Wagner SprayTech 558054 Bedienungsanleitung

Edition 5 / 2014 0558 977L ProSpray 3.39 GB Operating manual ProSpray 3.39 Airless high-pressure spraying unit Model: 0558054 0558079 Original operating manual[...]

GB Warning! Attention: Danger of injury by injection! Airless units develop extremely high spraying pressures. Be safety conscious! 1 2 3 Never put your ngers, hands or any other parts of the body into the spray jet! Never point the spray gun at yourself, other persons or animals. Never use the spray gun without safety guard. Do not treat a spra[...]

ProSpra y 3.39 3 GB Contents Contents Page 1. Safety regulations for Airless spraying ...................................... 4 1.1 Explanation of symbols used .............................................................. 4 1.2 Electric Safety ............................................................................................ 5 1.3 Electro[...]

4 ProSpra y 3.39 GB Safety Regulations 1. Safety regulations for Airless spraying 1.1 Explanation of symbols used This manual contains information that must be read and understood before using the equipment. When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard. This symbol i[...]

ProSpra y 3.39 5 GB Safety regulations  • Followmaterialandsolventmanufacturer’swarningsand instructions.Befamiliarwiththecoatingmaterial’sMSDS sheet and technical information to ensure safe use.  • Uselowestpossiblepressuretoushequipment.  • Whencle[...]

6 ProSpra y 3.39 GB General view of application Description of unit 2. General view of application 2.1 Application 2.2 Coating materials Processible coating materials i Pay attention to the Airless quality of the coating materials to be processed. Dilutable lacquers and paints or those containing solvents, two- component coating materials, dispersi[...]

ProSpra y 3.39 7 GB Description of unit 7 8 2 1 3 5 6 4 9 10 13 12 11 14 3.3 Legend for explanatory diagram ProSpray 3.39 1 Spray gun 2 High-pressure hose 3 Oil cup for EasyGlide (EasyGlide prevents increased wear of the packings) 4 Oil level gauge 5 Pail hook 6 Oil button 7 Suction tube 8 Return hose 9 Cart 10 Relief valve Lever position vertical [...]

8 ProSpra y 3.39 GB Description of unit 3.5 Technical data Voltage:  100-110VoltAC,50Hz Max. current consumption: 15 A / 20 A Power cord: 3 x 1.5 mm 2 – 6 m or 4.6 m Acceptance capacity: 2000 Watt Max. operating pressure: 221 bar (22,1 MPa) Volume ow at 12 MPa (120 bar) with water: 5.0 l/min Max tip size: 0.039 inch – 0.99 mm [...]

ProSpra y 3.39 9 GB Starting operation 4. Starting operation 4.1 High-pressure hose, spray gun and separating oil 1. Screw the high-pressure hose (2) to the coating material outlet (Fig. 4, Item 1). 2. Screw the spray gun (3) with the selected tip onto the high- pressure hose. 3. Tighten the union nuts at the high-pressure hoses rmly so that coa[...]

10 ProSpra y 3.39 GB Starting operation Solid Green When the pressure indicator is solid green, the sprayer is operating between 12 MPa (120 bar) and 23 MPa (230 bar). A solid green pressureindicatormeans:  • Thesprayerisattheproperpressuresettingforsprayingoil- based and latex house paints  • The[...]

ProSpra y 3.39 11 GB Starting operation 4.7 Digital Electronic Spray Control (DESC) The Digital Electronic Spray Control (DESC) increases the functionality of the sprayer. It is installed directly below the pressure control knob on the control panel. It consists of a display and four function keys. The display shows various menu screens that allow [...]

12 ProSpra y 3.39 GB Starting operation Spraying technique Security Code Screen SECURITY CODE CHANGE-2 MENU-1 The Security Code screen allows the user to set a four digit security code to prevent unauthorizeduseofthesprayer.Ifasecuritycodehasbeenset,the control system display will ask for the code at startu[...]

