Deutsch dropdown-ico

Woods Equipment MD80-2 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Woods Equipment MD80-2 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Woods Equipment MD80-2, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Woods Equipment MD80-2 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Woods Equipment MD80-2. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Woods Equipment MD80-2 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Woods Equipment MD80-2
- Den Namen des Produzenten und das Produktionsjahr des Geräts Woods Equipment MD80-2
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Woods Equipment MD80-2
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Woods Equipment MD80-2 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Woods Equipment MD80-2 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Woods Equipment finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Woods Equipment MD80-2 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Woods Equipment MD80-2, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Woods Equipment MD80-2 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    OP E R A TO R ' S M A NU A L R OTAR Y CUTTER 15914 Rev . 5/1 1/2007 T ested. Prove n. Unbeat able . D80-2 MD80-2[...]

  • Seite 2

    2 Introduction Gen’l (Rev . 2/5/2 007) T O THE DEALER: Assemb ly and prop er installati on of this product is the respons ibil ity of the Woods ® dea ler . Read manua l instruc tions and safet y rules . Mak e su re all items on the Dealer ’s Pre-Del ivery and Deliver y Check Lists in the Ope rator ’s Manual are com pleted before r eleasin g [...]

  • Seite 3

    Introduction 3 15914 (R ev . 3/23/2007 ) T ABLE OF CONTENT S INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICA T IONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORM ATION . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

  • Seite 4

    4 Introduction 15914 (R ev . 3/23/2007) SPECIFICATIONS D80- 2 (T owe d) MD80 -2 ( Moun ted ) Cutting Width 80" 80" Cutting Height 2" - 1 4" 2" (Limi ted by tractor li ft) Over all Wi dth 83" 83" Cutter Bl ade Sp indle s 2 2 Blade T ip Speed 14,4 00 14,400 V- B e l t s 3 3 F rame work Chan nel 5/16 " 5/16 &quo[...]

  • Seite 5

    Safety 5 Saf ety Video Orde r Fo rm (2/23/2005) Free Mower Safety V ideo Fill out and return the o rder form and we will send you a FREE VHS or DVD video outlinin g Industrial and Agricu ltural Mower Safe ty Practices. The 22 minute video, developed in co operation with AEM (Association of Equipment Manufacturers), reinforces the proper procedures [...]

  • Seite 6

    6 Sa fety Safe ty Video O rder F orm (2/23/2 005) Free Mower / Cutter Sa fety Video Order Form ✔ (Sel ect one)  VHS Forma t - V HS01052 Sa fety V ideo  DVD Format - DVD 01052 Safety V id eo Please send me Name: _______ _____ _______ ____ _______ _____ _____ Phone: _______ ____ _______ Address: __ _______ ____ _______ _____ _______ _____ ___[...]

  • Seite 7

    Safety 7 D80 Sa fety Rules (Rev . 3/23/2007) TRAINING  Saf ety i nstru cti ons ar e im port a nt! R ead al l att achment and power unit manuals; follow all safety ru les and safety d ecal i nformat ion. (Rep lace- ment manua ls and safety d ecals ar e avai lable f rom your dealer . T o locate you r nearest d ealer , check the Dealer Locator at w[...]

  • Seite 8

    8 Safety D80 Safe ty Rules (R ev . 3/23/2007 ) (Safety R ules co ntinued fr om prev ious p age)  Air in hyd raulic s ystems can cause erratic oper- ation and allows loads or equipme nt components to drop unexpectedly . When connecting equipment or hoses or performing any hydraulic maintenance, purge any air in hy draulic syst em by oper ating al[...]

  • Seite 9

    Safety 9 D80 Sa fety Rules (Rev . 3/23/2007)  Do not modify or alter or permit anyone else to modify or alter the equipme nt or any of its compo- nent s in any way .  Always wear relatively tight and belted clothing to avoid entanglement in moving p art s. W ear sturdy , rough-soled work shoes an d protective equipment for e yes, hair , hands[...]

  • Seite 10

    10 SAFETY 15914 (R ev . 3/23/2007 ) 13 7 11 7 11 9 8 9 12 11 7 10 5 6 12 6 5 3 2 4 1 CD3 8 17A MOU N TED DRI V E PULL-TYPE O N LY PULL-TYPE O N LY FRAME FOR MOU N TED & PULL-TYPE PULL-TYPE O N LY 1 - SERIAL NUMB ER PLATE 540 RPM W ARNING 18866-D 4 - 188 66 F ALLING OFF CAN RESUL T IN BEING RUN OVER.  T ractor must be equipped with ROPS (or R[...]

