Agilent Technologies E4443A(3HZ-6.7GHZ) manual

User ’ s and Programmer ’ s Reference Vo l u m e 2 One-Button Power Measurements PSA and ESA Series Spectrum Analyzers Refer to V olume 1 for core spectrum analyzer information. This manual provides documentation for the following instruments: Agilent T e chnologies PSA Series E4443A (3 Hz - 6.7 GHz ) E4445A (3 Hz - 13.2 G Hz) E4440A (3 Hz - 26[...]

2 Legal Information The informatio n contained in this docume nt is subject to change w ithout notice. Agilent T echnologies makes no warranty of any kind with regard to this ma terial, including but not limited to, the implied warranties of merc hantability and fitness for a part icular purpose. Agilent T echnologies shall not be liable for errors[...]

Contents 3 T able of Contents 1. Using This Docum ent About the User ’ s and Programmer ’ s Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 What is in This Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 T erms Us ed in This Bo ok . . . . [...]

4 Contents T able of Contents A vg Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 A vg Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 10 A verage T ype. . . . . . . . . . .[...]

Contents 5 T able of Contents Harmonics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 ST/Harmonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 42 Range T able (On/Off) . . . . . . . . . . . .[...]

6 Contents T able of Contents Display (Spectrum Emi ssions Mask—SEM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Full Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Limit Display . . . . . . . . . . . . . . . . . . . . . .[...]

Contents 7 T able of Contents CCDF (Power Stat) Measurement: Meas Setup Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 CCDF (Power Stat) Measurement: Displa y Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 CCDF (Power Stat) Measurement: Marker Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

8 Contents T able of Contents[...]

List of Commands 9 List of Commands :CALCulate:ACPower:O FFSet:LIST : LIMit:NEGative[:UPPer]:DA T A <rel_power> ,<rel_power> ,<rel_power> , <rel_power>,<rel_powe r>,<rel_power> . . . . . . . . . . . . . . . 95 :CALCulate:ACPow er:OFFSet:LIST :LIMit:NEGative[:UPPe r]:DA T A? . . . . . . . . . . . . . . . . . . . .[...]

10 List of Commands List of Commands ger> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 21 :CALCulate:SPURious[:RAN Ge][:LIST]:LIMit:ABSolute [:UPPER]:DA T A:STOP: AUTO OFF|ON|0|1, OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . .[...]

List of Commands 11 List of Commands :FETCh:HARMonics:F UNDamental? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 :FETCh:HARMonics[ :DIST ortion]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 :FETCh:HARMonics[ n]? . . . . . . . . . . .[...]

12 List of Commands List of Commands :MEASure:HARMonics: AMPLitude:ALL? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 :MEASure:HARMonics: AMPLitude[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 :MEASure:HARMonics: FREQuency:ALL? . . . . . . . . [...]

List of Commands 13 List of Commands :READ:HARMo nics[:DIST ortio n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 :READ:HARMo nics[n]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 :READ:MCP[n]? . . . . . . .[...]

14 List of Commands List of Commands [:SENSe]:ACPower: CORRection:NOISe[:AU TO]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 [:SENSe]:ACPower: FIL T e r[:RRC]:ALPHA <numb er> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 [:SENSe]:ACPower: FIL T er[:RRC][:ST A T e] OFF|ON|0|1 [...]

List of Commands 15 List of Commands [:SENSe]:BPO W er:THR eshold <number> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 [:SENSe]:BPOW er:THReshold:T YPE ABSolute|RELat ive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1 [:SENSe]:BPO W er:TH Reshold:TYPE? . . . . . . . . . [...]

16 List of Commands List of Commands [:SENSe]:HARMoni cs:RANGe[:LIST]:BWIDth|B ANDwidth[:RESol ution]:AUTO? . . . . . . . . . . . . 147 [:SENSe]:HARMonics:RA NGe[:LIST]:BWIDth|B ANDwidth[:RESol ution]<integer> . . . . . . . . . . 147 [:SENSe]:HARMoni cs:RANGe[:LIST]:BWID th|BANDwidth[:R ESolution]? . . . . . . . . . . . . . . . . . . 147 [:SE[...]

List of Commands 17 List of Commands [:SENSe]:MCPower:CARRier:LIST :BANDw idth|BWIDth[:INT egration]? . . . . . . . . . . . . . . . . . . 165 [:SENSe]:MCPower:CARRier:LIST :PPResent YES|NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 [:SENSe]:MCPower:CARRier:LIST :PPResent?. . . . . . . . . . . . . . . . . . . . . . . . . .[...]

18 List of Commands List of Commands [:SENSe]:OBW:MAXHold OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 [:SENSe]:OBW:MAXHold? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 [:SENSe]:OBW:XDB <dB value> . . . . . .[...]

List of Commands 19 List of Commands [:SENSe]:SEMask:A VERage:COUNt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 83 [:SENSe]:SEMask:A VERage[:ST A T e] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 [:SENSe]:SEMask:A VERage[:ST A T e]? . . . . . . . . . . [...]

20 List of Commands List of Commands [:SENSe]:SEMask:OF FSet[n]:LIST :ST ARt:ABS olute ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 [:SENSe]:SEMask:OF FSet[n]:LIST :S T ARt:RCARrier <re l_ ampl>, ... [<rel _am pl>] (up to five values) 198 [:SENSe]:SEMask:OFFSet[n]:LIST :ST ARt:RCAR rier? . . . . . . . . . [...]

List of Commands 21 List of Commands [:SENSe]:SPUR ious:A VERage[:ST A T e] OFF|ON|0|1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 [:SENSe]:SPUR ious:A VERage[:ST A T e]? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 [:SENSe]:SPUR ious:FSMeas OFF|ON|0|1 . . . . . . . . . [...]

22 List of Commands List of Commands [:SENSe]:SPURious[:R ANGe][:LIST]:P OINts[:FUNCtion] NORMal |A VERage|POSitive|SAM- Ple|NEGative|QP Eak|EA V erage|EPO Sitive|MPositive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 [:SENSe]:SPURio us[:RANGe][:LI ST]:POINts[ :FUNCtion] OFF|NORMal |A VERage|POSi- tive|SAMPle|NEGative|QPEak|E[...]

List of Commands 23 List of Commands NONE|IS95a|JSTD|IS95C|GSM|W3GPP|C2 000MC1|C2000DS|C2000MC3|NAD C|PDC| BLUEtooth|TETRa|WL802DOT1 1A|WL802DOT 1 1B|WL802DOT1 1G|HIPERLAN2|DVBTDLN DVBTGPN|DVB TIPN|FCC15|SDMBSE |UWBINDOOR| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33[...]

24 List of Commands List of Commands[...]

25 Using This Doc ument 1 Using This Document This book, V olume 2, provides the user and programming information for the one-button power measurement functions. For the core spectrum analyzer functionality refer to Vo l u m e 1 , Core Spectrum Analyzer Functions User ’ s and Programmer ’ s Reference .[...]

26 Chapter 1 Using This Document About the User’ s and Pr ogrammer’ s Information Using This Docu ment About the User ’ s and Programmer ’ s Information Y our user ’ s and programmer ’ s information is organized in two volum es, V olume 1, Core Spectrum Analyzer Functions User ’ s and Programmer ’ s Referenc e and V olume 2, One-But[...]

Chapter 1 27 Using This Document About the User’ s and Pr ogrammer’ s Information Using This Doc ument T erms Used in This Book There are many terms used throughout this b ook, for example “active function block,” that are explained in detail in the Getting Started guide. It is recommended that you read the Getting Started guide first. The [...]

28 Chapter 1 Using This Document About the User’ s and Pr ogrammer’ s Information Using This Docu ment[...]

29 One-Button Measurement Functions 2 One-Button Measurement Functions This chapter pro vides you with function al descriptions, and remote programming commands for all measuremen ts available to you when you press the front-panel Measure key (Spectrum Analysis mode is selected).[...]

30 Chapter 2 One-Button Measurement Functions One - Button Measurement Functions One-Button Measurement Functions One - Button Measurement Functions This section provides key descriptions and programming information for each key associated with the measurements avai lable when you press the front-panel Measure key . Note that the information for ke[...]

Chapter 2 31 One-Button Measurement Functions One - Button Measurement Functions One-Button Measurement Functions T race/V iew 173 Occupied BW Measurement Meas Setup 177 Spectrum Emission Mask Measur ement Meas Setup 183 T race/V iew 21 1 Display 205 Span X Scale 209 Marker 207 Spurious Emissions Measurement Meas Setup 213 Key Function Page Locatio[...]

32 Chapter 2 One-Button Measurement Functions One - Button Measurement Functions One-Button Measurement Functions[...]

Chapter 2 33 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1 Mode Setup (Spectrum Analysis Mode) Enables you to change measurement settings comm on to all measurements in the MEASURE menu. In Spectrum Analysis mode , there are several built-in power measurements. Parameters that you set in t[...]

34 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.1 None Selects no radio standard. If Radio Std, None is selected when a measurem ent is running, all measurement parameters are re turned to their default valu es. Analyzer parameters outside the MEASURE or Meas Setup key menus a[...]

Chapter 2 35 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions Key T ype: 1 of N menu Key Path: Mode Setup , Radio Std History: Modified with PS A firmware revision A.04.00 Added with PSA firmware revision A.02.00 Modified with ESA firmware revision A.08.00 Added with ESA firmware revision A.07.00[...]

36 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions Modified with ESA firmware revision A.08.00 Added with ESA firmware revision A.07.00 Remote Command: Use [:SENSe]: RADio:STANd ard[:SELec t] See “Radio Std” on page 33. Example: RAD:STAN G SM 2.1.1.6 3GPP W -CDMA Sets the specific [...]

Chapter 2 37 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Use [:SENSe]: RADio:STANd ard[:SELec t] See “Radio Std” on page 33. Example: RAD:STAN C2 000MC1 2.1.1.8 cdma2000 MC-3X Sets the specific parameters for the sel ected me asurem ent (located unde r th e “MEASURE (Sp[...]

