Vita-Mix T&G2 Bedienungsanleitung

All Models T&G 2 TM Blending Station ® High Performance Commercial Blender Owner ’ s Manual Read And Save These Instructions FOODSERVICE[...]

2 1. Read all instructions. 2. T o protect against risk of electrical shock, do not put motor base in water or other liquid. 3. Close adult supervision is necessary when appliance is used by or near children. 4. Unplug the power cord from the wall outlet when the T&G 2 Blending Station ® is not in use, before putting on or taking off parts, an[...]

3 13. Always operate with the lid in place. 14. Display window area will scratch when contacted with a scouring pad or sharp object. Use a soft cloth to wipe the control panel area clean. 15. The T&G 2 Blending Station ® cannot be cleaned with a water jet. 16. Installation for a 120 V AC unit requires you to have at least one 20 amp outlet per[...]

T&G 2 Blending Station ® On-Counter: Height of unit closed: 22” (54.56 cm) Shipping weight: 21 lbs. (9.534 kg) Dimensions: 22” High x 9-1/4” Wide x 10-1/2” Deep (54.56 cm x 23.45 cm x 25.86 cm) T&G 2 Blending Station In-Counter: Height of unit above counter: 17-1/2” (44.45 cm) closed Depth of unit below counter: 5-2/3” (13.3 cm[...]

5 T&G 2 Blending Station ® ON/OFF switch - Located on the side of the motor base the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending. SIX PROGRAM buttons - These buttons, numbered 1 thru 6, are pre-programmed blending cycles designed for the most commonly [...]

6 NOTE: Outside the United States and Canada, your T&G 2 Blending Station may come with a different container configuration. T wo-part Lid 32 oz. (900 ml) Xtreme Performance Container The two part lid is easy to clean and easy to put on, take off & seal. • T o remove a fully latched lid, lift the two tabs and pull upward and off. • T wi[...]

7 Cover with Removable Hinge Design Cover Door: 1. The Cover Door can be removed by opening it until the door is horizontal. Then, gently spread the sides of the door over the round hinges and remove. 2. T o reinstall the Cover Door , gently spread the sides of the door and place the door hinge cutouts over the round hinges. (Figure C) Back Cover: [...]

Preparing the counter area: • Before cutting holes, make sure that there is adequate clearance under the counter for the motor . The motor will extend about 5-2/3" (14.4 cm) below the counter but it is best to allow at least 10" (25.5 cm) from the under-counter to shelves or any other equipment under the counter . Also, when using the r[...]

In-Counter T&G 2 Blending Station ® dimensions: • 17-1/2” (44.45 cm) high with lid closed • 21-1/2” (54.7 cm) high with lid open • Case depth: 12-3/4” (32.39 cm) with handle • Case width: 9-1/2” (24.13 cm) • Depth below counter: 5-2/3” (14.4 cm) • Recommended distance between machines: 12” (30.48 cm) from the edge of ea[...]

Gasket Installation Instructions: 1. Follow the instructions on page 8 on preparing the counter area for the installation of your In-Counter T&G 2 Blending Station. ® Also, use the T emplate Sheet (provided in your machine’s original package) to assist you in the placement and ventilation of your machine. 2. Lay the blender on its back with [...]

11 The T&G 2 Blending Station ® advanced electronic control can be custom programmed by using the control panel. The two dif ferent programming instructions are explained below: Programming One of the Six T&G 2 Blending Station PRE-SET buttons 1. Press the OWNER CONTROL button (Vita-Mix Logo). 2. Press the PULSE High/Low buttons to scroll [...]

How to operate your T&G 2 Blending Station ® using the six Programmed Buttons. The following is the basic factory settings of the six PROGRAMMED buttons: • Press Button One for program - SMOOTHIE - Blends drinks with just juice and ice. • Press Button T wo for program - SMOOTH 2 - Blends regular smoothies for an extended cycle. • Press B[...]

7. When the cycle is complete the blender stops. W ait until blade comes to a complete stop before removing the lid and/or container from the motor base. 8. Remove the container , pour , garnish and serve the drink. NOTE: On all units the built-in thermal sensor keeps track of how hot the motor gets and will warn the user and eventually shut down t[...]

Item# Part #1 5573 32 oz. (90 0 m l) - XP Container without lid assembly or blade assembly #1 5571 32 oz. ( 900 m l) - XP Container , blade assembly , no lid assembly #1 159 32 oz. (900 ml) - Lid plug #15570 32 oz. (900 ml)- XP Container , blade assembly & lid assembly #15574 32 oz. (900 ml) - 2-piece lid assembly for XP Container #15575 32 oz.[...]

4 8 1 6 24 32 #15571 #15570 #15573 #18002 #18005 #15603 #18003 #1 159 #15575 #15598 #15585 #15579 #891 #15574 #15596 - Retainer Nut Wrench (Sold Separately) 15 #18004 #15576 One-Piece Lid (Sold Separately)[...]

Care Note T o ensure that you get the longest possible life from your Vita-Mix product, we recommend the following products, when used as directed by the supplier: Cleaning Product .......................................................................... Supplier Solid Supra, Solid Power , ..........................................................[...]

Motor Base 1. Unplug the power cord. 2. W ash outside surface with a damp soft cloth or sponge, which has been rinsed in a mild solution of liquid dish soap (Ivory Liquid ® or equivalent) in warm water . NEVER IMMERSE MOTOR BASE IN W A TER OR OTHER LIQUID. NEVER POUR W A TER OR ANY OTHER LIQUID ON THE MOTOR BASE. 3. Polish with a soft cloth. Contr[...]

T op nine problems you can fix on your own: T roubleshooting 18 1. Problem: • Display Panel reads Solution #1: T urn the machine off and on again to reset the programming. Solution #2: Call Vita-Mix Customer Service.* 2. Problem: • Loud noise from blender container blade area • Container blades do not spin • Increased vibration • Leaking [...]

Cooling the motor: If the machine has overheated: • The motor will stop and the message “MOT OR HAS OVERHEA TED REMOVE THE CONT AINER, THEN PRESS ST ART”, will scroll across the display window , while the words “HOT SHUTDOWN” will remain in the display window alerting you of the problem. • The machine will not run until the container is[...]

Retainer Nut Removal • The retainer nut is easily removed using the Retainer Nut Wrench. T o order a Retainer Nut Wrench please call your Vita-Mix distributor and ask for Item #15596. • T o remove, turn the container upside. Using the Retainer Nut Wrench turn the wrench counterclockwise to loosen the nut. Once loosened, remove by hand. • T o [...]

Limited Warranty Vita-Mix ® Corporation warrants your Commercial T&G 2 T M Blending Station ® to be free from defects in materials and workmanship for a period of three years from the date of purchase when used in accordance with the accompanying instruction booklet. Provisions of this limited warranty are void if your T&G 2 Blending Stat[...]

PLEASE NOTE: The Sevice Contract outlined in the following paragraph applies only to customers in the United States and Canada. Customers in all other countries should contact their local Vita-Mix distributor for service details. This T&G 2 TM Blending Station ® includes a 1-Y ear Service Contract effective from date of purchase. In the event [...]

©2005 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy , recording or any information storage and retrieval system without the written permission of the Vita-Mix Corporation. VIT A-MIX ® CORPORA TION Foodservice Division 8615 Usher Road, C[...]