Woods Equipment BW15LH Bedienungsanleitung
- Schauen Sie die Anleitung online durch oderladen Sie diese herunter
- 72 Seiten
- 3.85 mb
Zur Seite of
Ähnliche Gebrauchsanleitungen
-
Brush Cutter
Woods Equipment BB60X
60 Seiten 3.1 mb -
Brush Cutter
Woods Equipment DS1440Q
86 Seiten 4.75 mb -
Brush Cutter
Woods Equipment DS1260Q
86 Seiten 4.75 mb -
Brush Cutter
Woods Equipment MD80-2
62 Seiten 5.96 mb -
Brush Cutter
Woods Equipment DSO1260
86 Seiten 4.75 mb -
Brush Cutter
Woods Equipment BB8400X
50 Seiten 7.32 mb -
Brush Cutter
Woods Equipment S105-3
58 Seiten 4.72 mb -
Brush Cutter
Woods Equipment DS1260
86 Seiten 4.75 mb
Richtige Gebrauchsanleitung
Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Woods Equipment BW15LH an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Woods Equipment BW15LH, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.
Was ist eine Gebrauchsanleitung?
Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Woods Equipment BW15LH die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.
Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Woods Equipment BW15LH. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.
Was sollte also eine ideale Gebrauchsanleitung beinhalten?
Die Gebrauchsanleitung Woods Equipment BW15LH sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Woods Equipment BW15LH
- Den Namen des Produzenten und das Produktionsjahr des Geräts Woods Equipment BW15LH
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Woods Equipment BW15LH
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen
Warum lesen wir keine Gebrauchsanleitungen?
Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Woods Equipment BW15LH zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Woods Equipment BW15LH und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Woods Equipment finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Woods Equipment BW15LH zu überspringen, wie es bei der Papierform passiert.
Warum sollte man Gebrauchsanleitungen lesen?
In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Woods Equipment BW15LH, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.
Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Woods Equipment BW15LH widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.
Inhaltsverzeichnis der Gebrauchsanleitungen
-
Seite 1
OP E R A TO R ' S M A NU A L BA TWING - ROT ARY CUTTER MAN0810 (Rev . 07/ 09/ 201 0) ® BW15LH[...]
-
Seite 2
2 Introduction Gen’l (Rev . 3/5/2010 ) T O THE DEALER: Assemb ly and prop er installati on of this product is the respons ibil ity of the Woods ® dea ler . Read manua l instr uctions and safet y rules . Mak e su re all items on the Dealer ’s Pre-Del ivery and Deliver y Check Lists in the Ope rator ’s Manual are com pleted before r eleasin g [...]
-
Seite 3
Introduction 3 MAN 081 0 (9/ 24/ 200 9) T ABLE OF CONTENT S INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICA TIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORM A TIO N . . . . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Seite 4
4 Introduction MAN08 10 (9/24/2009) SPECIFICATIONS BW15LH Cutting H eight ( V aries with tire s electio n) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1" - 12" Cutting W idth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]
-
Seite 5
Safe ty 5 Safety V ideo O rder Form ( 8/2/2005) Free Mower Safety V ideo Fill out and return the o rder form and we will send you a FREE VHS or DVD video outlinin g Industrial and Agricu ltural Mower Safe ty Practices . The 22 minute video, developed in co operation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures[...]
-
Seite 6
6 Sa fety Safety V ideo Ord er Form (Rev . 2/6/2006 ) Free Mower / Cutter Safety Video Order Form 3 (Select one) VHS Forma t - VHS01052 Safety V ideo DVD Format - DVD010 52 Safety V ideo Please send me Name: _______ _______ _________ _______ _______ ___ Phone: _______ _______ ____ Address: __ _______ _______ _________ _______ _____ ______ _[...]
-
Seite 7
Safety 7 BW180LH _SR (10/15/200 9) INST ALLA TION Hydraulics must be connected as instructed in this manual. Do not substitute part s, modify , or connect in any other way . TRAINING Saf ety in struc tions are imp ort ant ! Read all att achment and power unit manua ls; follow all safety ru les and safety d ecal i nformat ion. (Rep lace- men[...]
