ZyXEL Communications IES-1000 Bedienungsanleitung

IES-1000 Integrated Ethernet Switch July 2002 Version 2.04 Hardware Installation Guide[...]

IES-1000 Hardware Installation Guide ii Copyright Copyright IES-1000 Integrated Ethernet Switch Copyright © 2002 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in an y form or by any means,[...]

IES-1000 Hardware Installation Guide ZyXEL Limited Warranty iii ZyXEL Limited W arranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. During the warranty period and upon proof of purchase, should the product ha[...]

IES-1000 Hardware Installation Guide iv Customer Support Customer Support If you have questions about your ZyXEL product or desire assistance, contact ZyXEL Communications Corporation offices worldwide, in one of the following ways: Cont acting Customer Support When you contact your customer support representa tive, have the following information r[...]

IES-1000 Hardware Installation Guide T able of Contents v T able of Content s Copyright .................................................................................................................................................................... ii ZyXEL Limited Warranty .......................................................................[...]

IES-1000 Hardware Installation Guide vi T able of Contents 6.1 System S tartup ................................................................................................................. .......................... 6-1 6.1.1 The SYS LED Does Not Turn On ...........................................................................................[...]

IES-1000 Hardware Installation Guide Lists of Figures, Diagrams and T ables vii List of Figures Figure 1-1 IES-1000 Building Deployment Example ................................................................................ ............... 1-2 Figure 1-2 Enterprise Application .......................................................................[...]

IES-1000 Hardware Installation Guide viii Preface Preface Congratulations on your purchase of the IES-1000 Integrated Ethernet switch. This guide shows you how to set up the hardware for your IES-1000. About the IES-1000 The IES-1000 is an integrated Ethernet switch th at multiplexes traffic from up to 16 G.SHDSL or ADSL subscribers (or eight of ea[...]

IES-1000 Hardware Installation Guide IES-1000 Applications 1-1 Chapter 1 IES-1000 Applications This chapter describes IES-1000 applications an d basic operating environment. 1.1 Applications The following are typical DSL multiplexing applications of the IES-1000. 1. Multiple Tenant Unit (MTU) 2. Enterprise 1.1.1 MTU Application The following figure[...]

IES-1000 Hardware Installation Guide 1-2 IES-1000 Applications Figure 1-1 IES-1000 Building Deployment Example 1.1.2 Enterprise Application The IES-1000 can also be used in any-sized compan y to multiplex traffic from employee G.SHDSL or ADSL connections to the Internet. Multiplex traffic from up to 16 connections and use a hub or switch to multipl[...]

IES-1000 Hardware Installation Guide IES-1000 Applications 1-3 Figure 1-2 Enterprise Application[...]

[...]

IES-1000 Hardware Installation Guide Hardware Installation 2-1 This chapter shows you how to install hardware for a free-standing or rack-m ounted scenario. 2.1 Environment The following are the recommended environments for the IES-1000. 2.1.1 Operating Environment Temperature: 0 — 50°C; Humidity: 5% — 95% (non-condensing) 2.1.2 S torage Envir[...]

IES-1000 Hardware Installation Guide 2-2 Hardware Installation 2.4.1 Att aching the Mounting Bracket s to the IES-1000 Step 1. Position a mounting bracket on one side of the IES-1000, lining up the four screw holes on the bracket with the screw holes on the side of the unit (see the figure shown next). Failure to use the proper screws may damage th[...]

IES-1000 Hardware Installation Guide Hardware Installation 2-3 Figure 2-2 Mounting the IES-1000 on a Rack Step 2. Using a #2 Philips screwdriver, install the M5 flat head screws through the mounting bracket holes into the rack. Step 3. Repeat Step 1 and Step 2 to attach the second mounting bracket on t he other side of the rack.[...]

[...]

IES-1000 Hardware Installation Guide Removing and Installing Network Modules 3-1 This chapter shows you how to remove and install network modules. Each IES-1000 accommodates up to two network modules. Remove and install modules via the front of the IES- 1000. The figure below shows the front view of a SA M1008 network m odule; the procedures for re[...]

IES-1000 Hardware Installation Guide 3-2 Removing and Installing Network Modules Figure 3-3 Removing a Network Module from the IES-1000 Chassis 3.2 Inst alling a Network Module Step 1. Hold the module with the network ports facing you an d insert it into an empty slot located on the front of the IES-1000 as shown next. Step 2. Push the bottom of th[...]

IES-1000 Hardware Installation Guide Removing and Installing Network Modules 3-3 Figure 3-4 Installing a Network Module into the IES-1000 Chassis The front of the network module must be flush with the front of the IES-1000 after you install a network module or it will not work! Step 3. Secure the module to the chassis by turning the tw o screws on [...]

