WHEEL,JD ©2011 Alamo Group Inc. Parts Section 5-18 JD5XX5 TM,TSR[...]

HOSE GUIDE ON HD DRAFT BEAM ITEM PART NO. QTY. DESCRIPTION 1 28955D 1 HD COMBO DRAFT BEAM 2 21627 2 NYLOCK NUT,3/8",NC 3 06370164 1 HOSE GUIDE 4 21632 2 CAPSCREW,3/8" X 1-1/2",NC ©2011 Alamo Group Inc. Parts Section 5-19 JD5XX5 TM,TSR[...]

NOTES 1 ©2011 Alamo Group Inc. Parts Section 5-20 JD5XX5 TM,TSR[...]

P ARTS SECTION COMMON SIDE ROTARY[...]

NOTES[...]

PART NAME INDEX PARTS ORDERING GUIDE ......................................................................................................................................................................... 5 CABLE DRAFT BEAM ASSEMBLY ...................................................................................................................[...]

PART NAME INDEX FIRE SUPRESSION SYSTEM ELECTRICAL SCHEMATIC .................................................................................................................. 68 WETCUT......................................................................................................................................................................[...]

PARTS ORDERING GUIDE ©2011 Alamo Group Inc. Parts Section 6-5 COMMON SIDE ROTARY[...]

CABLE DRAFT BEAM ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-6 COMMON SIDE ROTARY[...]

CABLE DRAFT BEAM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 6T0105 - DRAFT BEAM (STD WITH TRAVEL LOCK) ------- 27241 - DRAFT BEAM (EXTENDED 6”) 2 6T0150 1 CYLINDER 3” X 18” 3 6T0151R 1 HYD. CYLINDER 3” X 10” 4 6T0100 1 LOWER SHEAVE BRACKET 5 6T0101 1 UPPER SHEAVE BRACKET 6 33768 2 SHEAVE 7 6T0110 1 LIFT CABLE (STD 1/2” X 87 [...]

COMBO DRAFT BEAM ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-8 COMMON SIDE ROTARY[...]

COMBO DRAFT BEAM ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06350001 1 COMBO DRAFT BEAM - STD DTY ROTARY --- 31063 - COMBO DRAFT BEAM - HVY DTY ROTARY 2 6T0151R 1 HYD. CYLINDER 3” X 10” 3 32215 1 HYD. CYLINDER 3” X 12” - STD DTY --- 25343 - HYD. CYLINDER 3" X 12" - HVY DTY 4 TF4500A 1 PIVOT ARM 5 TF4507B 1 RIGHT LINKAG[...]

60IN SIDE CABLE TM ROTARY MOWER ©2011 Alamo Group Inc. Parts Section 6-10 COMMON SIDE ROTARY[...]

60IN SIDE CABLE TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 1 32099 1 RTRY, 60" DECK, CABLE 2 31773 1 GAURD,CHAIN,FRONT,SR60 3 6T1001 1 BRKT, MOTOR MTG, 60"SIDE RTRY 4 6T0820H 2 SKID SHOE, TM60 5 22592 1 FLAP, DEFLECTOR, TM60 6 6T0823 1 BAR, FLAP, TM60 7 6T1024H5 1 SPINDLE ASSY,CPLT,HD,5/8" HOLES 8 21223 1 SPROCKET, 1[...]

72IN SIDE CABLE TM ROTARY MOWER ©2011 Alamo Group Inc. Parts Section 6-12 COMMON SIDE ROTARY[...]

72IN SIDE CABLE TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 1 21225B 1 RTRY,72" DECK, CABLE 2 31931 1 GAURD,CHAIN,FRONT,SR72 3 6T1001 1 BRKT, MOTOR MTG, 60"SIDE RTRY 4 21248 2 SKID SHOE, TM72 5 21295B 1 FLAP, DEFLECTOR, TM72 6 21242A 1 BAR, FLAP, TM72 7 6T1024H5 1 SPINDLE ASSY,CPLT,HD,5/8" HOLES 8 21223 1 SPROCKET, 1-[...]

60IN SIDE COMBO TM ROTARY MOWER ©2011 Alamo Group Inc. Parts Section 6-14 COMMON SIDE ROTARY[...]

