TP-Link TL-WR702N Bedienungsanleitung

TL-WR702N 150Mbps Wireless N Nano Router Rev: 1.0.0 1910010547[...]

- I - COPYRIGHT & TRADEMARKS S pecifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other br ands and product names are trademarks or registered trademarks of t heir respective holders. No part of th e specifications ma y be reproduced in any form or by any means or used to make any d[...]

- II - FCC RF Radiation Exposure S t atement This equipment complies with FCC RF radiatio n exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co -located or operating in conjunction with any other antenna or transmitter . “T o comply with FCC RF exposure compliance r equirements, this grant is appl[...]

TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD . South Building, No.5 Keyuan Road, Central Zone, Science & T echnology Park, Nanshan, Shenzhen, P . R. China DE CLARA TION OF C ONF ORMITY For the following equipment: Product Description: 150Mbp s Wireless N Nano Router Model No.: TL-WR702N T rademark: TP-LINK We declare under our [...]

- I - CONTENTS Package Co ntent s............................................................................................................... ................... 1 Chapter 1. Introduc tion ................................................................................................................... .... 2 1.1 Overview of the Ro uter .......[...]

- II - 5.12 IP & MAC Bind ing Setting ................................................................................................ 94 5.13 Dynamic DNS................................................................................................................... 96 5.14 System T ools ......................................................[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 - Package Contents The following items should be found in your package: ¾ One TL-WR702N 150Mbps Wireless N Nano Router ¾ Quick Install ation Guide ¾ One Power Adapter ¾ One USB Cable ¾ One RJ-45 Ethernet Cable ¾ One Resource CD for TL-WR702N 150Mbps Wireless N Nano Router , including: • User Guid[...]

TL-WR702N 150Mbps Wireless N Nano Router - 2 - Chapter 1. Introduction Thank you for choosing the TL-WR7 02N 150Mbps Wireless N Nano Router . 1.1 Overview of the Router Small enough to fit in the average pocket, the TL-WR702N 150Mbps Wireless N Nano Router is uniquely suited to provide robust wireless network i ng to travelers, students, or anyone [...]

TL-WR702N 150Mbps Wireless N Nano Router - 3 - this user guide. Before installing the Router , please look through this guide to know all the Router ’s functions. 1.2 Conventions The Router o r TL-WR 702N me ntione d in this guide s tand s for TL-WR702N 1 5 0 M b ps W i r e l es s N N ano Router without any explanation. Parameters provided in the[...]

TL-WR702N 150Mbps Wireless N Nano Router - 4 - 1.4 Panel Layout Figure 1-1 T L-WR702N sketch ¾ LED Statu s Indication Solid It’s powered on but the LA N/W AN port is not connected. Flashing Slowly The LAN/W AN cable is connected but there is no data being transmitted or received. Flashing Quickly The LAN/W AN cable is connec ted and there is dat[...]

TL-WR702N 150Mbps Wireless N Nano Router - 5 - Chapter 2. Connecting the Router 2.1 System Requirement s ¾ Each PC in the LAN needs a working Ethernet Adapter ¾ TCP/IP protocol must be inst alled on each PC ¾ Web browser , such as Microsoft Internet Explorer 5.0 or later , Mozilla Firefox, Apple Safari ¾ If the device is configured to AP router[...]

TL-WR702N 150Mbps Wireless N Nano Router - 6 - 2.3.1 AP Mode As the supplement of wi red LAN, TL-WR702N enables the wir ed LAN to connect to the Internet wirelessly . The default mode of TL-WR702N is AP . Plug the pow er plug of TL-WR702N in electrical wall socket and connect the Ethernet cabl e correctly , you can surf the Internet by connecting y[...]

TL-WR702N 150Mbps Wireless N Nano Router - 7 - Figure 2-2 Hardware Installation of the TL-WR702N in Router Mode 1. Connect the W AN port of TL-WR702N to the LAN Port on the DSL/Cable Modem. 2. Connect the W AN port on the DSL/C able Modem to the wired Internet. 3. Plug the power plug of TL-WR7 02N in electrical wall socket. 4. Power on the DSL/Cabl[...]

TL-WR702N 150Mbps Wireless N Nano Router - 8 - ) Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to se t the Router in AP Repeater mode. 2.3.4 Bridge Mode Similar to the Bridge mode, TL-WR702N in Brid ge mode is also used to extend the range [...]

TL-WR702N 150Mbps Wireless N Nano Router - 9 - Figure 2-5 Hardware Installation of the TL-WR702N in Client Mode 1. Connect the PC to the LAN/W AN port of TL-WR702N router with an Ethernet cable. 2. Plug the power plug of TL-WR7 02N in electrical wall socket. 3. Power on the PC(s). ) Note: TL-WR702N can be powered by external power ada pter or USB c[...]

TL-WR702N 150Mbps Wireless N Nano Router - 10 - Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functi ons of your TL-WR702N 150Mbps Wireless N Nano Router using Quick Setup Wi za rd within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR702N 150Mbps Wireless N Nano Router is 192.168.0.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 1 - Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2, it means the connection between your P C and the Router has failed. Figure 3-2 Failure result of Ping command Please check the connection following these step s: 1. Is the connection bet ween your PC an[...]

TL-WR702N 150Mbps Wireless N Nano Router - 12 - 3.2 Quick Inst allation Guide With a Web-based utility , it is easy to configure and manage the TL-WR702N 150Mbps Wireless N Nano Router . The Web-based ut ility can be used on any Windows, Macintosh or UNIX OS with a Web browser , such as Microsoft In ternet Explorer , Mozilla Firefox or Apple Safari[...]

