Toshiba A130 Bedienungsanleitung

Toshiba Personal Computer Satellite A130/ A135 Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL][...]

ii [CONFIDENTIAL] Satellite A130/ A135 Series Maintenance Manual Copyright © 2006 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Toshiba P[...]

Satellite A130/ A135 Series Ma intenance Manual [CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite A130/ A135, referred to as the M100 Series in this manual. The procedures described in this manual are intended to help service technicians isolate fault[...]

iv [CONFIDENTIAL] Satellite A130/ A135 Series Maintenance Manual The manual is divided into the following parts: Chapter 1 Hardware Overview describes the M100 Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diag[...]

Satellite A130/ A135 Series Ma intenance Manual [CONFIDENTIAL] v Some operations require you to simultaneously use two or m ore keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the sam e time press Pause (Break) . If three keys are used, hol[...]

vi [CONFIDENTIAL] Satellite A130/ A135 Series Maintenance Manual Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ......... 1-1 1.2 System Unit ................................................................................[...]

Satellite A130/ A135 Series Ma intenance Manual [CONFIDENTIAL] vii 2.19 2 nd HDD Troubleshooting……………………………………..…………………….....2-46 Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test…………………………………….……...………………………..3-3 3.2 Executing the Diagnostic Test…[...]

viii [CONFIDENTIAL] Satellite A130/ A135 Series Maintenance Manual 4.7 Wireless LAN Unit .......................................................... ..............................................4-20 4.8 Modem........................................................................ ...................................................4-24 4.9 Optical D[...]

Chapter 1 Hardware Overview 1 [CONFIDENTIAL][...]

1 Hardware Overview 1-ii Satellite A130/ A135 Maintenance Manua l[...]

1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-iii Chapter 1 Contents 1.1 Features ................................................................................................................... ... 1-1 1.2 System Unit ........................................................................................................[...]

1 Hardware Overview 1-iv Satellite A130/ A135 Maintenance Manua l Figures Figure 1-1 2.5-inch HDD ................................................................................................ 1-6 Tables Table 1-1 2.5-inch HDD specifications ......................................................................... 1-7 Table 1-2 DVD-ROM & CD-R[...]

1.1 Features 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-1 1.1 Features The Satellite A130 Series Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (C MOS) technology extensively to provide compact size, minimum weight and high reliability. This computer inco rporat[...]

1 Hardware Overview 1.1 Features 1-2 Satellite A130/ A135 Series Maintenance Manual • Four USB (V2.0) ports • One DDC2b compliant 15-pin VGA port (RGB) • One S-Video port • One microphone port • One headphone-out jack • Digital volume control by encoder • Wireless communication switch • One DC-in jack • One RJ-11 jack for 56kbps V[...]

1.1 Features 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-3 1 programmable launch button (IE button) 1 programmable launch button (CD/DVD start) • Control buttons for CD/DVD play buttons (4 buttons) Play/Pause Stop/Eject Next Previous • Magnetic Lid switch controlled by software.  Security • Fingerprint authenticat[...]

1 Hardware Overview 1.1 Features 1-4 Satellite A130/ A135 Series Maintenance Manual • USB memory boot support  Power • Universal AC adapter, 90~264VAC, 47~63Hz.  Offers constant voltage 19V output source with 65W, 75W or 90W max output power capacity • 4 cells of Li-Ion 18650 size, smart batte ry pack with 2000mAH x 14.4V (28.8W ) • 6[...]

1.2 System Unit 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-5 1.2 System Unit The system unit is composed of the following m ajor components:  Processor • Intel Core Duo processor, T2050/T2250 • Intel Core Solo processor, T1350 • Intel Core 2 Duo processor, T5500/ T5600/ • T7200/ T7400 / T7600 • Intel Core 2 D[...]

1 Hardware Overview 1.3 2.5-inch Hard Disk Drive 1.3 2.5-inch Hard Disk Drive The internal HDD is a random access non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-W inchester type magnetic heads. The computer supports up to 200G HDD. The HDD is shown in Figure 1-1. Speci fications are listed in Table 1-1. Figure 1[...]

1.4 Optical Disk Device 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-7 Hitachi HDD Buffer (MB) 8 8 8 8 8 8 N/A Fujitsu HDD Buffer (MB) 8 8 8 8 8 8 8 Bytes per sector 512 512 512 512 512 512 512 Table 1-1 2.5-inch HDD specification[...]

1 Hardware Overview 1.4 Optical Disc Device 1-8 Satellite A130/ A135 Series Maintenance Manual 1.4 Optical Disc Device 1.4.1 DVD-ROM & CD-RW The DVD-ROM and CD-RW drive accepts 12-cm ( 4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and high spee[...]

1.4 Optical Disk Device 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-9 1.4.2 DVD Super Multi Double Layer The DVD Super Multi drive accepts 12-cm (4.72-inc h) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and CD-RW at 10x and DVD-R at[...]

1 Hardware Overview 1.5 Power Supply 1-10 Satellite A130/ A135 Series Maintenance Manual 1.5 Power Supply This specification defines the performance and characteristics of the 65W/ 75W/ or 90W AC adapter power supply. It supplies a constant voltage 19V output source for the IAKAA Series Personal Computer.  A/D conversion • The EC uses 10-bit s[...]

1.5 Power Supply 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-11  Battery charging control • The EC controls the following. – The quick charging ON/OFF – The detection of full charge  Detection of the low battery • The EC detects the low batte ry point by the gas gauge. – LB10M: The system will be driven b y[...]

1 Hardware Overview 1.6 Batteries 1-12 Satellite A130/ A135 Series Maintenance Manual 1.6 Batteries The computer has two types of battery:  Main battery pack (18650 size)  RTC battery The removable main battery pack is the compute r’s main power source when the AC adapter is not attached. The battery specifications are listed in the table b[...]

1.6 Batteries 1 Hardware Overview Satellite A130/ A135 Series Maintenance Man ual 1-13 1.6.1 Main Battery Battery charging is controlled by a power supply microprocessor that is mounted on the system board. The power supply microprocessor controls wh ether the charge is on or off and detects a full charge when the AC adapter and battery are attache[...]

1 Hardware Overview 1.6 Batteries 1-14 Satellite A130/ A135 Series Maintenance Manual 1.6.2 RTC battery The RTC battery provides power to keep the curr ent date, time and other setup information in memory while the computer is turned off. The table below lists the charging time and data preservation period of the RTC battery. The RTC battery is cha[...]

Chapter 2 Troubleshooting Procedures 2[...]

[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 1 Chapter 2 Contents 2.1 Troubleshooting Introduction ........................................................................................3 2.2 Troubleshooting Flowchart ..................................................................[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 2 Figures Figure 2-1 Troubleshooting flowchart (1/2) ....................................................................... 5 Figure 2-1 Troubleshooting flowchart (2/2) ......................................................................[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 3 2.1 Troubleshooting Introduction Chapter 2 describes how to determine if a Fi eld Replaceable Unit (FRU) in the com puter is causing the computer to malfunction. The FRUs covered are: 1. Display 6. TouchPad 11. IEEE 1394 port 2. USB Flopp[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 4 2.2 Troubleshooting Flowchart If you know the location of the ma lfunction, turn directly to the appropriate section of this chapter. If the problem is unspecified, use the flowchart in Figure 2-1 as a guide for determining which troubles[...]

2 Troubleshooting Procedures STA R T C onnect t he A C ad apt er t o the D C - IN socket Is the D C -IN L E D o n? Is th e B a tter y L E D o n ? T u rn th e P o w e r s w itc h o n I s t h e Po we r On LE D o n ? I s t he " T os hi ba" log o m es sage di s pl ay ? If t he "pa ssw o rd" m essag e d i sp l ays, t yp e the p assw [...]

