Woodstock W1680 Bedienungsanleitung

INSTRUCTION MANUAL MODEL W1680 17" DRILL PRESS Phone: 1-800-840-8420 • On-Line Technical Support: tech-support@woodstockint.com COPYRIGHT © 2000 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China[...]

Table Of Contents PAGE 1. INTRODUCTION ................................................................................2 ABOUT YOUR NEW DRILL PRESS ......................................................2 WOODSTOCK SERVICE AND SUPPORT ................................................2 WARRANTY AND RETURNS .............................................[...]

- 2 - INTRODUCTION ABOUT YOUR NEW DRILL PRESS This new Shop Fox ® Drill Press has been specially designed by Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail, ruggedly built parts and a rigid quality con- trol program assure safe and reliable operation. The Model W1680 Drill Press is capable of[...]

- 3 - WARRANTY AND RETURNS Woodstock International, Inc. warrants all SHOP FOX ® machinery to be free of defects from workman- ship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of mai[...]

- 4 - READ MANUAL BEFORE OPERATING MACHINE FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY SAFETY FIRST! 1. Thoroughly read the instruction manual before operating your machine. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, convenient place for future reference. 2. Keep work ar[...]

1. Always operate your drill press at speeds that are appropriate for the drill bit size and the mate- rial that you are drilling. 2. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off. 3. Make sure the drill bit you are using is tightened properly. Use[...]

-6- This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a sep- arate 12 A.W.G. copper grounding wire from the outlet to a known ground. Under no cir- cumstances should the grounding pin from any three-pronged plug be removed. [...]

- 7 - AVOIDING POTENTIAL INJURIES Figure 2. Never drill, holding workpiece by hand. Figure 3. Keep fingers away from spinning tool. Fig. 4. Remove Switch Safety Key when not in use. Figure 5. Unplug machine when changing bulbs. SAFETY[...]

-8- Figure 6. Components laid out for identification. The following is a description of the components shipped with the Shop Fox ® W1680 Drill Press. It is rec- ommended that the components be laid out in a similar fashion to those in Figure 6 . This will help in identification before beginning assembly. Should any part be missing, examine the pac[...]

-9- While the main components of the Shop Fox ® W1680 Drill Press are assembled at the factory, some assembly is required. The following is the recommended sequence best suited for final assembly. TOOLS REQUIRED: You will need a 11 ⁄ 16 " open end wrench, a rubber or wooden mallet and a 5mm Allen ® wrench (supplied). Base/Column 1. Ensure [...]

-10- Figure 11. Correct rack orientation. Figure 9. Insert the pinion gear from the inside. Figure 10. Align setscrew with flat on pinion. Table Support 1. Thread the 12mm table lock handle 3 turns into the table support bracket. 2. Insert the pinion into the hole on the side of the table support bracket from the inside, starting with the pinion sh[...]

-11- Figure 12. Bottom of rack in position. Figure 13. Inside bevel in the correct position. Table Support, Cont. 4. Slide the table support bracket onto the col- umn while holding the rack in place. Allow the bracket to go down until the bottom of the rack contacts the shoulder on the col- umn support. Figure 12. Secure the table with the lock han[...]

Head Stock 1. The bottom of the headstock has a pocket for inserting the column. An assistant will be needed to position the pocket over the column, as in Figure 14. Allow the head- stock to slide down until it stops (approxi- mately 4"). 2. Align the headstock directly over the foot of the base by using a plumb bob. Lay a mea- suring tape or [...]

Figure 16. Tighten setscrews to secure headstock. Figure 17. Installing handles. Figure 17b. Installing a light bulb. Handles Three handles are supplied with your new Drill Press. Thread them into the hub. Figure 17. Installing Light Bulb The Shop Fox ® 17" Drill Press is fitted with a light socket that accommodates standard sized bulbs. Befo[...]

-14- Drill Chuck and Arbor Figure 19. Seating the arbor into chuck. Figure 18. Chuck components identification. The drill chuck is attached to the drill spindle by means of a drill chuck arbor. Matched tapers on the arbor and the back of the chuck create an almost permanent assembly when properly joined. To assemble the drill chuck and mount it to [...]