TL-WR702N 150Mbps Wireless N Nano Router - 13 - 3. Click Next , and then Working Mode p age will appear , shown in Figure 3-5. Figure 3-5 Quick Setup - W orking Mode ) Note: The Router supports five worki ng modes for multi-user to acce ss the Internet: AP, Router, Repeater, Bridge and Client. In AP mode, TL-WR 702N enables the wired LAN to connect[...]

TL-WR702N 150Mbps Wireless N Nano Router - 14 - Figure 3-6 Quick Setup - Wireless AP ¾ Wireless Radio - Enable or disable the wireless radi o choosing from the pull-down list. ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wire less devices in your network. The default SS[...]

TL-WR702N 150Mbps Wireless N Nano Router - 15 - • 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. • 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode. When 802. 11g mode is selected, only 802.11g wireless stations can connect to the R outer. Wh[...]

TL-WR702N 150Mbps Wireless N Nano Router - 16 - Figure 3-8 Quick Setup – Finish 3.2.2 Router Mode When you choose Router on Working Mode p age in Figure 3-5 , take the following steps: 1. Click Next in Figure 3-5 , and you will see the followi ng scree n. The wireless settings on Router mode are the same as that on AP mode. Figure 3-9 Quick Setup[...]

TL-WR702N 150Mbps Wireless N Nano Router - 17 - Figure 3-10 Quick Set up - WAN Connection Type The Router supports three popular ways PPPoE , Dynamic IP and Static IP to connect to the Internet. T o make sure the connection type your IS P provides, please refer to the ISP . Make sure the cable is securely plugged in to the W AN port before detectio[...]

TL-WR702N 150Mbps Wireless N Nano Router - 18 - Figure 3-12 Quick Setup - S tatic IP 3. Click Next , you will see the Finish page as shown in Figure 3-13. Click the Reboot button to make your wireless configuration take ef fect and finish the Quick Setup. Figure 3-13 Quick Setup – Finish 3.2.3 Repeater Mode When you choose Repeater Mode on Workin[...]

TL-WR702N 150Mbps Wireless N Nano Router - 19 - Figure 3-14 Quick Setup - Wireless Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. I[...]

TL-WR702N 150Mbps Wireless N Nano Router - 20 - Figure 3-15 AP List ) Note: If you know the SSID of the desired AP , you can al so input it into the field "SSID" manually . 2. Click the Next button in Figure 3-14. Y ou will then see the Fin ish page. Because something has changed on the Wireless Repeater page, you will see the Finis h pag[...]

TL-WR702N 150Mbps Wireless N Nano Router - 21 - Figure 3-16 Quick Setup - Finish 3.2.4 Bridge Mode When you choose Bridge on Working Mode p age in Figure 3-5 , take the following steps: 1. Click Next , and then Wireless Repeater page will appear as shown in Figure 3-17. Figure 3-17 Quick Setup - Wireless Bridge ¾ SSID - Enter a string of up to 32 [...]

TL-WR702N 150Mbps Wireless N Nano Router - 22 - ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not li[...]

TL-WR702N 150Mbps Wireless N Nano Router - 23 - ¾ PassWord - If the AP your Router is going to co nnect needs password, you need to fill the password in this blank. Click Survey button on the Wireless page as sh own in Figure 3-17, and then AP List page will appear as shown in Figure 3-18. Find the SSID of the Access Point you wan t to acce ss, an[...]

TL-WR702N 150Mbps Wireless N Nano Router - 24 - Figure 3-19 Quick Setup - Wireless Security Settings This page is for setting wireless security of y our ow n AP . When computers and mobile phones are connected to the AP , they s hould input the same password. ¾ Disable Security - The wireless security function can be enabled or disabled. If disabl[...]

TL-WR702N 150Mbps Wireless N Nano Router - 25 - Figure 3-21 Quick Setup - Wireless Client ¾ SSID - Enter the SSID that you want to access. ¾ MAC of AP - Enter the MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 26 - Figure 3-22 AP List 3. Click the Next button in Figure 3-23. Y ou will then see the Fin ish page. Click the Reboot button to make your wireless configurati on take ef fect and finish the Quick Setup. Figure 3-23 Quick Setup - Finish[...]

TL-WR702N 150Mbps Wireless N Nano Router - 27 - ) Note: 1. The operating distance or range of your wire less connection varies si gnificantly based on the physical placement of the Router . Fo r best results, place your Router . z Near the center of the area in which your wireless stations will operate. z In an elevated location such as a high shel[...]

TL-WR702N 150Mbps Wireless N Nano Router - 28 - Chapter 4. Configuration for AP Mode This chapter will show each Web p age's key f unctions and the configurat ion way for AP Mode of TL-WR702N. 4.1 Login After your successful login, you can configur e and manage the device. T here are main menus on the left of the web-based utility . Submenus w[...]

TL-WR702N 150Mbps Wireless N Nano Router - 29 - Figure 4-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware. ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 30 - • Channel Wid th - The current wireless channel width in use. • MAC address - The physical address of the Router , as seen from the WLAN. • WDS St atus - The status of WDS connection. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset. Click the Refresh bu[...]

TL-WR702N 150Mbps Wireless N Nano Router - 31 - Figure 4-4 4.5 Network Figure 4-5 the Network menu There is only one submenu under the Network menu (shown in Figure 4-5): LAN . 4.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 4-6 LAN ¾ MAC Address - The physica[...]