2 Troubleshooting Procedures A Does ty ped characters appear corre ctly? Insert the diagnostics disk into the FDD. Then run the diagno stics test program. Is the diagnostics test loaded? Allow each test to perform automatically Is an error detected by any of the diagnostics tests? Sy stem is normal End Ye s Ye s Ye s No Perform the Key board Troubl[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 7 If the diagnostics program cannot detect an erro r, the problem may be intermittent. The test program should be executed several times to isol ate the problem. W hen a problem has been located, perform the appropriate trou bleshooting pro[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 8 Other problems that are not covered by the di agnostics program may be discovered by a user. 1. If an error is detected when using an ex ternal USB device, perform the External USB Devices Troubleshooting pr ocedures in Section 2.6. 2. If[...]

2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting STA RT A re t he D C - IN and B a tte ry L E D s li t? Can you tur n the com puter on? Are the i nterna l power connecti ons secure? END Check P ow er Supply Stat us (Procedure 1) No Ye s Check power s uppl y connecti ons (Procedure 3) Run di agn ost ic prog ram (P roc ed ure 4 ) Ye s No[...]

2 Troubleshooting Procedures The power supply controls many functions and components. To determ ine if the power supply is functioning properly, star t with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 give s a summary of the proc ess. The procedures described in this section are: Procedure 1: Power [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 11 Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid Blue). Off No AC po wer exists. To check the power supply status, install a ba ttery pack and connect an A C adaptor to the DC-IN port on the comput[...]

2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor Sys t em boar d B a tter y A C adaptor cord AC p o we r c o r d Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 13 Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power . If you cannot turn on the power, go to Proce[...]

2 Troubleshooting Procedures 2.4 Display Troubleshooting P er f orm ext ernal dis p l ay check (P ro ce du re 1 ) ST AR T D o es t he ex t ernal d isp la y fu nc tio n o k ? P e rf orm di agno s ti c check (P ro ce du re 2 ) No W as a disp lay pr obl em det ec t ed? P er f o r m connect o r and re place m ent check (P ro ce du re 3 ) R e pl ac e s [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 15 This section describes how to determ ine if th e computer’s display is functioning properly. The process is outlined in Figure 2-3. Start wi th Procedure 1 and continue with the other procedures as instructed. Procedure 1: External dis[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 16 Procedure 3 Connector and replacement check The FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions o[...]

2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting P e rf orm ext ernal ke yboard check (P ro ce du re 1 ) ST AR T D o es t he ex t ernal keyboard f uncti o n ok? P e rf orm di agno s ti c check (P ro ce du re 2 ) Wa s a k e y b o a r d pr obl em det ec t ed? P er f o r m connect o r and re place m ent check (P ro ce du re 3 ) R e pl ac e s [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 18 To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-5 outlines the p rocess. St art with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External ke[...]

2 Troubleshooting Procedures 2.6 External USB Devices Troubleshooting R epl ace sy st em board (Procedure 2) END O rig in a l U S B devi ce i s f aul t y P e rf orm ext ernal devi ce and connect ion check (Procedure 1) ST AR T D oes t he device func t ion w hen connect ed to a di f f erent U S B port ? D oes an al t er nat ive U SB d e vic e fu nc [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 20 To determine if the computer’s external US B devices are functioning properly, perform the following procedures. Figure 2-6 outlines the proce ss. Start with Procedure 1 and continue as instructed. Procedure 1: External device and conn[...]

2 Troubleshooting Procedures 2.7 TV-Out Failure Troubleshooting P e rf orm T V connect i on check (Procedure 1) ST AR T D oes r ep l acem ent T V cabl e f uncti o n pr op e rl y? P e rf orm T V s et check (Procedure 2) R epl ace sy st em board END No R epl ace T V cable No T V f unct i o ni ng ok? Ye s U se dif ferent T V set No Figure 2-6 TV-out t[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 22 To determine if the computer’s TV-out por t is functioning properly, perform the following procedures. Figure 2-7 outlines the p rocess. Start with Procedure 1 and co ntinue as instructed. Procedure 1: TV connection check Procedure 2: [...]

2 Troubleshooting Procedures 2.8 TouchPad Troubleshooting START END TouchPad connection check (Procedure 1) TouchPad replacement check (Procedure 2) Replace sy stem board Figure 2-7 Touchpad troubleshooting process Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 23[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual [CONFIDENTIAL] 24 To determine if the computer’s built-in T ouchPad is functioning properly, perform the following procedures. Figure 2-9 outlines the proce ss. Start with Procedure 1 and continue as instructed. Procedure 1: TouchPad connection check Pr[...]

2 Troubleshooting Procedures 2.9 Speaker Troubleshooting START Do al l sour ces have sam e problem? END Per form ea rphone test (Procedure 2 ) Do earphones function correctly ? Perform connection ch eck (Procedure 3 ) Perform replacement check (Procedure 4 ) Perform audio sou rce tes t (Procedure 1 ) No Ye s Yes Replace sy stem board Speakers are n[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 26 To determine if the computer’s built-in sp eakers are function ing pr operly, perform the following procedures. Figure 2-10 outlines the p ro cess. First adjust the speaker volume to an appropriate level. Start with Proced ure 1 and c[...]

2 Troubleshooting Procedures 2.10 Optical Drive Troubleshooting START Audio CD fu nctions ok? END Perform softw are check (Procedure 3) Perform diagnostic test (Procedure 4) Perfo rm connection and replacem e nt check (Procedure 5) Perfor m a udio C D che ck (Procedure 1) Perf orm drive- cleaning chec k (Procedu re 2) No Yes Replace sy stem board F[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 28 This section describes how to determ ine if the computer’s internal optic al drive is functioning properly. The Satellite A130/A 135 /Satellite Pro A130 module bays can accommodate the following optical drives: DVD SuperMulti supporti[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 29 Procedure 5 Connection check and replacement check The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be dam aged. Disassemble the computer following the steps described in Ch[...]

2 Troubleshooting Procedures 2.11 Modem Troubleshooting ST ART Com p uter u nable to detect t eleph one si gnal ? END Perform connection check (Procedure 2) Perform replacemen t check (Procedure 3) Perform telephone line connection check (Procedure 1) Check / replac e teleph one line and connect ions Yes Replace sy stem board No Figure 2-10 Modem t[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 31 This section describes how to determine if the computer' s modem is functioning properly. Figure 2-12 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Pro[...]

2 Troubleshooting Procedures 2.12 PCMCIA Troubleshooting STAR T Do errors occur during SYCARD test? Perf orm PCMCI A s ocket replacem ent c heck (Proced ure 2) Replace s ys tem board END P CM CIA unit is not faulty. Perform SYCA RD test (Proced ure 1) No Yes Figure 2-11 PCMCIA troubleshooting process Satellite A130/A135 /Satellite Pro A130 Series M[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 33 This section describes how to determ ine if th e PCMCIA card player is functioning properly. The process is summarized in Figure 2-13. Perf orm the steps below starting with Procedure 1 and continuing with the othe r procedures as requi[...]

2 Troubleshooting Procedures 2.13 IEEE 1394 Troubleshooting START Per for m IEEE 1394 devi ce check (Proce dure 1) I s I E EE 13 94 transmissi on ok? Perform diagno stic check (Proce dure 2) W as a n I EEE 1394 pr oble m dete ct ed? Perform con nection and replacem ent check (Proce dure 3) R eplace system bo ard END Yes Yes I EEE 1394 port an d tra[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 35 To determine if the computer’s IEEE 1394 system is functioning properly, perform the following procedures. Figure 2-14 outlines the p rocess. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: IE[...]

2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting START Perform diagnostic test (Procedure 1) Was a w ireless L AN prob lem delec ted? Perform connector and replacement check (Procedure 2) Repl ace wireles s LAN antenna/ unit Replace sy stem board END Yes Wirele ss L AN sy stem is not faulty . Continue troubleshooting - refer to Figur [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 37 The wireless LAN antenna wire, wireless LAN un it or system board may each be th e source of a wireless LAN fault. Any of these com ponents may be dam aged. To determine if the computer’s wireless LAN system is functioni ng properly, [...]