[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-1 Chapter 4 IES-1000 Connections This chapter shows you how and where to make hardware connections. Before you make your hardware connections, make su re that your IES-1000 is safely and securely positioned. 4.1 Front Panel Connections All connections are made on the front panel of th e IE[...]

IES-1000 Hardware Installation Guide 4-2 Hardware Connections Figure 4-2 Console Port Connection 4.3 SHDSL Port Connections The SHDSL ports connect to an MDF (Main Distribution Frame) and end-user equipment via telephone wire. • For detailed specifications about the associated RJ-11 connector, refer to the Pin Assignment appendix. • For more de[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-3 Figure 4-3 SHDSL Port and MDF Connections Step 3. Connect a different telephone wire to the lowe r port of the MDF using a punch-down tool. Step 4. Connect the other (RJ-11) end of the telephone wire to the end-user G.SHDSL modem/router. When you finish this procedure your connections sh[...]

IES-1000 Hardware Installation Guide 4-4 Hardware Connections Figure 4-4 SHDSL Port, MDF and User Equipment Connections Notes About MDFs (Main Distribution Frames) An MDF is usually installed between end-users’ equipment and the telephone company (CO) in a basement or telephone room. The MDF is the point of termination for the outside telephone c[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-5 Figure 4-5 Magnified View of MDF Wiring Connect wiring from end-user equipment to the lower por ts of an MDF using a telephone wire. Connect wiring from the telephone company to the upper ports of an MDF (see the previous figure). Some MDFs have surge protection circuitry built in be twe[...]

IES-1000 Hardware Installation Guide 4-6 Hardware Connections Figure 4-6 AAM1008 Installation Overview You can also use RJ-11 connectors on both ends of the telephone cables connect directly to an ADSL modem(s) or patch panel. This chapter discusses connections using MDFs. 4.4.1 T ypical Scenarios Your existing telephone wiring usually depends on y[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-7 Figure 4-7 Installation Scenario A Procedure T o Connect T o An MDF Step 1. Connect the RJ-11 connector end of a telephone wire to one of the USER ports on the AAM1 008. Step 2. Connect the other end of the telephone wire to th e upper ports of the MDF using a punch-down tool. Step 3. Co[...]

IES-1000 Hardware Installation Guide 4-8 Hardware Connections Figure 4-8 One MDF for End-user and CO Connections Please refer to the following figure for the connection schema.  MDF 1 is the original MDF used for telephone connections only.  MDF 2 is used for telephone connections only.  MDF 3 is for ADSL service connections. Change the wi[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-9 Figure 4-9 Installation Scenario B Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (MDFs 2 and 3). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008. Step 3. Connect the other ends of the telephone wi[...]

IES-1000 Hardware Installation Guide 4-10 Hardware Connections 4.4.4 Installation Scenario C Phone service is also available but there are two MDFs; one for end-user telephone lin e connections and the other one for CO telephone line connections (see the following figure). Users A and B have telephone (only) service. Figure 4-10 Two Separate MDFs f[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-1 1 Figure 4-11 Installation Scenario C Procedure T o Connect T o MDFs Step 1. Acquire two additional MDFs (3 and 4). Step 2. Connect the RJ-11 connector ends of telephone wires you want for ADSL service to the USER ports on the AAM1008. Step 3. Connect the other ends of the telephone wire[...]

IES-1000 Hardware Installation Guide 4-12 Hardware Connections Connect the top ports of MDF 1 to the telephone company. 4.4.5 LAN Port (Ethernet) Connection Connect the LAN port of your SAM1008 to an Ethernet WAN switch using a st raight-through Category 5 UTP (Unshielded Twisted Pair) cable with RJ -45 connectors. Connect the other end of the cabl[...]

IES-1000 Hardware Installation Guide Hardware Connections 4-13 Make sure you use a 100-240VAC/1A, 50/60Hz power source. Figure 4-13 Connecting the Power Cord to the IES-1000 and a Power Source[...]

[...]

IES-1000 Hardware Installation Guide T urning On Y our IES-1000 5-1 Chapter 5 Tu r n i n g On Y our IES-1000 This chapter discusses the fans and LEDs of the IES-1000 after you turn it on. 5.1 Introduction Before turning on your IES-1000, m ake sure you: • Have attached a computer to the IES-1000 serial port as explained previously. • Can see th[...]

IES-1000 Hardware Installation Guide 5-2 T urning On Y our IES-1000 5.2 Network Module Front Panel LEDs The following figures show the front panels of the network modules. LEDs describe the operational status of your network module. Please also refer to the Hardware Troubleshooting chapter to see how LEDs may aid in troubleshooting. Figure 5-2 SAM1[...]