  • Seite 11

    SAFETY 11 15914 (R ev . 3/23/ 2007) W ARNING TO A VOID SERIOUS INJUR Y OR DEA TH:  Read Operator's Manual (available from dealer) and follow all safety precautions.  Keep all shields in place and in good condition.  Operate mower from tractor seat only .  Lower mower , stop engine and remove key before dismounting tractor .  All[...]

  • Seite 12

    12 SAFETY 15914 (R ev . 3/23/2007 ) SAFETY & INSTR UCTIONAL DECALS A TTENTION! BECOME A LERT! Y OUR SAFETY IS INV O L VED! Replace Immediatel y If Dama ged! ROT A TING BLADES AND THROWN OBJECTS  Do not put hands or feet under or into mower when engine is running.  Before mowing, clear area of objects that may be thrown by blade.  Keep [...]

  • Seite 13

    Operation 13 15914 (R ev . 3/23/2007 ) OPERATION The des igned and tested s afety of this ma chin e depends on i t bei ng ope rated wi thin the lim itations as explain ed in this manual . Be famili ar wit h and follow all safety rul es in the manual , on the cutter a nd on th e tractor . The safe operatio n of this cutter i s the res ponsi bility o[...]

  • Seite 14

    14 Operation 15914 (R ev . 3/23/2007) Driveli ne Att achme nt Attach the c utter to the trac tor 3-po int hi tch (or q uick hitch if av aila ble). Do not attach dri veline. Ra ise an d lower c utter to determi ne max imum an d min imum dis- tance between the tr actor PTO shaft and the gearbox input sh aft. If the distance is too lar ge, the dr ivel[...]

  • Seite 15

    Operation 15 15914 (R ev . 3/23/2007 ) 7. Repeat ste p 6 for the other half of the driv e. 8. File an d clean c ut end s of bo th drive halves . Do not use tr actor if p roper dri veline en gagemen t can- not be obtaine d through these m ethods. Connect dr ivelin e to tractor PT O shaft, maki ng sure th e spring -acti vated loc king coll ar slid es[...]

  • Seite 16

    16 Operation 15914 (R ev . 3/23/2007) Connect c utter drive line to tract or PTO shaft, making sure the s pring -activ ated loc king pin s lides freel y and is seated fi rmly i n tractor PTO spli ne groov e. Adjust H- frame bear ing heigh t to en sure fro nt drivel ine is parall el to grou nd. Remove parking jack from tong ue. Attach to fram e rail[...]

  • Seite 17

    Operation 17 15914 (R ev . 3/23/2007 ) Under certain c onditions , tractor tires m ay roll s ome material do wn and pr event it fr om being cut at th e same height as the surroundi ng area. When this occurs, r educ e tracto r groun d speed bu t main tain 540 rpm PTO speed. Th e lowe r speed will pe rmit material to at le ast partially rebound . Und[...]

  • Seite 18

    18 Owner Service 15914 (R ev . 3/23/2007) OWNERS SERVICE  On pull-type unit s, a pin is installed to prevent the height adjustment crank from det aching. Do not operate or service unit unless pin is inst alled.  Before performing any service or maintenanc e, lower equipmen t to ground or block se curely , turn off engine, remove key , and dis[...]

  • Seite 19

    Owner Service 19 15914 (R ev . 3/23/2007 ) Figure 8 . Lubric ation Points Blade R emoval Rotate cros sbar u ntil b lade pin a ssemb ly is direc tly below ac cess h ole i n rea r of c utter fra me. Re move bol t (1) an d bla de pin clip (2). S lide keyho le pl ate (3) out o f blade pi n groov e and remov e. Remo ve spacers and drive pin out of cross[...]

  • Seite 20

    20 Owner Service 15914 (R ev . 3/23/2007) NOTICE ■ If blade pin is sei zed in c rossbar a nd ext reme force will be required to remove it, support c ross- bar from below to prevent damage to spindle.  Y our dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous. Blade[...]