TL-WR702N 150Mbps Wireless N Nano Router - 32 - 4.6 Wireless Figure 4-7 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-7): Wireless Settings , Wireless Security , MAC Filtering, W ireless Ad vanced and Wireless St atistics. Click any of them, and you will be able to confi gure the corresponding function. 4.6.1 Wire[...]

TL-WR702N 150Mbps Wireless N Nano Router - 33 - name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test . ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. It may be illegal to use the wireless function of[...]

TL-WR702N 150Mbps Wireless N Nano Router - 34 - ¾ SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search func tion to select the SSID to join. ¾ BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client. You can also use the search func tion to select [...]

TL-WR702N 150Mbps Wireless N Nano Router - 35 - 2. Failure to follow these gui delines can result in significant performance degradation or inabi lity to wirelessly connect to the Router . 4.6.2 Wireless Security Choose menu “ Wi rel es s → Wireless Security ”, and then you can configure the security settings of your wireless network. There a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 36 - • Typ e - you can choose the type for the WEP se curity on the pull-down list. The default setting is Automatic , which can select Shared Key or Open System authentication type automatically based on the wirele ss station's capability and request. • WEP Key Format - Hexadecimal and ASCII form[...]

TL-WR702N 150Mbps Wireless N Nano Router - 37 - key of WPA) or WP A2-PSK (Pre-shared key of WPA) autom atically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authenticat ion Type, you can select Automatic (Recommended) , TKIP or AES as Encryption. • PSK Password - You can enter ASC[...]

TL-WR702N 150Mbps Wireless N Nano Router - 38 - ¾ Description - A simple description of the wireless station. To Add a Wireless MAC Addre ss filtering entry, click the Add N ew … button. The " Add or Modify Wireless MAC Address Filtering entr y " page will appear , shown in Figure 4-1 1: Figure 4-1 1 Add or Modify Wire less MA C Addres[...]

TL-WR702N 150Mbps Wireless N Nano Router - 39 - 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specifi ed by any enabled entries in the list to access” for Filtering Rules . 3. Delete all or disable all entries if there are an y entries already. 4. Click the Add New... button. • Enter the MA[...]

TL-WR702N 150Mbps Wireless N Nano Router - 40 - ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000 millise conds for Beacon Interval here. The beacons are the packets sent by[...]

TL-WR702N 150Mbps Wireless N Nano Router - 41 - Figure 4-13 Wireless S tatistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless stat ion's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WP A-PSK / WPA 2 / WPA2-PSK / AP-UP / A P-DOWN / Disconnected ¾ Received Pack[...]

TL-WR702N 150Mbps Wireless N Nano Router - 42 - Figure 4-15 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to st art with when as[...]

TL-WR702N 150Mbps Wireless N Nano Router - 43 - 4.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in the screen as shown in Figure 4-16. Figure 4-16 DHCP Clients List ¾ Client Name - The name of the DHCP client ¾ MAC Address - The MAC address of[...]

TL-WR702N 150Mbps Wireless N Nano Router - 44 - ¾ Status - The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button. Then Figure 4-18 will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which yo u want to reserve a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 45 - Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup & Restor e, Reboot, Password, and S ystem Log. Click any of them, and you will be able to c onfigure the corresponding function. The detailed explanations f[...]

TL-WR702N 150Mbps Wireless N Nano Router - 46 - ¾ IP Address/Domain Name - T ype the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www .tp-link.com). ¾ Pings Coun t - The number of Ping packe ts for a Ping connection. The default is 4. ¾ Ping Packet Size - The size of Ping packet. The default is 64. ¾ Ping Ti meout - Se[...]

TL-WR702N 150Mbps Wireless N Nano Router - 47 - ¾ Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the R outer’s current hardware version. T o upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LIN[...]

TL-WR702N 150Mbps Wireless N Nano Router - 48 - ) Note: All changed settings will be lost when defaults are restored. 4.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore ”, and then you can save the current configuration of the Rout er as a backup file and restore the configuration via a backup file as shown in Figur[...]

TL-WR702N 150Mbps Wireless N Nano Router - 49 - • Change the LAN IP Address (syst em will reboot automatically). • Change the DHCP Settings. • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defa[...]

TL-WR702N 150Mbps Wireless N Nano Router - 50 - 4.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 4-27 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Rout er permanently, not just from the page.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 51 - Chapter 5. Configuration for Router Mode This chapter will show each W eb page's key functions and the confi guration way for Router Mode of TL-WR702N. 5.1 Login After your successful login, you can configur e and manage the device. T here are main menus on the left of the web-based utility . Sub[...]

TL-WR702N 150Mbps Wireless N Nano Router - 52 - Figure 5-2 ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 53 - ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page. • MAC Address - The physical address of the Rout er , as seen from the LAN. • IP Address - The LAN IP address of the Router . • Subnet Mask - The subnet mask associ[...]

TL-WR702N 150Mbps Wireless N Nano Router - 54 - • Received (Packets) - T raffic that counted in pa ckets has been received out from the W AN port. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset. Click the Refresh button to get the latest stat us and settings of the Router . 5.3 Quick Setup Please refer [...]

TL-WR702N 150Mbps Wireless N Nano Router - 55 - 5.5 Network Figure 5-5 the Network menu There are three submenus under the Network menu (shown in Figure 5-5): WA N , LAN a nd MAC Clone. Click any of them, and you will be able to configure the corresp onding function. 5.5.1 WAN Choose menu “ Network → WA N ”, and then you can configure t he IP[...]