-
Seite 8
8 Safety BW180LH _SR (10/15/2009 ) (Safety R ules conti nued from previous page) Before st arting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards ro tate f reely on all driveli nes. If guards do not rotate freely on drive- lines, repair and replace bearings before putting equipment i[...]
-
Seite 9
Safety 9 BW180LH _SR (10/15/200 9) Always comp ly with all state and local light ing and marking requirement s. Never allow riders on power unit or att achment. Power unit must be equippe d with ROPS or ROPS cab and seat belt. Keep seat belt securely fasten ed. Fall ing of f power unit can resu lt in dea th from being r un over or crush[...]
-
Seite 10
10 Safety BW180LH _SR (10/15/2009 ) (Safety R ules conti nued from previous page) Keep all persons away from operator cont rol area while p erforming adju stments, service, or maintenance. Make cert a in all movem ent of equipm ent c om- ponents has stop ped befo re appr oachin g for ser - vice. Frequently check blades. They should be s[...]
-
Seite 11
Safe ty 11 MAN08 10 (9/24/2009) 4 - PN 18869 SHIELD MISSING DO NOT OPERA TE - PUT SHIELD ON 18869-B DANGER BE CAREFUL! Use a cl ean, da mp c loth to clea n saf ety de cals . A void spr aying too clo se to d ecals when using a pr essure washer; high-pressure water ca n ent er through ve ry small scra tches or under edges of decals causing them to pe[...]
-
Seite 12
12 Safety MAN0810 (9/24/2009 ) 6 - PN 15503 F ALLING OFF CAN RESUL T IN BEING RUN OVER. T ractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times. Buckle Up! Keep seat belt securely fastened. Allow no riders. RAISED EQUIPMENT CAN DROP AND CRUSH. Before workin[...]
-
Seite 13
Safety 13 MAN08 10 (9/24/2009) SAFETY & INSTRUCTIONAL DECALS A TTENTION! BECOME ALERT! YOUR SAFETY IS INVOL VED! Replace Immediatel y If Damaged! 1 1 - PN 10049 91 TRANSPORT LOCK AND CYLINDER REQUIREMENTS 1004991 TRANSPORT LOCK W ARNING RAISED CUTTER CAN DROP AND CRUSH e rs must be e q ui pp ed with trans p ort lock . Cutt e ds. sta n r ans[...]
-
Seite 14
14 Operation MAN0810 (9/24/2009 ) OPERATION The des igned and tested s afety of this ma chin e depends on i t bei ng ope rated wi thin the lim itations as explain ed in this manual . Be famili ar wit h and follow all safety rul es in the manual , on the cutter a nd on th e tractor . The safe operatio n of this cutter i s the res ponsi bility o f th[...]
-
Seite 15
Operation 15 MAN08 10 (9/24/2009) Interf ere nce Chec k 1. Be sur e that trac tor 3-p oint l ift links do not in terf ere with hydr auli c hos es, cu tter dri veline, o r cut ter frame. 2. Check for st raigh t-ahe ad operati on and at full turning a ngles. If there is any inte rference, r emove the lo wer lift l inks. 3. Contact betw een tr actor l[...]
-
Seite 16
16 Operation MAN0810 (9/24/2009 ) CUTTER OPERATION When begi nning op eration of the cutter , make sur e that all per sons are in a safe l ocation. Power for ope rating the cut ter is suppl ied by the trac tor PT O. Ope rate PTO at 540. Know how to stop the tract or and cutter quickl y in an emergenc y . Engag e P TO at a low engi ne, rpm to minim [...]
-
Seite 17
Operation 17 MAN08 10 (9/24/2009) TRANSPORTING Power unit must be equippe d with ROPS or ROPS cab and seat belt. Keep seat belt securely fasten ed. Fall ing of f power unit can resu lt in dea th from being r un over or crushed. Keep foldable ROPS sy stem in “lock ed up” position at all times. Always rai se unit an d install transport lo[...]
-
Seite 18
18 Operation MAN0810 (9/24/2009 ) STO R A GE Follow these ste ps when storing your cutte r: 1. Clean cutte r before s toring. Se e page 23 for cleanin g ins truct ions. S tore on lev el, sol id groun d. 2. Disconn ect drivel ine an d secur e up off the g round. 3. Lower win gs to g round. 4. Raise cutte r ce nter sect ion and pin t ransport b ar in[...]