38 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.10 NADC Sets the specific parameters for the sel ected me asurem ent (located unde r th e “MEASURE (Spectrum Analysis Mode)” ke y description) appropriate fo r industry standard NADC. Channel Power and Inte rmod TOI meas urem[...]

Chapter 2 39 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.12 Bluetooth™ Sets the specific parameters for the sel ected me asurem ent (located unde r th e “MEASURE (Spectrum Analysis Mode)” key description) appropriat e for industry standard Bluetooth™. Power Stat CCDF and Burst [...]

40 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.13 TETRA Sets the specific parameters for the sel ected me asurem ent (located unde r th e “MEASURE (Spectrum Analysis Mode)” ke y description) appropriate fo r industry standard TETRA. This standard is only available for the[...]

Chapter 2 41 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions History: Modified with PS A firmware revision A.04.00 Added with PSA firmware revision A.03.00 Added with ESA firmware revision A.09.00 Remote Command: Use [:SENSe]: RADio:STANd ard[:SELec t] See “Radio Std” on page 33. Example: RA[...]

42 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Use [:SENSe]: RADio:STANd ard[:SELec t] See “Radio Std” on page 33. Example: RAD:STAN WL 802DOT11 B 2.1.1.15.3 802.1 1g Sets the specific parameters for the selected measurement (located under the “MEASURE (Spectr[...]

Chapter 2 43 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions television system. This standard is only available for the ch annel power and CCDF measurements Key Path: Mode Setup , DV B - T History: Added with PSA firmware revision A.04.00 Added with ESA firmware revision A.10.00 Remote Command: [...]

44 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.16.2 G/P AL/NICAM Pressing G/P AL/NICAM selects the filtering masks for the G/P AL/NICAM analog telev ision system. This standard is only available for the channel power and CCDF measurements. NO TE The ESA series a nalyzers requ[...]

Chapter 2 45 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.1.17.1 System E PSA Only: Se ts the specific parameters for t he selected measurement (located under the “MEASURE (Spe ctrum Analysis Mode)” key description) appropriate for industry standard System E. This standard is only ava[...]

46 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.2 Radio Std Setup Accesses the key menu for selecti ng the device, packet type, or sign al bandwidth to be measured. Key Path: Mode Setup History: Modified with PS A firmware revision A.04.00 Added with PSA firmware revision A.02.0[...]

Chapter 2 47 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.2.2 Device BTS/MS This function is only available when you ha ve selected the standard: IS-95, J -STD-008, cdma2000, W -CDMA, NADC, PDC, TETRA, or GS M. It enables you to select either the base transmitter station (BTS) setu p de f[...]

48 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions to select the band class. Key Path: Mode Setup, Std Setup Factory Preset: US/K or Cell History: Modified with PS A firmware revision A.04.00 Added with PSA firmware revision A.02.00 Modified with ESA firmware revision A.08.00 Added wit[...]

Chapter 2 49 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions 2.1.4 Enable All Measurements Allows you to access me asurem ents that are disabled. Not all measurements are available for a particular radio standard. When you sele ct a radio standard, the keys are grayed out for the measurements th[...]

50 Chapter 2 One-Button Measurement Functions Mode Setup (Spectrum Analysis Mode) One-Button Measurement Functions[...]

Chapter 2 51 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2 MEASURE (Spectrum Analysis Mode) In the Spectrum Analysis mode (see the Mode key), this key displays a menu that lets you to make transmitter power me asurements such as adjacent channel power , occupied bandwidth, and harmonic distor[...]

52 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Command Interactions: MEASure, CONFigure, FETCh, INIT iate and READ Figure 1 Measurement Group of Commands[...]

Chapter 2 53 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Measure Commands: :MEASure:< measurement >[n]? This is a fast single-command way to ma ke a measurement using the factory default instrument settings. These are the settings and units that conform to the Mode Setup settings (e.g. ra[...]

54 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Configure Commands: :CONFigure:<measur ement> This command stops the current measurement (i f any) and sets up th e instrumen t for the specified measurement using the factory default in strument settings. It sets the instrument to [...]

Chapter 2 55 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions READ Commands: :READ:<measurement>[n]? • Does not preset the measurement to the factor y default settings. For example, if you have previously initiated the ACP measurement and you send READ:ACP? it will initiate a new measurement[...]

56 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.1 Current Measurement Query (Remote Command Only) This command returns the name of the measurement that is currently running. Remote Command: :CONFigure? Example: CONF? 2.2.2 T est Current Results Agains t all Limits (Remote Command O[...]

Chapter 2 57 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.3 Meas Off This key accesses th e core spectrum analysis measureme nt functionality . It turns off the current one-button measurement s o there are no keys availab le in the Meas Setup menu. See the spectrum analysis measurement featu[...]

58 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Figure 2-1 ESA Channel Power Measurement Results Figure 2-2 PSA Channel Power Measurement Results NOTE The displayed trace is the current trace, not the averaged trace. Pressing Meas Setup after Channel Power has been selected will access[...]

Chapter 2 59 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions When a DVB-T radio standard i s selected, this measurement will also compare the input signal against a pre-defined spectrum mask. The mask amplitudes defined in the DVB-T specification (ETSI EN 300 744 V1.4.1) range f rom 0 dB to 100 dB.[...]

60 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Example: FETC:CHP? or MEAS:CHP? or READ:CHP? command returns scalar results of main channel power and power density . FETC:CHP:CHP ? or MEAS:CHP:DENS? or READ:CHP:DENS? commands will return the single scalar result specified.[...]

Chapter 2 61 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.5 Occupied BW Occupied Bandwidth integrates the power of the displayed spectrum and puts markers at the frequencies between which a selected percentage of the power is contained. The measurement defaults to 99% of the occupi ed bandwi[...]

62 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Example: FETC:OBW? or MEAS:OBW? or READ:OBW? command returns scalar results of occupied bandwidth and tran smit frequency error . FETC:OBW:FERR? or MEAS:OBW :FERR? or READ:OBW :FERR? commands will return the single scalar result specified[...]

Chapter 2 63 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions improved speed of maki ng ACP measurements. Fast is only enabled for the 3GPP W -CDMA radi o standard only . The measurement settings may be co nfigured by pressing Meas Setup after ACP has been selected. Pressing Radio S tandard after Mo[...]

64 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Measurement Results A vailable Condition Command Results Returned :CONFigure: ACPower :INIT iate:ACPower Not Applica bl e Radio Std = None and only offset A is on :FETCh:ACPower[n]? :MEASure:ACPower[n]? :READ:ACPower[n ]? [...]

Chapter 2 65 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Radio Std ≠ None or Radio Std = None and more than one offset is on Meas T ype = T otal Pwr Ref Returns 28 values that correspond in the following order: 1. Main Channel- relative power spec tral density (dB) 2. Main Channel- p ower spe[...]

66 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command Notes: The main channel power is returned in the current amplitude units, and the lower and upper channel results are always returned in dB. Example: FETC:ACP? or MEAS:ACP? or READ:ACP? commands return the scalar results of[...]

Chapter 2 67 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.7 Multi-Carrier Power Multi-Carrier Power is the measure of the power that leaks into adjacent transmit channels when two or more carriers are present. The re sults reported are identical to th e adjacent power measurement, but th e s[...]

68 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Measurement Results A vailable Command n Results Returned :CONFigure :MCP ower N/A Not Applicable :FETCh:MCP[ n]? :MEASure:MCP[n]? :READ:MCP[n ]? n=1 (or not specified) Returns 20 comma-separated scalar results, in the fol[...]

Chapter 2 69 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Example: FETC:MCP? or MEA:MCP? or READ:MCP? :FETCh:MCPo wer? :MEASure:MC Power? :READ:MCPow er? n=14 Returns 36 comma-separated scalar results, in the following orde r . 1 to 24. All carriers absol ute and relative values 25. lower offset[...]

70 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.8 Power Stat CCDF The CCDF measurement is a statistical measurement of a high-level signal or peak power . It shows in both graphical and tabular form for what percentage of the tim e a signal exceeds its average power , and by how mu[...]

Chapter 2 71 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Figure 2-4 Power Stat CCDF Measurement Results Pressing Meas Setup after Power S tat CCDF has been selected will access the Power Stat CCDF measurement setup menu. The factory defa ults provide a good starting point for this measurement. [...]

72 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Measurement Results A vailable Command n Results Returned :CONFigure:PST atistic :INIT iate:PST atistic N/A Not Applicable :FETCh:PST atistic[n]? :MEASure:PST atistic[n]? :READ:PST at istic[n]? n=1 (or not specified) Retur[...]

Chapter 2 73 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command Notes: T o save trac e data use the fetch methods shown above. Example: FETC:PST? or MEAS:PST? or READ:PST? FETC:PST2? or MEAS:PST2? or READ:PST2? FETC:PST3? or MEAS:PST3? or READ:PST3? 2.2.9 Harmonic Distortion The range t[...]

74 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions the measurement is in continuous mode, th e measurement will cont inually measure the amplitude of the fundamen tal and harmonics. For averaged measurement s, you may specify the number o f sweeps over which t he amplitude of each ha rmon[...]

Chapter 2 75 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Example: FETC:HARM:AMPL:ALL? MEAS:HARM:AMPL2? returns the amplitude of the sec ond harmonic measured in dBc from the fundamental. READ:HARM:FREQ10 returns the frequency of the tenth harmonic in Hz. :FETCh:HARM onics:FREQuenc y:ALL? :MEASu[...]

76 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.10 Burst Power The burst power measurement is an accurate method of determining th e average power for the specified burst. Burst power measures th e average power in ze ro-span mode for the captured burst. This measurement is prim ar[...]

Chapter 2 77 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions where Pavg = average power , n is the start trac e point, m= the stop trace point, and p= the trace point amplit ude power in dBm. Figure 2-5 shows an example of the results obtained when measuring a Bl uetooth™ signal and with a user-d[...]