  • Seite 21

    Owner Service 21 15914 (R ev . 3/23/2007 ) SERVICING TI RES S AFELY Used Aircraft T ires (Figure 10) Do not attemp t to mou nt a tir e unle ss you hav e the proper equ ipment and ex perienc e to pe rform the job. Always maintain the correc t tire pressur e. Do not inflat e tires above the recommen ded press ure. Never weld or heat a w heel and ti r[...]

  • Seite 22

    22 Dealer Service 15914 (R ev . 5/1 1/2007) DEALER SERVICE  On pull-type unit s, a pin is installed to prevent the height adjustment crank from det aching. Do not operate or service unit unless pin is inst alled.  Before performing any service or maintenanc e, lower equipmen t to ground or block se curely , turn off engine, remove key , and d[...]

  • Seite 23

    Dealer Service 23 15914 (R ev . 5/1 1/2007) Inspect gear sh afts and sl eeves. P ay spe cific a ttentio n to a reas w here seal s seat . Ch eck f or crac ks, groove s, nicks or bumps. If da mage cann ot be repair ed by resur - facing with e mery c loth, rep lace dama ged part. Inspect ho usings fo r damage, payi ng specifi c attentio n where s eals[...]

  • Seite 24

    24 Dealer Service 15914 (R ev . 5/1 1/2007) Proper bearing adjustme nt is e ssentia l to goo d bear ing life. Do n ot lea ve be aring ad juste d too tigh tly . B earings should tu rn freel y without any n oticea ble end pl ay . When t he bearin gs are ad juste d, coat area o f spindl e housing where sea l sea ts with Perm atex an d pre ss seal ( 4)[...]

  • Seite 25

    Dealer Service 25 15914 (R ev . 5/1 1/2007) Figure 14 Figure 15 Figure 16 Figure 17 2. With snap rings re moved, support dr ive in vi se, hold y oke in hand and tap o n yo ke to dri ve cup up out of yok e. Se e Figure 15 . 3. Clamp cup in v ise as s hown i n Figure 1 6 and ta p on yoke to c omplet ely re move c up from yoke. Repeat ste ps two and t[...]

  • Seite 26

    26 Dealer Service 15914 (R ev . 5/1 1/2007) yoke s sharp ly with a hammer to reli eve an y ten- sion. R epeat unt il both yok es mov e in all dir ections without restri ction . Figure 18 SERVICING TI RES SAFELY Used Aircraft T ires (Figure 19) Do not attemp t to mou nt a tire u nless y ou hav e the proper equ ipment and ex perienc e to pe rform the[...]

  • Seite 27

    Dealer Service 27 15914 (R ev . 5/1 1/2007) TROUBLE SHOOTING * Check bel t for damage by laying it fl at on floor . If belt does not li e flat (has humps or twists) this indicates br oken or stretch ed cords . Repl ace be lt. PROBLEM P OSSIBLE CAU SE SOLUTION Does not cut Dull blade s Sharpe n blades . Worn or brok en bl ades Repla ce bl ades. (Rep[...]

  • Seite 28

    28 Assembly 15914 (R ev . 5/1 1/2007) ASSEMBLY DEALER SET - UP INSTRUCTIONS The se inst ruct ions are f or t he ass emb ly of t he MD 80 and D80. Ma ny of the proc edures apply to both un its. When an inst ructi on ap plies t o a speci fic u nit, th e sec - tion headi ng wil l indicate which uni t. Assemb ly of this c utter is th e resp onsibil ity[...]

  • Seite 29

    Assem bly 29 15914 (R ev . 5/1 1/2007) Remove th e two rear c arriag e bolts from the left sid e skid. P lace ba ffle (1) under cu tter f rame and attach as shown in Figu re 21. Figure 21 . Distr ibution Baffle Installa tion Gearbox Lubrication NOTICE ■ The gearbox was not filled at the fa ctory . It must be serviced before operating cutter . Fai[...]

  • Seite 30

    30 Assembly 15914 (R ev . 5/1 1/2007) Wheel Y o ke Inst alla tion for D80-2 Pull-T ype Cutter The wheel yoke for use with pneum atic tires is illus - trated. Th e spring-l oaded whe el yoke ins talls the same . Attach wheel y oke (6) to rear of c utter fra me with cl evis pins (15) and cotte r pins (3) at two poi nts. Insert cran k (1 1) through pi[...]