-
Seite 19
Owner Service 19 MAN081 0 (9/24/20 09) OWNER SER VICE The info rmation in t his s ection i s written for oper ators who po ssess ba sic mecha nical ski lls. I f you ne ed help, your dea ler h as train ed ser vice te chni cians av aila ble. For your protec tion, read and follow the safety informa- tion in th is ma nual. Keep all persons away fro[...]
-
Seite 20
20 Owner Service MAN08 10 (9/24/2009) Figure 5 . Jackstand P lacemen t and Lu bricati on Poi nts LUBRICA TION Do not le t exces s grease coll ect on or around parts, particularl y when operatin g in s andy a reas. See Figu re 5 for lub ricatio n points and frequency or lubric ation based on nor mal operati ng condi tions. Sev ere or un usual condi [...]
-
Seite 21
Owner Service 21 MAN081 0 (9/24/20 09) Seasonal Lubrication In additi on to the daily r ecomm ended l ubrica tion, a more ex tensive applic ation i s recomm ended seaso n- ally . 1. Fill CV doub le yokes with 20 p umps of grease wit h the jo ints in a str aight line. 2. Articu late CV b ody to ma ximu m angle several times to ensure fu ll cov erage[...]
-
Seite 22
22 Owner Service MAN08 10 (9/24/2009) Blade Sharpening NOTICE ■ When sharpening blades, grind the same amount on each blade to maint ain balance. Replace bl ades in p airs . Unbala nced bla des wi ll cause ex cessive vib ration , which c an damag e gearbox bearings. Vibration may als o cause struc- tural crac ks to c utter . 1. Sharpen both bla d[...]
-
Seite 23
Owner Service 23 MAN081 0 (9/24/20 09) SHIE LDI NG REPAIR Full chain or rubber shielding must be inst alled when operating in populated areas or other areas where thrown o bject s co uld injure p eople or dam- age property . • If this machine is not equipped with full chain or rubber shi elding , operation must be sto pped when anyon e comes [...]
-
Seite 24
24 T roubleshooting MAN08 10 (9/24/2009) TROUB LESHOOTI NG PROBLEM POSSIBLE CAUSE SOLUTION Does not cut Dull blade s Sharp en blades. Worn or bro ken blade s Replac e blade s. (R eplace i n pairs onl y .) Incorr ect PTO speed Set at r ated PTO speed. Groun d speed to o fast Reduce g round s peed. Drive not functioni ng (b lades do not turn when PTO[...]
-
Seite 25
Dealer Service 25 MAN081 0 (9/24/20 09) DEALER SER VICE The info rmation in thi s se ction is written for de aler ser - vice per sonnel. T he repair desc ribe d here requ ires special skil ls and tools. If yo ur sh op is not pr operly equipp ed or you r mechan ics a re not properl y traine d in this type of repair , y ou may be time and mon ey ahea[...]
-
Seite 26
26 Dealer Service MAN08 10 (9/24/2009) V ERTICAL SH AF T SEAL REPAIR (S PINDLE BOX) Refer to Figure 1 1. 1. Disconn ect and r emove t he dr iveline from the gearbox . 2. Remove v ent plu g (3) an d siphon gear lub e from housing throug h this op ening. 3. Remove crossbar (Se e “CROSSBAR REMOV A L” on page 31.). 4. Remove v ertical s haft seal ([...]
-
Seite 27
Dealer Service 27 MAN081 0 (9/24/20 09) Figure 1 1 . S pindle Gea rbox Ass embly 1. Gearbox hous ing 2. Cap sc rew 14 mm x 1 .25 3. V ent plug 4. T op co ver 5. Shim kit 6. Crown ge ar 7. Beari ng cu p & co ne 8. Cotter p in B6 x 60 mm 9. Sn ap ri ng 10. Se al 1 1. Input shaft 12. Castle nut, me tric M3 0 x 1.5 13. Pini on gear 14. Sh im kit 15[...]
