Aleratec 350103 manual

® USER GUIDE Aleratec 1:1 HDD Cruiser™ Part No. 350103[...]

www .aleratec.com Copyright/Model Identification The content of this manual is for informational purposes only and is subject to change without notice. This manual is copyright with all rights reserved. Under copyright laws, this manual and the software described within may not be copied, except in the normal use of the product(s) described within[...]

www .aleratec.com Radio/TV Interference Statement The equipment described in this guide emits radio frequency energy . If it is not installed in accordance with the manufacturer ’ s instructions, it may cause interference with radio or television reception. This equipment has been tested and found to comply with the limits for a Class B digital d[...]

www .aleratec.com Safety Regulations W ARNING T o prevent re or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to authorized personnel only .[...]

www .aleratec.com T able of Contents Introduction ................................................................................................... 1 Product Features ...................................................................................................1 Key Items ......................................................................[...]

www .aleratec.com ®[...]

www .aleratec.com 1 Introduction Thank you for purchasing the 1:1 HDD Cruiser . Please read this User Guide thoroughly before using this product. Product Features The 1:1 HDD Cruiser is a Hard Disk Drive Duplicator and Hard Disk Drive Sanitizer . • Sanitizes/W ipes drives clean with the choice of three Overwrite patterns: ▪ One Pass ▪ Three P[...]

www .aleratec.com 2 Introduction Key Items Display Panel (see page 4) Power Switch Controller Drive Bays (2) Source Drive T arget Drive[...]

www .aleratec.com 3 1 2 3 Introduction 1:1 HDD Cruiser Front Panel 1 Drive Bays Drive bays with quick loading doors. 2 Drive Bay Door The drive bay handle/tab is used to open the individual drive bays. 3 Drive LEDs Each HDD bay has a blue power light that will be on when there is an HDD properly inserted in the drive bay . Each HDD bay has an orang[...]

www .aleratec.com 4 Introduction 1:1 HDD Cruiser Copy Controller Display Panel and Buttons (Actual display may vary from illustration) 1. LCD display shows all functions and messages 2. ENT button is used to execute a selected function, or enter a menu 3. ESC button is used to cancel a selected function, or exit a menu 4. UP arrow is used to scroll[...]

www .aleratec.com 5 Precautions Before installing your 1:1 HDD Cruiser , please read the following. Installation A void placing the 1:1 HDD Cruiser in a location subject to: • High humidity • High temperature • Excessive dust • Mechanical vibration • Direct sunlight • Electromagnetic radiation Choose a Good Location 1. Allow adequate cl[...]

www .aleratec.com 6 Overview Power Up Sequence During the normal power-up sequence of the 1:1 HDD Cruiser , the following information will be displayed. • Figure 1 shows the rmware version • Figure 2 shows the memory initialization • Figure 3 shows the scanning of the drives • Figure 4 shows the number of drives loaded. • Figure 5 show[...]

www .aleratec.com 7 Overview Main Menu There are ten main menu items that can be seen in the 1:1 HDD Cruiser Copy Controller Display Panel. These are: 1. 2. 3. 4. 5. Note: The Advanced Setup function is a hidden menu. T o access this menu, press ESC for 3 seconds. After you have completed any desired adjustments, press ESC to exit Advanced Setup. E[...]

www .aleratec.com 8 Overview Subfunctions The “Setup” menu has nine (9) subfunctions. These are: 8-03 Startup Menu 8-04 Auto Compare 8-05 Copy with Size 8-06 Button Sound 8-07 Device Info 8-08 System Info 8-09 Fast Copy ENT ESC   8. Setup 8-01 Language 8-02 Copy Size[...]

www .aleratec.com 9 Overview The “Advanced Setup” menu has ten (10) subfunctions. These are: 10-01 Detect HDD Delay 10-02 Read Error Skip 10-03 Update Firmware 10-04 Compare Firmware 10-05 Quick Erase HDD 10-06 H/W Diagnostic 10-07 Load Default 10-08 Link Option 10-09 USB Auto Link 10-10 Copy HP A ENT ESC   10. Adv Setup (for USB Mode)[...]