  • Seite 31

    Assem bly 31 15914 (R ev . 5/1 1/2007) Fig ure 24 . T ong ue and H-Frame Assem bly T ongue Instal lation fo r D80-2 Pull-T yp e Cutter Attach co mpress ion br acket (7 ) to fr ont of ge arbox stand with lock washers (20) and nu ts (21), see Figu re 24. Align hol es in tongue (1) to botto m hole of ma st plat e (6) and ins ert bushing ( 14) throu gh[...]

  • Seite 32

    32 Assembly 15914 (R ev . 5/1 1/2007) chain (32 ) around the compres sion link to prevent driv - eline sh ie ld ro tation. Align d rive line in H-frame and in sert clev is pin (22) through H-fr ame and car rier bear ing (9). At tach by ins ert ing t wo c otte r pi ns (1 7) i n cle vis pin (22) . Sn ap middle teth er chain (32) ar ound H-fra me to p[...]

  • Seite 33

    Assem bly 33 15914 (R ev . 5/1 1/2007) Figure 26 . Assem bly of MD80 (Mou nted Mo del) MD80 Assembly Driveline Installation Loosen c lamp bo lt (35) on rear hal f of drive, se e Figu re 26. Install k ey (33 ) in gearb ox keyw ay and sli de driv e onto ge arbox inpu t shaft. Ins tall cotter key (38) an d tighten c lamp bo lt. Sn ap teth er cha in (4[...]

  • Seite 34

    34 Assembly 15914 (R ev . 5/1 1/2007) Bolt reb ound pad (2 8) to reb ound pad su pport (27). Insert bo lt (9) thro ugh gears tand and br acket (2 6), then place reboun d pad assem bly on top and s ecure wit h lock nu ts (10) . Attach tailwhe el arm b rackets (19) to brack ets on rear of cutter frame with bolts (22) and elastic stop nuts (21) . Atta[...]

  • Seite 35

    Assem bly 35 15914 (R ev . 5/1 1/2007) OPTIONAL CHECK CH AIN INST ALLATION Att ach chain (9) t o cutter mast pl ate (2) with bolt (1), washer (3) and nut (4) as shown. Repeat for op posite mast plate . Attach on e check chain brack et (7) to each si de of th e tractor to p link bracke t (6) with bolt ( 5) and nut (8) as shown. The check c hains may[...]

  • Seite 36

    36 Dealer Check Lists 15914 (R ev . 5/1 1/2007) DEALER CH ECK LIST S PRE- DELIVERY CH ECK LIST (DEA LER’S R ESPO NSIBIL IT Y) Inspect cutte r thorough ly after asse mbly to be certain it is set up properl y before deliver ing it to c ustom er . The following chec k lis t is a remind er of poi nts to in spec t. Check off each item as it is f ound [...]

  • Seite 37

    Part s 37 15914 (R ev . 3/23/2007 ) INDEX TO P A RT S LIST D80-2 (Pull -T ype) Main F rame Assemb ly (Pull- T ype) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38 Mai n F rame A ssem bly - Co m mon Par ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pa ge 4 0 F ront 2 /3 of 3 -Join t Dr ive[...]

  • Seite 38

    38 Part s 15914 (R ev . 3/23/2007) D80-2 MAIN FRAME ASSEMBLY (PULL-TYPE) 6 7 10 23 36 37 3 8 35 33 23 39 11 9 25 24 8 26 12 31 32 22 29 32 31 5 2 8 22 30 32 31 27 34 22 4 3 2 1 CD3 8 24A 40 R E F P ART Q TY DESCRIPTION 1 7023 1 T ongue 2 406 1 Compr ession m ember 37 0 3 0 1 H - F r a m e 4 ----- 1 Pa rking jack 5 7035 1 1/2 Sche dule 40 x 3-9/16 p[...]

  • Seite 39

    Part s 39 15914 (R ev . 3/23/2007 ) MD80-2 MAIN FRAME ASS EMBL Y (MOUNTED MODEL) 45 22 32 39 37 42 40 3 8 43 44 41 36 29 36 29 35 35 34 33 31 30 2 8 27 26 25 24 23 22 22 22 12 11 10 9 8 7 6 5 4 3 2 1 CD3 8 25 R E F P ART QTY DESCRIPTION 1 31581 2 Inside hitch br ace 2 27938 2 A-F r ame hal f 3 28236 1 Lift arm channe l ass embl y 4 29071 1 Hitch s [...]