TL-WR702N 150Mbps Wireless N Nano Router - 56 - This page displays the WAN IP parameters as signed dynamically by your ISP , including IP address, Subnet Mask, Default Gateway , etc. Click the Renew button to renew the IP p arameters from your ISP . Click the Release button to release the IP p arameters. ¾ MTU Size - The normal MTU (Maximum T rans[...]

TL-WR702N 150Mbps Wireless N Nano Router - 57 - ¾ IP Address - Enter the IP address in dotted-decimal not ation provided by yo ur ISP . ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP , usually is 255.255.255.0. ¾ Default Gateway - (Optional) Enter the gateway IP address in dotted-decimal not ation provided [...]

TL-WR702N 150Mbps Wireless N Nano Router - 58 - ¾ Secondary Connection - It’ s available only for PPPoE Connec tion. If your ISP provides an extra Connection type such as Dynamic/St at ic IP to connect to a local area network, then you can check the radio button of Dynamic/S tatic IP to activate this secondary connection. • Disabled - The Seco[...]

TL-WR702N 150Mbps Wireless N Nano Router - 59 - Figure 5-9 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP . ¾ Service Name/AC Name - The ser vice name and AC (Access Concentrator) name should not be configu[...]

TL-WR702N 150Mbps Wireless N Nano Router - 60 - Figure 5-10 W AN – L2TP/Russia L2TP ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ St atic IP - Choose either as you are gi ven by your ISP . Click the Connect button to connect immediately . Click the Disconnect button[...]

TL-WR702N 150Mbps Wireless N Nano Router - 61 - ¾ Connect Manually - Y ou can configure the Route r to make it connect or disconnect manually . After a specified period of inactivity ( Max Idle Time ), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you att[...]

TL-WR702N 150Mbps Wireless N Nano Router - 62 - ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S tatic IP - Choose either as you are gi ven by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domai n name, you should a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 63 - 5.5.2 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 5-12 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of your[...]

TL-WR702N 150Mbps Wireless N Nano Router - 64 - Some ISPs require that you re gister the MAC Address of your adapter . Changes are rarely needed here. ¾ WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-X[...]

TL-WR702N 150Mbps Wireless N Nano Router - 65 - Figure 5-15 Wireless Settings - Router ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXX XX indicates the last unique six numbers of each Route[...]

TL-WR702N 150Mbps Wireless N Nano Router - 66 - Select the desired wireless mode. When 802. 11g mode is selected, only 802.11g wireless stations can connect to the R outer. When 802.11n mode is se lected, only 802.11n wireless stations can connect to the AP. It is st rongly recommended that you set the Mode to 802.11b/g/n , and all of 802.11b, 802.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 67 - ¾ Authentication Type - This option should be c hosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authoriz ation type of the Root AP. ¾ Password - If the AP your Router is going to c onnect needs password, you need to fill the password in this blank. Be sure to click the Save butto[...]

TL-WR702N 150Mbps Wireless N Nano Router - 68 - Figure 5-16 Wireless Security ¾ Disable Security - The wireless security function can be enabled or disabled . If disabled, the wireless stations will be able to con nect the Ro uter without encryption. But it’s strongl y recommended to choose one of the following modes to enable security. ¾ WEP -[...]

TL-WR702N 150Mbps Wireless N Nano Router - 69 - • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these val ues are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "D[...]

TL-WR702N 150Mbps Wireless N Nano Router - 70 - For ASCII , the key can be made up of any numbe rs 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal , the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters. Please also note the key is case sens[...]

TL-WR702N 150Mbps Wireless N Nano Router - 71 - Figure 5-18 Add or Modify Wirele ss MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follo w these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit) . For example: 00[...]

TL-WR702N 150Mbps Wireless N Nano Router - 72 - 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B 0-00-0B/00-0 A-EB-00-07-5 F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status pull-down list. 4) Cl[...]

TL-WR702N 150Mbps Wireless N Nano Router - 73 - ¾ Beacon Interval - Enter a value between 20-1000 millise conds for Beacon Interval here. The beacons are the packets sent by the Router to synchr onize a wireless network. Beaco n Interval value determines the time interval of the beacons. The default value is 100. ¾ RTS Threshold - Here you can sp[...]

TL-WR702N 150Mbps Wireless N Nano Router - 74 - Figure 5-20 Wireless S tatistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless stat ion's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WP A-PSK / WPA 2 / WPA2-PSK / AP-UP / A P-DOWN / Disconnected ¾ Received Pack[...]

TL-WR702N 150Mbps Wireless N Nano Router - 75 - Figure 5-22 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to st art with when as[...]

TL-WR702N 150Mbps Wireless N Nano Router - 76 - 5.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in the screen as shown in Figure 5-23. Figure 5-23 DHCP Clients List ¾ Client Name - The name of the DHCP client ¾ MAC Address - The MAC address of[...]

TL-WR702N 150Mbps Wireless N Nano Router - 77 - ¾ Status - The status of this entry, either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button. Then will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which yo u want to reserve an IP a ddre[...]

TL-WR702N 150Mbps Wireless N Nano Router - 78 - 5.8.1 Virtual Servers Choose menu “ Forwarding → Virtual Servers ”, and then you can view and add virtual servers in the screen as shown in Figure 5-27. Virtual servers can be u sed for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service p[...]