-
Seite 28
28 Dealer Service MAN08 10 (9/24/2009) ASSEMBLE GEARBOX Refer to Figure 1 1. 1. Clean hou sing, paying spec ific at tention to ar eas wher e gaske ts wi ll be in stall ed. 2. W ash housing a nd all comp onents thoro ughly . Select a c lean area for gearbox assembl y . Re place all sea ls, bear ings, a nd gas kets. All parts m ust be clean an d ligh[...]
-
Seite 29
Dealer Service 29 MAN081 0 (9/24/20 09) SPLITTER GEARBOX REP AIR (Figure 12) Removal from Cutter 1. Disconn ect and re move a ll drivel ines from gearbox . 2. Remove th e four c ap screw and loc k washers that secu re gear box to cu tter , and re move gearbox. NOTE: Gearbo x is hea vy: d o not att empt to m ove it without mechani cal assis tance. D[...]
-
Seite 30
30 Dealer Service MAN08 10 (9/24/2009) Check Gea rbox 1. Place top co ver (21) on housi ng and secur e into position usin g six cap screws (20). 2. Check ge arbox f or le aks by : plugg ing all holes except o ne, appl ying 4 psi of co mpress ed ai r , and immers ing gearbo x in water . V erify gea rbox does not lea k. NOTE: Excessiv e air pres sure[...]
-
Seite 31
Dealer Service 31 MAN081 0 (9/24/20 09) CROSSBAR REM OV AL 1. It is neces sary to gain ac cess to bottom side of cutter for cross bar remova l. See Bl ocki ng Metho d pag e 19 . NOTE: Y ou wil l need to us e eith er the pul ler sc rew (Ite m 6, Fig ure 14) or a sm all hydr auli c jack to remove the cr ossbar . 2. Remove bl ades from cr ossbar as sh[...]
-
Seite 32
32 Dealer Service MAN08 10 (9/24/2009) CROSSBAR INST ALLATION 1. Usi ng eme ry clo th (2 20 or f iner) , re move s urface rust, Loct ite ® and foreign mate rial fro m hub, splined gea rbox ve rtic al shaft, a nd cros sbar assembl y . 2. Slide c rossb ar ass embly (10) onto s pline d shaft. Install nut ( 86) and al ign a slo t with hol e in spli ne[...]
-
Seite 33
Dealer Service 33 MAN081 0 (9/24/20 09) 4. Place u niver sal cr oss in vis e as s hown i n Figur e 20 and tap on yo ke to re move cup. Rep eat S tep 3 for final r emov al. Dr ive r emain ing cup out with a dri ft and hamme r . Figure 20 U-Joint Assembly 1. Place s eals sec urel y on bea ring cu ps. Inse rt cup into yo ke from outsi de and pr ess in[...]
-
Seite 34
34 Assembly MAN08 10 (9/24/2009) ASSEMBLY INSTRUCTIONS DEALER SET - UP INSTRUCTIONS Assemb ly of this c utter is th e resp onsibil ity of th e WOODS dealer . It should be deli vere d to the owner complete ly a ssemble d, lub ricated and adjus ted fo r nor- mal cutti ng co nditions . The cutter is shippe d partially ass embl ed. Assemb ly will be ea[...]
-
Seite 35
Assem bly 35 MAN081 0 (9/24/20 09) Inst all Height Adjustment Cylinder Refer to Figur e 23. 1. Attach bas e end of cylinde r (21 ) to the sp ring a rm (19) usin g clevi s pin ( 32) and tw o cotte r pins (80 ). 2. Extend cyli nder r od a nd pl ace t ranspor t lock bracke t (22) o ver cylinde r rod c levis. 3. Positio n cyl inder r od and transpo rt [...]
-
Seite 36
36 Assembly MAN08 10 (9/24/2009) Inst all Wheel a nd Hub 1. Insert whe el hub in to outside of wheel yo ke arm (17) an d align ho les. 2. Secu re into p ositi on usin g cap screw (64) an d flanged l ock nut ( 68). 3. Att ach wh eel to hub us ing five lug nu ts. In stal l the chamf ered side o f the l ug nut toward the in side for steel r im for pne[...]
