AirLive IP-200PHD manual

      i IP-200PHD 2.0 Mega Pixel Passive PoE IPCamera User’s Manual[...]

Copyright & Disclaimer i  AirLive IP-200PHD User’s Manual Copyright & Disclaimer No part of this publication may be reproduced in any form or by any means, whether electronic, mechanical, photocopying, or recor ding without the written consent of OvisLink Corp. OvisLink Corp. has made the best effort to ensure the accuracy of the inf o[...]

Copyright & Disclaimer   AirLive IP-200PHD User’s Manual ii FCC Statement Federal Communication Commission Interf erence Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf[...]

Table of Contents iii  AirLive IP-200PHD User’s Manual Table of Contents 1. Introduction ..................................................................................................... 5 1.1 Overview ........................................................................................... 5 1.2 Features ................................[...]

Table of Contents   AirLive IP-200PHD User’s Manual iv 4.2.2 DDNS ..................................................................................... 30 4.2.3 PPPoE .................................................................................... 32 4.2.4 Steaming ........................................................................[...]

1. Introduction 5  AirLive IP-200PHD User’s Manual 1 1. Introduction    1.1 Overview This camera is an inexpensive and fully scalable surveillance device. Because the Network Cameras can be plugged into your existing local area network (LAN), you will potentially save thousands of dollars from unnecessary cabling. The device is access[...]

1. Introduction   AirLive IP-200PHD User’s Manual 6 1.2 Features  z Easy installation with setup wizard (IP Wizard II) z UPnP device discovery and NAT router transversal for easy installation z Dynamic IP Service, DIPS®, to search your IP camera from Internet easily z H.264, MPEG4 and JPEG triple compression simultaneously z 2 Mega-pixe[...]

1. Introduction 7  AirLive IP-200PHD User’s Manual 1.4 Package Contents  User can find the following items in the package: z This camera is the main element of the product. z Camera Stand with screws z Power adapter dedicates 12V DC electric power output to Network Camera. z User’s manual CD provides important information and instructions[...]

1. Introduction   AirLive IP-200PHD User’s Manual 8 2. Microphone The Camera has built-in an internal microphone. This microphone is hidden in the pinhole located on the front panel. 3. Micro SD Card Slot User can insert a micro SD card into this slot for event recording. Note: The product picture is WN-200HD and IP-200PHD without the anten[...]

1. Introduction 9  AirLive IP-200PHD User’s Manual 3. Factory Default Reset This button is hidden in the pinhole. Th is button is used to restore the all factory default settings. Sometimes re starting the camera will make the system back to a normal stat e. If the system still got problems after restart, user can restore the fact ory default [...]

1. Introduction   AirLive IP-200PHD User’s Manual 10 3. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket located on the Network Camera’s bottom and attach it to the network. 4. Connect the external power supply to Camera Connect the attached power adapter to the DC power jack of the Network Camera.[...]

1. Introduction 11  AirLive IP-200PHD User’s Manual Note : Use the power adapter, 12VDC, included in the package and connect it to wall outlet for AC power. 5. Use PoE-1P to connect to a net work device (for IP-200PHD only) The IP-200PHD is using DC 12V passive PoE and you can use PoE-1P as PoE splitter or PoE injector to connect to your netwo[...]

2. Getting Started   AirLive IP-200PHD User’s Manual 12 2 2. Getting Started 2.1 IP Wizard Once you have installed the Network Camera well and powered it on, the network accessing type LED will turn on. It means the system is booting up successfully. Furthermore, if you hav e a proper network connection, and access to the Network Camera, th[...]

2. Getting Started 13  AirLive IP-200PHD User’s Manual When launch the IPWizard II, a searchi ng window will pop up. IPWizard II is starting to search Network Cameras on t he LAN. The existed devices will be listed as below.[...]

2. Getting Started   AirLive IP-200PHD User’s Manual 14 2.1.1 View If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furt hermore you could double click the left button of mouse to link to the network de[...]

2. Getting Started 15  AirLive IP-200PHD User’s Manual You could modify the relative setti ngs of the selected device. Click “ << ” button will quit the LAN setting procedure and click “ >> ” button will move to next page as below.[...]