TL-WR702N 150Mbps Wireless N Nano Router - 79 - Figure 5-28 Add or Modify a Virtual Server Entry ) Note: If your computer or server has more than one ty pe of available service, please select another service, and enter the same IP Addr ess for that computer or server . To modify or delete an existing entry: 1. Click the Modify in the entry you wa n[...]

TL-WR702N 150Mbps Wireless N Nano Router - 80 - Figure 5-29 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection us ing a destination port number defined in t he T rigger Port field. 2. The Router records this connection, opens t he incoming port or ports associated with this entry[...]

TL-WR702N 150Mbps Wireless N Nano Router - 81 - 5. Select Enable in Statu s field. 6. Click the Save button to save the new rule. Figure 5-30 Add or Modify a Port T riggering Entry T o modify or delete an existing entry: 1. Click the Modify in the entry you wa nt to modify . If you want to delete the entry , click the Delete . 2. Modify the informa[...]

TL-WR702N 150Mbps Wireless N Nano Router - 82 - Figure 5-31 DMZ T o assign a computer or server to be a DMZ server: 1. Check the Enable radio button. 2. Enter the IP Address of a local host in the DMZ Host IP Address field. 3. Click the Save button. ) Note: After you set the DMZ host, the firewa ll related to the host will not work. 5.8.4 UPnP Choo[...]

TL-WR702N 150Mbps Wireless N Nano Router - 83 - • Protocol - The type of protocol the Rout er opens for the application. • Internal Port - The Internal port the Router opens for local host. • IP Address - The IP address of the UPnP device t hat is currently accessing the Router. • Status - The status of the port is displayed her e. “Enabl[...]

TL-WR702N 150Mbps Wireless N Nano Router - 84 - ¾ Enable Firewall - the general firewall switch is on or of f. ¾ Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two default filtering rules of IP Address Filtering, either Allow or De ny passing through the router . ¾ Enable Domain Filtering - set Domain Fi[...]

TL-WR702N 150Mbps Wireless N Nano Router - 85 - 1. Effective Time - Enter a range of time in HHMM forma t, which point to the range time for the entry to take ef fect. For example, 0803 - 1705, t he entry will take effect from 08 :03 to 17:05. 2. LAN IP Address - Enter a LAN IP Address or a range of LAN IP addresses in the field, in dotted-decimal [...]

TL-WR702N 150Mbps Wireless N Nano Router - 86 - 5.9.3 Domain Filtering The Domain Filtering page allows you to control access to certain websites on the Internet by specifying their domai ns or key words. Figure 5-37 Domain Filtering Before adding a Domain Filtering entry , you m ust ensure that Enable Firewall and Enable Domain Filtering have been[...]

TL-WR702N 150Mbps Wireless N Nano Router - 87 - Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and the Previous button to return to the previ ous page. For example : if you want to block the PC(s) on your LAN to access websites www .xxyy .com[...]

TL-WR702N 150Mbps Wireless N Nano Router - 88 - Figure 5-40 Add or Modify a MAC Address Filtering entry T o add or modify a MAC Address Filter ing entry , follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit) . For example: 00-0E-AE[...]

TL-WR702N 150Mbps Wireless N Nano Router - 89 - 5.9.5 Remote Management Y ou can configure the Remote M anagement function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 5-41 Remote Management ¾ Web Management Port - W eb browser access normally uses the standard HTTP service port 80. T[...]

TL-WR702N 150Mbps Wireless N Nano Router - 90 - Figure 5-42 Advanced Security settings ¾ Packet s St a tistic interval (5 ~ 60) - The default value is 10. Se lect a value between 5 and 60 seconds in the pull-down list. The Packet s St atistic interval value indicates the time section of the packet s statistic. The resu lt of the statistic used for[...]

TL-WR702N 150Mbps Wireless N Nano Router - 91 - ¾ Ignore Ping Packet from W AN Port - Enable or Disable ignore ping packet from W AN port. The default is disabled. If enabl ed, the ping packet from the Internet cannot access the router . ¾ Forbid Ping Packet from LAN Port - Enable or Disable forbidding Ping Packet to access the router from the LA[...]

TL-WR702N 150Mbps Wireless N Nano Router - 92 - T o add st atic routing entries: 1. Click the Add New button. 2. Enter the following data: ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route. ¾ Subnet Mask - The Subnet Mask determines which portion of an IP Address [...]

TL-WR702N 150Mbps Wireless N Nano Router - 93 - Figure 5-46 IP QoS ¾ Enable IP Q oS - Enable or disable the function of IP QoS. ¾ Choose BandWid th T ype - Select the network connection ty pe from the drop-down list. ¾ Bandwidth Apply - The bandwidth you get. If you are not clear about that, please contact with your ISP for help. ¾ IP Range - I[...]

TL-WR702N 150Mbps Wireless N Nano Router - 94 - 4. IP address range for dif ferent entries coul d not have intersection with each other . 5. After the confi gurations, click the Save button for the change to t ake effect. 5.12 IP & MAC Binding Setting Figure 5-47 the IP & MAC Binding menu There are two submenus under the IP & MAC Bindin[...]

TL-WR702N 150Mbps Wireless N Nano Router - 95 - Figure 5-49 IP & MAC Bin ding Setting (Add & Modify) T o add IP & MAC Binding entries: 1. Click the Add New .. button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. T o modify or delete an existing entry : 1. Find the desired ent[...]