  • Seite 40

    40 Part s 15914 (R ev . 3/23/2007) D80-2 & MD80- 2 MAIN FRAME ASSEMBLY - COMMON PARTS 2 3 4 4 0 51 4 8 57 55 41 4 11 1 2 50 6 1 3 4 3 4 6 2 6 50 47 4 7 49 4 16 22 45 2 3 2 1 24 25 52 57 1 4 56 56 58 53 4 3 5 1 54 1 7 8 2 0 CD3855 27 - Comp lete Englis h Deca l Set 28 - French Safety De cal Set 29 - Eng lish Sa fety Decal S et[...]

  • Seite 41

    Part s 41 15914 (R ev . 3/23/2007 ) D80-2 & MD80- 2 MAIN FRAME ASSEMBLY - COMMON PARTS R E F P ART QTY DESCRIPTION 1 ----- 1 Deck (not sold separatel y) 2 28219 1 Rear drive shield 3 15818 1 Right v-belt sh ield 4 28230 1 T ake-up rod idler 5 3444 2 Acce ss ho le co ver 6 28225 1 Gearbox s tand 7 28203 1 T ower acces s cover 8 1942 1 Gearbox an[...]

  • Seite 42

    42 Part s 15914 (R ev . 3/23/2007) D80-2 FRONT 2/3 OF 3-JOINT DRIVE (SQUARE SHAFT) 22 23 2 21 21 14 1 - - COMPLET E DRI V E 20 20 12 3 19 1 8 17 16 10 15 13 11 9 8 7 6 3 4 5 CD3 8 73B N OTE: T w os t y l e so fd r i v eshafts ha v e b een u s e do nt h eD 8 0s e r i e sc u tters. Check yo u rd r i v eshaft for s qu are or t w o- -l o b e shaft and [...]

  • Seite 43

    Part s 43 15914 (R ev . 3/23/2007 ) D80-2 FR ONT 2/3 OF 3-JOINT DRIV E (TWO -LOBE SHAFT) 2 3 4 5 6 7 8 9 4 13 C D 5963 12 12 NOTE: T wo styles of driv eshafts hav e been used on the D80 series cutters . Check your driv eshaft for square or two - - lobe shaft and or der repair par ts from the correct parts lis t. R E F P ART QTY DESCRIPTION 1 44919 [...]

  • Seite 44

    44 Part s 15914 (R ev . 3/23/2007) MD80-2 FRONT 1/2 OF UNIVERSAL DRIVE D80-2 & MD80 -2 REAR SECTION OF UNIVERSAL DRIVE 5 8 1 1-3/ 8 SPLI N E 7 6 4 3 2 CD3 8 72 Ref Part N o N o N o Used Description 1 19064 1 Front half of 2-joint dri v e, complete 21 1 51 1 - 3 / 8 , 6-T ooth spline, qu ick disconnect U-joint yoke 3 1 10 1 Uni v ersal joint rep[...]

  • Seite 45

    Part s 45 15914 (R ev . 3/23/2007 ) D80-2 & MD 80-2 GE ARBO X ASSEMBLY Ref Part No No No Used Description A 6222 1 1:1 Gearbox assembly complete 1 213 1 Seal for 1-3/4 shaft 2 20 9 1 1 -1/ 2 x 1 -3/ 4 x 1 -3 /8 S le e ve 3 255 1 Ring seal 4 21 1 4 Bearing cone 2788A 5 210 4 Bearing cup 2720 6 6226 1 V ertical gear shaft housing with cups 7 207 [...]

  • Seite 46

    46 Part s 15914 (R ev . 3/23/2007) D80-2 & MD80- 2 BLADE SPINDLE ASSEMBLY D80-2 & MD80- 2 BLADES 20 10 19 1 8 17 16 15 14 13 12 11 6 7 8 9 8 7 6 54 3 2 1 CD3 8 31 R E F P ART QTY DESCRIPTION 1 15805 1 S pindl e assem bly 2 7143 1 S pi ndle hous ing with bearing c up s and gr ease fitt ing 3 7269 1 3/8 NF x 3/8 Set s crew 4 7127 1 5/16 x 5/3[...]