2. Getting Started   AirLive IP-200PHD User’s Manual 16 In case, you do not want to change user name and/or password, then just click “ Submit ” button to perform your se tting accordingly. Click “ << ” button will go back to previous page. If you like to change username and/or passw ord of the device, just click the check but[...]

2. Getting Started 17  AirLive IP-200PHD User’s Manual To discover your device, go to your Desktop and click My Network Places . Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically. 2.3 Install the IP Camera behind NAT router Once installed, the device is accessible on your LAN. To access the dev[...]

2. Getting Started   AirLive IP-200PHD User’s Manual 18 (1) Enable UPnP option of your NAT router To use UPnP IGD function (NAT traver sal), you need to make sure the UPnP function is enabled in your router. Most new home routers should support this function. Some of routers are defaul t enable and others are not. Please check user’s manu[...]

2. Getting Started 19  AirLive IP-200PHD User’s Manual 2. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the first ti me use (default value), input the User Name: admin Password: airlive That’s, type in “ admin” on the “USERNAME” as a default name and “ airlive” on the “PASSWORD” as [...]

2. Getting Started   AirLive IP-200PHD User’s Manual 20 2.4.2 Login as Administrator If you log in the Camera as the Administrator, you can perform all the settings provided by the device. Start-up screen will be as follow no matter an ordinary users or an administrator. ActiveX Control Monitor Image 2-Way Audio Full Screen[...]

3. Configure the Camera 21  AirLive IP-200PHD User’s Manual 3 3. Configure the Camera 3.1 Monitor the Image Section The image shot by the device is shown here. The date and time are displayed at the top of the window. 3.2 View Profile The device supports multi-profile function for H.264, MEPG4 and JPEG simultaneously. User can chose the proper[...]

3. Configure the Camera   AirLive IP-200PHD User’s Manual 22 : Disable audio up loading function. : Enable audio uploading function. 3.6 Full Screen Enlarge video to full screen display. : Enlarge video to full screen disp lay. Press “ESC” key to disable this function. 3.7 Active Control The plug-in ActiveX control supports a lo t of fu[...]

3. Configure the Camera 23  AirLive IP-200PHD User’s Manual 3.7.1 Digital Zoom Click Digital Zoom to active this function as abov e. User can drag or scale the box over the video to adjust zoom ratio and position.[...]

3. Configure the Camera   AirLive IP-200PHD User’s Manual 24 3.7.2 Snapshot Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as J PEG format into your local PC. Select Browser , the pop-up window to select the save path and file name prefix, select OK to continue. If you like to retr[...]

3. Configure the Camera 25  AirLive IP-200PHD User’s Manual Click Record to activate this function. Press Record button to start recording. The video file is saved as ASF format in to your local PC. While you want to stop it, press Stop to stop recording. Select Brow ser , the pop-up window to select the save path and file name prefix, select [...]

3. Configure the Camera   AirLive IP-200PHD User’s Manual 26 3.7.5 About Click About to show this ActiveX information.[...]

4. Monitor the Image Section 27  AirLive IP-200PHD User’s Manual 4 4. Monitor the Image Section 4.1 Monitor the Image Section This function is only available for user logged into Camera as administrator . Click on each menu name to display its setting page. Item Action Network Configure Network settings such as DHCP, DDNS, 3GPP, PPPoE and UPnP[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 28 4.2 Configure via Web UI 4.2.1 Network  Use this menu to configure the network to connect the device and the clients. This section provides the menu fo r connecting the device through Ethernet cable. MAC address: Displays the Ethernet MAC address of t he device. Note that [...]

4. Monitor the Image Section 29  AirLive IP-200PHD User’s Manual IP address, Subnet mask, and Gateway: If you do not select Obtain an IP address automatically , then you need to enter these network parameters manually. Obtain DNS from DHCP: DNS: Stands for Domain Name System. Enable this checked box when a DHCP se rver is installed on the netw[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 30 4.2.2 DDNS  DDNS: Stands for Dynamic Domain Name Server Your Internet Service Provider (ISP) provides you at least one IP address which you use to connect to the Inte rnet. The address you get may be static, meaning it never changes, or dynamic, meaning it’s likely to ch[...]