2 Troubleshooting Procedures 2.15 Finger printer Troubleshooting Figure 2-14 Finger printer troubleshooting process Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 38[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 39 The Finger printer board or system board may be the reason of a finger prin ter fault. Either of these two components may be damaged. To determine if the com puter’s Finger printer is functioning properly, perform the following proc e[...]

2 Troubleshooting Procedures 2.16 Bluetooth Troubleshooting ST A R T P r e f or m di a gnos t i c t es t ( P r oc e dur e 1) W a s a Bl uet oot h pr obl e m de t e c t ? Bl ue t oot h i s not f a ul t y . C ont i nue t r oubl e s hoot i ng- r e f e r to F i g u re 2 . 1 Rep l ac e sy st em b o ar d P e r f or m conne ct or and r ep l ac emen t c h [...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 41 The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be dam aged. To determine if the computer’s Bluetooth is functioning properl y, perform the following pro[...]

2 Troubleshooting Procedures 2.17 4 in 1 card Troubleshooting START Do err ors o ccur du ring 4 IN 1 CARD te st ? Perform 4 IN 1 card socket replacement check (Proce du re 2) Replace system board END 4 IN 1 unit is not faulty. Perform 4 in 1 C AR D test (Proce du re 1) No Yes Figure 2-16 4 in 1 card troubleshooting process Satellite A130/A135 /Sate[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 43 This section describes how to determ ine if the 4 IN 1 Card player is functioning properly. The process is summarized in Figure 2-16. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required[...]

2 Troubleshooting Procedures 2.18 1 st HDD Troubleshooting Figure 2-17 HDD troubleshooting process Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 44[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 45 The 1 st HDD or system board may be the reason of a HDD fault. Either of these two components may be damaged. To determine if the com puter’s 1 st HDD is functioning properly, perform the following procedures. Fi gure 2-15 outlines th[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 46[...]

2 Troubleshooting Procedures 2.19 2 nd HDD Troubleshooting Figure 2-18 2 nd HDD troubleshooting process Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 47[...]

2 Troubleshooting Procedures Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manua l [CONFIDENTIAL] 48 The 2 nd HDD or system board may be the reason of a HDD fault. Either of these two components may be damaged. To determine if the com puter’s 2 nd HDD is functioning properly, perform the following procedures. Fi gure 2-15 outlines th[...]

3. Tests and Diagnostics Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-1 Chapter 3 Tests and Diagnostics 3[...]

Contents 3.1 The Diagnostic Test ........................................................................................................ .3 - 3 3.2 Executing the Diagnostic Test.......................................................................................... 3-4 3.3 Display Configuration ...................................................[...]

3. Tests and Diagnostics Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-3 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Dallas10&10G T&D version 1.0) hardware modules. The Test & Diagnostic Program is stored on the T&D diskettes. [...]

3. Tests and Diagnostics 3-4 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3.2 Executing the Diagnostic Test DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the diagnostics diskette #1 in the floppy disk drive and turn on the computer. (The diagnostics diskette conta[...]

3. Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-5[...]

3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “ Y ” key pressed. 3-6 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics It will skip this process if “N” key pressed. And then it will check if it’s necessary to leave this program. Program will quit when “ Y ” key pressed and it will go back main menu f or next test if “ N ” key pressed. Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-7[...]

3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes:  CPU type (Single/ Dual Yunah; Cache ; CPU speed ;CPU FSB)  DDRAM SIZE  ODD TYPE ((DVD-SuperMulti; COMBO; …)  Panel ID  HDD type & capacity (Vendor ID. M odel .Firmware)  VRAM size / VGA CHIP TYPE  Battery cell (6ce[...]

3 Tests and Diagnostics 3.4 Speaker Audio Test The speaker audio test allows the user to aurally confirm the speaker functions. And check both speakers if they are OK within 3 times “Beep” sound generated. NOTE : Remember to tune up the volume as “ Maximum ” before this test starts. The screen should display as below, indicating whether the[...]

3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test:  The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE : Remember to approach f[...]

3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE : The AC adaptor ( 90W, 19V ) should be connected to successfully run this test. This test shows and measures the main battery:  Battery type (Lion)  Manufacturer (Sanyo/Panasonic/Sony)  Remain charge capacity (0 ~ 100%)  Charge function (PASS/FAIL) - “Battery Is Full” showe[...]

3 Tests and Diagnostics 3. 7 FDD Test NOTE : Before running the FDD test, prepare a formatted work diskette (1.44 MB). Remove the diagnostics diskette and insert the work diskette into the FDD. The contents of the floppy diskette maybe erased. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ [...]

3. Tests and Diagnostics 3. 8 ODD Test The ODD test allows a user to aurally confirm the ODD functions. NOTE : A CD disc (including data file) must be inserted into the ODD drive then must wait ODD drive initial OK (ODD LED stop flashing) before this test starts . The ODD test includes two subtests of the: 1. Random read/partial sequential read fun[...]

3 Tests and Diagnostics 3-14 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1. K (UK, for Eur[...]

3. Tests and Diagnostics Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-15[...]

3. Tests and Diagnostics 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “ Tab ” key to move between selections: 1. Mouse Speed (on a scale from slow to fast) 2. Acceleration (Off, Low, Medium, High) 3. Button Assignments (Left + Right / Right button, either Unassigned or[...]

3. Tests and Diagnostics Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-17 After checking T/Pad buttons and cursor’s function, use “Tab” key or use T/Pad cursor to click the “OK” column will end this test. It will indicate whether the subtests pass or fail after three questions. NOTE: The above figure has three compar[...]

3. Tests and Diagnostics 3. 11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2. VGA Mode - including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors), 8[...]

3. Tests and Diagnostics 3.12 Magnetic Switch Test The lid switch test checks the lid function of the unit. When LCD cover closed, the lid should enable to turn off the display. NOTE : Remember to tune up the volume as “ Maximum ” before this test starts. Follow below steps to run this test: 1. Close the LCD cover. 2. Heard 3 “Beep” sound h[...]

3. Tests and Diagnostics 3-20 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen:  IO Base – Port: A000H  IRQ – BH, it’s “IRQ 10”.  Node – it [...]

3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-21[...]

3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: 3-22 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by com paring the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-23[...]

3. Tests and Diagnostics 3.15 Read 1394 GUID This test will check if the computer’s EEPROM 1394GUID code is correct. NOTE: Must open the RAM Door to see RAM connector GUID bar code before test item begins. The figure below will be displayed: 3-24 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics 3.16 Speaker EQ Type Check&Re-Write This test will check if the computer’s EEPROM EQ type is correct. The EQ Type test includes two subtests of the: 1. Read EQ Type from EEPROM 2. Re-Write EQ Type to EEPROM NOTE : To execute this test, you must select speaker type (Harman or No brand). The figure below will be display[...]

3. Tests and Diagnostics 3.17 Button Test The control button test allows the user to manually test each of the five CD control buttons. Key ”WWW” n eed to p res s fi rs t. On e w ill hear one “bi” sound when press”WWW” or “Audio” Sound and continuously “bi” sound for another key test. The figure below will be displayed: Press ea[...]

3. Tests and Diagnostics 3.18 Fingerprint DOS Test This test will check if the computer’s Fingerprint function is OK. NOTE: Execution of this test destroys fingerprint data The subtests run step by step: (As below) Step1. Need you swipe your finger to enroll Step2. Need you swipe your finger 2 nd time to enroll. Step3. Need you swipe your finger [...]