78 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions key). Other measurements are availabl e in other modes if an op tional personality is installed. Key Path: MEASURE Remote Command: Example: FETC:BPOW? or MEAS:BPOW? or READ:BPOW? Measurement Results A vailable Command n Results Returned :[...]

Chapter 2 79 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.1 1 Intermod (TOI) The third order intermodulation (TOI) me asurement computes and displays the output intercept point (IP3), and places markers upon the trace to indicate the measured signals and third-order products. For more inform[...]

80 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.12 Spurious Emissions The spurious emissions m easurement identifies a nd determines the power level of spurious emissions in ce rtain frequency bands. Fo r more information see “Meas Setup (Spurious Emissi ons)” on page 213 . Key[...]

Chapter 2 81 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions 2.2.13 Spectrum Emission Mask Spectrum Emission Mask meas urement includes the in-band and o ut-of-band spurious emissions. As it applies to W -CDMA (3GPP), this is the power contained in a specified frequency bandwidth at certain offsets[...]

82 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Remote Command: Measurement Results A vailable Command / Condition n Results Returned :CONFigure:SEMask :INIT iate:SEMask N/A Not Applicable :FETCh:SEMask[n]? :MEASure:SEMask[n]? :READ:SEMask[n]? Using T otal Power Reference n=1 (or not s[...]

Chapter 2 83 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Using Power Spectral Density Reference (Continu ed) n=1 (or not specified) Returns 60 comma-separated scalar results, in the following order (70 when offset F is active): 1. Reserved for the futu re use, returns –999.0 2. Absolute power[...]

84 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions n=2 Returns the displaye d freq u enc y dom ai n sp ectrum trac e da ta separated by comma. The number of data points is determined by the setting of the trace points parameter . n=3 Returns the displa ye d freq u en cy dom ain absolute l[...]

Chapter 2 85 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Using T otal Power Reference n=6 T otal Power Reference Returns 12 comma-separated scalar values (in dBc) of the power relative to the carrier at the segment frequencies (14 when offset F is active): 1. Reserved for the futu re use, retur[...]

86 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions n=8 Returns 12 comma-separated sc alar values of the pass/fail (0 = passed, or 1 = failed) results de termined by test ing the relative power in each offset against the specified offset’ s relative power limits (14 wh en offset F is a c[...]

Chapter 2 87 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions Example: FETC:SEM? or MEAS:SEM? or READ:SEM? n=1 1 Returns 12 comma-separated scal ar values (in dBc) of the peak power relative to the carrier at the segment frequencies (14 when offset F is active): 1. Reserved for the futu re use, retu[...]

88 Chapter 2 One-Button Measurement Functions MEASURE (Spectrum Analysis Mode) One-Button Measurement Functions[...]

Chapter 2 89 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions 2.3 Meas Setup (Adjacent Channel Power—ACP) If the adjacent channel power (ACP) me asurement has been selected in the Measure menu of the spectrum analysis mode, this key displays the ACP measurement setup menu. The adjacent [...]

90 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions 2.3.2 A vg Mode Press A vg Mode to select the type of termination cont rol used for the averaging function as either Exp or Repeat . This determin es the averag ing ac tion after the specified number of measurements (ave rage [...]

Chapter 2 91 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions Increment: RBW if CF Step i s set to Aut o with zero span. Span/10 if CF Step is set to Au t o with non-zero span. CF Step if CF Step is set to Manual . Range: 300 Hz to 500 MHz. Depends on the adjacent-channel settings and the[...]

92 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions MC-3X , and cdma2000 DS is sele cted. Key Path: Meas Setup , Offset Set up State Saved: Saved in instrument state. Factory Preset: The following table shows the de fault array if no radio standard ( None ) is selected. Default[...]

Chapter 2 93 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions values of these parameters if no radio standard ( None ) is selected. Example: Sending fewer th an six parameters to one of these com mands will leave the values of the unspecifi ed offsets unchanged. If you don’t se nd setti[...]

94 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions Default T erminator: Hz Range: PSA Only: 300 Hz to 500 MHz History: Added with PSA firmware revision A.02.00. Added with ESA firmware revision A.07.00. Remote Command: [:SENSe]:A CPower:OFFS et:LIST:BA NDwidth|BWI Dth[:INTegr [...]

Chapter 2 95 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions Key Path: Meas Setup , Offset Set up State Saved: Saved in instrument state. Factory Preset: 0.00 dB Default T erminator: dB Range: –200 dB to 200 dB History: Added with PSA firmware revision A.02.00. Added with ESA firmware [...]

96 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions 2.3.5 Meas T ype Press Meas T ype to specify the reference for the measurement, either To t a l P w r R e f or PSD Ref . Relative values can be di splayed re ferenced to either the total power ( To t a l P w r R e f ) or the p[...]

Chapter 2 97 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions 2.3.7 Method Enables you to set th e measurement method.The resol ution bandwidth method is most useful for measuring cdmaOn e and cdma2000 si gnals; the integration bandwidth method is preferred for other signals. NO TE ESA On[...]

98 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions 2.3.7.2 RBW PSA Only: Sets the measurem ent contr ol meth o d to RBW . Key T ype: 1 of N menu Key Path: Meas Setup , Method History: Modified with PS A firmware revision A.06.00 Remote Command: Use[:SENSe ]:ACPower:M ETHod See[...]

Chapter 2 99 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions 2.3.7.3 Fast PSA Only: Sets the measurement c ontrol method to Fast . When Fas t method is selected, the 5 point ACLR measurement method is used. The follo wing paramete rs are configured to allow the measurement to be made. Th[...]

100 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions Key T ype: 1 of N menu Key Path: Meas Setup , Method History: Added with PSA firmware revision A.06.00 Remote Command: Use[:SENSe ]:ACPower:M ETHod See “Me thod” on page 97. Example: ACP:METH FAST The following is an exam[...]

Chapter 2 101 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions State Saved: Saved in instrument state. Factory Preset: Auto, Meas ured carrier power value Te r m i n a t o r s : d B m Default T erminator: dBm Range: –200 dBm to 200 dBm History: Added with PSA firmware revision A.02.00. [...]

102 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions Remote Command: [:SENSe]:A CPower:CARR ier:CPSD < dBm> [:SENSe]:A CPower:CARR ier:CPSD? Remote Command Notes: This function is on ly available when measurement type is set to PSD Ref, use the command [:SENSe]:ACPower:TY[...]

Chapter 2 103 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP) One-Button Measurement Functions Alpha . The filter is unavailable when the measurement met h od is set to RBW . Key Path: Meas Setup State Saved: Saved in instrument state. Factory Preset: Off History: Added with PSA firmware revision A.03.00. Added with ESA[...]

104 Chapter 2 One-Button Measurement Functions Meas Setup (Adjacent Channel P ower—A CP ) One-Button Measurement Functions 2.3.13 Noise Correction Pressing Noise Correction turns noise correction on or off . When you set Noise Corr to On , a calibration of the noise fl oor is performed an d used to correct for analyzer noise floor contribution to[...]

Chapter 2 105 One-Button Measurement Functions T race/View (A CP Measurement) One-Button Measurement Functions 2.4 T race/V iew (ACP Measurement) If AC P has been selected in the Measure menu of the Spectrum Analysis mode, this key displays the app ropriate T rac e/View menu for the adjacent channel power (ACP) measurement. Displays menu keys that [...]

106 Chapter 2 One-Button Measurement Functions T race/View (A CP Measurement) One-Button Measurement Functions Remote Command: There is no remote co mm and for this function. 2.4.3 Combined Pressing Combined selects the measurement to be disp layed as a bar graph and spectrum as shown below . Key Path: T race/View Factory Preset: Spectrum History: [...]

Chapter 2 107 One-Button Measurement Functions T race/View (A CP Measurement) One-Button Measurement Functions Remote Command: There is no remote comm and for this function. 2.4.5 T race One-button measurements do n ot change this function. See V olume 1, Core Spectrum Analyzer Functions User ’ s and Programmer ’ s Reference guide for informati[...]

108 Chapter 2 One-Button Measurement Functions T race/View (A CP Measurement) One-Button Measurement Functions[...]

Chapter 2 109 One-Button Measurement Functions Meas Setup (Burst P o wer) One-Button Measurement Functions 2.5 Meas Setup (Burst Power) When Burst P ower has been selected in the Measure menu of the Spectru m Analysis Mode, this key displays the appro priate measurement setup menu. The burst power measurement is an accurate method of determin ing t[...]

110 Chapter 2 One-Button Measurement Functions Meas Setup (Burst P ower) One-Button Measurement Functions [:SENSe]:B POWer:AVERa ge:COUNt? [:SENSe]:B POWer:AVERa ge[:STATe] OFF|ON|0|1 [:SENSe]:B POWer:AVERa ge[:STATe] ? Example: BPOW:AVER: COUN 100 BPOW:AVER ON 2.5.2 Av g M o d e Press A vg Mode to select the type of termination cont rol used for t[...]

Chapter 2 111 One-Button Measurement Functions Meas Setup (Burst P o wer) One-Button Measurement Functions points. • RMS — Selects averaging that converts trac e data from dB to power units, then averages the power trace data. This sele ction requires more time to perform. Key Path: Meas Setup Factory Preset: RMS Range: RMS or Log History: Adde[...]

112 Chapter 2 One-Button Measurement Functions Meas Setup (Burst P ower) One-Button Measurement Functions [:SENSe]:B POWer:THRes hold:TYPE? Example: SENS:BPOW: THR:TYPE AB S 2.5.5 Meas Method Allows you to select th e m easurement method. • Above T hreshold Lvl — Selects the user defined threshol d level or default level (-3.00 dB) as the crite[...]