ProSpra y 3.39 13 GB Handling the high-pressure hose Cleaning the unit (shutting down) 6. Handling the high-pressure hose The unit is equipped with a high-pressure hose specially suited for piston pumps. Danger of injury through leaking high-pressure hose. Replace any damaged high-pressure hose immediately. Never repair defective high-pressure hose[...]

8.2 Cleaning the high-pressure lter Clean the lter cartridge regularly. A soiled or clogged high-pressure lter can cause a poor spray pattern or a clogged tip.  1. Turnthepressureregulatorknobintotheblackzoneuntilit stops (no pressure). 2. Open the relief valve, valve position PRIME ( k circulation). [...]

ProSpra y 3.39 15 GB Remedy in case of faults Digital Electronic Spray Control (DESC) Error Messages The following error message screens appear whenever the Digital Electronic Spray Control (DESC) detects a problem with the sprayer. Once a problem occurs and the error message appears, the sprayer will shut down. Before proceeding, relieve any press[...]

16 ProSpra y 3.39 GB Servicing Repairs at the unit 10. Servicing 10.1 General servicing Servicing of the unit should be carried out once annually by the WAGNER service. 1. Check high-pressure hoses, device connecting line and plug for damage. 2. Check the inlet valve, outlet valve and lter for wear. 10.2 High-pressure hose Inspect the high-press[...]

ProSpra y 3.39 17 GB Repairs at the unit 15. Clean all the parts with the corresponding cleaning agent. Check outlet valve housing (9), outlet valve seat (15), outlet valve ball (13) and upper ball guide (12) for wear and replace parts if necessary. If the worn outlet valve seat (15) is unused on one side, install it the other way around. 16. Carry[...]

18 ProSpra y 3.39 GB Repairs at the unit 19. Insert upper packing (Fig. 17) with O-ring (1) and protruding lip (2) downward. 1 2 20. Insert upper support ring (9) on top of the upper packing (10) 21. Thread the upper seal retainer (8) into the upper housing (2). 22. Rotate the upper housing in the vise so that the bottom end is facing up. 23. Inser[...]

ProSpra y 3.39 19 GB Appendix 12. Appendix 12.1 Selection of tip To achieve faultless and rational working, the selection of the tip is of the greatest importance. In many cases the correct tip can only be determined by means of a spraying test. Some rules for this: The spray jet must be even. If streaks appear in the spray jet the spraying pressur[...]

20 ProSpra y 3.39 GB Appendix 12.4 Airless tip table Wagner TradeTip 3 tip up to 270 bar (27 MPa) without tip Fthread(11/16-16UN) for W agner spra y guns Order no . 0289391 without tip Gthread(7/8-14UN) for Graco/T itan spray guns Order no . 0289390 i All of the tips in the table below are supplied together with [...]

ProSpra y 3.39 21 GB Appendix Application Tip marking Spray angle Bore inch / mm Spraying width mm 1) Gun lter Order no . Roof coatings 223 323 423 523 623 723 823 20° 30° 40° 50° 60° 70° 80° 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 0.023 / 0.58 120 150 190 225 270 300 330 white white white white white[...]

22 ProSpra y 3.39 GB Appendix 12.5 Pump-Runner (Order No. 2306987) Universalaccessoriesforcleaning,cleantransportationandpreservationofthepumpunit. Features:  • Simplercleaning–thecleaningliquidcirculatesconstantlythroughthepumpmakingthoroughcleaningoftheinte[...]

ProSpra y 3.39 23 www.wagner-group.com A J. W agner Ges.m.b.H. Ottogasse 2/20 2333 Leopoldsdorf Österreich T el. +43/ 2235 / 44 158 T elefax +43/ 2235 / 44 163 oce@wagner-group .at DK W agner Sprayt ech Scandinavia A/S Helgeshøj Allé 28 2630 T aastrup Denmark T el. +45/43/ 27 18 18 T elefax +45/43/ 43 05 28 wagner@wagner -group.dk GB W agner?[...]