3. Tests and Diagnostics Step5. Need you swipe your finger then test program will verify it. Step6. Verify pass, Step7. Need you select your test result to show “PASS” or “Fail”. 3-28 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics 3 . 19 Clear Fingerprint Registered NOTE: Execution of this test destroys fingerprint data Working Instruction: Run command - " HWTEST 0 29 3 1 -C " to clear all information in TBX module The subtests run step by step: (As below) Step1: Step2: Display Notice for clear registered. Step3: below information was the u[...]

3. Tests and Diagnostics Step4: Must to reboot system to make the setting effective. Step5: If you choice “Y”, the system will reboot. If you choice “N”, the system will show Notice again (see be photo). You can press any key to go back test MEMU list. 3-30 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics 3.20 1 st HDD Test The HDD test allows the user to verify the 1 st HDD ok or not. For data security concern, it is necessary to input password - “ hard disk ” before HDD test starts. After the choice HDD test, Screen would display as below: If input password is Right, the screen would display as below: Press any key to [...]

3. Tests and Diagnostics If input password is wrong, the screen would display as below: The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK 3-32 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

3. Tests and Diagnostics If the picture shows as below, it means he HDD function is NG Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-33[...]

3. Tests and Diagnostics 3.21 2 nd HDD Test The HDD test allows the user to verify the 2 nd HDD ok or not. For data security concern, it is necessary to input password - “ hard disk ” before HDD test starts. After the choice HDD test, Screen would display as below: If input password is Right, the screen would display as below: Press any key to [...]

3. Tests and Diagnostics If input password is wrong, the screen would display as below: The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual 3-35[...]

3. Tests and Diagnostics If the picture shows as below, it means he HDD function is NG NOTE : The AC adaptor should be connected to successfully run this test. 3-36 Satellite A130/A135 /Satellite Pro A130 Series Maintenance Manual[...]

[CONFIDENTIAL] Chapter 4 Replacement Procedures[...]

4[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-i Chapter 4 Contents 4.1 General .................................................................................................................... ..... 4-1 4.2 Battery ...............................................................................................................[...]

4 Replacement Procedures 4-ii Satellite A130/ A135 Series Maintenance Manual Figures Figure 4-1 Unlocking th e battery lock .............................................................................4-7 Figure 4-2 Removing the battery pack ............................................................................. 4-7 Figure 4-3 Removing the PC[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-iii Figure 4-30 Removing the optical drive bracket ............................................................. 4-29 Figure 4-31 Removing the strip cover ............................................................................. 4-31 Figure 4-32 Removing the strip cover ........[...]

4 Replacement Procedures 4-iv Satellite A130/ A135 Series Maintenance Manual Figure 4-62 Disconnecting the FFC cable ....................................................................... 4-54 Figure 4-63 Removing the Blue tooth m odule screw ....................................................... 4-54 Figure 4-64 Removing the Bluetooth m odule ..[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-1 4.1 General This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others. Always start[...]

4 Replacement Procedures 4-2 Satellite A130/ A135 Series Maintenance Manual The example below shows FRUs to be removed before the CPU can be rem oved. The CPU is located on the system board, under the VGA module. The system board itself is located under the top cover. The keyboard is on top of the top cover, along with the Bluetooth module, Memory [...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-3 Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1 . Always use the lithium ion battery pack or a backup battery that is authorized by Toshiba or is compatible with the unit. Since other battery [...]

4 Replacement Procedures 4-4 Satellite A130/ A135 Series Maintenance Manual Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassem bly steps. Begin each procedure by removing the AC adaptor and the battery pack as instructed in section 4.2. 1. Do n[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-5 Disassembly Procedures The computer has two basic types of cable connectors:  Pressure Plate Connectors  Standard Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of t[...]

4 Replacement Procedures 4-6 Satellite A130/ A135 Series Maintenance Manual Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The fol[...]

4 Replacement Procedures 4.2 Battery Removing the Battery Pack To remove the battery pack from the battery bay, follow these steps: 1. Turn the computer upside down. 2. Unlock the battery compartment lock. Figure 4-1 Unlocking the battery lock 3. Slide the battery bay latch to release the battery pack and then remove the battery pack from the bay. [...]

4 Replacement Procedures 4-8 Satellite A130/ A135 Series Maintenance Manual Installing the Battery Pack To install the battery pack in the battery bay, follow these steps and refer to the figures in the preceding section. WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only b[...]

4 Replacement Procedures 4.3 PC Card Removing a PC Card To remove a PC card, follow the steps below: 1. Push the PC card’s eject button. The button pops out when you release it. 2. Push the eject button again to pop the PC card out slightly. 3. Grasp the PC card and pull it out from the slot. Figure 4-3 Removing the PC card 4. Press the eject but[...]

4 Replacement Procedures Inserting the PC Card To insert a PC card, follow the steps below: 1. Make sure the eject button does not stick out. Push it back into place if required. 2. Insert the PC card in the slot and gently press to ensure a firm connection. Figure 4-4 Installing the PC card 4-10 Satellite A130/ A135 Series Maintenance Manual[...]

4 Replacement Procedures 4.4 Memory Card Removing a Memory Card To remove a mem ory card, follow the steps below: 1. Press the memory card gently into the socket until it pops out. Figure 4-5 Pressing the memory card 2. Grasp the memory and rem ove it. Figure 4-6 Removing the memory card Satellite A130/ A135 Maintenance Manual 4-11[...]

4 Replacement Procedures Inserting the Memory Card To insert a memory card, follow the steps below: 1. Insert the memory card in the slot and gently press to ensure a firm connection. Figure 4-7 Installing the memory card 4-12 Satellite A130/ A135 Series Maintenance Manual[...]

4 Replacement Procedures 4.5 HDD CAUTION : When handling the HDD, do not press the top surface. Hold the disk by the sides to prevent damage and loss of data. Figure 4-8 HDD Removing the Main HDD Modules The Dual HDD feature make it easy to handle demanding applications while running background applications such as system backup and virus scans. Fo[...]

4 Replacement Procedures 3. Pull up and lift the HDD door to remove it. Figure 4-10 Removing the main HDD door 4. Pull out the black Mylar tab to remove the HDD unit. Figure 4-11 Removing the main HDD 5. Remove the HDD from the HDD case. 4-14 Satellite A130/ A135 Series Maintenance Manual[...]

4 Replacement Procedures 6. Pull the HDD outwards and remove the four M3x3 silver screws that secure the HDD case and bracket to the HDD. Figure 4-12 Removing the HDD screws from bracket Satellite A130/ A135 Maintenance Manual 4-15[...]

4 Replacement Procedures Removing the Second HDD Follow the steps below to remove Main HDD module: 1. Turn the computer upside down. 2. Release the two black M2.5x3 screws to release the secondary HDD door. Secondary HDD Main HDD Figure 4-13 Releasing the secondary HDD door screw 3. Pull up and lift the HDD door to remove it. Figure 4-14 Removing t[...]

4 Replacement Procedures 4. Pull out the black Mylar tab to remove the HDD unit. Figure 4-15 Removing the secondary HDD 5. Remove the HDD from the HDD case. Installing the Main HDD To install the main HDD, follow these steps and refer to the figures in the preceding section. 1. Seat the HDD in the HDD case and bracket, and secure it with four M3 ×[...]

4 Replacement Procedures 4.6 Expansion Memory Removing the Expansion Memory Modules To remove the mem ory module, make sure the computer is in boot m ode before removing the memory m odule. Remove the battery pack, cables and any optional devices before you start and then follow these steps: 1. Release the black non-separate screw M2.5x5.4 screws s[...]

4 Replacement Procedures 3. Push the latches to release the memory m odule. A spring will force one end of the module up. Figure 4-18 Releasing the memory module 4. Grasp the module and pull it out. Figure 4-19 Removing the expansion memory module 5. Repeat steps 3 and 4 to remove the second mem ory expansion module in the same way. CAUTION : Do no[...]