Chapter 2 113 One-Button Measurement Functions Meas Setup (Burst P o wer) One-Button Measurement Functions width. In either case, the burst width is centered o n the observed burst in each measurement. NO TE This key wil l be grayed out if Meas Method is set to Abo ve Threshold Lvl . Key Path: Meas Setup Factory Preset: 542.77 µ s T erminators: %,[...]

114 Chapter 2 One-Button Measurement Functions Meas Setup (Burst P ower) One-Button Measurement Functions State Saved: Saved in instrument state. Factory Preset: n/a History: Added with PSA firmware revision A.02.00. Added with ESA firmware revision A.07.00 Remote Command: [:SENSe]:P OWer[:RF]:R ANGe:AUTO ON CE Example: POW:RANG:A UTO ONCE[...]

Chapter 2 115 One-Button Measurement Functions T race/View (Burst P o wer) One-Button Measurement Functions 2.6 T race/V iew (Burst Power) If Burst P ower has been selected in the Measure men u of the Spectrum Analysis mode, this key displays the appropriate T race/View menu for the burst power measurement. Displays menu keys that enable you to set[...]

116 Chapter 2 One-Button Measurement Functions T race/View (Burst P o wer) One-Button Measurement Functions output power is displayed at the bottom of the bar . Refer to the following figure. Key Path: T race/View History: Added with PSA firmware revision A.02.00 Added with ESA firmware revision A.08.00 2.6.3 T race One-button measurements do n ot [...]

Chapter 2 117 One-Button Measurement Functions Meas Setup (Complementary Cumula tive Distribution Function—CCDF) One-Button Measurement Functions 2.7 Meas Setup (Complementary Cumulative Di stribution Function—CCDF) When P ower Stat CCDF has been selected in the Measu re menu of the Spectrum Analysis mode, this key displays the appropriate me a[...]

118 Chapter 2 One-Button Measurement Functions Meas Setup (Complementary Cumula tive Distrib ution Function—CCDF) One-Button Measurement Functions Remote Command Notes: The entered value is rounded to the nearest Res BW filter frequency . This command is coupled with the analyzer resolution bandwidth Example: PST:BA ND 10 or PST:BWI D 10 PST:BAND[...]

Chapter 2 119 One-Button Measurement Functions Meas Setup (Complementary Cumula tive Distribution Function—CCDF) One-Button Measurement Functions ESA Only: 1 µ s minimum. Maximum value depends upon the measurement bandwidth. BW factor = 5 x mea s BW or 10,000,000; whichever is less. History: Added with PSA firmware revision A.02.00 Added with ES[...]

120 Chapter 2 One-Button Measurement Functions Meas Setup (Complementary Cumula tive Distrib ution Function—CCDF) One-Button Measurement Functions[...]

Chapter 2 121 One-Button Measurement Functions Display (Complementary Cumulati ve Distribution Function—C CDF) One-Button Measurement Functions 2.8 Display (Complementary Cumulative Distribution Function—CCDF) Press Displa y to access menu keys that allow you to co nfigure parameters fo r the CCDF measurement. NO TE The keys described below are[...]

122 Chapter 2 One-Button Measurement Functions Display (Complementary Cumulati ve Distribution Function—CCDF) One-Button Measurement Functions 2.8.3 Ref T race Press Ref T race to toggle the reference trace display function between On and Off . Key Path: Display State Saved: Saved in instrument state. Factory Preset: Off Remote Command: :DISPlay:[...]

Chapter 2 123 One-Button Measurement Functions Display (Complementary Cumulati ve Distribution Function—C CDF) One-Button Measurement Functions 2.8.5.1 Graticule Pressing Graticule turns the display graticules On or Off . Key Path: Display , Preferences Factory Preset: On Factory Default: On Te r m i n a t o r s : E n t e r History: Added with PS[...]

124 Chapter 2 One-Button Measurement Functions Display (Complementary Cumulati ve Distribution Function—CCDF) One-Button Measurement Functions[...]

Chapter 2 125 One-Button Measurement Functions Marker (Complementary Cumulati ve Distribution Function—CCDF) One-Button Measurement Functions 2.9 Marker (Complementary Cu mulative Distribution Function—CCDF) Displays the Mar ker control m enu for the CCD F measurement. All markers are off until either Normal or Delta is pressed. There are three[...]

126 Chapter 2 One-Button Measurement Functions Marker (Complementary Cumulati ve Distrib ution Function—CCDF) One-Button Measurement Functions State Saved: The number of the selected marker is saved in instrument state. Factory Preset: Marker 1 History: Added with ESA firmware revision A.07.00 Remote Command: :CALCulate :PSTatistic :MARKer[1] |2|[...]

Chapter 2 127 One-Button Measurement Functions Marker (Complementary Cumulati ve Distribution Function—CCDF) One-Button Measurement Functions History: Added with ESA firmware revision A.07.00 Remote Command: See V olume 1, Core Spectrum Analyzer Functions User ’ s and Programmer ’ s Reference guide. Example: CALC:PST:M ARK3:MODE D ELT selects[...]

128 Chapter 2 One-Button Measurement Functions Marker (Complementary Cumulati ve Distrib ution Function—CCDF) One-Button Measurement Functions Example: CALC:PST:M ARK1:TRAC G AUSsian places marker 1 on the Gauss ian trace. 2.9.6 Marker All Off T urns off all markers. NO TE Selecting any measuremen t (including Meas Off ) under Measure , turns off[...]

Chapter 2 129 One-Button Measurement Functions Marker (Complementary Cumulati ve Distribution Function—CCDF) One-Button Measurement Functions :CALCulate :PSTatistic :MARKer[1] |2|3|4:X:PO Sition? This defines marker X position in display points from 0 to 50 dB. Example: CALC:PST:M ARK:X 30 dB activates a normal marker (m arker 1) at the 30 dB loc[...]

130 Chapter 2 One-Button Measurement Functions Marker (Complementary Cumulati ve Distrib ution Function—CCDF) One-Button Measurement Functions[...]

Chapter 2 131 One-Button Measurement Functions SP AN X Scale (Complementary Cumu lative Distribution Funct ion—CCDF) One-Button Measurement Functions 2.10 SP AN X Scale (Compl ementary Cumulative Distribution Function—CCDF) Activates the Span function for the CCDF measurement and displays the menu of span functions. Key Path: Front-panel key St[...]

132 Chapter 2 One-Button Measurement Functions SP AN X Scale (Complementary Cumu lative Distribution Function— CCDF) One-Button Measurement Functions[...]

Chapter 2 133 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions 2.1 1 Meas Setup (Channel Power—CHP) When the channel power me asurement has been selected in th e Measure key menu of the Spectrum Analysis Mode, this key displays the appropriate measurement setup menu. The Channel Power measurement[...]

134 Chapter 2 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions Example: CHP:AVER:C OUN 10 CHP:AVER:C OUN? CHP:AVER O FF CHP:AVER? 2.1 1.2 A vg Mode Press A vg Mode to select the type of termination cont rol used for the averaging function to either Exp or Repeat . This determin es the averag ing ac[...]

Chapter 2 135 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions Factory Preset: 2 MHz, or as defi ned by the selected radio standard. T erminators: GHz, MHz, kHz, Hz Default T erminator: Hz Knob Increment: 1% Step Key Increment: 1 ,1.5, 2, 3, 5, 7.5, 10... Range: 100 Hz to maximum span supported by [...]

136 Chapter 2 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions 2.1 1.5 Optimize Re f Level Sets the input attenuator and reference level to optimize the robustness of the measurement, which is its freedom from e rrors due to input compression and log amp range limita tions. NO TE There will always [...]

Chapter 2 137 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions available when either 3GPP W -CDMA or TETRA has been selected as the Ra dio Std. from the Mode Setup menu. Key Path: Meas Setup State Saved: Saved in instrument state. Factory Preset: 0.22 when W -CDMA is se lected, 0.35 for TETR A, oth[...]

138 Chapter 2 One-Button Measurement Functions Meas Setup (Channel P ower—CHP) One-Button Measurement Functions[...]

Chapter 2 139 One-Button Measurement Functions T race/View (Channel P ower Measurement) One-Button Measurement Functions 2.12 T race/V iew (Chann el Power Measurement) If Channel P o wer has been selected in the Measure menu of the Spectrum An alysis mode, this key displays the appropriate T race/Vie w menu for the channel power measurement. Displa[...]

140 Chapter 2 One-Button Measurement Functions T race/View (Channel P ower Measurement) One-Button Measurement Functions 2.12.1 Spectrum Pressing Spectrum selects the spectral display of the measurement. Key Path: T race/View Factory Preset: Spectrum History: Added with PSA firmware revision A.02.00 Remote Command: There is no remote co mm and for [...]

Chapter 2 141 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions 2.13 Meas Setup (Harmonic Distortion) When the harmonic distortion measure ment has been selected in the Measure key menu of the Spectrum Analysis Mode, this key displ ays the appropriate me asurement setup menu. Key Path: Front-Panel ke[...]

142 Chapter 2 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions combined with the existing av erage. Expo nential averaging weights new data more than old data, which facilitates tracking of slow-changing signals. The average will be displayed at the end of each sweep. • Repeat —When you set A vg[...]

Chapter 2 143 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions measurement was started is used for finding the fundamental. Key Path: Meas Setup State Saved: Saved in instrument state. Factory Preset: 10 ms / Auto Default T erminator: seconds Range: 10 ms to maximum sweep time of the analyzer Remote[...]

144 Chapter 2 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions 2.13.6 Range T able Enables you to enter the settings for up to 10 ranges, either using the instrument front panel keys or remotely . Upon entering the range table, the measurement stops, then the analyzer is set to a constantly sweeping[...]

Chapter 2 145 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions History: Added with PSA firmware revision A.03.00 Added with ESA firmware revision A.09.00 Remote Command: There is no equivalent remote command. 2.13.6.1 Range Selects a range and updates the values on the other Range T able keys so tha[...]