4. Monitor the Image Section 31  AirLive IP-200PHD User’s Manual DDNS: To enable or disable the DDNS service here. Server name: Choose the built-in DDNS server. DDNSHost: The domain name is applied of this device. User name: The user name is used to log into DDNS. Password: The password is used to log into DDNS.[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 32 4.2.3 PPPoE  PPPoE: Stands for Point to Point Protocol over Ethernet A standard builds on Ethernet and Point-to-P oint network protocol. It allows your device with xDSL or cable connects with broadband network directly, then your device can dial up and get a dy namic IP ad[...]

4. Monitor the Image Section 33  AirLive IP-200PHD User’s Manual PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE servic e which is provided by the ISP. Password: Type the password for the PPPoE service which is provided by the ISP. IP address, Subnet mask, and Gateway (read only): Shows the IP in[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 34 4.2.5 UPnP UPnP is short for Universal Plug and Play , which is a networking architecture that provides compatibility among networking equipment, software, and peripherals. This device is an UPnP ena bled Network Camera. If your operating system is UPnP enabled, the device wi[...]

4. Monitor the Image Section 35  AirLive IP-200PHD User’s Manual UPnP: To enable or disable the UPnP service here. Friendly Name: Shows the friendly name of this device here. UPnP NAT Traversal When enabled, the device will attempt to configure port mapping in a NAT router on your network, using UPnP™. Note that UPnP™ must be enabled in th[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 36 4.2.6 Bonjour Bonjour, also known as zero-configur ation networking, enables automatic discovery of computers, devices, and se rvices on IP networ ks. Bonjour uses industry standard IP protocol s to allow devices to aut omatically discover each other without the need to enter[...]

4. Monitor the Image Section 37  AirLive IP-200PHD User’s Manual 4.2.7 IP Filter You can enter different user’s IP address which are allowing enter or denying by the device. IP Filter: To enable or disable the IP filter function here. IP Filter Policy : Choose the filter policy wher e is denying or allowing. 4.2.8 IP Notification In case the[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 38 Subject: Type the subject/title of the E-mail. TCP Notification: If enable this function, then the “ TCP Server “, “ TCP Port ”, and “ Message ” fields need to be filled. TCP Server: Type the server name or the IP address of the TCP server. TCP Port: Set port numb[...]

4. Monitor the Image Section 39  AirLive IP-200PHD User’s Manual URL: Type the server name or the IP address of the HTTP server. HTTP Login name: Type the user name for the HTTP server. HTTP Login Password: Type the password for the HTTP server. Proxy Address: Type the server name or the IP address of the HTTP Proxy. Proxy Port: Set port numbe[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 40 4.3 Camera – Adjust Camera Parameters Use this menu to set the functions of the camera parameters of the device. 4.3.1 Picture  Rotation: Turn the “Mirror” and “Vertical Flip” On or OFF. The im age will be overturned as below.[...]

4. Monitor the Image Section 41  AirLive IP-200PHD User’s Manual White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance. Exposure Control: Auto: will adjust the inte rnal gain automatically. Hold: will hold the internal gain. Color Level: Large value will be colorful. Brightness: Large value will br[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 42 Level Defines the gray level of mask block. The lower value will be darker.[...]

4. Monitor the Image Section 43  AirLive IP-200PHD User’s Manual 4.4 System – Configure and Maintain Use this menu to perform the prin cipal settings of the device. 4.4.1 System DIPS (Dynamic IP Service): To enable or disable the DIPS® (Dynamic IP Service) function. Device ID (for DIPS): It’s a unique number of each device for identificat[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 44 To use this service, just follow four steps below: (1) Enable DIPS function of the device. (2) Check your Device ID from this page. This is a unique number for each device. (3) If your device is behind a NAT router , please configure your device properly. You could refer to s[...]

4. Monitor the Image Section 45  AirLive IP-200PHD User’s Manual To turn on or off Power LED. Log: User can check the system log informa tion of the device, including the Main Info , Appended Info , Operator IP , and so on … Reload: Click this button; user can refresh the log information of the device. 4.4.2 Date & Time You can setup the[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 46 Set the time difference from Greenwic h Mean Time in the area where the device is installed. Daylight Saving: Disable or enable the dayli ght saving adjustment. 4.4.3 Maintenance Hard Factory Default (Include the network setting): Recall the device hard factory default settin[...]

