Deutsch dropdown-ico

Vermont Casting DVRS3 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Vermont Casting DVRS3 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Vermont Casting DVRS3, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Vermont Casting DVRS3 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Vermont Casting DVRS3. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Vermont Casting DVRS3 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Vermont Casting DVRS3
- Den Namen des Produzenten und das Produktionsjahr des Geräts Vermont Casting DVRS3
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Vermont Casting DVRS3
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Vermont Casting DVRS3 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Vermont Casting DVRS3 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Vermont Casting finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Vermont Casting DVRS3 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Vermont Casting DVRS3, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Vermont Casting DVRS3 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    - 1 - 10001293 11/01 Rev. 1 Rear V ented Direct V ent Models DVRS3 DVRSL DVRSR DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS: * Do not try to light any appliance. * Do not touch any electric switch * Do not use any phone in your buildin[...]

  • Seite 2

    - 2 - T ABLE OF CONTENTS Please read the Installation & Operating Instructions before using this appliance. Thank you and congratulations on your purchase of a Majestic fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and wi[...]

  • Seite 3

    - 3 - IMPORTANT: PLEASE REVIEW THE FOLLOWING CAREFULLY It is normal for fireplaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine. It is not unusual for your Majestic gas fireplace to give off some odour the firs[...]

  • Seite 4

    - 4 - FIREPLACE DIMENSIONS MANTELS Depending on the width of the mantel it may be installed higher or lower from the top of the louvre opening. See drawing and chart below for proper installation height of your combustible mantel piece. Non-combustible mantels may be installed at any height above the appliance opening. When using paint or lacquer t[...]

  • Seite 5

    - 5 - Do not use this fireplace if any part of it has been under water. Immediately call a qualified service technician to inspect the fireplace and replace any part of the control which has been under water. Fig. 4 Fig. 3 Rear ........ 0 mm/0 inches Floor ........ 0 mm/0 inches Top .......... 0 mm/0 inches Front & Side Glass 36" (914mm) t[...]

  • Seite 6

    - 6 - 1/2" GAS SUPPLY 1/2" X 3/8" REDUCER 3/8" NIPPLE 3/8" NIPPLE 3/8" NIPPLE 3/8" X 3/8" SHUT OFF VALVE 3/8" UNION When using copper or flex connector use only approved fittings. When using black iron pipe always provide a union so that gas line can be easily disconnected for burner or fan servicing. Se[...]

  • Seite 7

    - 7 - V V V V V V V V V X X X D E B B B C B M B A J K A F L G G TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA (TERMINATION PROHIBITED) H I Fixed Closed Fixed Closed Openable Openable Fixed Closed G G N N GENERAL VENTING Your fireplace is approved to be vented either through the side wall, or vertical through the roof. - Only Majestic v[...]

  • Seite 8

    - 8 - Outside Corner Inside Corner Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. A = Combustible 6"(152mm) Noncombustible 2"(50mm) B = Combustible 6"(152mm) Noncombustible 2"(50mm) A Balcony - with no side wall G = Combustible 24"(610mm) Non-Combustible 18"(4[...]

  • Seite 9

    - 9 - *IMPORTANT* Minimum clearance between vent pipes and combustible materials is one (1") inch (25 mm) on bottom, sides and top. Join pipes and secure joints with three (3) sheetmetal screws. (See Fig. 9) Wipe off excess sealant. GENERAL INFORMA TION ON ASSEMBLING THE VENT PIPES WITH CRIMPED ENDS BEAD LOCATION 1" FROM CRIMPED END OF PI[...]

  • Seite 10

    - 10 - The maximum horizontal vent run is 20 feet (6100mm) when the vertical vent rise is 7.5 feet (2286mm). Fig. 14 Since it is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust, certain limitations as to vent configurations apply and must be strictly adhered to. The graph showin[...]

  • Seite 11

    - 11 - Fig. 17 For each 45 degree elbow installed in the horizontal run (while maintaining a constant horizontal plane), the length of the horizontal run MUST be reduced by 18" (457mm). This does not apply if the 45 degree elbows are installed on the vertical part of the vent system. If a 90 degree elbow is used in the horizontal vent run (lev[...]

  • Seite 12

    - 12 - Fig. 19 COMBUSTIBLE WALLS (Fig. 19): Cut a 9-3/8"H x 9-3/8"W (240 mm x 240 mm) hole through the exterior wall and frame as shown NON-COMBUSTIBLE WALLS (Fig. 19): Hole opening must be 7.5" (190 mm) in diameter. (240mm) 9- 3/8 " 9- 3/8 " (240mm) 7- 1/2 " (190mm) Vent Opening — Combustible Wall Vent Opening — N[...]