146 Chapter 2 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions Example: HARM:RANG:LIST:STAT ON,OFF,ON,ON 2.13.6.2 Center Freq Used to set the center frequency of the analyzer . Key Path: Meas Setup , Range T able Factory Preset: See T able 2-1 on page 145 . Knob Increment: 1% Step Key Increment: 1, [...]

Chapter 2 147 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions Remote Command: This parameter can send up to 10 values. The lo cati on in the list se nt corresponds to the range the value is associated with. Missing va lues are not permitted, for example, if you want to change values 2 and 6, you mu[...]

148 Chapter 2 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions analyzer determines the optimum set ting, while Man enables you to determine the setting. Key Path: Meas Setup , Range T able Factory Preset: Auto Knob Increment: Steps through the available video ba ndwidth filters. Step Key Increment: [...]

Chapter 2 149 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions Remote Command: This parameter can send up to 10 values. The lo cati on in the list se nt corresponds to the range the value is associated with. Missing va lues are not permitted, for example, if you want to change values 2 and 6, you mu[...]

150 Chapter 2 One-Button Measurement Functions Meas Setup (Harmonic Distortion) One-Button Measurement Functions NO TE There will always be a minimum of 2 dB for PSA or 5 dB for ESA of attenuation set to reduce the potential errors due to VSWR. Key Path: Meas Setup State Saved: Saved in instrument state. History: Added with PSA firmware revision A.[...]

Chapter 2 151 One-Button Measurement Functions T race/View (Harmonic Distor tion) One-Button Measurement Functions 2.14 T race/V iew (Harmonic Distortion) If Harmonic Distortion has been selected in the Measure menu of the Spectrum Analysis mode, this key displays the appropriate T race/View menu to view the harmonic measurement results. Displays m[...]

152 Chapter 2 One-Button Measurement Functions T race/View (Harmonic Distortion) One-Button Measurement Functions[...]

Chapter 2 153 One-Button Measurement Functions Meas Setup (Intermod (T OI)) One-Button Measurement Functions 2.15 Meas Setup (Intermod (TOI)) When Intermod (T OI) measurement has b een selected in the Mea sure menu of the Spectrum Analysis Mode, this key dis plays the approp riate measurement setup menu for third or der intercept (TO I). The TOI me[...]

154 Chapter 2 One-Button Measurement Functions Meas Setup (Intermod (T OI)) One-Button Measurement Functions [:SENSe]:T OIN:AVERage [:STATe]? Example: TOIN:A VER ON TOIN:AVER? 2.15.2 A vg Mode Press A vg Mode to select the type of termination cont rol used for the averaging function to either Exp or Repeat . This determin es the averag ing ac tion [...]

Chapter 2 155 One-Button Measurement Functions Meas Setup (Intermod (T OI)) One-Button Measurement Functions Range: Non-Zero Span of Analyzer History: Added with PSA firmware revision A.02.00 Added with ESA firmware revision A.08.00 Remote Command: [:SENSe]:T OIN:FREQuen cy:SPAN <num ber> [:SENSe]:T OIN:FREQuen cy:SPAN? Example: TOIN:F REQ:SP[...]

156 Chapter 2 One-Button Measurement Functions Meas Setup (Intermod (T OI)) One-Button Measurement Functions TOIN:FREQ: MIX:RANG:AU TO 1 TOIN:FREQ: MIX:RANG:AU TO? 2.15.5 Optimize Ref Level Sets the reference level to place the tones near the top of the display . When input attenuation is set to Au t o , pre ssing Opt imize Ref Level sets the inp u[...]

Chapter 2 157 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions 2.16 Meas Setup (Multi-Carrier Power—MCP) If the MCP measurement has b een selected in the Measure menu of the Spectrum Analysis mode, this key displays the MCP measurement setup menu. The Multi-Carrier Power measurement is a me[...]

158 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions [:SENSe]:M CPower:AVER age[:STATe ]? Example: MCP:AVER:C OUN 10 MCP:AVER:C OUN? MCP:AVER O FF MCP:AVER? 2.16.2 A vg Mode Press A vg Mode to select the type of termination cont rol used for the averaging function as either Exp or R[...]

Chapter 2 159 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Added with PSA firmware revision A.03.00. Remote Command: There is no equivalent remote command. 2.16.3.1 Carriers Press Carriers to specify the number of carriers to be measured. Key Path: Meas Setup , Carrier Setup Factory Prese[...]

160 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions History: Added with ESA firmware revision A.09.00. Added with PSA firmware revision A.03.00. Remote Command: [:SENSe]:M CPower:RCAR rier:AUTO OF F|ON|0|1 [:SENSe]:M CPower:RCAR rier:AUTO? [:SENSe]:M CPower:RCAR rier<integ er>[...]

Chapter 2 161 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions carrier power present values. State Saved: Saved in instrument state. Factory Preset: Auto/Calculate d based on current center freq uency . Refer to the algorithm above when defining the Ref Carrier Freq (Auto) key . T erminators:[...]

162 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Key Path: Meas Setup , Carrier Setup , Configur e Carrier s Dependencies/ Couplings: All keys ava ilable on the Configure Carrier key men u are coupled to this key . State Saved: Saved in instrument state. Factory Preset: 1 Knob I[...]

Chapter 2 163 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions [:SENSe]:M CPower:CARR ier:LIST:P PResent? Remote Command Notes: • The position number in the list sent corresponds to the carrier number you are designating. For example: “YES, YES, NO, YES, YES, NO” defines six carriers. C[...]

164 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions [:SENSe]:M CPower:CARR ier:LIST:W IDTh? Remote Command Notes: • The position nu mber of the each carrier width i n the list sent corresponds to the ca rrier number yo u are defining. For example : “5 MHz, 10 MHz, 5 MHz” defi[...]

Chapter 2 165 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Remote Command: [:SENSe]:M CPower:CARR ier:LIST:B ANDwidth|BW IDth[:INTeg ration]<Hz> [:SENSe]:M CPower:CARR ier:LIST:B ANDwidth|BW IDth[:INTeg ration]? Example: MCP:CA RR:LIST:BA ND 3.5MHz,2 .85MHz,3.84 MHz 2.16.4 Offsets/L[...]

166 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Factory Preset: 5 MHz, 10 MHz, 15 MHz T erminators: Hz, kHz, MHz, GHz Default T erminator: Hz Range: 0 MHz to 45 MHz History: Added with PSA firmware revision A.02.00 Added with ESA firmware revision A.09.00 Remote Command: [:SENS[...]

Chapter 2 167 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Example: MCP:OFFS:L IST:BWIDth 5M Hz,3MHz,5MH z MCP:OFFS:L IST:BWID? 2.16.4.4 Upper Offset Limit Sets the limit for the selected offs et (refer to “Offset” above) to the right of the carriers. Key Path: Meas Setup , Offset/Lim[...]

168 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Added with ESA firmware revision A.08.00 Remote Command: :CALCulate :MCPower:OF FSet:LIST: LIMit:NEGat ive[:UPPer] :DATA <dB>,<d B>,<dB> :CALCulate :MCPower:OF FSet:LIST: LIMit:NEGat ive[:UPPer] :DATA? Example: C[...]

Chapter 2 169 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions attenuation set to reduce the potential errors due to VSWR. Key Path: Meas Setup State Saved: Not saved. History: Added with PSA firmware revision A.02.00 Added with ESA firmware revision A.08.00 Remote Command: [:SENSe]:P OWer[:R[...]

170 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions referenced to the last meas ured value, or you may specify the reference fo r the multi-carrier power measurement. Relative values are displaye d, referenced to the “Power Reference” value. Key Path: Meas Setup State Saved: Sa[...]

Chapter 2 171 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Remote Command: [:SENSe]:M CPower:LIMi t[:STATe] OF F|ON|0|1 [:SENSe]:M CPower:LIMi t[:STATe]? Example: MCP:LIM ON MCP:LIM? 2.16.10 RRC Filter Pressing RRC Filter turns the Root Raised Cosine filt er on or off for the carrier s an[...]

172 Chapter 2 One-Button Measurement Functions Meas Setup (Multi-Carrier P ower—MCP) One-Button Measurement Functions Added with ESA firmware revision A.09.00. Remote Command: [:SENSe]:M CPower:FILT er[:RRC]:A LPHA <number> [:SENSe]:M CPower:FILT er[:RRC]:A LPHA? Example: MCP:FILT:A LPHA .33 MCP:FILT:A LPHA? 2.16.12 Noise Correction Pressin[...]

Chapter 2 173 One-Button Measurement Functions T race/View (Multi-Carrier P ower Measurement) One-Button Measurement Functions 2.17 T race/V iew (Multi-Carrier Power Measurement) If Multi-Carrie r P ower has been selected in the Measure menu of the Spectrum Analysis mode, this key displays the appropriate T race/View menu for the multi-carrier powe[...]

174 Chapter 2 One-Button Measurement Functions T race/View (Multi-Carrier P ower Measurement) One-Button Measurement Functions 2.17.3 Combined V iew Units Pressing Combined View Units selects the units ( dBc or dBm ) for the floating numeric displays when Combined is selected. Key Path: T race/View Factory Preset: dBc History: Added with PSA firmwa[...]

Chapter 2 175 One-Button Measurement Functions T race/View (Multi-Carrier P ower Measurement) One-Button Measurement Functions 2.17.4 T race One-button measurements do n ot change this function. See V olume 1, Core Spectrum Analyzer Functions User ’ s and Programmer ’ s Reference guide for information about Tr a c e and its lower -level functio[...]

176 Chapter 2 One-Button Measurement Functions T race/View (Multi-Carrier P ower Measurement) One-Button Measurement Functions[...]

Chapter 2 177 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions 2.18 Meas Setup (Occupied Bandwidth—OBW) When Occupied BW has been selected in the Measure menu of the Spectrum Analysis Mode, this key displays the appro priate measurement setup menu. The Occupied Bandwidth measurement inte grat[...]

