American Water Heater 1010 319869-000 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones American Water Heater 1010 319869-000. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica American Water Heater 1010 319869-000 o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual American Water Heater 1010 319869-000 se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales American Water Heater 1010 319869-000, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones American Water Heater 1010 319869-000 debe contener:
- información acerca de las especificaciones técnicas del dispositivo American Water Heater 1010 319869-000
- nombre de fabricante y año de fabricación del dispositivo American Water Heater 1010 319869-000
- condiciones de uso, configuración y mantenimiento del dispositivo American Water Heater 1010 319869-000
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de American Water Heater 1010 319869-000 no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de American Water Heater 1010 319869-000 y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico American Water Heater en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de American Water Heater 1010 319869-000, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo American Water Heater 1010 319869-000, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual American Water Heater 1010 319869-000. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    Installation and Operating Manual 1010 319869-000 KEEP THIS MANUAL IN THE POCKET ON HEA TER FOR FUTURE REFERENCE WHENEVER MAINTENANCE ADJUSTMENT OR SERVICE IS REQUIRED. POWER VENT GAS MODELS ALL TECHNICAL AND W ARRANTY QUESTIONS: SHOULD BE DIRECTED T O THE LOCAL DEALER FROM WHOM THE W A TER HEA TER W AS PURCHASED. HYBRID GAS W A TER HEA TERS • Fo[...]

  • Página 2

    2 www .americanwaterheater .com T ABLE OF CONTENTS SAFE INST ALLA TION, USE AND SERVICE 3 GENERAL SAFETY 4 INTRODUCTION 6 Get T o Know Y our Water Heater - Gas Models . . . . . 8 Replacement Parts And Deliming Products . . . . . . . 8 INST ALLA TION CONSIDERA TIONS 9 Rough In Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 9 W ater Pipin[...]

  • Página 3

    www .americanwaterheater .com 3 Y our safety and the safety of others is extremely important in the installation, use and servicing of this water heater . Many safety-related messages and instructions have been provided in this manual and on your own water heater to warn you and others of a potential injury hazard. Read and obey all safety messages[...]

  • Página 4

    4 www .americanwaterheater .com GENERAL SAFETY[...]

  • Página 5

    www .americanwaterheater .com 5 GENERAL SAFETY Breathing carbon monoxide can cause brain damage or death. Always read and understand instruction manual. • Install vent system In accordance with codes. • Do not operate water heater if flood damaged. • Special Consideration must be taken with installations above 1 1,000' (3,352m) for stand[...]

  • Página 6

    6 www .americanwaterheater .com Thank Y ou for purchasing this water heater . Properly installed and maintained, it should give you years of trouble free service. Abbreviations Found In This Instruction Manual: • CSA - Canadian Standards Association • ANSI - American National Standards Institute • NFP A - National Fire Protection Association [...]

  • Página 7

    www .americanwaterheater .com 7[...]

  • Página 8

    8 www .americanwaterheater .com FIGURE 1 GET TO KNOW YOUR W A TER HEA TER - GAS MODELS REPLACEMENT PARTS AND DELIMING PRODUCTS Replacement parts and recommended delimer may be ordered through authorized servicers or distributors. When ordering parts, provide complete model and serial numbers (see rating plate), quantity and name of part desired. St[...]

  • Página 9

    www .americanwaterheater .com 9 Capacity , Gas and Electrical Characteristics Model Approx. Capacity Input Ga s Ty p e Gas Supply Pressure Manifold Pressure Electrical Characteristics U.S. Gals. Litres BTU/hr Max. in. WC (kPa) Min. in. WC (kPa) in. WC (kPa) V olts/Hz Amperes GH-90N 25 94.6 100,000 Nat. 14.0 (3.49) 5.0 (1.25) 4.2 (1.05) 120/60 2. 5 [...]

  • Página 10

    10 www .americanwaterheater .com For all side wall terminated, horizontally vented power vent, gas fueled water heaters installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) fe[...]

  • Página 11

    www .americanwaterheater .com 1 1 FIGURE 3 W A TER PIPING - MIXING V AL VE USAGE This appliance has been design certi fi ed as complying with ANSI Z21.10.3/CSA 4.3 (latest revision) for water heaters and is considered suitable for: W ater (Potable) Heating: All models are considered suitable for water (potable) heating. The Hybrid water heater is [...]