60IN SIDE COMBO TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 1 30087D 1 RTRY, 60" DECK, COMBO - STD DUTY --- 32617 1 RTRY, 60” DECK, COMBO - HEAVY DUTY 2 31773 1 GUARD,CHAIN,FRONT,SR60 3 6T1001 1 BRKT, MOTOR MTG, 60"SIDE RTRY 4 6T0820H 2 SKID SHOE, TM60 5 22592 1 FLAP, DEFLECTOR, TM60 6 6T0823 1 BAR, FLAP, TM60 7 6T1024H5[...]

72IN SIDE COMBO TM ROTARY MOWER ©2011 Alamo Group Inc. Parts Section 6-16 COMMON SIDE ROTARY[...]

72IN SIDE COMBO TM ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 1 34260 1 RTRY, 72" DECK, COMBO - STD DUTY --- 31408A 1 RTRY, 72” DECK, COMBO - HEAVY DUTY 2 31931 1 GUARD,CHAIN,FRONT,SR72 3 6T1001 1 BRKT, MOTOR MTG, 60"SIDE RTRY 4 21248 2 SKID SHOE, TM72 5 21295B 1 FLAP, DEFLECTOR, TM72 6 21242A 1 BAR, FLAP, TM72 7 6T1024H5 [...]

60IN SIDE TM CHAIN GUARDS ©2011 Alamo Group Inc. Parts Section 6-18 COMMON SIDE ROTARY[...]

60IN SIDE TM CHAIN GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION --- 31773 - GUARD,CHAIN,TM60,FRONT,ASSY 1 31762 1 GUARD,CHAIN,TM60,FRONT 2 28407 12 CABLE,5/16",BULK (QTY IN FEET) 3 22993 77 CHAIN,5/16",GR30,9 LINK 4 28408 4 U-BOLT,CABLE,5/16" (NOT SHOWN) --- 31774 - GUARD,CHAIN,TM60,REAR,ASSY 5 31763 1 GUARD,CHAIN,TM60,REAR 6 3[...]

72IN SIDE TM CHAIN GUARDS ©2011 Alamo Group Inc. Parts Section 6-20 COMMON SIDE ROTARY[...]

72IN SIDE TM CHAIN GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION --- 31931 - GUARD,CHAIN,TM72,FRONT,ASSY 1 31863 1 GUARD,CHAIN,TM72,FRONT 2 28407 14 CABLE,5/16",BULK (QTY IN FEET) 3 22993 91 CHAIN,5/16",GR30,9 LINK 4 28408 4 U-BOLT,CABLE,5/16" (NOT SHOWN) --- 31932 - GUARD,CHAIN,TM60,REAR,ASSY 5 31864 1 GUARD,CHAIN,TM60,REAR 6 3[...]

60IN SIDE TSR ROTARY MOWER ©2011 Alamo Group Inc. Parts Section 6-22 COMMON SIDE ROTARY[...]

60IN SIDE TSR ROTARY MOWER Continued... ITEM PART NO. QTY. DESCRIPTION 1 34975 1 HEAVY DUTY GRASSKAT COMBO ------ 06320005 1 STD DUTY GRASSKAT COMBO ------- 06320008 1 HEAVY DUTY GRASSKAT CABLE 2 34980 1 SPINDLE ASSY,TM 60" 3 06504016 1 CURRENT MOTOR,(M365-1 1/4" 14-SPLINE) 4 06410254 2 SKID,OUTBOARD,TM60 5 22992 156 CHAIN,10 LINK 6 6T227[...]

60IN SIDE TSR REAR GUARDS ©2011 Alamo Group Inc. Parts Section 6-24 COMMON SIDE ROTARY[...]

60IN SIDE TSR REAR GUARDS Continued... ITEM PART NO. QTY. DESCRIPTION 1 34973 2 ROD,CHAIN,OUTER,TM60 2 34974 2 ROD,CHAIN,INNER,TM60 3 21631 16 CAPSCREW, 3/8 X 1-1/4,NC 4 34972 4 PLATE,CAP,CHAIN 5 21625 30 HEX NUT,3/8",NC 6 21988 16 LOCKWASHER, 3/8" 7 22992 156 CHAIN,10 LINK 20 06410947 1 MNT,FLAP,RH,EXT,TSR 21 06401184 2 STRAP,FLAP,EXT,TS[...]