Figure 20. Seating arbor into spindle. -15- A wedge is included with the Shop Fox ® Drill Press which aids in drill chuck arbor removal. 1. Rotate the spindle handles until a slot is exposed in the side of the quill. 2. Rotate the spindle until the inner slot is aligned with the outer. See Figure 21. You will see through the spindle when slot is p[...]

-16- Speed Change ADJUSTMENTS Unplug the drill press before changing speeds. The Drill Press has 12 speeds ranging from 140 to 3050 RPM. There is a speed chart located under the belt guard and one on the following page. Refer to these while reading these instructions. 1. Loosen the belt tension lock knobs on both sides of the headstock. See Figure [...]

-17- More About Speed Changes Spindle Adjustments Your new drill press comes fitted with a depth stop for use when drilling. Follow the instruc- tions below for use. 1. Loosen the depth collar lock knob. Figure 26. 2. Rotate the depth collar to the desired depth indicated by the scale on the collar. Secure the collar with the lock knob. 3. Test the[...]

-18- Table Adjustments The table can be adjusted for height, rotation and angle. Follow these instructions to adjust height: 1. Loosen the support bracket lock knob. Turn the table hand crank to lift or lower the table. Figure 28. 2. Always lock the support bracket in place before operating machine. Adjust rotation: 1. Loosen the lock handle locate[...]

-19- OPERATIONS Once assembly is complete and adjustments are done to your satisfaction, you are ready to test run the machine. Make sure the starting switch is off. The pad- dle is down for off. Make sure all the fasteners and lock handles are tight. Plug in the power cord. Pull the START paddle. Make sure that your finger is poised over the paddl[...]

-20- Care must be taken to secure the bit firmly in place. When changing bits, proceed as follows: 1. Disconnect the machine from the power source. 2. Open the chuck wide enough to accept a new bit. 3. Install the bit so the chuck jaws will grab as much of the bit shank as it can. Figure 32. Do not allow the chuck to grab the fluted body of the dri[...]

-21- MAINTENANCE Lubrication Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. For other items on this machine, such as the quill, table and column, an occasional applica- tion of light machine oil is all that is necessary. Before applying lubricant, clean off [...]

-22- The following pages contain general machine data, parts diagrams/lists and warranty/return information for your Shop Fox ® Model W1680 17" Drill Press. If you need parts or help in assembling your machine, or if you need operational informa- tion, we encourage you to call our Service Department. Our trained service technicians will be gl[...]

-23- Your Notes:[...]

- 24 - PARTS[...]

-25- 01 X1680001 BASE 02 XPB27M HEX BOLT M12-1.75 X 30 03 X1680003 RACK 04 X1680004 COLUMN 05 X1680005 TABLE BRACKET 06 X1680006 HANDLE 07 X1680007 SET SCREW 08 X1680008 SHAFT 09 X1680009 NUT 10 X1680010 PIN 11 X1680011 WASHER 12 X1680012 BOLT 13 X1680013 TABLE BOLT 14 X1680014 TABLE ARM BRACKET 15 X1680015 TABLE 16 X1680016 CLAMP BOLT 17 X1680017 [...]

53 X1680053 SLIDE BAR 54 X1680054 SLIDE BAR 55 X1680055 MOTOR BASE 56 X1680056 WASHER 56A X1680056A SPRING WASHER 57 X1680057 NUT 58 X1680058 MOTOR 59 X1680059 MOTOR PULLEY 60 X1680060 KEY 61 X1680061 SET SCREW 62 X1680062 V-BELT 63 X1680063 CENTER SHAFT 64 XP6202 BALL BEARING 6202ZZ 65 XP6202 BALL BEARING 6202ZZ 66 X1680066 INTERNAL RETAINING RING[...]

CUT ALONG DOTTED LINE 10. What stationary woodworking tools do you own? Check all that apply. ___Air Compressor ___Panel Saw ___Band Saw ___Planer ___Drill Press ___Power Feeder ___Drum Sander ___Radial Arm Saw ___Dust Collector ___Shaper ___Horizontal Boring Machine ___Spindle Sander ___Jointer ___Table Saw ___Lathe ___Vacuum Veneer Press ___Morti[...]

TAPE ALONG EDGES--PLEASE DO NOT STAPLE FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE WOODSTOCK INTERNATIONAL, INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 Place Stamp Here[...]