4. Monitor the Image Section 47  AirLive IP-200PHD User’s Manual To take a backup of all of the parameters, click this but ton. If necessary, it will then be possible to return to the prev ious settings, if settings are changed and there is unexpected behavior. Restore Setting: Click the “ Brow se” button to locate the saved backup file an[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 48 4. Click “ Browse ” button. Select the Firmware binary file. ( Note that it must make sure that the Firmware only applies to this device, once update, it will be burned into FLASH ROM of system.) 5. Once the firmware file was selected, click “ Firmware Upgrade ” butto[...]

4. Monitor the Image Section 49  AirLive IP-200PHD User’s Manual 4.5.1 Common Text Overlay Setting: There are some important informati on can be embedded into image, including date, time, and/or text. Video Profile: User can only choose either 720P or 2 Mega modes. The 720P mode can serve H.264 and JPEG streams up to 1280 x720 resolution simul[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 50 4.5.2 Video Profile Name: Assign a name to the selected profile. Video Type: Video codec of the se lected video profile. Resolution: Resolution of the selected video profile. ROI: Assign the selected profile as a ROI stream or not. Rate Control: Defines the rate control metho[...]

4. Monitor the Image Section 51  AirLive IP-200PHD User’s Manual For VBR, user should choose the quality level to set the video quality rather than bit rate. The quality level is bet ween 1 and 100. The higher value can reach the better quality but of course will consume higher bandwidth. For ECBR, the video bitrate is based on normal CBR mode[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 52 4.5.3 ROI ROI means Region of Interest. Use this page to specify ROI window which ROI is QVGA resolution . 4.6 Audio – Audio Parameters 4.6.1 Setting[...]

4. Monitor the Image Section 53  AirLive IP-200PHD User’s Manual Audio: To enable or disable audio function Mute While PT: Mute the audio while pan and/or tilt motion Audio Mode: To select Simplex or Fu ll duplex (2-way audio) mode Input Gain: To adjust gain of input audio Output Gain: To adjust gain of output audio 4.6.2 Manage User Name, P a[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 54 Access Right: Administrator can access every function in this device. However, Viewers only can view the video and access limited function. PTZ Control: Authorize this user to control PTZ function or not. Add, update, and remove of Users account: Manage the user’s account o[...]

4. Monitor the Image Section 55  AirLive IP-200PHD User’s Manual SMTP Server: Type the SMTP server name or the IP address of the SMTP server. Test: Send a test mail to mail server to che ck this account is available or not. SMTP Port: Set port number of SMTP service. SSL: Enable SSL function or not. SMTP Authentication: Select the authenticati[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 56 Add and Del: To add or delete the moti on windows. User can specify up to 10 Included and/or Excluded windows to monitor the video captured by this device. By dragging mouse on the image, you can change the position and size of the selected motion window accordingly. Included[...]

4. Monitor the Image Section 57  AirLive IP-200PHD User’s Manual Sensitivity Defines the sensitivity value of motion detection. The higher value will be more sensitivity. 4.6.5 Storage – Status and Configuration of SD card This page shows the status of atta ched SD card. You may setup related parameters to manage the attached SD card also. E[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 58 4.6.6 Recording List- Files List Inside SD Card This page shows the files list information. User may play or delete the selected file. 4.6.7 Event Sever FTP Server z You may setup FTP parameters for further operation of Event Schedule. That’s, if users want to send the alar[...]

4. Monitor the Image Section 59  AirLive IP-200PHD User’s Manual Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server. Test: Check the FTP server whether this account is available or not. FTP Login name: Type the use[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 60 FTP Path: Set working directory path of FTP server. FTP Passive Mode: Select passive or active mode connecting to FTP server. TCP Server z In addition to send video file to FTP se rver, the device also can send event message to specified TCP server. Name: User can specify mul[...]

4. Monitor the Image Section 61  AirLive IP-200PHD User’s Manual HTTP Server z The  device  also  can  send  event  message  to  specified  HTTP  server. Name: User can specify multiple HTTP server s as wish. Therefor e, user needs to specify a name for each HTTP server setting. URL: Type the server name or the IP[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 62 Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Proxy Port: Set port number of Proxy. SAMBA Server z The device also can send video str eam to specified SAMBA server. Name: User can specify multiple HTTP ser[...]