www .aleratec.com 10 Using the 1:1 HDD Cruiser Loading the Hard Drives 1. Open the drive tray doors by lifting the tab on the left side of each drive bay you wish to use. 2. T ake the Hard Disc Drive (HDD) and align the drive’ s SA T A plug to the lower right hand side of the drive bay . 3. Slide the HDD into the drive bay until it stops. The dri[...]

www .aleratec.com 1 1 Using the 1:1 HDD Cruiser Removing Hard Drives 1. Open the drive tray doors by pulling the handle/tab on the left side of each drive tray door . Note: Do not attempt to remove the hard drive if the drive activity LED is on. 2. T o disengage the HDD, swing the drive tray door to the full open position. 3. Pull drive out toward [...]

www .aleratec.com 12 Using the 1:1 HDD Cruiser Main Menu Copy HDD The “Copy HDD” function performs an actual copy from a source HDD to one or more target HDDs. The target HDDs must be at least as large as the source. The 1:1 HDD Cruiser will copy every block of capacity on the source HDD. 1. Load the source HDD and the target HDDs into the 1:1 [...]

www .aleratec.com 13 Using the 1:1 HDD Cruiser 4. Once duplication is complete, a job status screen will be displayed. ENT ESC   1. Copy HDD OK:1 Fail: 0[...]

www .aleratec.com 14 Using the 1:1 HDD Cruiser Main Menu Compare HDD The “Compare HDD” function performs a comparison of data from the source hard drive to the data on the target hard drives. 1. With the source and tar get HDDs loaded use the arrow buttons (  or  ) to select “Compare HDD”. The following screen will be displayed. 2. Pr[...]

www .aleratec.com 15 Using the 1:1 HDD Cruiser Main Menu PreScan Source The “PreScan Source” scans the source hard drive to determine if it can be read correctly . 1. With the source HDD loaded, use the arrow buttons (  or  ) to select “PreScan Source”. The following screen will be displayed. 2. Press ENT to begin the scan. The system[...]

www .aleratec.com 16 Using the 1:1 HDD Cruiser Main Menu ReScan Bus The “ReScan Bus” function causes the 1:1 HDD Cruiser to redetect connected hard drives. This can be used when you change drives without restarting the system. 1. Use the arrow buttons (  or  ) to select “ReScan BUS”. The following screen will be displayed. 2. Press EN[...]

www .aleratec.com 17 Using the 1:1 HDD Cruiser Main Menu Source HDD Size The “Source size” function is used to display the capacity of the source hard drive. 1. With the source HDD loaded, use the arrow buttons (  or  ) to select “Source size”. The following screen will be displayed. 2. Press ENT to display the capacity of the sour[...]

www .aleratec.com 18 Using the 1:1 HDD Cruiser Main Menu Secure Erase The “Secure Erase” function will sanitize (wipe clean of all data) the hard disk drives connected to the 1:1 HDD Copy Cruiser using algorithms programmed by the hard drive manufacturer . Since this function is native to the hard drive, it is very fast and reliable. Almost all[...]

www .aleratec.com 19 ENT ESC   1 HDD CH:0 Wipe successful 5. Y ou can now scroll up and down for the individual status of each drive.[...]

www .aleratec.com 20 Using the 1:1 HDD Cruiser Main Menu Overwrite The “Overwrite” function will sanitize (wipe clean of all data) the hard disk drives connected to the 1:1 HDD Copy Cruiser . 1. Load the source HDD and the target HDDs into the 1:1 HDD Cruiser . The system will auto-detect the hard drives. Using the arrow buttons (  or  ) [...]

www .aleratec.com 21 Using the 1:1 HDD Cruiser b. T o perform a “Three Pass Overwrite”, scroll to “3 Pass” and press ENT . This method will write one pass of 1’ s, one pass of zeros, and one pass of randomly generated data. The next screen allows you to choose whether you wish to verify the random overwrite. Use the arrow buttons to toggl[...]

www .aleratec.com 22 Using the 1:1 HDD Cruiser Main Menu Setup The “Setup” menu contains conguration options for the 1:1 HDD Copy Cruiser . It is suggested to use the factory defaults for optimum performance. 1. Use the arrow buttons (  or  ) to select “Setup”. Press ENT to select. The following screen will be displayed. Note: Afte[...]