4 Replacement Procedures 4-20 Satellite A130/ A135 Series Maintenance Manual Installing the Expansion Memory Module CAUTION : Do not touch the connectors on the expansion memory module or on the computer. Debris on the connectors may cause memory access problems. Follow these steps to install a memory m odule: 1. Set the computer to boot mode and t[...]

4 Replacement Procedures 4.7 Wireless LAN Unit Removing the Wireless LAN Unit Remove the battery and any optional devices before removing the wireless LAN unit as described in the following instructions. 1. Remove the black non-separate M2.5x5.4 screw securing the wireless LAN door. Figure 4-20 Removing the wireless LAN unit screw 2. Remove the wir[...]

4 Replacement Procedures 3. Remove the wireless LAN module by rem oving the two M2.5x3 screws connecting it to the system board. Figure 4-22 Removing the wireless LAN module screws 4. Detach the two ends of the wireless LAN antenna (black and white). Figure 4-23 Removing the wireless LAN antenna connectors NOTE : The W, B, G markings on logic low i[...]

4 Replacement Procedures 5. Remove the wireless LAN unit. Figure 4-24 Releasing the wireless LAN unit CAUTION : Do not touch the connectors on the wireless LAN unit or on the computer. Debris on the connectors may cause malfunction. Satellite A130/ A135 Maintenance Manual 4-23[...]

4 Replacement Procedures 4-24 Satellite A130/ A135 Series Maintenance Manual Installing the Wireless LAN Unit To install the wireless LAN unit, follow the steps below and refer to the figures in the preceding section. 1. Remove the black non-separate M2.5x5.4 screw securing the wireless LAN door, and then remove the wireless LAN door as described p[...]

4 Replacement Procedures 4.8 Modem Removing the Modem Remove the battery and any optional devices before removing the m odem as described in the following instructions: 1. After removing the WL AN card as described in the previous section, release the two M2.5x3 screws securing the modem m odule. Figure 4-25 Removing the modem module screws 2. Disc[...]

4 Replacement Procedures 3. Carefully lift the unit from its connector. Figure 4-27 Removing the modem module Installing the Modem To install a modem, follow the steps below and refer to the figures in the preceding section. 1. Connect the modem connector on the system board to the modem m odule. 2. Fit the modem onto its connector and secure it wi[...]

4 Replacement Procedures 4.9 Optical Drive Module Removing the Optical Drive Module To remove the optical drive module, you need to rem ove the expansion memory m odule cover first as described in the previous section. Follow the steps below: 1. Turn the computer upside down. 2. Remove the battery and the expansion mem ory module cover. 3. Remove t[...]

4 Replacement Procedures 4-28 Satellite A130/ A135 Series Maintenance Manual Installing the Optical Drive Module To install a device in the optical drive module bay, follow the steps below and refer to the figure in the preceding section. 1. Make sure that the expansion memory door is opened and the ODD screw (M2.5x8, black) is removed. 2. Slide th[...]

4 Replacement Procedures 4.10 Optical Drive This computer may be fitted with a: DVD-ROM device CD-RW/DVD-ROM combo device DVD Super Multi device Disassembling the Optical Drive To disassemble the optical drive, first remove the drive from its module bay as described in the previous section. Next, release the two M2x3 screws from the bracket plate a[...]

4 Replacement Procedures 4-30 Satellite A130/ A135 Series Maintenance Manual Reassembling the Optical Drive NOTE : The small arrow shown on the metal bracket indicates the top side of the optical bracket. Keep this in mind when removing or installing the drive. To reassemble an optical drive, follow the steps below and refer to the figure in the pr[...]

4 Replacement Procedures 4.11 Keyboard Removing the Keyboard Before removing the keyboard, remove the battery and any optional devices. Follow the steps below to remove the keyboard: 1. Open the display panel. 2. Insert a thin tool such as a flat screwdriver into the gap between the strip cover and keyboard to lever the strip cover up. Figure 4-31 [...]

4 Replacement Procedures 4. Remove the two black M2.5x3 black screws securing the keyboard. Figure 4-33 Removing the keyboard screws 5. Push the center of the keyboard, press the center tab, and lift the keyboard out, revealing the keyboard cable underneath. Disconnect the keyboard cable from the system board. Figure 4-34 Disconnecting the keyboard[...]

4 Replacement Procedures 6. Lift and remove the keyboard. Figure 4-35 Removing the keyboard Installing the Keyboard To install the keyboard, follow the steps below and refer to the figures in the preceding section. 1. Connect the keyboard cable to the system board. 2. Place the keyboard on the top cover, insert under the center tab, and secure it w[...]

4 Replacement Procedures 4.12 Display Assembly Removing the Display Assembly To remove the display assembly, first rem ove the battery and any optional devices. Also remove the keyboard, and the wireless LAN unit as described in the previous sections. Then follow the steps below: 1. Separate the wireless LAN antenna connectors (black and white) fro[...]

4 Replacement Procedures 3. Remove four M2.5x8 screws securing the LCD assembly to the top cover Figure 4-37 Removing the front screws 4. Remove two M2.5x8 black screws securing the LCD assembly from the rear side. Figure 4-38 Disconnecting the rear screws Satellite A130/ A135 Maintenance Manual 4-35[...]

4 Replacement Procedures 5. Remove the LCD assembly. Figure 4-39 Removing the display assembly 4-36 Satellite A130/ A135 Series Maintenance Manual[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-37 Installing the Display Assembly To install the display assembly, follow the steps below and refer to the figures in the preceding section. 1. Seat the display assembly, taking care not to crush to the LCD display cable, the LCD power cable, the wireless LAN antenna connectors, or[...]

4 Replacement Procedures 4.13 Display Mask Removing the Display Mask To remove the display mask, first rem ove the display assembly as described earlier, and then follow the steps below: 1. Remove five rubber pads to reveal the five M2.5x6 black screws securing the display mask to the LCD module. Figure 4-40 Removing the rubber pads 2. Remove the f[...]

4 Replacement Procedures 3. Carefully insert your fingers between the display mask and the LCD panel, and pry open the snaps. Start with the four snaps at the top of the display mask. Continue unsnapping the display mask along the two sides and the bottom edge to rem ove the display mask. Figure 4-42 Removing the display mask Installing the Display[...]

4 Replacement Procedures 4.14 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, first remove the battery pack, display assem bly, and display mask; then follow the steps below. 1. Remove the M2x3 black screw securing the FL inverter board to the LCD display assembly. Figure 4-43 Removing the screws 2. Disconnect the [...]

4 Replacement Procedures 3. Remove the FL inverter board. Figure 4-45 Removing the FL inverter board Installing the FL Inverter Board To install the FL inverter board, follow the steps below and refer to the figure in the preceding section. 1. Place the FL inverter board on the LCD module. 2. Secure one M2x3 black screw connecting the FL inverter b[...]

4 Replacement Procedures 4.15 LCD Module Removing the LCD Module To remove the LCD module, first rem ove the display assembly, display mask, and FL inverter board and then follow the steps below. 1. Lift the LCD module from the top chassis. Figure 4-46 Removing the LCD Module 2. Remove six M2x3 screws securing the LCD module bracket to the LCD m od[...]

4 Replacement Procedures 3. Turn over the LCD screen and remove the tape securing the LVDS cable. Detach the LVDS cable. Figure 4-48 Removing the LVDS cable Installing the LCD Module To install the LCD module, follow the steps below and refer to the figures in the preceding section. 1. Secure the LVDS cable to the LCD module. 2. Seat the LCD module[...]

4 Replacement Procedures 4.16 Bluetooth and WLAN antennas To remove the Bluetooth and WLAN antennas, first rem ove the display assembly, display mask, FL inverter board and the LCD display module. Then follow the steps below. 1. Remove the four square tabs securing the Bluetooth and WLAN antennas. Figure 4-49 Removing the Bluetooth and WLAN antenna[...]