  • Seite 13

    - 13 - Fig. 21 Fig. 20 STEP 4 (Fig. 22) Measure the horizontal length requirement including a 2" (50mm)overlap, i.e. from the elbow to the outside wall finish plus 2" (or the distance required if installing a second 90º elbow). STEP 3 (Fig. 21) Apply a bead of high temperature sealant to the inner and outer flue collars of the fireplace [...]

  • Seite 14

    - 14 - STEP 7 Support the horizontal pipes every 36 inches (914mm) with metal pipe straps. Make sure that the horizontal vent pipe is installed on a level horizontal plane. STEP 8 Recheck the fireplace to make sure that it is levelled, properly positioned, and nailed or screwed to the floor. If applied, the fireplaces adjustable frame drywall strip[...]

  • Seite 15

    - 15 - FOUNDATION RECESS SNORKEL SCREWS WALL SCREWS SHEET METAL WATERTIGHT SEAL AROUND PIPE If the foundation is recessed, use recess brackets (not supplied) for securing lower portion of the snorkel. Fasten brackets to wall first and then secure to snorkel with self drilling #8 x 1/2 sheet metal screws. It will be necessary to extend vent pipes ou[...]

  • Seite 16

    - 16 - Fig. 34 1. Locate your fireplace. 2. Plumb to centre of the (4") 90º transition elbow (7DVRT90) from ceiling above and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm). 4. Proceed to plumb for additional openings through the roof. In all cases, the opening must provide a minimum of 1 inch clearance to [...]

  • Seite 17

    - 17 - DVR SERIES CRIMPED VENTING COMPONENTS 7DVRVT - Through the wall Rear Vent Termination Starter Kit -Model 7DVSK - Sidewall Venting Starter Kit - Model 7DVSKV - Vertical Venting for 7DVSKV-A order 1/12 to 6/12 roof pitch for 7DVSKV-B order 7/12 to 12/12 roof pitch for 7DVSKV-F order flat roof Starter Kit - Model 7DVSKS -Snorkel Kit for Below G[...]

  • Seite 18

    - 18 - GENERAL INFORMA TION ON ASSEMBLING THE TWIST LOCK VENT PIPES When using CFM Majestic twist lock pipe it is not neces- sary to use silicone to seal the twist lock joints. The only areas that need silicone are the collars on the fireplace, the telescoping pipe (if used) and the horizontal termina- tion connection (when necessary). To join the [...]

  • Seite 19

    - 19 - Fig. 37 Combustible Walls. Cut a 10-3/8"H x 9-3/8"W (265mm x 240mm) hole through the exterior wall and frame as shown. Fig. 37. Non-Combustible Walls: Hole opening must be 7.5" (190mm) in diameter. To locate hole centre consult with appropriate fireplace specifications, page 4. (240mm) 9- 3/8 " 10- 3/8 " (254mm) 7- 1[...]

  • Seite 20

    - 20 - The maximum horizontal vent run is 20 feet (6100mm) when the vertical vent rise is 7.5 feet (2286mm). Fig. 41 Fig. 41 VERTICAL SIDEWALL INSTALLATIONS Since it is very important that the venting system maintain its balance between the combustion air intake and the flue gas exhaust, certain limitations as to vent configurations apply and must [...]

  • Seite 21

    - 21 - INSERT Fig. 44 The maximum number of elbow degrees in a system is 270 o . (This does not include transition elbow from rear vent to vertical vent.) Fig. 44 Sample: 1 - 90 o 2 - 45 o 3 - 45 o 4 - 90 o Total - 270 o 90" 2286mm 120" 3048mm 84" 2134mm 90 o elbow=3' Fig. 43 SEE PAGE 23 FOR VENTING REQUIREMENTS FOR SNORKELS. 3 [...]

  • Seite 22

    - 22 - VENT SIDEWALL INSTALLATION *IMPORTANT* Minimum clearance between vent pipes and combustible materials is one (1") inch (25 mm) on bottom, sides and top. Vent Starter Kit 7TDVSK, plus Transition Elbow 7TDVRT90 must be used in Vertical Sidewall installations. The 4" pipe must be centred inside the 7" pipe coming off the 7TDVRT90[...]

  • Seite 23

    - 23 - X Sealing vent pipe and firestop gaps with high temperature sealant will restrict cold air being drawn in around fireplace. Fig. 52 STEP 5 (Fig. 52) Use the appropriate length of pipe section – telescopic or fixed – and install. The 20" section of pipe which goes through the wall is packaged with the 7TDVSK kit, and can be cut to su[...]