-
Seite 37
Assem bly 37 MAN081 0 (9/24/20 09) Inst all CV Drive 1. Align h ole i n dri ve yok e with groo ve on gearbox input sh aft and slide rear half of dr ive (5) onto shaft. 2. Secure with bo lt and nut sup plied wit h drive . Figure 26 . CV Dri ve Installa tion Inst all Wing Use a suitable lif ting devic e of sufficient cap ac- ity . Use adequate pe[...]
-
Seite 38
38 Assembly MAN08 10 (9/24/2009) 2. Slide spac er (38) and lock- up bar ( 13) over cl evis pin (33 ) on bac k side of cy linder lug & s ecure with 1"x1-7 /8" washe rs (53) a nd cot ter pins ( 80). 3. Attach base en d of wing cyl inder (4) to cylind er links ( 1 1 & 12) an d washers (52) usi ng clevis pin (32) and c otter pin s (80[...]
-
Seite 39
Assem bly 39 MAN081 0 (9/24/20 09) Inst all W ing Wheel Y oke Adjustment Link Use a suitable lif ting devic e of sufficient cap ac- ity . Use adequate personnel to handle heavy com- ponent s. 1. With a lifting de vice raise right wing and lo ck in th e up positi on usin g the wing loc k-up bar . Leav e lifting device attache d for adde d supp o[...]
-
Seite 40
40 Assembly MAN08 10 (9/24/2009) Inst all Chain or Belt Shielding Full chain shielding must be installed when operating in popul ated areas or other areas where thrown obj ects could inju re peop le or dama ge property . • If this machine is not equipped with full chain shielding, operation must be stop ped when any- one comes w ithin 300 fee[...]
-
Seite 41
Assem bly 41 MAN081 0 (9/24/20 09) Figure 34 . Chain S hield ing Installa tion - Right Wi ng Show n 6. Front ri ght wing c hain pla te, inner - o r- 6. Front left wing chai n pla te, inner 7. Front ri ght wing c hain pla te, middle - or- 7. Front left wing chai n pla te, mid dle 8. Front ri ght wing c hain pla te, outer -or- 8. Fron t left wing c h[...]
-
Seite 42
42 Assembly MAN08 10 (9/24/2009) Figure 35 . Belt S hield ing Ins tallation - Center Sectio n Figure 36 . Belt S hield ing Installat ion - Right W ing 1. Front Ce nter B elt Shie ld Pl ate 2. Front Ri ght Be lt Shiel d Plate 3. Front Le ft Belt Sh ield Pla te 7. Bent Link .18 x 13.00 8. Bent Link .18 x 9.50 9. Rubb er Shie ld Fron t 13. Rubber Sh i[...]
-
Seite 43
Dealer Check List s 43 MAN0810 (9/24/2009) DEALER CH ECK LIST S PRE- DELIV ERY CH ECK LIS T (DEALER’S RESPONSI BILITY) Inspect t he equipme nt thor oughly aft er asse mbly to ensure it is set up pro perly before deli vering it to the cust omer . The foll owing che ck lis ts are a r eminder of poin ts to insp ect. Che ck off each i tem as it is fo[...]
-
Seite 44
44 Notes MAN08 10 (9/24/2009) NOTES[...]
-
Seite 45
Part s 45 MAN081 0 (9/24/20 09) P ARTS INDEX BA TWING ® Rot ary Cu tter BW15LH MAIN FR AME A SSEMBL Y (FRONT SECTI ON) ....... .................... ............ ............. .. 46 -47 (REAR SECTIO N) .... ............. ............. ............ ............. .. 48 -49 WING ASSE MBLY .................. ............. ............. ................[...]
-
Seite 46
46 Part s MAN08 10 (9/24/2009) MAIN FRAME ASSEMBLY (FRONT SECTION) 90 - COMPLE TE DECAL SET 91 - SAFETY DECAL SET (Rev . 3/3/20 10)[...]
-
Seite 47
Part s 47 MAN081 0 (9/24/20 09) MAIN FRAME ASSEMB LY (FRONT SECTION) R E F P ART QTY DESCRIPTION 1 1916 0KT 1 Blade k it, CCW 2 10322 98 1 Gearbo x (see p age 54) 3 10321 85 1 Drive line comple te, 1340, 1.75-20.8 w/ clutch (see p age 56) 4 10036 87 1 S plitte r gearbox (see pa ge 52) 5 10321 89 1 CV drive (s ee p age 57 ) 6 10034 91 1 Attitu de ro[...]