24 ProSpra y 3.39 Accessories illustration ProSpray 3.39 3 1 5 8 2 4 7 9 10 6[...]

ProSpra y 3.39 25 Item Part No. Description 1 0296 388 Spray gun AG 08, F-thread 0296 386 Spray gun AG 08, G-thread 0502 166 Spray gun AG 14, F-thread 0502 119 Spray gun AG 14, G-thread 2 0296 441 Polegun120cm,G-thread7/8” 0296 443 Polegun120cm,F-thread11/16” 0296 442 Pole gun 200 cm,G-thread7/8” 0296 44[...]

26 ProSpra y 3.39 Spare parts list ProSpray 3.39 59 60 61 1 3 4 38 5 6 9 8 35 2 36 7 2 10 11 12 13 17 16 14 15 18 19 20 21 22 23 24 26 27 28 30 31 32 33 29 25 37 39 41 34 40 43 42 46 44 45 47 48 49 Main Assembly 52 53 54 57 58 51 50 55 56 62 63 64 0558 599 120V 6 m 0290 299 120V 4.6 m BS4343 NEMA 5-15P[...]

ProSpra y 3.39 27 Item Part No. Description 1 0290 271 Motor shroud 2 0508 559 Screw (2) 3 0558 500 Belly pan assembly 4 9802 266 Screw (2) 5 0290 228 Door 6 0509 218 Screw (2) 7 0290 253 Grommit 8 0551 778 Transducer assembly 9 0558 710 Filter assembly 10 0507 785 Return tube 11 0290 248 Hose 12 0507 786 Washer (2) 13 9805 311 Screw (2) 14 9802 26[...]

28 ProSpra y 3.39 Spare parts list ProSpray 3.39 1 10 9 8 7 6 2 3 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 4 5 11 32 30 31 Fluid section Item Part No. Description 1 0558 419 Cylinder 2 0524 905 Stopping spacer 3 0524 906 Extension bushing 4 0558 570A Piston extension 5 0558 422 Extension slider 6 9832 126 Connecting pin (2) 7 0290 266 [...]

ProSpra y 3.39 29 Spare parts list ProSpray 3.39 7 16 17 4 5 6 8 9 13 12 14 15 10 11 1 2 3 18 19 20 Drive Assembly Item Part No. Description 1 0558 572A Slider assembly 2 0507 767 Screw (4) 3 0290 272 Slider housing 4 0558 342A Housing assembly 5 0558 362 3rd stage gear 6 0558 363 2nd stage gear 7 9821 503 Washer (3) 8 700-287 Screw (3) 9 0509 218 [...]

30 ProSpra y 3.39 Filter assembly Spare parts list ProSpray 3.39 1 15 2 3 4 5 6 7 8 9 10 11 12 13 14 Item Part No. Description 1 0524 918 Filter housing 2 14058 Conical spring 3 0508 748 Filter, 60 mesh (standard) 0508 451 Filter, 30 mesh 0508 452 Filter, 100 mesh 4 0508 603 Bearing ring 5 0508 749 Bearing spring 6 0551 951 O-ring 7 0509 420 Pipe p[...]

ProSpra y 3.39 31 Spare parts list ProSpray 3.39 15 1 2 3 4 5 7 6 8 9 17 16 18 13 14 15 12 11 10 19 20 Upright cart assembly Item Part No. Description 1 805-206A Handle assembly (includes items 8-9) 2 9805 352 Screw (2) 3 0290 257 Bushing 4 805-200 Cart weldment 5 9894 275 Spring 6 0290 294 Sleeve 7 0290 285 Carriage assembly 8 0509 386 Washer (4) [...]

32 ProSpra y 3.39 GB Important notes on product liability As a result of an EC regulation being eective as from January 1, 1990, the manufacturer shall only be liable for his product if all parts come from him or are released by him, and if the devices are properly mounted and operated. If the user applies outside accessories and spare parts, th[...]