  • Seite 24

    - 24 - DO NOT BACK FILL AROUND SNORKEL. SOIL SHOULD NOT BE LESS THAN 4" BELOW SNORKEL. FOUNDATION RECESS SNORKEL SCREWS WALL SCREWS SHEET METAL WATERTIGHT SEAL AROUND PIPE If the foundation is recessed, use recess brackets (not supplied) for securing lower portion of the snorkel. Fasten brackets to wall first and then secure to snorkel with se[...]

  • Seite 25

    - 25 - 1. Locate your fireplace. 2. Plumb to centre of the (4") 90 o transition elbow (7TDVRT90) from ceiling above and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm). 4. Proceed to plumb for additional openings through the roof. In all cases, the opening must provide a minimum of 1 inch clearance to the ven[...]

  • Seite 26

    - 26 - 7DVRVT - Through the wall Rear Vent Termination Starter Kit -Model 7TDVSK - Sidewall Venting Starter Kit - Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitch for 7TDVSKV-B order 7/12 to 12/12 roof pitch for 7TDVSKV-F order flat roof Starter Kit - Model 7TDVSKS -Snorkel Kit for Below Grade Installation 45 o elbow kit[...]

  • Seite 27

    - 27 - SIDE GLASS REMOVAL 1. Shut off gas. 2. Let the fireplace cool if it has been operating. 3. Remove side top louvre. (See Louvre Removal) 4. Open the side lower louvre assembly. 5. Release the two clamps at the bottom of the window frame by pulling down on the clamp handles. 6. Lift off the glass frame as shown. 7. To reinstall glass follow th[...]

  • Seite 28

    - 28 - REAR REFRACTORY BOTTOM SIDE REFRACTORY BOTTOM SIDE REFRACTORY BOTTOM END REFRACTORY BOTTOM REFRACTORY MANIFOLD SIDE CERAMIC REFRACTORY INSTALLATION 1 . Unpack ceramic refractory from its carton. HANDLE REFRACTORY CAREFULLY. 2. Place bottom refractory manifold side onto fireplace floor and slide under rear refractory. 3. Place bottom sides on[...]

  • Seite 29

    - 29 - INSTALLATION OF LOGS Left and right side are defined using the manifold as reference. Facing the manifold,the left side is on your left and the right side is on your right. Fig. 69 Fig. 70 Top logs must be placed properly onto notches LAVA ROCK The lava rock provided with this fireplace must be placed on the firebox base on either side of th[...]

  • Seite 30

    - 30 - 4. Push in gas control knob slightly and turn clockwise to "OFF". Do not force. 5. Close control access panel. C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Force or attempted repair may resu[...]

  • Seite 31

    - 31 - TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT 820 NOV A MILLIVOL T V AL VE START CHECK GLASS DOOR TO BE REMOVED BEFORE SERVICE WORK GAS SUPPLY ON • SHUTOFF VALVE OPEN • CONFIRM GAS HOOK-UP LIGHT PILOT WITH PIEZO IGNITION • ELECTRODE GAP MIN. 1/8" • ELECTRODE CRACKED • ELECTRODE CABLE ATTACHED • PIEZO IGNITOR GENERATES SPARK ?[...]

  • Seite 32

    - 32 - The burner and control system consists of: • main burners • gas orifices • pilot assembly • thermopile • millivolt gas valve Most of these components may require only an occasional checkup and cleaning and some may require adjustment. If repair is necessary, it should be performed by a qualified technician. 1. Turn off pilot light [...]

  • Seite 33

    - 33 - REPLACEMENT P AR TS - DVRS3 & DVRSL / DVRSR FOR FIREPLACES EQUIPPED WITH SIT 820 MILLIVOLT GAS VALVE[...]

  • Seite 34

    - 34 - REPLACEMENT P ARTS LIST - DVRS3/DVRSL/DVRSR D ESCRIPTION P AR T N O . DVRS3 DVRSL/DVRSR 1. Log Set Complete 10001271 100001271 1a. Log - Ember Log Set B18 B18 1b. Log - Ember Log Set B19 B19 1c. Log - Rear Pilot Side B20 B20 1d. Log - Rear Front Side B21 B21 1e. Log - Side Front B22 B22 1f. Log - Side Rear B23 B23 1g. Log - Center Right B24 [...]

  • Seite 35

    - 35 - EB1 1. Slide fan assembly from the left side into fireplace opening, line up mounting holes with screw studs on rear of fireplace and fasten with #10-24 hex nuts. 2. Install thermal sensor on bottom of firebox using #10-24 hex nuts. 3. (Option A) - Place electronic fan speed control box on bottom of fireplace base, lining up mounting holes w[...]