178 Chapter 2 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions OBW:AVER O N OBW:AVER? 2.18.2 A vg Mode Enables you to select the type of terminatio n control used for the averaging function ( Exp or Repeat ). This determines the averaging action after the specified number of measurements (ave r[...]

Chapter 2 179 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions OBW:MAXH? 2.18.4 Occ BW % Pwr Enables you to change the percentage of sign al power used when de termining the occupied bandwidth. Key Path: Meas Setup State Saved: Saved in instrument state. Factory Preset: 99.0% Range: 10.0% throu[...]

180 Chapter 2 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions Remote Command: [:SENSe]:O BW:FREQuenc y:SPAN <fr eq> [:SENSe]:O BW:FREQuenc y:SPAN? Example: OBW:FR EQ:SPAN 10 MHz OBW:FREQ:S PAN? 2.18.6 x dB Enables you to specif y the power level u sed to determine the emission bandwidth [...]

Chapter 2 181 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions TIP ESA Only: This function looks simila r to the N d B Points function found under the Peak Search front-panel key . However , the N dB Points arrows are referenced to the active marker , usua lly placed on a si gnal peak, and the [...]

182 Chapter 2 One-Button Measurement Functions Meas Setup (Occupied Bandwidth—OBW) One-Button Measurement Functions[...]

Chapter 2 183 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19 Meas Setup (Spectrum Emissions Mask—SEM) When the spectrum emissions mask measurement has been selected in the Measure menu of the Spectrum Analysis Mode, this key displays the appropriate measurement setup menu. Spectru[...]

184 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19.2 Meas T ype Displays a menu where you can sele ct a measurement reference type, To t a l P w r R e f or PSD Ref . Key Path: Meas Setup Factory Preset: T otal Pwr Ref Remote Command: [:SENSE]:S EMask:TYPE TP Ref | PSDRef [[...]

Chapter 2 185 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19.3.1 Chan Integ BW Specifies the integration bandwidth used in calculating the power in the main channel. Key Path: Meas Setup , Ref Channel Factory Preset: 3.84 MHz Range: 10% to 100% of the setting of Cha n Span Remote Co[...]

186 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Remote Command: [:SENSe]:S EMask:SWEep time <numb er> [:SENSe]:S EMask:SWEep time? [:SENSe]:S EMask:SWEep time:AUTO OF F|ON|0|1 [:SENSe]:S EMask:SWEep time:AUTO? Example: SEM:SWE 4 s SEM:SWE? SEM:SWE:AU TO 1 SEM:SWE:AU TO[...]

Chapter 2 187 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19.3.5 T otal Pwr Ref or PSD Ref Displays the type of power measur ement reference sele cted using the Meas T ype key (see “Meas T ype” on page 184 ). T otal Pwr Ref is the power in the carrier that is us ed as the refere[...]

188 Chapter 2 One-Button Measure ment Functions Meas Setup (Spectr um Emissions Ma sk—SEM) One-Button Measurement Functions T able 2-2 Offsets & Limits Defaulted for W - CDMA (3GPP) Base Station Measurements Offset Start Freq (MHz) Stop Freq (MHz) Sweep Tim e ( µ s) Res BW (kHz) Abs Start (dBm) Abs Stop (dBm) Abs Couple Rel Start (dBc) Rel S[...]

Chapter 2 189 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions T able 2-3 Offsets & Limits Defaulted for W - CDMA (3GPP) Mobile Station Measurements Offset Start Freq (MHz) Stop Freq (MHz) Sweep Ti me ( µ s) Res BW (kHz) Abs Start (dBm) Abs Stop (dBm) Abs Couple Rel Start (dBc) Rel St[...]

190 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions T able 2-4 Offsets & Limits Defaulted for 802.1 1a, 802.1 1g, and HiperLAN/2 Radio Standards Offset Start Freq (MHz) Stop Freq (MHz) Sweep Ti me (ms) Res BW (kHz) Abs Start (dBm) Abs Stop (dBm) Abs Couple Rel Start (dBc) Re[...]

Chapter 2 191 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions T able 2-5 Offsets & Limits Defaulted for 802.1 1b Offset Start Freq (MHz) Stop Freq (MHz) Sweep Tim e (ms) Res BW (kHz) Abs Start (dBm) Abs Stop (dBm) Abs Couple Rel Start (dBc) Rel Stop (dBc) Rel Couple Fail Mask Meas BW [...]

192 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19.4.1 Offset Selects the offset pairs (upper and lower) th at the menu keys affe ct , and display s the memory select ion menu from A to E for ESA, or A to F for PSA (where you can store up to 6 sets of values for Star t Fre[...]

Chapter 2 193 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Offsets that are turned off, for the currently selected offset will return a -999.0 when queried. Example: SEM:OFFS:L IST:FREQ:ST AR 2 MHz SEM:OFFS:L IST:FREQ:ST AR? SEM:OFFS:L IST:STAT 1 SEM:OFFS:L IST:STAT? 2.19.4.3 Stop Freq[...]

194 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Default T erminator: s (seconds) Range: 1 ms to 42 ks Remote Command: [:SENSe]:S EMask:OFFSe t[n]:LIST: SWEeptime < time> ... [ <time>] (up to five values) [:SENSe]:S EMask:OFFSe t[n]:LIST: SWEeptime? [:SENSe]:S EMa[...]

Chapter 2 195 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions OFF|ON|0| 1 [:SENSe]:S EMask:OFFSe t[n]:LIST: BANDwidth|B WIDth[:RESo lution]:AUT O? Remote Command Notes: Comma separated list. When offset F is off, this will be 5 values. When offset F is on, this will be 6 values. n = 1 for[...]

196 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions n/a State Saved: Saved in instrument state. Factory Preset: Dependent upon Radio Standard and devi ce selected, refer to the default tables for “Offset/Limits” on page 187 for this value. Default T erminator: x Res BW Knob [...]

Chapter 2 197 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Default T erminator: dBm Range: –200 dBm to 50 dBm Remote Command: [:SENSe]:S EMask:OFFSe t[n]:LIST: STARt:ABSol ute <ampl>, ...[<ampl>] (up to five values) [:SENSe]:S EMask:OFFSe t[n]:LIST: STARt:ABSol ute? Remot[...]

198 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions SEM:OFFS:L IST:STOP:AB S SEM:OFFS:L IST:STOP:AB S:COUP 0 SEM:OFFS:L IST:STOP:AB S:COUP? 2.19.4.9 Rel Start Enables you to enter a relative level lim it at Start Freq ranging from − 150.00 to +50.00 dBc with 0.01 dB resolution[...]

Chapter 2 199 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Remote Command: [:SENSe]:S EMask:OFFSe t[n]:LIST: STOP:RCARri er <real nu mber>,[<rea l number>]. .. [:SENSe]:S EMask:OFFSe t[n]:LIST: STOP:RCARri er? [:SENSe]:S EMask:OFFSe t[n]:LIST: STOP:RCARri er:COUPle O FF|ON|[...]

200 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Remote Command: [:SENSe]:S EMask:OFFSe t[n]:LIST: TEST ABSolute|A ND|OR|RELat ive,ABSolu te|AND|OR|R ELative,ABS olute|AND|O R|RELative ,ABSolute| AND|OR|RELa tive [:SENSe]:S EMask:OFFSe t[n]:LIST: TEST? Remote Command Notes: C[...]

Chapter 2 201 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions emission mask measurement results is larger than the limit for Rel Star t and Rel Stop . Key Path: Meas Setup , Offset/Limits , More , Fail Mask State Saved: Saved in instrument state. Factory Preset: Dependent upon Radio Stand[...]

202 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Example: SENS:SEM:R ES 2.19.6 Optimize Ref Level Sets the input attenuator and reference level to optimize the robustness of the measurement, which is its freedom from e rrors due to input compression and log amp range limita t[...]

Chapter 2 203 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.19.8 Filter Alpha Press RRC Filter to input the alpha value for the RRC Filter . This parameter is only available when 3GPP W -CDMA is selected as the Radio St d. from the Mode Setup menu. Key Path: Meas Setup State Saved: Sa[...]

204 Chapter 2 One-Button Measurement Functions Meas Setup (Spectrum Emissions Mask—SEM) One-Button Measurement Functions[...]

Chapter 2 205 One-Button Measurement Functions Display (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.20 Display (Spectrum Emissions Mask—SEM) Displays menu keys that enable you to co nfigure parameters for the SEM measurement. NO TE The keys described below are measure men t dependent. T o access the display menus, for the SE[...]

206 Chapter 2 One-Button Measurement Functions Display (Spectrum Emissions Mask—SEM) One-Button Measurement Functions Key Path: Display State Saved: Saved in instrument state. History: Added with PSA firmware revision A.02.00 Added with ESA firmware revision A.08.00 2.20.3.1 Graticule (On Off) Pressing Graticule turns the display graticules On or[...]

Chapter 2 207 One-Button Measurement Functions Marker (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.21 Marker (Spectrum Emissions Mask—SEM) Displays th e Marker control m enu for the SEM measurement. If no markers are active, Marker selects marker 1, sets it to Normal and places it to the right of the display . There are two [...]

208 Chapter 2 One-Button Measurement Functions Marker (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.21.2 Normal Sets the control mode for the selected marker to Normal (see “Select Marker” on page 207 ). If the marker is off, a single marker is activated and placed on the screen to the right of the measurement graph. Y ou c[...]

Chapter 2 209 One-Button Measurement Functions SP AN X Scale (Spectrum Emissions Mask—SEM) One-Button Measurement Functions 2.22 SP AN X Scale (Spectrum Emissions Mask—SEM) Activates the Span function for the SEM me asurement and displays th e menu of span functions. Key Path: Front-panel key State Saved: Saved in Instrument State Remote Comman[...]

210 Chapter 2 One-Button Measurement Functions SP AN X Scale (Spectru m Emissions Mask—SEM) One-Button Measurement Functions extreme right line of the display graticule. Key Path: MEASURE , Spectrum Emission Mask , SP AN X Scale Factory Preset: Center[...]