4 Replacement Procedures 4.17 Top Cover Removing the Cover To remove the top cover, first remove the battery pack, HDD, expansion m emory module, ODD, modem, wireless LAN unit, keyboard, and display assem bly, and then disconnect the black LCD power (LVDS) cable, Bluetooth cable, and wireless LAN cable from the system board, as described in the pre[...]

4 Replacement Procedures 2. Turn the computer over again and detach the two speaker cables, touch pad FFC cable, finger print unit FFC cable, and the Function Button cable from the top cover. Figure 4-51 Removing the cables 3. Remove the three M2.5x6 black screws securing the top cover. Figure 4-52 Removing the top cover (front panel screws) 4-46 S[...]

4 Replacement Procedures 4. Lift off the top cover. Figure 4-53 Removing the top cover Installing the Top Cover To install the top cover, follow the steps below and refer to the figures in the preceding section. 1. Seat the top cover, and secure the speaker cables, finger print unit FFC cable, touch pad unit FFC cable, and the Function Button cable[...]

4 Replacement Procedures 4.18 Function Button Board Removing the Function Button Board To disassemble the function button board, first remove the battery, optional devices, and the keyboard strip cover. Then follow the steps below. 1. Insert a thin tool such as a flat screwdriver into the gap between the frame and the Function Button Board to lever[...]

4 Replacement Procedures 3. Use a thin object such as a screwdriver to press the release button on the Function Button Board and lift it up Figure 4-56 Removing the Direct Play Button Board Installing the Function Button Board To install the Function Button Board, follow the steps below and refer to the figures in the preceding section. 1. Snap the[...]

4 Replacement Procedures 4.19 Fingerprint Module Removing the Fingerprint Module To remove the Fingerprint Module, first remove the battery pack, keyboard, and top cover, and then follow the steps below: 1. Remove four M2.0x2.3 black screws securing the Fingerprint Module Bracket to the rear side of the top cover. Figure 4-57 Removing the fingerpri[...]

4 Replacement Procedures 3. Remove the Fingerprint module by lifting it gently. Figure 4-59 Removing the fingerprint module Installing the Fingerprint Module To install the Fingerprint Module, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the Fingerprint Module and the Fingerpr[...]

4 Replacement Procedures 4.20 Touch Pad Removing the Touch Pad To remove the Touch Pad, first remove the battery pack, keyboard, top cover, and Fingerprint module, and then follow the steps below: 1. Remove five M2.5x3 screws securing the Touch Pad Bracket to the rear side of the top cover. Figure 4-60 Removing the touch pad screw 2. Remove the Tou[...]

4 Replacement Procedures Satellite A130/ A135 Maintenance Manual 4-53 Installing the Touch Pad To install the Touch Pad, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the Touch Pad and the Touch Pad Bracket in position on top. 2. Secure the Touch Pad bracket with five M2.5x3 sc[...]

4 Replacement Procedures 4.21 Bluetooth module Removing the Bluetooth Module Remove the battery and any optional devices before removing the Bluetooth m odule. In addition, you have to remove the keyboard as described in the previous section to access the Bluetooth module. Follow these instructions: 1. Disconnect the Bluetooth FFC cable from the sy[...]

4 Replacement Procedures 3. Gently lift the Bluetooth module. Figure 4-64 Removing the Bluetooth module 4. Separate the FFC cable from the Bluetooth module. Figure 4-65 Removing the Bluetooth module cable Installing the Bluetooth Module To install the Bluetooth module, follow the steps below and refer to the figures in the preceding section. 1. Sec[...]

4 Replacement Procedures 4.22 Speakers Removing the Speakers Remove the battery pack, cables and any optional devices before you start. In addition, remove the keyboard and the top cover and then follow these steps: 1. Remove the two M2.5x5 screws securing the left speaker to the rear side of the top cover. Remove the two M2.5x5 screws securing the[...]

4 Replacement Procedures 3. Remove the speaker brackets. Figure 4-68 Removing the speaker brackets Installing the Speakers To install the speakers, follow the steps below and refer to the figures in the preceding section. 1. Seat the speaker brackets in the top cover paying attention to the direction markings. 2. Replace the speakers and secure wit[...]

4 Replacement Procedures 4.23 USB Board Removing the USB Board To remove the USB board, first remove the battery pack, keyboard, and top cover, and then follow the steps below: 1. Remove the M2.5x3 screw securing the USB board to the system board. Figure 4-69 Removing the USB Board screws 2. Remove the USB board cable. Figure 4-70 Removing the USB [...]

4 Replacement Procedures 3. Remove the USB board. Figure 4-71 Removing the USB Board Installing the USB Board To install the USB board, follow the steps below and refer to the figures in the preceding section: 1. Place the USB board in position next to the system board. 2. Connect the USB board cable to the system board. 3. Secure the USB board wit[...]

4 Replacement Procedures 4.24 System Board Removing the System Board To remove the system board, first rem ove the display assembly, keyboard, and top cover, and then follow the steps below: 1. Remove the two M2.5x6 screws and two M2.5x3 screws securing the system board. Then remove the two hexagonal VGA screws from the system board. M2.5x 6 screws[...]

4 Replacement Procedures 3. Remove the system board after m aking sure that all connectors are removed from their respective sockets. Figure 4-74 Removing the system board Installing the System Board To install the system board, follow the steps below and refer to the figures in the preceding section. 1. Seat the system board in the chassis. Take c[...]

4 Replacement Procedures 4.25 VGA Module Removing the VGA Module To remove the VGA module, you have to first rem ove the keyboard, top cover, and system board. Then follow the steps below: 1. Turn the system board over and remove the three M2.5x3 screws securing the VGA bracket. Figure 4-75 Removing the VGA module screws 2. Remove the VGA module fr[...]

4 Replacement Procedures 3. Remove the heat sink from the VGA m odule by removing the four M2.5x3 screws. Follow the order indicated by the numbers on the heat sink to remove the screws. Figure 4-77 Removing the VGA module heat sink Installing the VGA Module To install the VGA module, follow the steps below and refer to the figure in the preceding [...]

4 Replacement Procedures 4.26 Fan & CPU Removing the Fan & CPU To remove the fan, heat sink, and CPU, you must first rem ove the display assembly, keyboard, top cover and system board, and then follow the steps below: 1. Turn the system board upside down. Remove the four M2.5x6 screws from the heat sink. Figure 4-78 Removing the heat sink s[...]

4 Replacement Procedures 3. Turn over and remove the fan connector from the system board. Figure 4-80 Removing the fan connector 4. Remove the M2.5x3 screw securing the fan from the top side of the system board. Figure 4-81 Removing the fan screw from the top side of the system board Satellite A130/ A135 Maintenance Manual 4-65[...]

4 Replacement Procedures 5. Remove the fan module. Figure 4-82 Removing the fan 6. Turn the cam on the CPU socket with a flat-blade screwdriver so that the notch on the cam is aligned with the open side of the CPU socket to unlock the CPU. Figure 4-83 Turning the CPU cam 4-66 Satellite A130/ A135 Series Maintenance Manual[...]

4 Replacement Procedures 7. Gently lift out the CPU. Figure 4-84 Removing the CPU Satellite A130/ A135 Maintenance Manual 4-67[...]

4 Replacement Procedures 4-68 Satellite A130/ A135 Series Maintenance Manual Installing the CPU To install the CPU, follow the steps below and refer to the figures in the preceding section. CAUTION: If you remove the heat sink, use the CPU grease tool to remove the grease on the CPU and heat sink. Reapply fresh grease before installing the heat sin[...]

Appendices [CONFIDENTIAL][...]

Appendices App-ii [CONFIDENTIAL] S atellite A130/ A135 Series Maintenance Manual[...]