  • Página 12

    12 www .americanwaterheater .com and the physically or developmentally disabled. If anyone using hot water from this heater fi ts into one of these groups or if there is a local code or state law requiring a certain temperature water at the hot water tap, then you must take special precautions. In addition to using the lowest possible temperature [...]

  • Página 13

    www .americanwaterheater .com 13 Also, the water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle. HANDLE INST ALLA TION For ease of handling and carrying, plugs are provided in the side of the shroud that can be removed and pipe handles inserted (see Figure 4). • Remove plastic plugs from shroud[...]

  • Página 14

    14 www .americanwaterheater .com When installing the heater , consideration must be given to proper location. Location selected should be as close to the wall as practicable and as centralized with the water piping system as possible. FIGURE 5 Minimum clearances between the water heater and combustible construction are 0 in. at the sides and rear ,[...]

  • Página 15

    www .americanwaterheater .com 15 Screws Screws To p Casing (Front) FIGURE 7 Screws FIGURE 8 FIGURE 9 After the heater has been positioned and the earthquake straps have been installed, re-assemble the shroud in the reverse order .[...]

  • Página 16

    16 www .americanwaterheater .com COMBUSTION AIR AND VENTILA TION A gas water heater cannot operate properly without the correct amount of air for combustion. Do not install in a con fi ned area such as a closet, unless you provide air as shown in the “Facts to Consider About Location” section. Never obstruct the fl ow of ventilation air . If [...]

  • Página 17

    www .americanwaterheater .com 17 FIGURE 1 1 B. ALL AIR FROM OUTDOORS: (See Figures 12, 13 and 14) The con fi ned space should be provided with two permanent openings, one commencing within 12 in. (30cm) of the top and one commencing within 12 in. (30cm) from the bottom of the enclosure. The openings should communicate directly , or by ducts, with [...]

  • Página 18

    18 www .americanwaterheater .com 6 . Louvers and Grilles: In calculating free area, consideration should be given to the blocking effect of louvers, grilles or screens protecting openings. Screens used should not be smaller than 1/4 in. (0.64cm) mesh. If the free area through a design of louver or grille is known, it should be used in calculating t[...]

  • Página 19

    www .americanwaterheater .com 19 limited warranty . Thermal expansion can also cause intermittent temperature-pressure relief valve operation: water discharged from the valve due to excessive pressure build up. The temperature-pressure relief valve is not intended for the constant relief of thermal expansion. This condition is not covered under the[...]

  • Página 20

    20 www .americanwaterheater .com The temperature-pressure relief valve must be installed directly into the fi tting of the water heater designed for the relief valve. Must terminate a maximum of 6 in. (15cm) above a fl oor drain or external to the building. In cold climates, it is recommended that the discharge pipe be terminated at an adequate d[...]

  • Página 21

    www .americanwaterheater .com 21 GAS PIPING Make sure gas supplied is same type listed on model rating plate. The inlet gas pressure must not exceed 14 in. WC (3.5 kPa) for natural and propane gas (L.P .). The minimum inlet gas pressure shown on rating plate is that which will permit fi ring at rated input. All gas piping must comply with local co[...]

  • Página 22

    22 www .americanwaterheater .com a sediment trap) must be incorporated in the piping. The drip leg must be readily accessible. Install in accordance with the “Gas Piping” section. Refer to the current edition of the National Fuel Gas Code (ANSI Z223.1/NFP A 54). GAS LINE PURGING Air may be present in the gas lines and could prevent the burner f[...]

  • Página 23

    www .americanwaterheater .com 23 VENT PIPE TERMINA TION STREET ELBOW NORMAL ELBOW PREFERRED PRACTICE: 90° LONG SWEEP ELBOW (LESS RESTRICTIVE) BACK T O BACK ELBOWS 90° SHORT SWEEP ELBOW (MORE RESTRICTIVE) 6 in. (15 cm) min. NOT RECOMMENDED: FIGURE 19 VENT LENGTH LESS THAN OR EQUAL TO 20 EQUIV ALENT FEET (6.1m) USE THIS SCREEN. VENT LENGTH GREA TER[...]