Chapter 2 211 One-Button Measurement Functions T race/View (Spectrum Emissions Mask) One-Button Measurement Functions 2.23 T race/V iew (Spectrum Emissions Mask) If Spectrum Emission Mask has been selected in th e Measure menu of the Spectrum Analysis mode, this key displays the appropriate T race/View menu for the spectrum emission mask (SEM). Dis[...]

212 Chapter 2 One-Button Measurement Functions T race/View (Spectrum Emissions Mask) One-Button Measurement Functions Remote Command: There is no remote co mm and for this function. 2.23.3 Integrated Power Press Integrated P ower to view the measurement results of Spectrum (Ref: T otal Pwr , Seg: Offset) measurements in the graph window as integrat[...]

Chapter 2 213 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions 2.24 Meas Setup (Spurious Emissions) When the spurious emissi ons measurement h as been selected in the Mea sure menu of the Spectrum Analysis mode, this key displays the appropriate measurement setup menu. The spurious emissions m easure[...]

214 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions count) is reached. • EXP (Exponential A veraging mode)—Whe n you set Av g M o de to Exp , each su ccessive data acquisition after the average count is reached is exponentially weighted a nd combined with the existing av erage. Expo ne[...]

Chapter 2 215 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions indicate this range is currently inactive. Key Path: Meas Setup Saved State: All values for al l range s are saved in instrument state. Factory Preset: For each range, the following setti ngs are selected: . Video BW (Auto), Sweep Time (A[...]

216 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: There is no equivalent remote command. 2.24.3.1 Range Selects a range and updates the values on the other Range T able keys so that they reflect the settings for the selected range. If Range is set to On it is used as part[...]

Chapter 2 217 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Increment: 1, 1.5, 2, 3, 5, 7.5, 10,... Range: Frequency range of your analyzer . Remote Command: This parameter can re ceive up to 20 valu es. The location in the list sent corresponds to the range the value is associated with. Missing v[...]

218 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Step Key Increment: Steps through the available resolution bandwidth filters. Range: Resolution bandwidth range of your analyzer . Remote Command: This parameter can re ceive up to 20 values . The location in the list sent corresponds to [...]

Chapter 2 219 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions 2.24.3.6 Sweep T ime Sweep Time is used to set the swee p time of the analyzer . When Au t o is selected the analyzer determines the optimum se tting, while Man enables you to determine the setting. Key Path: Meas Setup , Range T able Fac[...]

220 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Step Key Increment: 1 dB Range: –150 dBm to 50 dBm History: Added with PSA firmware revision A.03.00 Added with ESA firmware revision A.09.00 Remote Command: :CALCulate :SPURious[: RANGe][:LI ST]:LIMit:A BSolute[:UP PER]:DATA:S TARt <[...]

Chapter 2 221 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: :CALCulate :SPURious[: RANGe][:LI ST]:LIMit:A BSolute[:UP PER]:DATA:S TOP <integer>, <integer> :CALCulate :SPURious[: RANGe][:LI ST]:LIMit:A BSolute[:UP PER]:DATA:S TOP? :CALCulate :SPURious[: RANGe][:LI ST]:LI[...]

222 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions 2.24.3.10 Pk Threshold Pk Threshold sets the minimum amplitude of signals that can be identified as peaks. For example, if a value of -90 dBm is selected, only peaks that rise and fall more than the peak excursion value and are above the [...]

Chapter 2 223 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: [:SENSe]:S PURious[:RA NGe][:LIST ]:ATTenuati on [:SENSe]:S PURious[:RA NGe][:LIST ]:ATTenuati on? Remote Command Notes: The query always returns 20 values Example: SPUR:RANG:LIST:ATT 20,20,20,20,20,2 0 2.24.3.12 Detector [...]

224 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: [:SENSe]:S PURious[:RA NGe][:LIST ]:POINts[:F UNCtion] NORMal|AVE Rage|POSiti ve|SAMPle| NEGative|QP Eak|EAVerag e|EPOSitive |MPositive [:SENSe]:S PURious[:RA NGe][:LIST ]:DET? Example: SPUR:POIN QPE 2.24.3.13 Detector 2 P[...]

Chapter 2 225 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions History: Added with PSA firmware revision A.06.00 Remote Command: [:SENSe]:S PURious[:RA NGe][:LIST ]:POINts[:F UNCtion] OFF|NORMal |AVERage|PO Sitive|SAM Ple|NEGativ e|QPEak|EAV erage| EPOSitive| MPositive [:SENSe]:S PURious[:RA NGe][:LI[...]

226 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: See “Detector 2” on page 224 . 2.24.3.13.3 Peak PSA Only: For each interval (bucke t) in the trace, Peak detection displays the highest amplitude withi n the interval. Peak detect ion is u sed for CW measurements and s[...]

Chapter 2 227 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions 2.24.3.14 Negative Peak For each interval (bucket) in the trace, Negative P eak detection displays the lowest sample within the interval. When Negative P eak is selected, NPk a ppears on the left side of the displa y . Key Path: Meas Setu[...]

228 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions State Saved: Saved in instrument state. History: Added with PSA firmware revision A.06.00 Remote Command: See “Detector 2” on page 224 . 2.24.3.14.4 MIL Peak Selects peak detection using the MIL specifications . Key Path: Meas Setup ,[...]

Chapter 2 229 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions Remote Command: [:SENSe]:S PURious[:RA NGe][:LIST ]:SWEep:POI Nts [:SENSe]:S PURious[:RA NGe][:LIST ]:SWEep:POI Nts? [:SENSe]:S PURious[:RA NGe][:LIST ]:SWEep:POI Nts:AUTO [:SENSe]:S PURious[:RA NGe][:LIST ]:SWEep:POI Nts:AUTO? 2.24.4 Mea[...]

230 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions State Saved: Saved in instrument state. Factory Preset: Examine Range: Examine|Full Remote Command: [:SENSe]:S PURious:TYP E EXAMine|FU LL [:SENSe]:S PURious:TYP E? Remote Command Notes n/a Example: SPUR:TYPE FU LL 2.24.5 Spur Enables you[...]

Chapter 2 231 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions recalculated for each active range th e value is not stored in instrument state. Factory Preset: 0.00 dBm Knob Increment: 1 Step Key Increment: 10 Range: –180 dBm to 20 dBm, wi thout referenc e level offset Remote Command: [:SENSe]:S PU[...]

232 Chapter 2 One-Button Measurement Functions Meas Setup (Spurious Emissions) One-Button Measurement Functions[...]

Chapter 2 233 One-Button Measurement Functions Display (Spurious Emissions) f or PSA Only One-Button Measurement Functions 2.25 Display (Spurious Em issions) for PSA Only Displays menu keys that enable you to conf igure pa rameters for the spurious emissions measurement. NO TE The keys described below are measure men t dependent. T o access the dis[...]

234 Chapter 2 One-Button Measurement Functions Display (Spurious Emissions) f or PSA Only One-Button Measurement Functions Te r m i n a t o r s : Enter History: Added with PSA firmware revision A.06.00 2.25.2.2 Annotation (On Off) T urns the screen annotation on or off, howe ver , menu key annotation will remain on the display . The screen annotati[...]

Chapter 2 235 One-Button Measurement Functions Marker (Spurious Emissions) for PSA Onl y One-Button Measurement Functions 2.26 Marker (Spurious Emi ssions) for PSA Only Displays the Mar ker contro l me nu for the spurious emissions measurement. If no markers are active, Marker selects marker 1, sets it to Normal and places it to the right of the di[...]

236 Chapter 2 One-Button Measurement Functions Marker (Spurious Emi ssions) for PSA Onl y One-Button Measurement Functions displayed measurement graph. Se tting a marker to state OFF or 0 selects that marker and turns it off. The respon se to the query will be 0 if OFF , 1 if ON. Example: CALC:SPUR: MARK2:STAT ON selects marker 2. CALC:SPUR: MARK:S[...]

Chapter 2 237 One-Button Measurement Functions Marker (Spurious Emissions) for PSA Onl y One-Button Measurement Functions selected marker . Key Path: Marker Factory Preset: Off History: Added with PSA firmware revision A.06.00 Remote Command: See “Select Marker” on page 235 for the command to select the control mod e. Example: CALC:SPUR: MARK3:[...]

238 Chapter 2 One-Button Measurement Functions Marker (Spurious Emi ssions) for PSA Onl y One-Button Measurement Functions Example: CALC:SPUR: MARK:AOFF turns off all markers.[...]

239 Menu Maps : One- Button Measurement Functions 3 Menu Maps: One-Button Measurement Functions This chapter provides you with menu maps for all measurements ava ilable to you when you press the front-panel Measure[...]

240 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps This section provides a visual representati on of all front-panel key menus ass ociated with the measurements available when you press the front -pane l Measure key . The key menus c[...]

Chapter 3 241 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Directions for Use Refer to the following notes to utilize the key-flow diagrams: • Start from the upper left corner of each m easurement diagram. Go to the right, an d go from the top to the bottom. • When ch[...]

242 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions MEASURE Key Measure Channel Power Harmonic Distortion Meas Off ACP Occupied BW Power Stat CCDF MEASURE Multi Carrier Power More 1 of 2 Burst Power Intermod (TOI) Spurious Emissions Spectrum Emission Mask More 2 of 2[...]

Chapter 3 243 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Meas Control Key Restart Measure Single Cont Pause Meas Control Key toggles between Pause and Resume Mea s Control pe883a[...]

244 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Mode Setup Key for ESA Mode Setup Mode Setup Enable All Measurements Yes No Retain Params On Off Radio Std None Std Setup IS-95 J-STD-008 NADC GSM/EDGE 3GPP W-CDMA More 1 of 3 cdma2000 SR1 cdma2000 SR3- MC cdma2000 [...]