4. Monitor the Image Section 63  AirLive IP-200PHD User’s Manual SAMBA Login name: Type the user name for the SAMBA server. SAMBA Login Password: Type the password for the SAMBA server. SAMBA Path: Set working directory path of SAMBA server. 4.6.8 Event Schedule This menu is used to specify the sc hedule of Event or Schedule Trigger and activa[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 64 Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time slot. Trigger by: Select the triggered sources. Action: Define the actions once event triggered. Example 1: Send file to FTP server by motion triggered always: 1. Select event trigger 2. Enable tim[...]

4. Monitor the Image Section 65  AirLive IP-200PHD User’s Manual Example 2: Send file to E-Mail server by motion tr iggered from Friday 18:00 to Saturday 06:00 1. Select event trigger. 2. Enable time: start from Friday 18: 00 and keep work in 12 hous, so it will stop on Saturday 06:00. 3. Trigger by : Motion Area (A dded in Object Detection pa[...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 66 Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. 1. Type: Select schedule trigger and interval is 10-minute. 2. Enable time: Select Monday to Fr iday, and set start time from 18:00 and keep work in 6 hours. 3. Trigger by : You do not [...]

4. Monitor the Image Section 67  AirLive IP-200PHD User’s Manual Record z User can choose the type of record f ile for event or schedule application. Record File Type: Choose JPEG, AVI-JPEG, or AVI-H.264 file format. Record File Prefix: Define the prefix of recorded filename. JPEG Picture Numbers: Define the picture numbers of JPEG to be sent [...]

4. Monitor the Image Section   AirLive IP-200PHD User’s Manual 68 Post-Trigger Duration: Define the maximum duration of post-alarm. Max File Size: Define the maximum buffer size of record file.[...]

5. Troubleshooting & FAQ 69  AirLive IP-200PHD User’s Manual 5 5. Troubleshooting & FAQ 5.1 Monitor the Image Section Question Answer or Resolution Features The video and audio codec is adopted in the device. The device utilizes H.264, MPEG4 and JPEG triple compression to providing high quality images. Where H.264 and MPEG4 are standar[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 70 The device will be installed and work if a firewall exists on the network. If a firewall exists on the network, port 80 is open for ordinary data communication. The HTTP port and RTSP port need to be opened on the fi rewall or NAT router. The username and password for the fir[...]

5. Troubleshooting & FAQ 71  AirLive IP-200PHD User’s Manual • Maybe UPnP function of NA T router is not compatible to the IP camera. Please cont act your dealer to get the approval routers list. Some IP cameras are working but others are failed • Maybe too many IP cameras have been installed on the LAN, and then NAT router is out of r[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 72 • Packet Filtering of the rout er may prohibit access from an external network. Refer to your router's manual for details. • Access the Network Camera from the Internet with the global IP address of the r outer and port number of Network Camera. • Some routers reje[...]

5. Troubleshooting & FAQ 73  AirLive IP-200PHD User’s Manual settings prohibit downloading ActiveX controls”. The device work locally but not externally. • Might be caused from the fi rewall protection. Check the Internet firewall with your system or network administrator. The firewall may need to have some settings changed in order fo[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 74 Pan/Tilt does not work. (including Click to Center and Preset Positioning) • Click [Refresh] on the Internet Explorer when the communication stops with t he device. The image will refresh. • Other clients may be operating Pan/Tilt. • Pan/Tilt operation has r eached the [...]

5. Troubleshooting & FAQ 75  AirLive IP-200PHD User’s Manual 5.2 PING The PING (stands for Packet Internet Grope r) command is used to detect whether a specific IP address is accessible by sendi ng a packet to the specific address and waiting for a reply. It’s also a very useful tool to confir m the device installed or if the IP address [...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 76 5.3 Bandwidth Estimation The frame rate of video transmitt ed from the device depends on connection bandwidth between client and server, video reso lution, codec type, and quality setting of server. Here is a guideline to help you roughly estimate the bandwidth requirements f[...]

5. Troubleshooting & FAQ 77  AirLive IP-200PHD User’s Manual 5.4 Specification Table Camera IP-200PHD Image Device 2 Mega-pixel image sensor Effective Pixels 1600 x 1200 pixels Sensitivity 1.0V/lux-sec Signal to Noise 42.3dB Lens 4.3mm IP Module Video Video Encoder H.264, MPEG4 and Motion JPEG simultaneously (Tri-encoders) Video Profile 9 [...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 78 RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP Security Password protection, IP address filtering, HTTPS encrypted data transmission , user access log Users 20 simultaneous unicast users Ethernet 10/100M auto negotiation System Integration Application Programming Interface ONVIF O[...]