SIDE ROTARY CASTER WHEEL ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-26 COMMON SIDE ROTARY[...]

SIDE ROTARY CASTER WHEEL ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 25214C 1 FRAME,CASTER,WHL (TM60) --- 28297A - FRAME,CASTER WHL (TM72) 2 22057 1 SPINDLE,CASTER AXLE,ASSY 3 6T2617 2 BUSHING,MACH,1-1/2IDX 2-1/4OD 4 28548 1 CASTER WHEEL,SOLID TIRE --- 22065 1 HUB,ASSY,CASTER 22066 1 HUB,CASTER 22070 1 DUST CAP 22071 5 HUB STUD 22073 1 H[...]

CASTER WHEEL ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 21459 1 SPINDLE,CASTER WHEEL AXLE 2 21987 5 LOCKWASHER,5/16” 3 21575 5 HEX NUT,5/16” 4 28548 5 CAPSCREW,5/16” X 3/4”,NC 5 22697 1 RIM,OUTER,CASTER ASSY 6 21416 1 TIRE,SOLID 7 22696 1 RIM,CASTER WHEEL 8 22070 1 DUST CAP 9 22533 1 COTTER PIN,3/16” X 2” 10 6T0836 2 CUP,CASTER WHEEL 11 [...]

ROTARY DISK AND KNIVES ITEM PART NO. QTY. DESCRIPTION 1 34876 1 BLADE MOUNTING DISK 2 6T1023R 2 NYLOCK NUT,1-1/8” 3 34878 2 SPACER 4 34497 2 KNIFE MOUNTING BOLT 5 34685 2 KNIFE,60" HIGH SUCTION - STANDARD 5A 34684 2 KNIFE,60" - OPTIONAL 6 34682 2 KNIFE 72” (MOUNT ON 72” MOWER ONLY) 7 25270 6 FLATWASHER,5/8",USS,GR8 8 6T2290 6 C[...]

TM MOWER SPINDLE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-30 COMMON SIDE ROTARY[...]

TM MOWER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 6T1024H5 - SPINDLE ASSEMBLY COMPLETE 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT - THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT - THIN 5 6T1014 1 BEARING ADJUSTMENT SLEEVE 6 6T1011 1 UPPER SEAL - SET OF 2 7 6T1012 1 BEARING CONE 8 6T1013 1 BEARING CUP 9[...]

TSR MOWER SPINDLE ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-32 COMMON SIDE ROTARY[...]

TSR MOWER SPINDLE ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION ------ 34980 - SPINDLE ASSEMBLY COMPLETE 1 34978 1 SPINDLE MOUNT 2 34979 1 SPINDLE,TM60 3 6T1013 1 BEARING CUP 4 6T1012 1 BEARING CONE 5 6T1011 1 UPPER SEAL - SET OF 2 6 6T1014 1 BEARING ADJUSTMENT SLEEVE 7 6T1013H 1 BEARING,CUP,HD 8 6T1012H 1 BEARING CONE,HD 9 6T1011H 1 SEAL,LO[...]

60IN AND 72IN ROTARY MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-34 COMMON SIDE ROTARY[...]

60IN AND 72IN ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504011 - MOTOR ASSEMBLY,TM60 06504018 - MOTOR ASSEMBLY,TM72 1 22790 1 END,COVER 2 06504088 1 HOUSING, PEC 3 06504062 1 HOUSING, GEAR 4 06504090 1 SET, GEAR SHAFT,TM60 ------ 06504105 - SET, GEAR SHAFT,TM72 5 06504104 4 CAP SCREW,TM60 ------ 06504106 - CAP SCREW,TM72 [...]

60IN TSR ROTARY MOTOR BREAKDOWN ©2011 Alamo Group Inc. Parts Section 6-36 COMMON SIDE ROTARY[...]