  • Seite 47

    Part s 47 15914 (R ev . 3/23/2007 ) D80-2 & MD80-2 CHAIN SHIELD ING ASSEMBL Y CD3836A 1 2 5 6 6 18 18 17 4 3 19 20 1 R E F P ART Q TY DESCRIPTION 1 29085 2 Chain sh ielding c omplete (does not includ e items 6 & 17) 2 29086 4 Chain pl ate assem bly ( does not includ e items 6 & 17) 3 29087 4 Chain sh ield p late 4 1007850 4 Pin, 31 to 3[...]

  • Seite 48

    48 Part s 15914 (R ev . 3/23/2007) D80-2 & MD80- 2 IDLER PULLEY ASSEMBLY D80-2 PARKING JACK R E F P ART QTY DESCRIPTION 1 5586 1 Idler assembly comp lete 2 378 1 5/8 NC x 5 HHCS GR2 3 843 1 1/2 x 2 x 2 Sq uare was her 4 844 2 Seal retain er 5 845 2 Felt seal 6 7016 1 Idler w ith beari ngs 7 232 2 Nee dle bear in g 8 ----- * 1 Grease fitting 9 3[...]

  • Seite 49

    Part s 49 15914 (R ev . 3/23/2007 ) D80-2 H EIGHT ADJUST MENT C RANK D80-2 SPRING-L OADED WHEEL YOKE DB956A R E F P ART QTY DESCRIPTION 1 15804 1 Height ad justmen t crank 2 1 1880 1 5/16 x 1-3/ 4 S piro l pin 3 10417 1 Height ad justmen t pivo t block 4 189 3 1 Thr ust be ar ing 5 1863 2 1" SAE Flat washe r 6 589 5 1 Heig ht a djus tment piv [...]

  • Seite 50

    50 Part s 15914 (R ev . 3/23/2007) D80-2 LAMINA TED TI RE WITH HUB & AXLE D80-2 RIM & AXLE ASSEMBLY 23 19 15 16 17 18 21 22 14 13 11 7 8 10 2 8 7 6 5 4 3 1 Ref Part No No No Used D escription 1 9373 1 6.00 x 9 Laminated tire w/hub & axle 2 4984 1 Heavy hub with long axle 3 3626 1 1 - -14 UNS Hex nut 4 3689 * 1 1” Standard lockwasher 5[...]

  • Seite 51

    Part s 51 15914 (R ev . 3/23/2007 ) D80-2 AIRCRAFT TIRE & HUB 10 9 19 17 1 8 20 21 10 SO L I D T IRE &R I M 27 10 26 20 21 22 10 1 25 24 23 16 15 9 8 7 6 5 4 3 2 RIM F OR PNEUMAT I C TIRE AIRCRAFT TIRE & R IM CD4574 R E F P ART Q TY DESCRIPTION 1 12080 1 S tan dard hu b with l ong axle 2 2307 1 Hub with cups 3 12081 1 Wing ax le assem b[...]

  • Seite 52

    52 Part s 15914 (R ev . 3/23/2007) MD80 -2 T A ILWHEE L ASSE MBLY 16 15 12 17 1 8 19 11 10 7 8 9 9 8 7 6 20 22 21 14 23 5 13 5 23 4 3 2 1 CD3 8 3 2 24 R E F P ART QTY DESCRIPTION 1 1 5783 1 T ailw heel ar m asse mbly (inc lude s items 5 & 13) 2 1 5270 1 T ailw heel cle vis 3 15591 1 Wheel hub with cup s incl udes i tems 9 & 13) 4 4676 1 4.0[...]

  • Seite 53

    Part s 53 15914 (R ev . 3/23/2007 ) D80-2 PIV OT LINK KIT (OPTIONAL) D80-2 HYDRAULIC HOSE KIT & FITTINGS (OPTIO NAL) R E F P ART QTY DESCRIPTION 1 875 1 1 Pivo t li nk ki t 2 12 305 * 1 1/2 x 5-1/ 2 HHCS GR5 3 3443 1 Hydraulic hose hol der 4 1093 1 1/2 NC Hex nu t 5 15792 1 Pivot link 6 ----- 1 Cylind er (see p age 54 7 ----- 1 Crank (s ee pag [...]