-
Seite 48
48 Part s MAN08 10 (9/24/2009) MAIN FRAME ASSEMBL Y (REAR SECTION)[...]
-
Seite 49
Part s 49 MAN081 0 (9/24/20 09) MAIN FRAME ASSEMBL Y (REAR SECTION) REF P ART QTY DESCRIPTION 6 1003491 1 Attitu de rod 1 1 1003495 2 Hinge pin 17 1032200 1 Center wheel y oke 18 5705 0 1 Access h ole cove r 19 1032225 1 S pring arm 20 13316 1 S pring 21 29547 1 Hydrauli c cylin der 3 x 8 (see pa ge 64) 22 1004814 1 Tr ansport lo ck-up 23 24098 1 1[...]
-
Seite 50
50 Part s MAN08 10 (9/24/2009) WING ASSEMBLY (Rev . 3/3/20 10)[...]
-
Seite 51
Part s 51 MAN081 0 (9/24/20 09) WING ASSEMBL Y REF P ART QTY DESCRIPTION REF P ART QTY DESCRIP TION 1 19160KT 1 Blade kit, C CW (Right wing) - or - 1 19161KT 1 Blade kit, CW (Le ft wing) 2 1032297 1 Gearbox (Ri ght wing, s ee page 5 4) - or - 2 10 322 98 1 Gearb ox ( Leftt wing , se e page 54) 3 1032186 1 Driveline c omplete 124 0, 49.6 x 71.3(se e[...]
-
Seite 52
52 Part s MAN08 10 (9/24/2009) SPLI TTER GEARBOX ASSEMBLY[...]
-
Seite 53
Part s 53 MAN081 0 (9/24/20 09) SPLITTER GEARBOX ASSEMBLY REF PART QTY DESCRIPTION A 1003687 1 Complete splitte r gearbox 1 100 5308 2 Shaft 1-3/4, 20 splin e, wing 2 100 5304 2 Oil sea l 3 -------- 2 3/8 Plug (not shown ) 4 39251 2 Snap ring 5 20891 2 Bearing 6 100 5305 2 Pinion gear 7 39414 2 Bearing 8 100 5306 4 Shim 9 -------- 1 Casting 10 5732[...]
-
Seite 54
54 Part s MAN08 10 (9/24/2009) WING & CENTER GEARBOX ASSEMB LY[...]
-
Seite 55
Part s 55 MAN081 0 (9/24/20 09) WING & CENTER GEARBOX ASSEMBLY REF P ART QTY DESCRIPTION A 1032298 1 Complet e gearbox (Center & Lef t wing) - or - A 1032297 1 Complete gearb ox (Right w ing) 1 NS 1 Gearbox hous ing 2 571 50 * M8 x 1.2 5 x 14 mm HHCS 3 57076 1 1/2 V ent plug 4 57139 1 Cove r 5 57328 1 Shim kit 60.3 x 71.7 6 1009096 1 Crown [...]
-
Seite 56
56 Part s MAN08 10 (9/24/2009) CENTER DECK DRIVE ASSEMBLY REF P ART QTY DESCRIPTION A 1032185 1 Complete Cen ter Drive Assembl y 1 1029929 1 Y oke, 1-3/8, 6 S pline 2 154 2 Cross & Beari ng Kit 3 40573 2 Inboard Y oke 4 40583 1 Outer Pro file 5 40775 2 S pring Pin , 10 x 65 6 1029928 1 Friction Clu tch 1240, 100Nm 7 57431 1 Flange Y oke REF PAR[...]
-
Seite 57
Part s 57 MAN081 0 (9/24/20 09) CV DRIVE ASSEMBL Y R E F P ART QTY DESCRIPTION A 103218 9 1 Comp lete CV d rive 1 1985 1 1 Slide lo ck rep air kit 2 103228 9 1 Y oke QD CV 1-3/8 - 6 3 103229 0 2 CV U-Joi nt repa ir kit Cat 4 35E 4 103229 1 1 CV Body with fittin g 5 103229 2 1 Y oke and shaf t CV 1. 31-20 spli ne 6 102463 6 2 Drive shiel d bearing k[...]