60IN TSR ROTARY MOTOR BREAKDOWN Continued... ITEM PART NO. QTY. DESCRIPTION 06504016 - MOTOR(M365-1 1/4SPLINE),SEALED 1 22790 1 COVER,END 2 06504088 1 HOUSING,PEC 3 06504111 1 HOUSING,GEAR 4 06504110 1 SET,GEAR SHAFT 5 06504104 4 CAP SCREW 6 06504078 2 SCREW,DRIVE 7 06504093 4 PIN,DOWEL 8 06504094 1 NAME PLATE 9 06504095 2 THRPL 10 02961940 1 PLUG,[...]

FRONT HYDRAULIC PUMP BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 23152 - PUMP ASSEMBLY 1 3/4” COMPLETE 1 22765 1 SEAL 2 22766 1 SHAFT END COVER 3 22767 2 CHECK AND END COVER 4 22768 2 BUSHING 5 22769 2 CHANNEL SEAL 6 22770 2 THRUST PLATE 7 22771 1 DRIVE SHAFT AND GEAR SET 1 3/4” 8 22772 2 GASKET SEAL 9 22773 4 DOWEL PINS 10 22774 1 GEAR HOU[...]

RESERVOIR TANK FILTER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION ------ 06505044 - FILTER ASSY SAE 10 MICRON 1 28583 4 CAPSCREW,8MM X 25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 SEAL KIT 4 06505047 1 SPRING 5 06505048 1 BYPASS 6 35259 1 FILTER,10 MIC,RETURN LINE 7 06505049 1 CAN/BODY ©2011 Alamo Group Inc. Parts Section 6-39 COMMON SIDE ROTARY[...]

COOLER ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-40 COMMON SIDE ROTARY[...]

COOLER ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 21530 10 CAPSCREW,1/4 X1 NC 2 21986 10 LOCKWASHER,1/4 3 22014 10 FLATWASHER,1/4 4 35176 10 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 MNT,COOLER,BUMPER TANK,RH 7 06380007 1 MNT,COOLER,BUMPER TANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CAPSCREW,3/8 X 3/4 NC 10 21988 4 LOCK[...]

3IN X 10IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 6T0151R - HYD. CYLINDER 3" X 10" 1 6T0167 1 CYLINDER BUTT 2 6T0170 1 CYLINDER GLAND 3 6T0178 1 CLEVIS END 4 6T0164 1 CYLINDER TUBE 5 6T0161 1 PISTON ROD 6 6T0173 1 PISTON 7 6T0179 1 LOCKNUT 8 6T0176 4 TIE ROD ASY ------ 6T0187 - SEAL KIT 9 ------ 2 O - RING 10 -[...]

3IN X 12IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 32215 - HYD. CYLINDER 3" X 12" (STD DUTY) 25343 - HYD. CYLINDER 3" X 12" (HVY DUTY) 1 6T0167 1 CYLINDER BUTT 2 6T0170 1 CYLINDER GLAND 3 6T0178 1 CLEVIS END 4 6T0204 1 CYLINDER TUBE 5 6T0203 1 PISTON ROD 6 6T0173 1 PISTON 7 6T0179 1 LOCKNUT 8 6T0205 4 [...]

3IN X 18IN HYDRAULIC CYLINDER BREAKDOWN ITEM PART NO. QTY. DESCRIPTION ------ 6T0150 - CYLINDER 3" X 18" 1 6T0167 1 CYLINDER BUTT 2 6T0170 1 CYLINDER GLAND 3 6T0178 1 CLEVIS END 4 6T0165 1 CYLINDER TUBE 5 6T0162 1 PISTON ROD 6 6T0173 1 PISTON 7 6T0179 1 LOCKNUT 8 6T0177 4 TIE ROD ASY ------ 6T0187 - SEAL KIT 9 ------ 2 O - RING 10 ------ [...]