www .aleratec.com 23 Using the 1:1 HDD Cruiser Setup Menu 8-01 Language This option allows you to select the language that is used for the display . 1. Use the arrow buttons (  or  ) select “Setup”. The following screen will be displayed. 2. U se the arrow buttons (  ) to scroll to “Language”. The following screen will be displa[...]

www .aleratec.com 24 Using the 1:1 HDD Cruiser Setup Menu 8-02 Copy Size This function is used to specify the amount of source disk data to copy to the target drives. 1. Use the arrow buttons (  or  ) select “Setup”, then press ENT . The following screen will be displayed. 2. U se the arrow buttons (  ) to scroll to “Copy Size”.[...]

www .aleratec.com 25 Using the 1:1 HDD Cruiser Setup Menu 8-03 Startup Menu This option lets you select any of the functions (except “Setup”) as the initial function that appears when the 1:1 HDD Cruiser is powered on. 1. Use the arrow buttons (  or  ) select “Setup”. The following screen will be displayed. 2. U se the arrow buttons ([...]

www .aleratec.com 26 Using the 1:1 HDD Cruiser Setup Menu 8-04 Auto Compare This option allows you to choose whether or not to automatically compare the source and target hard drives after every copy operation. 1. Use the arrow buttons (  or  ) select “Setup”. The following screen will be displayed. 2. U se the arrow buttons (  ) to[...]

www .aleratec.com 27 Using the 1:1 HDD Cruiser Setup Menu 8-05 Copy with Size This option allows you to choose whether or not to automatically rescan for connected drives immediately before a copy operation. 1. Use the arrow buttons (  or  ) select “Setup”. The following screen will be displayed. 2. U se the arrow buttons (  ) to sc[...]

www .aleratec.com 28 Using the 1:1 HDD Cruiser Setup Menu 8-06 Button Sound This option allows you to enable or disable the beeping sound heard when you press a button. 1. Use the arrow buttons (  or  ) select “Setup”. The following screen will be displayed. 2. U se the arrow buttons (  ) to scroll to “Button Sound”. The followi[...]

www .aleratec.com 29 Using the 1:1 HDD Cruiser Setup Menu 8-07 Device Info This option displays information about any hard drives connected to the 1:1 HDD Cruiser . 1. Use the arrow buttons (  or  ) to scroll to “Setup”. The following screen will be displayed. 2. U se the arrow buttons (  ) to scroll to “Device Info”. The follow[...]

www .aleratec.com 30 Using the 1:1 HDD Cruiser Setup Menu 8-08 System Info This function displays information about the 1:1 HDD Cruiser , including the current rmware version. 1. Use the arrow buttons (  or  ) to select “Setup”. The following screen will be displayed. 2. After selecting “Setup” use the arrow keys (  ) to togg[...]

www .aleratec.com 31 Using the 1:1 HDD Copy Cruiser Setup Menu 8-09 Fast Copy The “Fast Copy” option allows you to choose whether to copy the entire source hard disk, or only the used space. 1. Press the arrow buttons (  ) to scroll to “Fast Copy”. The following screen will be displayed. 2. Press ENT to display the current congurat[...]

www .aleratec.com 32 Using the 1:1 HDD Cruiser Main Menu USB Mode This option connects the HDDs in the drive bays to a PC via the USB port on the back of the 1:1 HDD Cruiser . 1. Use the arrow buttons (  or  ) to select “USB Mode”. The following screen will be displayed. 2. Press ENT and the following screen will be displayed. 3. Use the [...]

www .aleratec.com 33 Using the 1:1 HDD Cruiser Main Menu USB Mode - continued 5. Press ENT and the following screen will be displayed. Use the down arrow key (  ) to select “YES” to return to stand-alone mode. The controller will prompt you to restart the device. ENT ESC   Back to SA Mode? NO ENT ESC   Please W ait ...[...]

www .aleratec.com 34 Using the 1:1 HDD Cruiser Advanced Setup Menu The “Adv Setup” menu contains additional conguration options for the 1:1 HDD Cruiser . 1. Press and hold the ESC button for 3 seconds to enter Adv Setup. The following screen will be displayed. Note: After changing any of the configuration options, you must press ENT to a[...]

www .aleratec.com 35 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-01 Detect HDD Delay This function is used to set the time interval between the system’ s re-scans of all connected HDD devices. 1. Press and hold ESC for about 3 seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use the arrow buttons (  o[...]