TL-WR702N 150Mbps Wireless N Nano Router - 96 - Click the Delete All button to delete all entries. 5.12.2 ARP List T o manage the computer , you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, a nd you could configure the items on the ARP list also. This p age displays the ARP Li st[...]

TL-WR702N 150Mbps Wireless N Nano Router - 97 - sign up for DDNS service providers s uch as www .dyndns.or g, www .oray .net or www .comexe.cn. The Dynamic DNS client service provi der will give you a password or key . 5.13.1 Ora y.net DDNS If your selected dynamic DNS Service Provider is www .oray .net, the page will appear as shown in Figure 5-52[...]

TL-WR702N 150Mbps Wireless N Nano Router - 98 - 5.14 System T ools Figure 5-53 The System T ools menu There are nine submenus under the System T ools menu: Tim e , Diagnostic , Firm w are , Factor y Default s, Backup and Restore, Reb oot, Password, Log and S tatistics. Click any of them, and you will be able to configure the corresponding function.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 99 - T o set time manually , follow the steps below: 1. Select your local time zone. 2. Enter the Date in Month/Day/Y ear format. 3. Enter the Ti me in Hour/Minute/Second format. 4. Click Save . For automatic time synchronization: 1. Enter the address of the NTP Server I or NTP Server II . 2. Click the Get[...]

TL-WR702N 150Mbps Wireless N Nano Router - 100 - Figure 5-55 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic too. • Ping - This diagnostic tool troubleshoots connectivity , reachabilit y , and name resolution to a given host or gateway . • T racerout e - This diagnostic tool test s the performance of a co[...]

TL-WR702N 150Mbps Wireless N Nano Router - 101 - ¾ T racerout e Max TTL - The max number of hop s for a T raceroute connection. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of t he Internet is fine. Figure 5[...]

TL-WR702N 150Mbps Wireless N Nano Router - 102 - 2. Make sure that your computer is connect ed to the Internet through the cable when you upgrade the firmware. To upgrade through wirel ess connection is not allowed. 3. Set your IP address as static IP before upgrading. T o upgrade the router's firmwa re, follow these instructions: 1. Download [...]

TL-WR702N 150Mbps Wireless N Nano Router - 103 - Figure 5-59 Backup & Restore Configuration ¾ Click the Backup button to save all configuration setti ngs as a backup file in your local computer . ¾ T o restore the router's configur ation, follow these instructions: • Click the Browse button to select the backup file which you want to r[...]

TL-WR702N 150Mbps Wireless N Nano Router - 104 - 5.14.7 Passw ord This page allows you to change the factory default user name and password of the router . Figure 5-61 Password It is recommended strongly that you change the factory default user name and password of the router . All users who try to access the router 's W e b-based utility or Q[...]

TL-WR702N 150Mbps Wireless N Nano Router - 105 - Click the Refresh button to refresh the logs. Click the Clear All button to clear all the logs. 5.14.9 Statistics The S tatistics page displays the net work traf fic of each PC in LAN, including total traffic and traf fic of the last Packet s St atistic interval seconds. Figure 5-63 S tatistics ¾ Cu[...]

TL-WR702N 150Mbps Wireless N Nano Router - 106 - UDP Tx The total amount of the UDP p ackets transmitted to W AN in the last Packet s Statistic interval seconds. TCP SYN Tx The total amount of the TCP SYN packets transmitted to W AN in the last Packet s St atistic interval seconds. Click the Save button to save the Packet s St atisti c interval val[...]

TL-WR702N 150Mbps Wireless N Nano Router - 107 - Chapter 6. Configuration for Repeater Mode This chapter will show each W eb page's key functions and the c onfiguration way for Repeater Mode of TL-WR702N. 6.1 Login After your successful login, you can configur e and manage the device. T here are main menus on the left of the web-based utility [...]

TL-WR702N 150Mbps Wireless N Nano Router - 108 - Figure 6-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware. ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page[...]

TL-WR702N 150Mbps Wireless N Nano Router - 109 - 6.4 Wo rking Mode The Router supports fi ve operation mode types: AP, Router , Repeater , Bridge and Client . Please select one your want. Click Save to save your choice, which is shown as Figure 4-3. Figure 6-3 W orking Mode ¾ AP - The wireless access point mode. ¾ Router - The wireless Router Mod[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 10 - 6.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 6-6 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of you[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 1 1 - Figure 6-8 Wireless Setting s - Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. I[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 12 - z Near the center of the area in which your wireless stations will operate. z In an elevated location such as a high shelf. z Away from the potential sources of interfer ence, such as PCs, microwaves, and cordless phones. z Away from large metal surfaces. 2. Failure to follow these gui delines can r[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 13 - Figure 6-10 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to st art with when [...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 14 - To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 6.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in th[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 15 - ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button. Then Figure 4[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 16 - 6.8 System T ools Figure 6-14 T he System T ools menu Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup & Restor e, Reboot, Password, and S ystem Log. Click any of them, and you will be able to c onfigure[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 17 - ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity , reachabilit y , and name resolution to a given host or gateway . • T racerout e - This diagnostic tool test s the performance of a connection. ) Note: Y ou can u[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 18 - Figure 6-17 Firmware Upgrade ¾ Firmware Version - This displays the current firmware version. ¾ Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the R outer’s current hardware version. T o upgrade the Router's firmware,[...]

TL-WR702N 150Mbps Wireless N Nano Router - 1 19 - Figure 6-18 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. • The default User Name : admin • The default Password : admin • The default IP Address : 192.168.0.254 • The default Subnet Mask : 255.255.255.0 ) Note: All changed sett[...]