NOTES 1 ©2011 Alamo Group Inc. Parts Section 6-45 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 30801 ©2011 Alamo Group Inc. Parts Section 6-46 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 30801 Continued... ITEM PART NO. QTY. DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 VALVE SECTION (SINGLE ACTING, SPRING DETENT) 4 06502091 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (NO AUX VALVE PORTS) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT-OFF PLUG 8 TB1017E 1 R[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31320 ©2011 Alamo Group Inc. Parts Section 6-48 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31320 Continued... ITEM PART NO. QTY. DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 N/A - N/A 8 6T4209 1 RELIEF PLUG 9 31862 1[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31321 ©2011 Alamo Group Inc. Parts Section 6-50 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31321 Continued... ITEM PART NO. QTY. DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF VALVE, 360 PSI 7 N/A - N/A 8 6T4209 1 RELIEF PLUG 9 [...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31752 ©2011 Alamo Group Inc. Parts Section 6-52 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 31752 Continued... ITEM PART NO. QTY. DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 VALVE SECTION (SINGLE ACTING, SPRING DETENT) 4 TB1017P 1 VALVE SECTION (SINGLE ACTING, SPRING DETENT) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT-OFF PLUG 8 TB1017E 1 RELIEF VALVE, 2250 PSI [...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502040 ©2011 Alamo Group Inc. Parts Section 6-54 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502040 Continued... ITEM PART NO. QTY. DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) 4 31597 1 VALVE SECTION (DOUBLE ACTING, CENTER SPRING) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 06503068 1 RELIEF[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502042 ©2011 Alamo Group Inc. Parts Section 6-56 COMMON SIDE ROTARY[...]

CABLE (MANUAL) LIFT VALVE BREAKDOWN - 06502042 Continued... ITEM PART NO. QTY. DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31600 1 VALVE SECTION (DOUBLE ACTING, DETENT FLOAT) 4 31600 1 VALVE SECTION (DOUBLE ACTING, DETENT FLOAT) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF VALVE, 360 PSI 7 06503068 1 R[...]

BRAKE VALVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION * 06510083 - BRAKE VALVE, ASSY 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34095 1 RELIEF VALVE, 3000 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI ©2011 Alamo Group Inc. Parts Section 6-58 COMMON SIDE RO[...]

BRAKE VALVE HYDRAULIC SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-59 COMMON SIDE ROTARY[...]

CABLE DRAFT BEAM TRAVEL LOCK ITEM PART NO. QTY. DESCRIPTION 1 ------ - CABLE DRAFT BEAM 2 6T0106 1 TRAVEL LOCK BRACKET 3 6T0107 2 TRAVEL LOCK PINS 3/4” X 3 1/4” 4 6T3020 2 R - CLIP 5/32” 5 21833 1 CAPSCREW 3/4” X 2 1/4” 6 21825 1 HEX NUT 3/4” 7 21993 1 LOCK WASHER 3/4” 8 22021 1 FLAT WASHER 3/4” 9 22600 1 TRAVEL LOCK EAR 10 22604 2 [...]

COMBO DRAFT BEAM TRAVEL LOCK ITEM PART NO. QTY. DESCRIPTION 1 ------ - COMBO DRAFT BEAM 2 6T0106 1 TRAVEL LOCK BRACKET 3 21833 1 CAPSCREW 3/4” X 2 1/4” 4 ------ - MAIN FRAME *REFER TO PARTS SECTION 5 33856 1 BRKT,PIN HOLDER 6 21988 2 LOCK WASHER 3/8” 7 21629 2 CAPSCREW 3/8” X 3/4” 8 6T3020 2 R - CLIP 5/32” 9 6T0107 2 TRAVEL LOCK PINS 3/[...]

SWITCH BOX ITEM PART NO. QTY. DESCRIPTION 1 06514013 1 SWBX,ALUM,BLK,06510102 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 33811 1 SWITCH,MASTER/DECK FLOAT 4 6T3923 1 INDICTATOR LIGHT,ON,RED 5 06514014 1 BREAKER,10A,SWBX 6 34540 1 STRAIN RELIEF,3/4,BLACK,NYLON 7 06550018 1 DECAL,SWTCHBX,TM/TSF,CG 8 35227 1 RELAY,DP,DT,12V,LY2F,35226 ©2011 Alamo Group Inc. [...]

SWITCH BOX SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-63 COMMON SIDE ROTARY[...]

NOTES 2 ©2011 Alamo Group Inc. Parts Section 6-64 COMMON SIDE ROTARY[...]