Chapter 3 245 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Mode Setup Key for PSA Mode Setup Mode Setup Enable All Measurements Yes No Retain Params On Off Radio Std None Std Setup IS-95A J-STD-008 IS-95C GSM/EDGE 3GPP W-CDMA More 1 of 3 cdma2000 MC-1X cdma2000 MC-3X cdma[...]

246 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Mode Setup Key for PSA (2 of 3) If Radio St d is None this menu ap pears: If Radio Std is Bluetooth this menu app ears: If Radio Std is IS-95A, J-STD-008, cdma2000, W-CDM A, NA DC, PDC, TETRA or GSM/EDGE this menu a[...]

Chapter 3 247 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Mode Setup Key for PSA (3 of 3) HiperLAN/2 W-LAN 802.11a 802.11b 802.11g DVB-T L/SECAM/ NICAM G/PAL/NICAM I/PAL/NICAM System E S-DMB UWB UWB Indoor mode setup (3) ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ ‡ UWB S-DMB DVB-[...]

248 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions ACP Measurement: Meas Setup Key If meas urement chosen is : ACP Meas Setup Opt imize Ref Level Avg Number 10 On Off Chan Integ BW 1.2300 MHz Avg Mode Exp Repeat Meas Setup Method IBW Total Pwr Ref -6.78 dBm Auto Man[...]

Chapter 3 249 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions ACP Measurement: T race/V iew Key Trace/Vie w Note: The menus under Trace/View are measurement dependent and vary with each measurement Meas View Bar Graph Spectrum Combined Combined View Units Rel Abs If measurem[...]

250 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Burst Power Measurement: Meas Setup Key If measurem ent chosen is: Burst Power Meas Setup Optimize Ref Level Avg Number 10 On Off Threshold Lvl -30.00 dB Abs Rel Avg Mode Exp Repeat Average Type Log RMS Burst Width [...]

Chapter 3 251 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Burst Power Measurement: T race/V iew Key Trace/Vi ew Note: The menus under Trace/View are measurement dependent an d vary w ith each measurement If m eas urem ent cho sen is: Burst Power Meas View Combined RF Env[...]

252 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions CCDF (Power Stat) Measur ement: Meas Setup Key Meas BW 5.0 MHz Counts 100.0 kpts Meas Interval 1.00 ms Optimize Ref Level Meas Setup If measurem ent chosen is: Power Stat CCDF Meas Setup Note: The m enus under Meas [...]

Chapter 3 253 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions CCDF (Power Stat) Meas urement: Display Key Display Display Ref Trace On Off Preferences Full Screen If m easurem ent chosen is : Power Stat CCDF Note: The m enus under Display are m easurem ent dependent and vary[...]

254 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions CCDF (Power Stat) Meas urement: Marker Key Marker Marker Trace Gaussian Reference Measured † † Marker All Off Marker Delta Select Marker 1 2 3 4 Normal Off marker_ccdf Note: The m enus under Marker are meas urem[...]

Chapter 3 255 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions CCDF (Power Stat) Measur ement: Span X Scale Key X Scale Scale/Div 2.00 dB SPAN X Scale Note: The m enus under Span are m easurem ent dependent and m ay vary with each m easurem ent If m easurem ent chosen is : Po[...]

256 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions CCDF (Power Stat) Measur ement: T race/V iew Key Trace/View Note: The m enus under Trace/View are m easurem ent dependent and vary with each meas urement If m easurem ent chosen is: Power Stat CCDF Meas View CCDF vi[...]

Chapter 3 257 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Channel Power Measurem ent: Meas Setup Key If measurem ent chosen is: Channel Power Meas Setup Avg Number 10 On Off Chan Pwr Span 3.00000000 MHz Integ BW 2.00000 MHz Avg Mode Exp Repeat Meas Setup Optimize Ref Lev[...]

258 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Channel Power Measurement: T race/V iew Key Trace/Vi ew If m easu rem ent chos en is : Channel Power Meas View Combined Spectrum Trace Blank View Max Hold Min Hold Trace 1 2 3 Clear Wri te Note: The menus under Trac[...]

Chapter 3 259 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Harmonic Distortion Meas urement: Meas Setup Key[...]

260 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Harmonic Distortion Meas urement: T r ace/V iew Key Trace/View Note: The m enus under Trace/Vi ew are measurement dependent and vary with each measurem ent If m easurem ent chosen is: Harmonic Distortion Meas View H[...]

Chapter 3 261 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Intermod (TOI): Meas Setup Key Meas Setup Optimize Ref Level Avg Number 10 On Off TOI Span 15 MHz Max Mixer Lvl -30.00 dB Auto Man Avg Mode Exp Repeat M ea s Se t u p If m easurem ent chosen is : Intermod (TOI) No[...]

262 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Multi-Carrier Power Measur ement: Meas Setup Key Meas Setup Meas Setup Avg Number 10 On Off Avg Mode Exp Repeat Carrier Setup Offset/Limits Carrier Result 1 Optimize Ref Level More 1 of 2 Meas Setup Method IBW RBW P[...]

Chapter 3 263 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Multi-Carrier Power Measur ement: T race/V iew Key Trace/Vi ew Note: The menus under Trace/View are measurement dependent and vary with each measurement If measurement chosen is: Multi Carrier Power Meas View Spec[...]

264 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Occupied Bandwidth Measurement: Meas Setup Key Meas Setup OBW Span 3.0000000 MHz x dB -26.00 dB Optimize Ref Level Avg Number 10 On Off Occ BW % Pwr 99.00 % Max Hold On Off Avg Mode Exp Repeat If measurement chosen [...]

Chapter 3 265 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Spectrum Emission Mask M easurement: Meas Setup Key Mea s Setu p If m easur ement c hosen is: Spectrum Emis sion Mask Meas Setup Optimize Ref Le vel Avg Number 10 On Off Ref Channel Chan Integ B W 3.8400 MHz More [...]

266 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Spectrum Emission Mask Measurement: Display Key Display Display Limit Display On Off Preferences Full Screen If m easurem ent chosen is : Spectrum Emission Mas k Note: The m enus under Display are m easurem ent depe[...]

Chapter 3 267 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Spectrum Emission Mask Measurement: Marker Key Select Marker 1 2 3 4 Off Normal Marker Marker -> If m easurem ent chosen is : S pect r um Em iss io n M as k Note: The m enus un der Marker are m easurem ent depe[...]

268 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Spectrum Emission Mask M easurement: Spa n X Scale Key X Scale Scale/Div 2.00 MHz SPAN X Sc al e Note: T he menus u nder Span are m easurem ent dependent and m ay vary with each m easurem ent If m easurem ent chosen[...]

Chapter 3 269 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Spectrum Emission Mask M easurement: T race/V iew Key Trace/View Note: The m enus under Trace/Vi ew are measurement dependent and vary with each meas urement If m easurem ent chosen is : Spectrum Emission Mas k Me[...]

270 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Spurious Emissions Measurement: Meas Setup Key Meas Se tup Avg Number 10 On Off Avg Mode Exp Repea t Range Ta bl e Meas Typ e Ex am ine Full Spur 0 Ref Level 0.00 dBm Au to O n Range 1 On Off Start Freq 1.92000000 G[...]

Chapter 3 271 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Spurious Emissions Measuremen t: Meas Setup Key (2 of 2) Normal Peak Sample Negati ve Peak Quasi Pe ak Average Detector 1 More 1 of 2 EMI Avera ge MIL Peak EMI Peak Detector 1 More 2 of 2 Off Average Peak Sample N[...]

272 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions Spurious Emissions Measurement: Display PSA Onl y Display Display Preferences Full Screen If measurement chosen i s: Sp u rio us E m issi on s Note: The menus under Displ ay are measur ement dependent and vary wit h[...]

Chapter 3 273 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps : One- Button Measurement Functions Spurious Emissions Measurement: Marker Selec t Marker 1 2 3 4 Delt a Normal Marker Marker Off Marker s Al l Off If meas urement chosen i s: S puri ous E m i ss i on s Note: The m enus under Marker are meas urem en[...]

274 Chapter 3 Menu Maps: One-Button Measurement Functions One-Button Measurement Menu Maps Menu Maps: One-Button Measurement Functions[...]

Index 275 Index Symbols *RST , 27 Numerics 3GPP W -CDMA key , 36 802.1 1a key , 40 802.1 1b key , 41 802.1 1g key , 42 A absolute limit , 219 , 220 Absolute Limit key , 219 , 220 ACP Meas Setup menu , 248 T r ace/View menu , 249 ACP key , 62 adjacent channel power key , 62 measurement , 62 measurement setup , 89 adjacent channel power measurement m[...]

276 Index Index Fast key , 99 Fast Spurious T es t key , 231 fast spurious tes ting , 231 FCC Part 15 key , 40 FETCh commands , 54 Filter Alpha key , 103 , 136 , 171 , 203 frequency offset, ACP , 91 front-panel features (see Getting Started guide ) , 27 front-panel key Display , 121 , 205 , 233 Input/Output , 154 , 155 Marker , 125 , 207 , 235 Meas[...]

Index 277 Index Meas Setup key , 261 Method key , 97 , 169 mobile station setup , 47 mode points , 228 Mode Setup menu , 244 , 245 , 246 , 247 Mode Setup front-panel key , 33 moving trace data , 151 , 21 1 , 212 multi carrier power measuremen t trace , 173 viewing trace , 173 Multi-Carrier Power Meas Setup menu , 262 T r ace/View menu , 263 multi-c[...]

278 Index Index Stop Freq key , 217 stop frequency , 217 Store Ref T race key , 121 sweep time , 148 , 149 , 219 Sweep T ime key , 148 , 149 , 185 , 219 T table range , 144 , 214 setting range , 143 , 145 , 216 terms *RST , 27 book , 27 definition , 27 dependencies/couplings , 27 example , 27 factory preset , 27 maximum value , 27 remote command , [...]