TL-WR702N 150Mbps Wireless N Nano Router - 120 - 6.8.5 Reboot Choose menu “ System T ools → Reboot ”, and then you can click the Reboot button to reboot the Router via the next screen. Figure 6-20 Reboot the Router Some settings of the Router will take effect only after rebooting, including: • Change the LAN IP Address (syst em will reboot [...]

TL-WR702N 150Mbps Wireless N Nano Router - 121 - It is strongly recommended that you should change the factor y default user name and passwor d of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password. ) Note: The new user name and pas[...]

TL-WR702N 150Mbps Wireless N Nano Router - 122 - Chapter 7. Configuration for Bridge Mode This chapter will show each Web p age's key f unctions and the configurat ion way for Bridge Mode of TL-WR702N. 7.1 Login After your successful login, you can configur e and manage the device. T here are main menus on the left of the web-based utility . S[...]

TL-WR702N 150Mbps Wireless N Nano Router - 123 - Figure 7-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware. ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page[...]

TL-WR702N 150Mbps Wireless N Nano Router - 124 - • MAC address - The physical address of the Router , as seen from the WLAN. • WDS St atus - The status of WDS connection. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset. Click the Refresh button to get the latest stat us and settings of the Router . 7.3[...]

TL-WR702N 150Mbps Wireless N Nano Router - 125 - Figure 7-4 7.5 Network Figure 7-5 the Network menu There is only one submenu under the Network menu (shown in Figure 7-5): LAN . 7.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 7-6 LAN ¾ MAC Address - The physic[...]

TL-WR702N 150Mbps Wireless N Nano Router - 126 - 7.6 Wireless Figure 7-7 Wireless menu There are two submenus under the Wireless menu (shown in Figure 7-7): Wireless Settings and Wireless Security . Click any of them, and you will be able to configure the corresponding function. 7.6.1 Wireless Settings Choose menu “ Wir el es s → W ireless Sett[...]

TL-WR702N 150Mbps Wireless N Nano Router - 127 - name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test . ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. It may be illegal to use the wireless function o[...]

TL-WR702N 150Mbps Wireless N Nano Router - 128 - ¾ Authentication Type - This option should be c hosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authoriz ation type of the Root AP. ¾ Password - If the AP your Router is going to c onnect needs password, you need to fill the password in this blank. Be sure to click the Save butt[...]

TL-WR702N 150Mbps Wireless N Nano Router - 129 - Figure 7-9 Wireless Se curity ¾ Disable Security - The wireless security function can be enabled or disabled . If disabled, the wireless stations will be able to con nect the Ro uter without encryption. But it’s strongl y recommended to choose one of the following modes to enable security. ¾ WEP [...]

TL-WR702N 150Mbps Wireless N Nano Router - 130 - • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these val ues are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "[...]

TL-WR702N 150Mbps Wireless N Nano Router - 131 - For ASCII , the key can be made up of any numbe rs 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal , the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters. Please also note the key is case sen[...]

TL-WR702N 150Mbps Wireless N Nano Router - 132 - Figure 7-1 1 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to st art with when a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 133 - ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 7.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Route[...]

TL-WR702N 150Mbps Wireless N Nano Router - 134 - Figure 7-13 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the A[...]

TL-WR702N 150Mbps Wireless N Nano Router - 135 - Click the Next button to go to the next page and Click the Previous button to return the previous page. 7.8 System T ools Figure 7-15 T he System T ools menu Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup &[...]

TL-WR702N 150Mbps Wireless N Nano Router - 136 - Figure 7-16 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubles hoots connectivity , reachabilit y , and name resolution to a given host or gateway . • T racerout e - This diagnostic tool test s the performance of a [...]

TL-WR702N 150Mbps Wireless N Nano Router - 137 - ¾ T racerout e Max TTL - The max number of hops for a Tr aceroute connection. The default is 20. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of t he Internet[...]

TL-WR702N 150Mbps Wireless N Nano Router - 138 - 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware vers ions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware u n[...]

TL-WR702N 150Mbps Wireless N Nano Router - 139 - 7.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore ”, and then you can save the current configuration of the Rout er as a backup file and restore the configuration via a backup file as shown in Figure 7-20. Figure 7-20 Backup & Restore Configuration ¾ Click the B[...]

TL-WR702N 150Mbps Wireless N Nano Router - 140 - • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (syste m will reboot automatically). • Update the configuration wi th the file (system wi[...]

TL-WR702N 150Mbps Wireless N Nano Router - 141 - 7.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 7-23 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the R outer permanently, not just from the page.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 142 - Chapter 8. Configuration for Client Mode This chapter will show each Web p age's key func tions and the configuratio n way for Client Mode of TL-WR702N. 8.1 Login After your successful login, you can configur e and manage the device. T here are main menus on the left of the web-based utility . S[...]

TL-WR702N 150Mbps Wireless N Nano Router - 143 - Figure 8-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware. ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page[...]

TL-WR702N 150Mbps Wireless N Nano Router - 144 - 8.4 Wo rking Mode The Router supports fi ve operation mode types: AP, Router , Repeater , Bridge and Client . Please select one your want. Click Save to save your choice, which is shown as Figure 8-3. Figure 8-3 W orking Mode ¾ AP - The wireless access point mode. ¾ Router - The wireless Router Mod[...]