FIRE SUPRESSION SYSTEM ©2011 Alamo Group Inc. Parts Section 6-65 COMMON SIDE ROTARY[...]

FIRE SUPRESSION SYSTEM PARTS ©2011 Alamo Group Inc. Parts Section 6-66 COMMON SIDE ROTARY[...]

FIRE SUPRESSION SYSTEM PARTS Continued... ITEM PART NO. QTY. DESCRIPTION 1 06520357 1 TANK,FIRE SUPRESS SYS 2 06520358 1 MNT,TANK,FIRE KIT 3 06520359 1 PUMP,FIRE SUPRESS SYS 4 6T2181 4 CAPSCREW,SKT HD,10/24 X 3/4 5 24890 4 HEX NUT,10-24 NYLOCK 6 06520360 1 HOSE REEL,FIRE KIT 7 21630 4 CAPSCREW, 3/8 X 1,NC 8 21627 8 NYLOCK NUT,3/8",NC 9 0652036[...]

FIRE SUPRESSION SYSTEM ELECTRICAL SCHEMATIC ©2011 Alamo Group Inc. Parts Section 6-68 COMMON SIDE ROTARY[...]

WETCUT ©2011 Alamo Group Inc. Parts Section 6-69 COMMON SIDE ROTARY[...]

WETCUT 50 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370136 1 MNT,TANK,50GAL,WETCUT 4 06520342 1 TANK,50GA.,WETCUT 7 RD1032 3 PIN,LYNCH 1/4" X 2" 8 TB1036 1 PIN,SEC BOOM SWIV 1X4-11/16" 9 06520343 4 ANCHOR,STRAP,WETCUT 10 06520344 4 BOLT,STRAP,TANK,WETCUT 11 06520345 2 STRAP,TANK,WETCUT ©2011 Alam[...]

WETCUT 100 OR 150 GALLON TANK MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06370138 1 MNT,TANK,100GAL,WETCUT ------ 06370139 - MNT,TANK,150GAL,WETCUT 4 06520372 1 TANK,100GA.,WETCUT ------ 06520373 - TANK,150GA.,WETCUT 5 21527 2 HEX NUT,NYLOCK,1/4" NC 6 21530 2 CAPSCREW,1/4" X 1" NC 7 RD1032 3 PIN,LYNCH 1/4" [...]

WETCUT TANK PLUMBING ©2011 Alamo Group Inc. Parts Section 6-72 COMMON SIDE ROTARY[...]

WETCUT TANK PLUMBING Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370128 1 MNT,3PNT,UNI 2 06520336 1 CNTRLR,SENSOR,06520333 3 06520341 1 PUMP,WETCUT 4 06520346 1 FITTING,BULKHEAD,WETCUT 5 06520347 1 FITTING,ELBOW,WETCUT 6 06520348 1 VLV,BALL,WETCUT 7 06520349 6 FITTING,BARB,HOSE,WETCUT 8 06520352 4 FITTING,NIPPLE,1/2X3/8,WETCUT 9 06520353 1 FITT[...]

WETCUT SPRAYER HEAD ASSEMBLY ©2011 Alamo Group Inc. Parts Section 6-74 COMMON SIDE ROTARY[...]

WETCUT SPRAYER HEAD ASSEMBLY Continued... ITEM PART NO. QTY. DESCRIPTION 1 06370105 1 HOOD,SPRAYER 2 06370106 1 HINGE,LH,SPRAYER 3 06370107 1 HINGE,RH,SPRAYER 4 06370108 1 HINGE,CNTR,SPRAYER 5 06410668 1 GUARD,SPRAYER,WETCUT 6 06410753 1 MNT,RH,WET CUT 7 06410754 1 MNT,LH,WET CUT 8 06410796 1 GUARD,HOSE,WETCUT 9 06420069 3 PIN,HINGE,WET CUT 10 0649[...]

WETCUT CABLES ©2011 Alamo Group Inc. Parts Section 6-76 COMMON SIDE ROTARY[...]

W ARRANTY SECTION Warranty Section 7-1[...]

.[...]

W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the f[...]

ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an[...]

T O THE OWNER / OPERA TOR / DEALER T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health A[...]

Printed in USA © T iger Corporation[...]