  • Página 24

    24 www .americanwaterheater .com V ent piping must slope up from heater to termination a minimum of 1/8 in. (0.3cm) rise per 4 ft. (1.2m) of vent piping TERMINA TION ELBOW RODENT SCREEN (INST ALL INT O ELBOW) GROUND LEVEL OR MAXIMUM SNOW LINE* STRAP 6 in. (15cm) MIN. 90° ELBOW Example for calculating equivalent feet. Section “A” . . . . 0.5 ft[...]

  • Página 25

    www .americanwaterheater .com 25 CONDENSA TE This water heater is a condensing unit and requires a drain to be located in close proximity to allow the condensate to drain safely . The condensate drains from the unit at the exhaust tee located at the bottom of the unit (see Figure 22). Condensate from this water heater is mildly acidic. Please note [...]

  • Página 26

    26 www .americanwaterheater .com SEQUENCE OF INST ALLA TIONS Cut a length of PVC pipe about 3.5 in. (9cm) longer than the wall thickness at the opening. Glue the vent terminal to this section of pipe. Slide the wall plate over the pipe to stop against the vent terminal. Place a bead of caulking (not supplied) around the gap between the pipe and cov[...]

  • Página 27

    www .americanwaterheater .com 27 VENT PIPING TO BE SLOPED (DOWN) TOW ARD HEA TER TO PREVENT WA TER FROM COLLECTING. 6 in. (15 cm) MIN. LENGTH A TT ACH 45° TERMINA TION ELBOW RODENT SCREEN (INST ALL INTO ELBOW) SEALANT 12 in. (30 cm) min. * WHERE SNOW COVER IS NORMAL DURING WINTER, ENSURE SUFFICIENT VENT CLEARANCE TO PREVENT BLOCKAGE OR ICE BUILDUP[...]

  • Página 28

    28 www .americanwaterheater .com FIGURE 28 A VENT USED IN A SPECIAL VENTING SYSTEM WITH POSITIVE VENT PRESSURE AND P ASSING THROUGH A ROOF SHALL EXTEND A T LEAST 450mm (18 in.) ABOVE THE HIGHEST POINT WHERE IT P ASSES THROUGH THE ROOF SURF ACE AND ANY OTHER OBSTRUCTION WITHIN A HORIZONT AL DIST ANCE OF 450mm (18 in.). A VERTICAL VENTING SYSTEM MUST[...]

  • Página 29

    www .americanwaterheater .com 29 PRIMER It is recommended that T etrahydrofuran (THF) be used to prepare the surfaces of pipe and fi ttings for solvent welding. Do not use water , rags, gasoline or any other substitutes for cleaning PVC or CPVC surfaces. A chemical cleaner such as MEK may be used. CEMENT The cement should be a bodied cement of app[...]

  • Página 30

    30 www .americanwaterheater .com D. Inspection, cleaning, priming Visually inspect the inside of the pipe and fi tting sockets and remove all dirt, grease or moisture with a clean dry rag. If wiping fails to clean the surfaces, a chemical cleaner must be used. Check for possible damage such as splits or cracks and replace if necessary . Depth-of-e[...]

  • Página 31

    www .americanwaterheater .com 31 U.S. POWER VENT W ARNING VENT HOOD(S) MA Y BE EXTREMEL Y HOT DURING OPERA TION. FIGURE 31 CAUTION TO PREVENT EXHAUSTING PRODUCTS FROM CIRCULA TING TO THE AIR INT AKE IN WINDY/COLD AREAS, THE MAXIMUM PRACTICAL DIST ANCE BETWEEN THESE TWO TERMINALS IS RECOMMENDED.[...]

  • Página 32

    32 www .americanwaterheater .com ELECTRICAL CONNECTIONS The water heater must be connected to a properly grounded electrical branch circuit. A dedicated circuit is preferred. Do not use a GFI outlet. Refer to the rating plate attached to the water heater to determine the electrical requirements for the heater . Ensure the circuit provided is correc[...]

  • Página 33

    www .americanwaterheater .com 33 OPERA TING INSTRUCTIONS Changing the Standby Status When the Standby Button is pressed, the Status changes to normal operation and all the LEDs on the display will light up for a period of 1 second to verify operation. The button can toggle the status between Normal operation and Standby . Key Lock NOTE: This is a t[...]

  • Página 34

    34 www .americanwaterheater .com Numeric Display Numeric information such as temperature set-point, maintenance codes and error codes are displayed using a large yellow LED display . Up and Down Buttons T wo buttons (with “Up” and “Down” arrows) are used for adjusting the data on the display . Other secondary functions such as turning the K[...]