Appendix Contents Appendix A Handling the LCD Module ............................................................................... A-1 Appendix B Board Layout ..................................................................................................... B-1 B.1 System Board (FRDSY*) Top View ................................................[...]

Appendices App-iv [CONFIDENTIAL] Satellite A130/ A135 Series Main tenance Manual C.25 J18 VGA/B I/F (200-pin) .............................................................................................. C-21 Appendix D Keyboard Scan/Character Codes..................................................................... D-1 Appendix E Key Layout ....[...]

E.27 Danish (DM) Keyboard ................................................................................................. E-14 E.28 Slovak (SV) Keyboard ................................................................................................... E-14 E.29 Swedish (SD) Keyboard ...............................................................[...]

Appendices App-vi [CONFIDENTIAL] Satellite A130/ A135 Series Main tenance Manual Figures Figure B-1 System board (F RDSY*) layout (Top) ............................................................... B-1 Figure B.2 System board (FRDSY*) layout (Bottom) .......................................................... B-2 Figure E-1 US keyboard ...........[...]

Figure E-28 SV keyboard....................................................................................................... E -14 Figure E-29 SD keyboard....................................................................................................... E -15 Satellite A130/ A135 Series Main tenance Manual [CONFIDENTIAL] App-vii[...]

Appendices App-viii [CONFIDENTIAL] Satellite A130/ A135 Series Maintenance Manual Tables Table B-1 System board ICs (top and bottom) ..................................................................... B-3 Table B-2 System board connectors (top and bottom) ......................................................... B-4 Table C-1 SODIMM I/F pin a ssi[...]

Table D-2 Scan codes with left Shift key ............................................................................. D-5 Table D-3 Scan codes in Numlock mode ............................................................................. D-6 Table D-4 Scan codes with Fn key............................................................................[...]

Appendices App-x [CONFIDENTIAL] Satellite A130/ A135 Series Main tenance Manual[...]

Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assem bly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assem bly, make sure that you seat it so that it is properly aligned a[...]

3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly [...]

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module. Satellite A130/ A135 Seri es Maintenance Manu[...]

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassem bly can cause malfunctions. A-4 [CONFIDENTIAL][...]

10. If you transport the module, do not use packing material that contains epoxy resin (am ine) or silicon glue (alcohol or oxime). These materials can release gas that can dam age the panel’s polarization. Satellite A130/ A135 Seri es Maintenance Manual [CONFIDENTIAL] A-5[...]

A-6 [CONFIDENTIAL] Satellite A130/ A135 Seri es Maintenance Manual[...]

Appendix B Appendix B Board Layout B.1 System Board (FRDSY*) T op V iew U13 JP21 JP8 JP34 U22 U9 U6 U38 JP1 JP4 JP5 JP32 JP6 JP7 JP2 JP3 JP33 Satellite A130/ 135 Series Maintenance Manual [CONFIDENTIAL] 1[...]

B.2 System Board (FRDSY*) Button V iew JP11 JP12 PJP2 U30 JP14 JP13 PJP1 U5 JP15 JP16 JP18 JP19 JP20 JP20 JP17 JP24 JP25 JP9 U16 JP31 JP10 JP28 JP29 Satellite A130/ 135 Series Maintenance Manual [CONFIDENTIAL] 2[...]

T able B-1 System board connectors (top and bottom ) Number Name JP1 LCD conn JP2 Speaker conn (Right) JP3 SW/LED conn JP4 F AN conn JP5 TP conn JP6 Keyboard conn JP7 Bluetooth conn JP8 PCMCIA Socket JP9 1st SA T A HDD conn JP10 6 in 1 CardReader conn JP1 1 LAN conn JP12 USB conn1 (Back Side) JP13 CR T conn JP14 VGA/B con n JP15,16 DDR2 conn JP17 T[...]

T able B-2 System board ICs (top and bottom ) Number Name U5 LAN R TL8101E/ R TL81 11B U6 North bridge 945GM/945PM U9 Clock Generator ICS9LPRS325CKLFT U13 EC KB910 U16 South bridge ICH7 U22 BIOS ROM U30 LAN transformer U31 Card bus controller TI P CI7412 U38 HD codec AC861-VD-GR Satellite A130/ 135 Series Maintenance Manual [CONFIDENTIAL] 4[...]

C. Appendix C Pin Assignments System Board C.1 JP15,JP16 Table C-1 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 VREF O 2 VSS O 3 VSS O 4 DQ4 I/O 5 DQ0 I/O 6 DQ5 I/O 7 DQ1 I/O 8 VSS O 9 VSS O 10 DM0 I/O 11 DQS0# I/O 12 VSS O 13 DQS0 I/O 14 DQ6 I/O 15 VSS O 16 DQ7 I/O 17 DQ2 I/O 18 VSS O 19 DQ3 I/O 20 D[...]

Table C-1 SODIMM I/F pin assignments (200-PIN) (2/4) Pin No. Signal name I/O Pin No. Signal Name I/O 51 DQS2 I/O 52 DM2 I/O 53 VSS O 54 VSS O 55 DQ18 I/O 56 DQ22 I/O 57 DQ19 I/O 58 DQ23 I/O 59 VSS O 60 VSS O 61 DQ24 I/O 62 DQ28 I/O 63 DQ25 I/O 64 DQ29 I/O 65 VSS O 66 VSS O 67 DM3 I/O 68 DQS3# I/O 69 NC - 70 DQS3 I/O 71 VSS O 72 VSS O 73 DQ26 I/O 74[...]

Table C-1 SODIMM I/F pin assignments (200-PIN) (3/4) Pin No. Signal name I/O Pin No. Signal Name I/O 115 NC/S1# I/O 116 NC/A13 I/O 117 VDD O 118 VDD O 119 NC/ODT1 I/O 120 NC - 121 VSS O 122 VSS O 123 DQ32 I/O 124 DQ36 I/O 125 DQ33 I/O 126 DQ37 I/O 127 VSS O 128 VSS O 129 DQS4# I/O 130 DM4 I/O 131 DQS4 I/O 132 VSS O 133 VSS O 134 DQ38 I/O 135 DQ34 I[...]

Table C-1 SODIMM I/F pin assignments (200-PIN) (4/4) Pin No. Signal name I/O Pin No. Signal Name I/O 181 DQ57 I/O 182 DQ61 I/O 183 VSS O 184 VSS O 185 DM7 I/O 186 DQS7# I/O 187 VSS O 188 DQS7 I/O 189 DQ58 I/O 190 VSS O 191 DQ59 I/O 192 DQ62 I/O 193 VSS O 194 DQ63 I/O 195 SDA I/O 196 VSS O 197 SLC I/O 198 SA0 O 199 VDDSPD O 200 SA1 O C-4 [CONFIDENTI[...]

C.2 JP13 Table C-2 RGB I/F pin assignments (15-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 CRT_R_L O 2 CRT_G_L O 3 CRT_B_L O 4 GND - 5 GND - 6 GND - 7 GND - 8 GND - 9 +CRT_VCC - 10 GND - 11 NC - 12 DSUB_12 I/O 13 CRT_HSYNC_L O 14 CRT_VSYNC_L O 15 DSUB_15 I/O Satellite A130/ A135 Series Mainte nance Manual [CONFIDENTIAL] C-5[...]

C.3 JP22 Table C-3 1st HDD I/F pin assignments (22-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND 2 A+ 3 A- 4 GND 5 B- 6 B+ 7 GND 8 VCC3.3 9 VCC3.3 10 VCC3.3 11 GND 12 GND 13 GND 14 VCC5 15 VCC5 16 VCC5 17 GND 18 NC 19 GND 20 NC 21 NC 22 NC - C.4 JP31 Table C-4 2nd HDD I/F pin assignments (22-pin) Pin No. Signal name I/O Pin No. Signal [...]