  • Seite 54

    54 Part s 15914 (R ev . 3/23/2007) D80-2 3-1/2 X 8" HYDRAULIC CYLINDER #10475 (OPTIONAL) DC1 105 R E F P ART Q TY DESCRIPTION 1 ----- - Not availab le 2 26340 1 Seal kit (include s 2A thr u 2G) 2A † 1 1-1/4 ID Wi per seal 2B † 1 Rod back -up ring 2C † 2 1-1/4 I D O-r ing 2D † 2 3/16 x 3 -1/2 OD O-ring 2E † 1 3/32 x 3/4 O D O-ri ng 2F[...]

  • Seite 55

    Part s 55 15914 (R ev . 3/23/2007 ) D80-2 & MD80-2 LEAF MULC HER ASSEMBLY (OPTIONAL) MD80-2 CHECK CHAIN ASSEMBLY (OPTIONAL) Ref Part N o N o N o Used Description 1 8 757 1 Leaf m u lcher complete 2 290 8 9 1 Leaf m u lcher adapter 3 129 8 1 Front shield 4 1579 8 1 Right angle leaf m u lcher 5 15797 1 Rear leaf m u lcher 6 15799 1 Left side angl[...]

  • Seite 56

    56 Part s 15914 (R ev . 3/23/2007) MD80-2 CATEGORY 2 HIT CH PIN OPTIONS MD80-2 CATEGORY 2 B USHING KIT Ref Part No No No Used Description 1 13010 1 Category 2 hitch pin mounting kit 2 12275 2 Category 2 mounting pin, 6” long 3 1266 * 2 3/16 x 1 -1/2 Cotter pin 4 1301 1 2 7/8 x 2-3/8 x 3/16 Flat washer 5 13012 2 7/8 NF Castle hex nut 6 7372 1 25/3[...]

  • Seite 57

    Appendix 57 Bolt T orque & Size Ch arts (Rev . 3/28/2007 ) BOLT T ORQUE CHART Always tighten har dware to the se values unles s a di ff erent t orque value or tighten ing pro cedure i s list ed for a specifi c applica tio n. F a stene rs must al wa ys be re placed wi th the s ame grade as specifi ed in the manual par ts list. Always use the pro[...]

  • Seite 58

    58 Appendix Bolt T orque & Size Charts (R ev . 3/28/2007 ) BOLT SIZE CHART NOTE: Chart s hows b olt thr ead s izes an d corr espond ing he ad (wren ch) sizes f or standa rd SA E and metric bolts. ABBREVIATIONS AG ..... .......... ....... ...... .......... ....... .......... ...... . Agriculture ASABE . ............ ....... American Socie ty of [...]

  • Seite 59

    Index 59 15914 (R ev . 3/23/ 2007) INDEX ASSEMBLY 28 Dealer Set-Up Instr uctions 28 Blade Ins talla tion 2 8 Chain Shi elding In stall ation 29 Distributi on Baff le Inst allation 28 Gearbo x Lubri cation 29 MD80 Assemb ly 33 Optional Hy draulic Installa tion for D80-2 Pul l- Type Cutter 32 Tongue Ins tallation for D80-2 Pull -Type Cutt er 31 Wheel[...]

  • Seite 60

    F-3079 (Rev . 1/16/2007) W oods E quipment Company 260 6 South Illinois Route 2 Post Office Box 1000 Oregon, Il linois 61061 800-319-663 7 tel 800-3 99-6 63 7 fax www .W oodsEquipment.com W ARRANTY (All Models Except Mow’ n Machine TM Zero-T u rn Mo wers and W oods Boundar y TM Utilit y V eh icles) Please Ent er In form atio n Be low and Save for[...]

  • Seite 61

    F-8494 (Rev . 6/23/2005) W oods Eq uipme nt Company 260 6 South Illinois Ro ute 2 Po st Office Box 1000 Oregon, Illinois 61 061 800-319-663 7 tel 800 -399 -66 3 7 fa x www .W oodsEquipment.com W ARRAN TY (Replacement Parts F or All Models Except Mo w’ n Machine TM Zero-T urn Mo wers and W oods Boundary TM Utility V ehicles) W oods Equipment Co mp[...]

  • Seite 62

    W oods Equipment C ompan y 2 606 South Il linoi s Route 2 P ost Office Bo x 1 000 O regon, Illinois 61061 8 15-732-214 1 tel 8 15-732-758 0 f ax w ww .Wo odsEquipm ent.com 15914 © 1996 Woods Equipment Company . All rights reserved. WOODS, the Woods logo, and "T e sted. Proven. Unbeatable." are trademarks of Woods Equipment Company . All [...]