  • Página 35

    www .americanwaterheater .com 35 WIRING DIAGRAM Obey local codes and electric utility requirements when you install or service the water heater . This appliance must be electrically grounded in accordance with local codes or , in the absence of local codes, with the National Code ANSI/NFPA No 70 (current edition) and/or the CSA C22.1 electrical Cod[...]

  • Página 36

    36 www .americanwaterheater .com LIGHTING INSTRUCTIONS 1 . S et the ther most at to the lowest set ting. 2. Set th e ON/O FF switch o n the c ontrol pane l to the “O FF” position. 3. T urn of f all electric al power to the appliance if ser vice is to be per forme d. T O TURN OFF GAS T O APPLIANCE 1. STOP! Read the sa fety info rmati on above on[...]

  • Página 37

    www .americanwaterheater .com 37 HEA T CYCLE DEFINITIONS ST A TE DESCRIPTION Pre-purge If the heat engine initial call-for-heat is successful (all checks are passed), the combustion fan is energized. The fan is started at a high speed for several seconds and the system veri fi es the fan speed. Input signals (from other parts of the water heater) [...]

  • Página 38

    38 www .americanwaterheater .com TEMPERA TURE REGULA TION FIGURE 35 It is recommended that lower water temperatures be used to avoid the risk of scalding. It is further recommended, in all cases, that the water temperatures be set for the lowest temperature which satis fi es your hot water needs. This will also provide the most energy ef fi cient[...]

  • Página 39

    www .americanwaterheater .com 39 W ater T emperature T ime for 1st Degree Burn (Less Severe Burns) T ime for Permanent Burns 2nd & 3rd Degree (Most Severe Burns) 1 10°F (44°C) (normal shower temp.) 1 16°F (47°C) (pain threshold) 1 16°F (47°C) 35 minutes 45 minutes 122°F (50°C) 1 minute 5 minutes 131°F (55°C) 5 seconds 25 seconds 140°[...]

  • Página 40

    40 www .americanwaterheater .com W ater Circulation Pump A circulation pump is integrated into the heat engine for the Hybrid application. The pump serves to push water through the heat engine at a rate that supports optimum recovery time and maximum heat output. The control provides 120V ac, 60Hz line power to the pump to enable operation. W ater [...]

  • Página 41

    www .americanwaterheater .com 41 Line V oltage Monitor The control monitors the line voltage provided to the system. If the line voltage is too low , the system components may not operate properly . For diagnostic purposes, the display panel should indicate that the cause was power-related. • If line power is below 102V ac, the water heater will [...]

  • Página 42

    42 www .americanwaterheater .com CONST ANT OUTPUT TEMPERA TURE CONTROL While the temperature regulation in the previous section describes the features of temperature monitoring and regulation, your water heater goes beyond the on/off control implied there and implements a gas, air and water fl ow modulation scheme to provide a constant water deliv[...]

  • Página 43

    www .americanwaterheater .com 43 HOUSEKEEPING V acuum around base of water heater for dust, dirt, and lint on a regular basis. VENTING SYSTEM INSPECTION At least once a year a visual inspection should be made of the venting system. Y ou should look for: Obstructions which could cause improper venting. The combustion and ventilation air fl ow must [...]

  • Página 44

    44 www .americanwaterheater .com softened water is exceedingly corrosive because the process substitutes sodium ions for magnesium and calcium ions. The use of a water softener may decrease the life of the water heater tank. The anode rod should be inspected after 3 years of use and annually thereafter until the condition of the anode rod dictates [...]

  • Página 45

    www .americanwaterheater .com 45 SNOW ACCUMULA TION Keep the area around fl ue terminal free of snow and ice. The appliance will not function properly if the intake air or exhaust is impeded (blocked or partially blocked) by obstructions. CLEANING THE INLET W A TER FIL TER The cold water inlet fi lter must be cleaned on a regular basis. The frequ[...]

  • Página 46

    46 www .americanwaterheater .com • Disconnect the hoses joining the tank and the heat engine (upper hose is water outlet and lower hose is water inlet). • Connect addition length of hose (not provided) to existing hoses. (Note: The heat engine hose is a 3/4” NPT thread which is dif ferent for a garden hose thread.) 5 gallon pail of virgin, fo[...]