5. Troubleshooting & FAQ 79  AirLive IP-200PHD User’s Manual Cell Phone With 3GPP player Video Player VLC, Quick Time, Real Player, Core Player Software Search & Installation IPWizard II Bundled NVR Program SecuGuard 64CH 5.5 Configure Port Forwarding Manually The device can be used with a router. If t he device wants to be accessed fr[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 80 If you have cable or DSL service, you will most likely have a dynamically assigned WAN IP Address. ‘Dynamic’ me ans that your router’s WAN IP address can change from time to time depending on your ISP. A dynamic WAN IP Address identifies your router on the public networ[...]

5. Troubleshooting & FAQ 81  AirLive IP-200PHD User’s Manual accessible over the Internet. Th is is accomplished using the Virtual Server function on the router. The Virtual Server ports us ed by the camera must be opened through the router for remote access to your camera . Virtual Server is accessed by clicking on the Advanced tab of the[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 82 Enter valid ports in the Virtual Server section of your router. Please make sure to check the box on this line to enable setti ngs. Then the device can be access from WAN by the router’s WAN IP Address. By now, you have finished your entire PC configuration for this device.[...]

5. Troubleshooting & FAQ 83  AirLive IP-200PHD User’s Manual Host your own Networked Device and much more no matter what your computer's IP address may be and even if you have dialup, DSL or cable modem internet connection where your computer's IP address changes all the time!! DDNS service supports all top level domain nam es in[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 84 (3). After the columns show up at the left side, click “ Create Account”.[...]

5. Troubleshooting & FAQ 85  AirLive IP-200PHD User’s Manual (4). Fill the application agreem ent and necessary information. a. Username b. E-mail address and confirmation c. Password and confirmation d. Submit all the input informa tion and finish creating an account Click these two options[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 86 (5). Check your e-mail mailbox. There will be a n e-mail with a title “Your DynDNS Account Information“. Click the hyperlink address to confirm the DDNS service that you just applied. Then DDNS you applied activated. Click to confirm[...]

5. Troubleshooting & FAQ 87  AirLive IP-200PHD User’s Manual (6). Enter the web page http://www.dyndns.org/ again. Input your usern ame and password that you just applied to login administration interface of DDNS server. Input your account (7). If the correct username and passwor d are input, you can see the following picture at the top-ri[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 88 (10). Click the “ Get Started ”. (11). We could create a domai n name without any c harge at this step. First, we input the host name. (Pink No.1) Then we pick a domain that is easy to remember. (Pink No.2) The 3 rd step is to click “Offline Hostname” from Service Typ[...]

5. Troubleshooting & FAQ 89  AirLive IP-200PHD User’s Manual 4. Setup the DDNS and PPPoE of Netw orked Device At last, users have to enter the web page of Networked Device and setup the necessary information of DDNS and PPPoE a fter the application of DDNS service. Please check the user manual to access the DDNS and PPPoE pages. After savi[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 90 been officially changed to 230V, 240V is within tolerances and commonly found. Austria 230V 50 Hz Brazil 110/220V* 60 Hz *127V found in some states. Please check with your state electricity company. Canada 120V 60 Hz China, People's Republic of 220V 50 Hz Finland 230V 50[...]

5. Troubleshooting & FAQ 91  AirLive IP-200PHD User’s Manual 5.8 3GPP Table To use the 3GPP function, in addition to previous section, you might need more information or configuration to make this function work. Note that to use the 3GPP function, it stro ngly recommends to install the Networked Device with a public and fixed IP a ddress w[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 92 5.9 UPnP Use the following steps to enabl e UPnP settings only if your operating system of PC is running Windows XP. Go to Start > Settings . Click Control Panel Click Add or Remove Programs[...]

5. Troubleshooting & FAQ 93  AirLive IP-200PHD User’s Manual Click Add/Remove Windows Components The following screen will appear: Select Networking Services[...]

5. Troubleshooting & FAQ   AirLive IP-200PHD User’s Manual 94 Select Universal Plug and Play Click Details Click Next[...]

5. Troubleshooting & FAQ 95  AirLive IP-200PHD User’s Manual Please wait while Setup configures the components. Click Finish[...]