C.5 JP19 Table C-5 ODD I/F pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 INT_CD_L I 2 INT_CD_R I 3 CD_AGND - 4 NC - 5 IDE_ODDRST# O 6 IDE_DD8 I/O 7 IDE_DD7 I/O 8 IDE_DD9 I/O 9 IDE_DD6 I/O 10 IDE_DD10 I/O 11 IDE_DD5 I/O 12 IDE_DD11 I/O 13 IDE_DD4 I/O 14 IDE_DD12 I/O 15 IDE_DD3 I/O 16 IDE_DD13 I/O 17 IDE_DD2 I/O 18 IDE_DD[...]

C.6 JP8 Table C-6 PC Card I/F pin assignments (68-pin) (1/2) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND - 35 GND - 2 DATA3 I/O 36 CD1# O 3 DATA4 I/O 37 DATA11 I/O 4 DATA5 I/O 38 DATA12 I/O 5 DATA6 I/O 39 DATA13 I/O 6 DATA7 I/O 40 DATA14 I/O 7 CE1# I/O 41 DATA15 I/O 8 ADD10 I 42 CE2# I/O 9 OE# I/O 43 VS1# I 10 ADD11 I 44 IORD# I/O 11 ADD9[...]

Table C-6 PC Card I/F pin assignments (68-pin) (2/2) Pin No. Signal name I/O Pin No. Signal Name I/O 31 DATA1 I/O 65 DATA9 I/O 32 DATA2 I/O 66 DATA10 I/O 33 WP I/O 67 CD2# I 34 GND - 68 GND - Satellite A130/ A135 Series Mainte nance Manual [CONFIDENTIAL] C-9[...]

C.6 JP24 Table C-6 Mini-Express I I/F pin assignments (54-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 PCI_WAKE I/O 2 +3VS O 3 WLAN_DATA I/O 4 VSS 5 WLAN_CLK I/O 6 +1.5VS O 7 MINI_CLKREQ I/O 8 NC - 9 VSS - 10 NC - 11 CLK_PCIE# I/O 12 NC - 13 CLK_PCIE I/O 14 NC - 15 VSS - 16 NC - 17 NC - 18 VSS - 19 NC - 20 XMIT_OFF# I/O 21 VSS - 22 PLT_RS[...]

C.7 JP1 Table C-7 LCDS I/F (30-pin) Pin No. Signal name Function 1 GND GND 2 GND GND 3 TXCLK- Panel Clock Signals 4 GND GND 5 TXCLK+ Panel Clock Signals 6 NC Non-Connection 7 GND GND 8 +LCDVDD_LCD Power for Panel 9 TXOUT0- Panel Data Signals 10 +VCDVDD_LCD Power for Panel 11 TXOUT0+ Panel Data Signals 12 +3VS_LCD Power for Panel 13 GND GND 14 +3VS_[...]

C.8 JP4 Table C-8 JP8 Fan I/F pin assignments (3-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +FAN1_VOUT I 2 FANSPEED1 O 3 GND - C9 JP6 Table C-9 K/B connector pin assignments (38-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 +3VS I 2 NC - 3 5 7 9 11 13 15 17 19 21 23 25 NC NC KSO4 KSI2 KSO1 KSI0 KSO5 KSI5 KSI4 KSO7 KSI7 KSO9 - -[...]

C.10 JP25 Table C-10 MDC Connector pin assignments (12-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 GND - 2 REV - 3 ACZ_SDOUT O 4 REV - 5 GND - 6 3.3V O 7 ACZ_SYNC I/O 8 GND - 9 ACZ_SDIN1 I/O 10 GND - 11 REEST I/O 12 ACZ_BITCLK I/O C.1 1 PJP1 Table C-119 AC Adaptor Connector pin assignments (4-pin) Pin No. Signal name I/O Pin No. Signal N[...]

Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06 86 2E F0 2E 07 6 ^ 07 87 36 F0 36 08 7 & 08 88 3D F0 3D *2 09 8[...]

Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34 36 H 23 A3 33 F0 33 37 J 24 A4 3B F0 3B *2 38 K 25 A5 42 F0 42 *2 39 L 26 A6 4B F0 4B *2[...]

Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl(L) 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 64 Ctrl(R) E0 1D E0 9D E0 14 E0 F0 14 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *1 76 Del E0 53 E0 D3 E0 71 E0 F0 71 *1 79 ← E0[...]

Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Notes: 1. * Scan codes differ by mode. 2. * Sca[...]

Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79 ← E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12 80 Home[...]

Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 80 Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12 81 End E[...]

Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E [...]

Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Common E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes. D-8 [CONFIDENTIAL] Satellite A130/ A135 Se ries Maintenance Manual[...]

Appendix E Key Layout (GS) United Kingdom (UK) Keyboard Figure UK keyboa r d S p anish (SP) Keyboard Figure SP keyboard[...]

Portuguese (PO) Keyboard Figure PO keyboardE.8 US-INTE (UI/INTE) Keyboard Figure US-INT E Key boa rd[...]

Germanic (GR) Keyboard Figure GR keyboard France (FR) Keyboard Figure FR keyboard[...]

It alian (IT) Keyboard Figure IT keyboard Belgium (BE) Keyboard Figure BE keyboard[...]

Czech (CZ) Keyboard Figure CZ keyboard Greek (GK) Keyboard Figure GK keyboard[...]

Hebrew (HB) Keyboard Figure HB keyboard Hungary (HG) Keyboard Figure HG Keyboard[...]

Norwegian (NW) Keyboard Figure NW keyboard Russian (RU) Keyboard Figure RU keyboard[...]

T urkish (TR) Keyboard Figure TR keyboard Y ugoslavian (YU) Keyboard Figure YU keyboard[...]

Danish (DM) Keyboard Figure DM keyboard Swedish (SD) Keyboard Figure SD keyboard[...]

Swiss (SW) Keyboard Figure SW keyboard Arabic (ARE) Keyboard Figure ARE keyboard[...]

Slovakian (SV) Keyboard Figure SV keyboard T urkish-F (TR) Keyboard Figure TR –F keyboard[...]

Scandinavian (ND) Keyboard Figure ND keyboard[...]

F. Appendix F Series Screw Torque List Table F-1 Series Screw Torque List SCREW P/N SCREW SPEC Q'ty LOCATION SCREW TORQUE 8 LCD HINGE BRK ASSY L&R TO LCD 15.4w" 1.2~1.5Kgf.cm MA0000060G0 M2.0*3 1 INVERTER TO COVER SUB ASSY 1.5~2.0Kgf.cm MA0000062G0 M2.5*6 5 LCD BEZEL TO COVER 2.5~3.0Kgf.cm 1 THERMAL FAN TO MB 2.0~2.5Kgf.cm 2 MINICARD [...]

1 LOG LOW TO LOG UP/L (FRONT) 2.5~3.0Kgf.cm 2 LCD HINGE BRK R-LOG UP-HINGE SADDLE R 4.0~4.5Kgf.cm 2 LCD HINGE BRK L-LOG UP-HINGE SADDLE L 4.0~4.5Kgf.cm 2 THERMAL FAN-LOG LOW 2.5~3.0Kgf.cm 2 LOG LOW TO SADDLE (R/L) 2.5~3.0Kgf.cm 1 LOG LOW-USB PCB TO LOG UP 2.5~3.0Kgf.cm 2 LOG LOW TO SADDLE TO LOG UP 2.5~3.0Kgf.cm 2 LOG LOW TO MB TO LOG UP (M)- NEAR [...]

Appendix G Appendix G Reliability The followin g table shows MT BF (Mean Tim e Between Failures) for each com ponent. Table G-1 MTBF Component Time (hours) LCD 10,000 Keyboard 60,000 HDD 300,000 Removable FDD 30,000 Optical (DVD/CD) drive 60,000 AC adaptor 60,000 Satellite A130/ 135 Series Mainten ance Manual [CONFIDENTIAL] G-1[...]