IES-1000 Hardware Installation Guide Hardware T roubleshooting 6-1 This chapter explains how to troubleshoot IES-1000 hardware. Refer also to the Troubleshooting chapter in the User’s Guide . 6.1 System S t artup When you turn on the IES-1000, it automatically runs a self-test that takes approximately 20 seconds. The SYS LED will remain on if you[...]

IES-1000 Hardware Installation Guide 6-2 Hardware T roubleshooting 6.3 The SHDSL LED(s) Do Not T urn On The SHDSL LEDs show the operational status of SHDSL port co nnections. If the SHDSL LED is off, it means the link to the SHDSL modem/router is down or there is not a connection to the SHDSL po rt. Table 6-3 SHDSL LED Troubleshooting STEP CORRECTI[...]

IES-1000 Hardware Installation Guide Hardware T roubleshooting 6-3 Table 6-4 ADSL LED Troubleshooting STEP CORRECTIVE ACTION 9 If your line quality is low, you may need to select slower upstream and do wnstream line rates for both the IES-1000 and CPE sides. Refer to the User’ s Guide . 10 Repeat the steps above us ing a different ADSL port. 6.5 [...]

[...]

IES-1000 Hardware Installation Guide Appendix A Removing and Installing a Fuse A Appendix A Removing and Inst alling a Fuse This appendix shows you how to remove and install fuses fo r the IES-1000. The IES-1000 uses one 250V-3A fuse. The IES-1000 come s with two 250V-3A fuses; one is installed at the factory (in the fuse housing) and the other is [...]

IES-1000 Hardware Installation Guide B Appendix A Removing and Installing a Fuse Step 3. Using a small flat head screwdriver, gently pry open t he right side of the fuse housing (located t o the left of the power cord port receptacle) as shown next. Diagram 2 Opening the Fuse Housing Step 4. Gently pull the fuse casing from the IES-1000. The in sta[...]

IES-1000 Hardware Installation Guide Appendix A Removing and Installing a Fuse C Diagram 3 Locations of the Installed and Spare Fuses Step 5. Remove the burnt-out fuse from the IES-1000. A burnt-out fuse is blackened, darkened or cloudy inside its glass casing. A working fuse has a completely clear glass casing . Dispose of the burnt-out fuse. Inst[...]

IES-1000 Hardware Installation Guide D Appendix B PIN Assignments Appendix B Pin Assignment s Mini RJ-1 1 4P4C (Console Port) Pin Assignment s Diagram 4 RJ-11 4P4C (Console Port) Pin Assignments RJ-1 1 6P2C (SHDSL Port s on the SAM1008 and ADSL USER or CO Port s on the AAM1008) Pin Assignments Diagram 5 RJ-11 6P2C (SHDSL Port) Pin Assignments[...]

IES-1000 Hardware Installation Guide Appendix B PIN Assignments E Note that a 2, 4 or 6 pin connector can be used with this port provided pins 3 and 4 connect to a SAM1008 SHDSL port. RJ-45 (LAN Port) Pin Assignments Diagram 6 RJ-45 (LAN Port) Pin Assignments 1 = TX+ 8 = Not Connected 2 = TX- 7 = Not Connected 3 = RX+ 6 = RX- 4 = Not Connected 5= N[...]

IES-1000 Hardware Installation Guide F Appendix C Hardware S pecifications Appendix C Hardware S pecifications Physical Interfaces IES-1000 • Two slots for a total of up to two hot-swappable xDSL network modules • Power receptacle • 19” 1U rack-mountable, wall-mountable unit • Each network module has one mini RJ-11 console port for local [...]

IES-1000 Hardware Installation Guide Appendix C Hardware S pecifications G • One AAM1008 = 1.1 kg Power Consumption • 60 w atts max imu m • 100-240VAC/1A, 50/60Hz Fuse Rated • T3A 250VAC Operating Environment • Temperature: 0ºC — 50ºC • Humidity: 5% — 95% Storage Environment • Temperature: -25ºC — 70ºC • Humidity: 5% — 9[...]

[...]

IES-1000 Hardware Installation Guide Index I Index # #2 Philips screwdriver ............................. 2-1, 2-2, 2-3 1 10 Mbps Ethernet ................................................... 5-2 100 Mbps Ethernet ................................................. 5-2 A AAM1008 Connections ......................................... 4-5 AC INPUT ......[...]

IES-1000 Hardware Installation Guide J Index I IES-1000................................................................. viii Installing a Network Module .................................. 3-2 Installing Fuses ......................................................... C Integrated Ethernet Switch ........................................ ii L LED DSL[...]

IES-1000 Hardware Installation Guide Index K SYS LED................................................................ 6-1 T Telnet ..................................................................... 4-1 Temperature .............................................................. F Trademarks...........................................................[...]