www .aleratec.com 36 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-02 Read Error Skip This function can be enabled to ignore any error that occurs during copying. By default, the 1:1 HDD Cruiser will halt the copy operation when it encounters an unreadable area of the source hard disk and display an error . Enabling this option will ignore any b[...]

www .aleratec.com 37 Using the 1:1 HDD Copy Cruiser Advanced Setup Menu 10-03 Update Firmware This function is used to update the 1:1 HDD Copy Cruiser rmware to a later version. Note: Firmware updates are available from Aleratec technical support. 1.a CD method Open the case of the 1:1 HDD Copy Cruiser . Disconnect the SA T A cable from the blue[...]

www .aleratec.com 38 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-04 Compare Firmware This function is used to compare the rmware version currently installed with one on a DVD/CD disc. Note: Use “Compare Firmware” after updating the firmware from e-mail or from the Aleratec web site. This function is used after performing a firmware up[...]

www .aleratec.com 39 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-05 Quick Erase HDD This function is used to erase the data of a hard drive quickly . W arning : Backup any important data before using this function. 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use t[...]

www .aleratec.com 40 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-06 H/W Diagnostic This function is used to test various components of the 1:1 HDD Cruiser . 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use the arrow buttons (  or  ) to select “H/W Diagnosti[...]

www .aleratec.com 41 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-07 Load Default This function is used to restore all factory settings of the 1:1 HDD Cruiser back to their original defaults. 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use the arrow buttons (  o[...]

www .aleratec.com 42 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-08 Link Option (for USB mode) This function is used to decided if “9.USB Mode” will be displayed in the display panel. 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use the arrow buttons (  or ?[...]

www .aleratec.com 43 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-09 USB Auto-Link This function sets the 1:1 HDD Cruiser to immediately enter USB mode on startup. This allows direct control of the unit from a PC. 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. Use the[...]

www .aleratec.com 44 Using the 1:1 HDD Cruiser Advanced Setup Menu 10-10 Copy HP A If the source hard disk contains a Host Protected Area (HP A), this option allows you to choose whether or not to copy data within the HP A. 1. Press and hold ESC for about three seconds to access the “Adv Setup” menu. The following screen will be displayed. 2. U[...]

www .aleratec.com 45 Specifications Power Requirements 1 15 - 230 V AC Switchable Dimensions (depth x width x height) D: 285.8mm W : 187.3mm H: 171.5mm (7.38” x 6.75” x 1 1.25”) W eight 3.36 Kilograms (7.4 Lbs.) Note: Specifications subject to change without notice. T roubleshooting If your 1:1 HDD Cruiser is not performing as expected, ref[...]

www .aleratec.com 46 T echnical Support After reading this User Guide, if you need additional assistance with this product, please contact Aleratec T echnical Support. Our technical staff will be happy to assist you, but they may need your help to better assist you. Contacting support without all the necessary information can be both time consuming[...]

www .aleratec.com 47 Service and Support Aleratec, Inc., Limited Warranty This Limited W arranty covers defects encountered in the course of normal use of this product and does not apply to damage from improper use, abuse, accidents, unauthorized service, or inadequate packaging when shipping the product to Aleratec, Inc. Aleratec, Inc. provides th[...]

www .aleratec.com 48 Service and Support Please Note: This W arranty is valid only within the United States and Puerto Rico, and applies only to products that are new and unopened on the date of purchase. For areas outside the United States and Puerto Rico, contact the authorized dealer from whom you purchased this product to determine which warran[...]

www .aleratec.com 49 Service and Support T o Obtain Warranty Service: Y ou must ship your subsystem to the authorized dealer where your subsystem was purchased within the one year warranty period and no later than thirty days after discovery of claimed defect, whichever occurs rst. In either case, you must provide proof of original purchase befo[...]

www .aleratec.com 50 T echnical Support F AX Back Form Aleratec, Inc. T echnical Support Fax Back Form Please record the following information to help expedite any warranty claim: Model No.: _________________ Serial No.: _______________________________ Date Purchased: ______________________________________________________ Place of Purchase: _______[...]

www .aleratec.com Notes:[...]

Document Number: 9399058_ENG_Rev . I Copyright © 2010 Specifications subject to change without notice. Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A. www .aleratec.com[...]