-
Seite 58
58 Part s MAN08 10 (9/24/2009) WING DRIVE AS SEMBLY (W ALTERSCHEID) REF P ART QTY DESCRIPTION A 1032186 Comp lete Wing Drive Asse mbly 1 40571 1 Y oke, 1-3/8, 6 S pline 2 40589 1 Slide Colla r Kit 3 154 2 Cross & Beari ng Kit 4 40775 2 S pring Pin 5 40573 1 Inboard Y oke 6 1029931 1 Outer Profile & S leeve 7 40592 1 Inner Prof ile 8 40572 1[...]
-
Seite 59
Part s 59 MAN081 0 (9/24/20 09) WING DRIVE ASSEMBL Y (BODIOLI AND P A VESI) REF P ART QTY DESCRIPTION 1 NSS -- Clutc h Assembly (Orde r 1032186) 2 10 329 52 2 U-Jo int R epair Kit 5 0 Se ries C ap Zerk 5 NSS -- Outer T u be and Y oke (Order 10321 86) 8 * 1 10mm x 70mm S pirol Pin 12 NSS -- Outer Profile T ube (Order 1032 186) 13 NSS -- Inner Profil[...]
-
Seite 60
60 Part s MAN08 10 (9/24/2009) 5-BOLT WHEEL & TIRE ASSEMBLY REF PART Q T Y DESCRIPTION 1 1017050 1 Heavy h ub assembl y (incl ude s item s 1 th ro ugh 15 ) 2 1017034 1 Heavy whe el hub with cups (includ es items 6, 7,14) 3 1017033 1 Axle 4 1017027 1 Seal 5 1017028 1 Bearing con e 6 1017036 1 Bearing cup 7 1017037 1 Bearing cup 8 1017029 1 Beari[...]
-
Seite 61
Part s 61 MAN081 0 (9/24/20 09) RUBBER SHIELDING - CENTER SEC TION (STANDARD) (FRONT & REAR) R E F P ART QTY DESCRIPTION 1 1032271 1 Front Cent er Belt Shield Pl ate 2 1032272 1 Front Right Be lt Shield Pl ate 3 1032273 1 Front Lef t Belt Shiel d Plate 7 1032281 2 Bent Lin k .18 x 13.00 8 1032282 2 Bent Lin k .18 x 9.50 9 1032283 2 Rubber Shi e[...]
-
Seite 62
62 Part s MAN08 10 (9/24/2009) RUBBER SHIELDING - WING (ST ANDARD) (FRONT & REAR) R E F P ART QTY DESCRIPTION 4 103227 4 1 Front Right Wind Belt Shiel d Plate, Inner - or- 4 103 2275 1 Fr ont Left Wing Belt Shi eld Plat e, Inner 5 103227 6 1 Front Right Wing Belt Shiel d Plate, Middle - or- 5 103 2277 1 Fr ont Left Wing Belt Shi eld Plat e, Mid[...]
-
Seite 63
Part s 63 MAN081 0 (9/24/20 09) CHAIN SHIELDING - CENTER SECTION (OPTIONAL) (FRONT & REAR) R E F P ART QTY D ESCRIPTION 1 1032241 1 Front Cente r Chain Plate 2 1032242 1 Front Right Cha in Plate 3 1032243 1 Front Lef t Chain Pl ate 4 1032251 2 Rear Chain Plate, Inne r 5 1032252 2 Rear Chain Plate, Out er 10 1007852 2 Pin, 9 to 1 1 Chains 1 1 10[...]
-
Seite 64
64 Part s MAN08 10 (9/24/2009) CHAIN SHIELDING - WING (OPTIONAL) (FRONT & REAR) REF P ART QTY DESCRIPTION 6 1032244 1 Front R ight Wing Chai n Plate, In ner - Or- 6 1032245 1 Front Le ft Wing Chain Plate , Inner 7 1032246 1 Front Right Wing Chai n plate, Midd le - Or- 7 1032247 1 Front Left Wing Chain Plate , Middle 8 1032248 1 Front R ight Win[...]