  • Página 47

    www .americanwaterheater .com 47 DIAGNOSTIC DISPLA Y By simultaneously pressing the “Mode” and “down arrow” buttons for 3 seconds the unit will allow access to the diagnostic mode. In diagnostic mode, using the up/down arrow allows for cycling between diagnostic codes. The numeric display will show the diagnostic code for 1 second, followed[...]

  • Página 48

    48 www .americanwaterheater .com If an error code is displayed, or odd behavior of the unit occurs, the fi rst corrective action should be to “Cycle the Power”: Unplug the 120V ac power cord and after 5 seconds plug it in again. If this doesn’t clear the fault, proceed with the “Remedy” in the following table (T able 5). If wire harness [...]

  • Página 49

    www .americanwaterheater .com 49 Fault Code Displayed Description Cause Lockout type Remedy E15 Blower speed abnormal. Blower speed is 200RPM below the target speed for 20 seconds. Soft Check the blower wire harness. Change the blower . Change the board. 1. 2. 3. E16 Blower speed is 500RPM above the target speed for 6 seconds. E17 Machine starts or[...]

  • Página 50

    50 www .americanwaterheater .com Fault Code Displayed Description Cause Lockout type Remedy E33 W ater Flow V alve Closed. The water valve did not open when attempting to establish fl ow . Soft Check the water valve wire harness. Change the board. Change the water valve. 1. 2. 3. E34 Proportional V alve (PV) Response T oo Slow . The closed loop co[...]

  • Página 51

    www .americanwaterheater .com 51 These guidelines should be utilized by a quali fi ed service agent. Problem Possible Cause(s) What to do NOT ENOUGH HOT WA TER ST ANDBY button turned of f. Press switch to turn heater on. No power at outlet. Repair service to outlet. Error Code being displayed Refer to “F AUL T INDICA TION AND ERROR CODES” sect[...]

  • Página 52

    52 www .americanwaterheater .com Problem Possible Cause(s) What to do WHEN THE T AP IS OPENED, THERE IS NO HOT W A TER OR THE HOT W A TER TURNS COLD AND ST A YS COLD. a. The hot water fi xture is not suf fi ciently open to draw the water through the heater . b. The unit display is an error code. c. There is an external recirculation system instal[...]

  • Página 53

    www .americanwaterheater .com 53 SERVICE If a condition persists or you are uncertain about the operation of the water heater contact a quali fi ed service agency . LEAKAGE CHECKPOINTS Use this guide to check a “Leaking” water heater . Many suspected “Leakers” are not leaking tanks. Often the source of the water can be found and corrected.[...]

  • Página 54

    54 www .americanwaterheater .com P ARTS IDENTIFICA TION ITEM # DESCRIPTION A Baf fl e, Flue B Hot Water Outlet Nipple (w/ Anode, Heat T rap) C T&P Relief V alve D Cold W ater Inlet Nipple (w/ Dip T ube, Heat T rap) E Cover , Back-Flue Gas Return F T op Insulation G Flue Gas Return Duct Assy H Shroud, Back-T ank Assembly I Shroud, Right Side-T [...]

  • Página 55

    www .americanwaterheater .com 55 R O NM L K J I H G F E D C B A T Q S P 12 U 10 7 6 5 4 3 2 1 Z Y X W V 11 9 8 13[...]

  • Página 56

    56 www .americanwaterheater .com REPLACEMENT P ARTS DESCRIPTION KIT # Drain valve 9000058015 T&P relief valve 9003741005 Anode/MG/NIP/HT 9004333005 Anode/AL/NIP/HT 9006291005 Circulation pump assembly 9007173005 Inlet/outlet thermistor (T emp sensor) 9007174005 PCB assembly w/ base 9007175005 12” Hose (braided) 9007176005 T ank thermistor 900[...]

  • Página 57

    www .americanwaterheater .com 57 LIMITED RESIDENTIAL GAS W ARRANTY THIS W ARRANTY IS APPLICABLE T O THE ORIGINAL OWNER ONL Y If the glass lined tank in this water heater shall prove upon examination by (the warrantor) to have leaked during the warranty period in normal residential use, due to natural corrosion from potable water therein, the warran[...]

  • Página 58

    58 www .americanwaterheater .com NOTES[...]

  • Página 59

    www .americanwaterheater .com 59 NOTES[...]

  • Página 60

    Copyright © 2010 American Water Heater Company . All rights reserved.[...]