TL-WR702N 150Mbps Wireless N Nano Router - 145 - 8.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 8-6 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of your[...]

TL-WR702N 150Mbps Wireless N Nano Router - 146 - Figure 8-8 Wireless Setting s - Client ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXX XX indicates the last unique six numbers of each Rout[...]

TL-WR702N 150Mbps Wireless N Nano Router - 147 - Be sure to click the Save button to save your settings on this page. ) Note: 1. The operating distance or range of your wire less connection varies significantly based on the physical placement of the Router . Fo r best results, place your Router . z Near the center of the area in which your wireless[...]

TL-WR702N 150Mbps Wireless N Nano Router - 148 - Figure 8-10 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually . ¾ St art IP Address - S pecify an IP address for the DHCP Server to st art with when a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 149 - ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 8.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Route[...]

TL-WR702N 150Mbps Wireless N Nano Router - 150 - Figure 8-12 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the A[...]

TL-WR702N 150Mbps Wireless N Nano Router - 151 - Click the Next button to go to the next page and Click the Previous button to return the previous page. 8.8 System T ools Figure 8-14 T he System T ools menu Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup &[...]

TL-WR702N 150Mbps Wireless N Nano Router - 152 - Figure 8-15 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubles hoots connectivity , reachabilit y , and name resolution to a given host or gateway . • T racerout e - This diagnostic tool test s the performance of a [...]

TL-WR702N 150Mbps Wireless N Nano Router - 153 - ¾ T racerout e Max TTL - The max number of hops for a Tr aceroute connection. The default is 20. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of t he Internet[...]

TL-WR702N 150Mbps Wireless N Nano Router - 154 - 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware vers ions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware u n[...]

TL-WR702N 150Mbps Wireless N Nano Router - 155 - 8.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore ”, and then you can save the current configuration of the Rout er as a backup file and restore the configuration via a backup file as shown in Figure 8-19. Figure 8-19 Backup & Restore Configuration ¾ Click the B[...]

TL-WR702N 150Mbps Wireless N Nano Router - 156 - • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (syste m will reboot automatically). • Update the configuration wi th the file (system wi[...]

TL-WR702N 150Mbps Wireless N Nano Router - 157 - 8.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 8-22 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the R outer permanently, not just from the page.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 158 - Appendix A: FAQ 1. How do I configure the Router to access the Internet b y ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your AD SL Modem to the W AN port on the Router . The telephone cord plugs into the Line port of the ADSL M[...]

TL-WR702N 150Mbps Wireless N Nano Router - 159 - 2. How do I configure the Router to access the Internet b y Ethernet users? 1) Log in to th e Router , click the “ Netw ork ” menu on the left of your browser , and click " WA N " submenu. On the WA N page, select “Dynamic IP” for "W AN Connection T ype", finish by clickin[...]

TL-WR702N 150Mbps Wireless N Nano Router - 160 - Figure A-4 Virtual Serve rs Figure A-5 Add or Modify a Virtual server Entry ) Note: Your opposite side should call your WAN IP , which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the Router , click the “ Forwarding ” menu on the left of your browser , and click &qu[...]

TL-WR702N 150Mbps Wireless N Nano Router - 161 - 1) Because the WEB Server port 80 will inte rfere with the WEB management port 80 on the Router , you must change the WEB management port number to avoid interference. 2) T o change the WEB management port number : Log in to the Router , click the “ Security ” menu on the left of your browser , a[...]

TL-WR702N 150Mbps Wireless N Nano Router - 162 - Figure A-9 Add or Modify a Virtual server Entry 5. The wireless st ations cannot connect to the Router . 1) Make sure the " Enable Wireless Router Radio " is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations ha[...]

TL-WR702N 150Mbps Wireless N Nano Router - 163 - Appendix B: Configuring the PC In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows XP . First make sure your Ethernet Adapter is work ing, refer to the adapter ’s manual if necessary . 1. Configure TCP/IP comp onent 1) On the Windows taskbar , click the [...]

TL-WR702N 150Mbps Wireless N Nano Router - 164 - Figure 0-2 5) The following TCP/IP Properties window will display and the I P Address tab is open on this window by default. Now you have two ways to configure the TCP/IP protocol below: ¾ Setting IP address automatically Select Obtain an IP address automatically , Choose Obt ain DNS server automati[...]

TL-WR702N 150Mbps Wireless N Nano Router - 165 - Figure 0-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the Router's LAN IP addre ss is 192.168.0.254, specify the IP address as 192.16 8[...]

TL-WR702N 150Mbps Wireless N Nano Router - 166 - Now: Click OK to keep your settings.[...]

TL-WR702N 150Mbps Wireless N Nano Router - 167 - Appendix C: Specifications General S tandards IEEE 802.1 1n, 802.1 1b, 802.1 1g Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Port One 10/100Mbps LAN/W AN port, one USB port 10BASE-T : UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 Ω STP (maximum 100m) Cabling T ype 100BASE-TX: UTP[...]

TL-WR702N 150Mbps Wireless N Nano Router - 168 - Appendix D: Glossary ¾ 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses mu ltiple transmitter and receiver an tennas to allow for increased data throughput via spatial multiplexing and incr eas ed range by exploiting the spatial diver[...]

TL-WR702N 150Mbps Wireless N Nano Router - 169 - ¾ PPPoE ( P oint to P oint P rotocol o ver E thernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. ¾ SSID - A S ervice S et Id entification is a thirty-two char acter (maximum) alphan umeric key identifying a wire[...]