-
Seite 65
Part s 65 MAN081 0 (9/24/20 09) HYDRAULIC CYLINDERS Wing 3 x 10 Center 3 x 8 REF PART PART QTY DESCRIPTION 2 19810 19810 4 Seal rep air kit (include s 2A thru 2G ) - or - - or - 2 19810H D 19810HD 4 Seal kit w/ heavy duty piston seal 2A ‡ ‡ 1 Wiper seal 2C ‡ ‡ 2 1-1/4 ID U-Cup 2D ‡ ‡ 2 Barrel O-ring 2E † † Rod static O-rin g 2F ‡ [...]
-
Seite 66
66 Part s MAN08 10 (9/24/2009) HYDRAULIC CYLINDER ST ROKE CONTROL KIT CROSSBAR PULLER (OPTIONAL) REF P ART QTY DESCRIPTION 1 24098 1 S troke control set for 1-1/4" c ylinder rod (cont ains ite ms 2 - 5) 2 – – – – 2 1-1/2" Segm ent 3 – – – – 1 1-1/4" Segm ent 4 – – – – 1 1" Segment 5 – – – – 1 3/4&[...]
-
Seite 67
Part s 67 MAN081 0 (9/24/20 09) WINCH KIT (OPTIONAL) REF PART QTY DESCRIPTION A 1019456 - Winch kit, co mplete 1 52478 4 Idler bracket 2 6696 2 Chain idler casting 3 4 09 2 Cl evis pin , 1/2 x 2 4 2241 1 2 Klik pin , 3/16 x 1 5 3379 * - HHCS, 1/2 NC x 1 -1/2 GR5 6 1 1900 * - Lock nut, 1/2 N C flanged 7 1863 * - Wa sher , 1 " SAE flat 8 1 00832[...]
-
Seite 68
68 Appendix Bolt T orque & Siz e Charts (Rev . 3/28/2007) BOLT T ORQUE CHART Always tighten har dware to these values unles s a different tor que value or ti ghtening p roce dure is li sted for a sp ecific applica tio n. F asteners mus t alwa ys be repla ced with t he sam e grade as sp ecifi ed in t he manual par ts list. Always use the proper [...]
-
Seite 69
Appendix 69 Bolt T orque & Siz e Charts (R ev . 3/28/2007) BOLT SIZE CHART NOTE: Chart s hows b olt thr ead s izes an d corr espond ing he ad (wren ch) sizes f or standa rd SA E and metric bolts. ABBREVIATIONS AG ..... .......... .......... ......... .......... .......... ........ Agri culture ASABE ............ ........ American Soci ety of Ag[...]
-
Seite 70
70 Index MAN0810 (9/24/2009) INDEX A ADJUSTMENTS Cutting Hei ght 15 ASSEMBLY Dealer Set- Up Instr uctions 34 Fill Gearbo xes 34 D DEALER CHECK LI ST Check List s Deliv ery (Dealer’ s Respons ibility) 43 Pre-D el iver y (D eale r’ s Resp ons ibil ity ) 43 DEAL ER SERVI CE Crossb ar Install ation 32 Removal 31 Gearbo x Mainten ance Horizo ntal Sh[...]
-
Seite 71
F-3079 (Rev . 3/31/2010) W oods Equipm ent Company 260 6 South Illinois Route 2 Post Office Box 1000 Oregon, Illi nois 61061 USA 800-319-663 7 te l 800 -399- 663 7 fa x www .W oodsEquip ment.com W ARRANTY All Models Except Mow ’ n Machin e TM Zero-T urn Mo wers Plea se En ter In fo rma tion B elow an d Save for F utu re R efer ence . Date P urch [...]
-
Seite 72
F-8494 (Rev . 6/ 23/2005) ©2008 Woods Equipment Company . All rights reserved. WOODS and the Woods logo are trademarks of W oods Equipment Company . All oth er trademarks, trade names , or service mark s not owned by Woods Equipm ent Company that appear in this manual are the propert y of t heir respect ive companies or mark holders. S pecificat i[...]