AMX Modero MVP-8400i manual

Operation/Reference Guide Touch Panels MVP-8400i 8.4" Modero ® ViewPoint ® Touch Panel with Intercom Last Revised: 4/1/2011[...]

AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity . AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) ye a[...]

AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software. The AMX Software consists of general[...]

FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the fol lowing two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding in terference that may cause undesi red operation. Federal Communications Commission (FCC) Statement T[...]

Table of Contents i MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom Table of Contents MVP-8400i Modero Viewpoint Wireless To uch Panel With I ntercom ................. 1 Overview .............................. ......................... ................... .................... .................... 1 Specifications .............. [...]

ii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Step 3: Choose a Master Connection Mode ........ ................... ......................... ....... 27 USB........... ............. ................. ............. ............. ................ ............. ............. ............... .... 27 Prepare you[...]

Table of Contents iii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom EAP-TLS Settings ........ ............. ............. ................ ............. ............. ................ ............. .. 79 Client certifi cate config uration ......... ................ ............. ............. ................. ............. ..[...]

iv MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Overview ........... ......................... .................... ................... .................... ............... 107 Button Assignments .............. ......................... ................... .................... ............... 107 Page Comman[...]

Table of Contents v MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom ^BNP ......... ............... ............ ............ ........... ............... ............ ............ ........... ............ .. ............ 127 ^BNT ............ ............ ............ ............ .............. ............ ............ ........[...]

vi MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents ^UNI ............... ........... ............ ............ ............... ........... ............ ............ ............ ........... ............ 139 ^VTP ............... ........... ............ ............ ............... ........... ............ ......[...]

Table of Contents vii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom PKEYP ............. ............ ............ ............... ........... ............ ............ ............... ........... ......... ... ........ 156 @PKP ............ ............ ............ ............... ........... ............ ............ .......[...]

viii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents ^RSR ............... ........... ............ ............... ............ ........... ............ ............... ............ ........ ... ......... 166 Escape Sequences .............. ................. ............. ............ ................. ........[...]

Table of Contents ix MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom ^PHN-SETUP-PROXYADDR ........ ............ ........... ............... ............ ............ ........... ............... ..... 173 ^PHN-REDIAL ..... ............... ............ ........... ............... ............ ............ ............ ............[...]

x MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Only One Mode ro Panel in My System Shows U p .................. ............. ................ ........ 196 Panel Behaves S trangely After Downloa ding a Panel F ile or Firmware ............ ........... 19 6 Panel Fails to Charge in MVP-W DS .................. [...]

MVP-8400i Modero Viewpoint Wireless Touch Panel With Int ercom 1 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Modero Viewpoint Wireless Touch Panel With Intercom Overview The MVP-8400i Modero V iewpoint W ireless T ouch Panel ( FIG. 1 ) is a 8.4", 802.11-based wireless handheld G4 touch panels, p re-installed wi[...]

MVP-8400i Modero Viewpoint Wireless Touch Panel With Interco m 2 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Optional AMX accessory solutions for the MVPs include  MVP-TDS T able T op Dockin g Station (see the MVP-TDS T able T op Docking Station Operation/Refer ence Guide for details).  MVP-WDS W all/Flush Mount D[...]

MVP-8400i Modero Viewpoint Wireless Touch Panel With Int ercom 3 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Specifications (FG 5965-04) (Cont.) Power Modes: • ON: Panel is fully functional. • ST AN DBY : Panel uses low power, the L CD/backlight is shut down, LEDs still function. Panel resumes the ON mode in ~ 1[...]

MVP-8400i Modero Viewpoint Wireless Touch Panel With Interco m 4 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Specifications (FG 5965-04) (Cont.) Internal Components (Cont.): Button Assignments: Button assignments can only be adjusted in TPD4 and not on the panels. • Button channel range: 1 - 4000 button push and f[...]

MVP-BP Power Pack 5 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-BP Power Pack Overview The MVP-BP Po wer Pack ( FG5965-20 ) is a rechargeable Lithium-Ion ba ttery used to provide power to the MVP touch panels. T wo MVP-BPs are included with each MVP-8400i touch panel. MVP-BPs can be charged with either a T able T op Docki[...]

MVP-BP Power Pack 6 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 4. T o replace the battery compartme nt cov er , use the alignment guide holes to align the cov er with the edges of the battery compartment, and slid e it back i nto place until it snaps shut. FIG. 4 Installing MVP-BP ba tteries into the MVP battery slots Batter[...]

NXA-CFSP Compact Flash 7 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom NXA-CFSP Compact Flash Overview Every MVP panel is shipped with a 128 MB Compact Flash c ard. Compact Flash Card - Security All security user names and passwords (for the docki ng station) are stored in the Co mpact Flash card. After installing the Compact F[...]

NXA-CFSP Compact Flash 8 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. Grasp the bottom rim of the rear housing just above the MVP interface connector , and carefully pull the bottom rim aw ay from the IR Emitter and up, to e xpose the internal components. 4. Remov e the trim from the top rim of the circuit board ( FIG. 5 ).[...]

NXA-CFSP Compact Flash 9 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 2. Place the circuit board on a flat le vel surf ace so that the IR Emitters are pointing aw ay from you ( FIG. 6 ). 3. Insert the tip of a grounded flat-head scre wdriv er into one of the card removal groo ves (located on either side of the existing Compact[...]

NXA-CFSP Compact Flash 10 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Panel Calibration 11 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Calibration This section outlines the steps for calibrating the touch panel. It is r ecomme nded that you calibrate the panel both befor e its initial use and after completing a f irmwar e download. Modero panels are factory setup with specific demo touch [...]

Panel Calibration 12 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. After the " Calibration Successful. " message appears, press anywhere on the screen to continue and return to the Setup page. Testing your Calibration 1. Press the Calibrate butt on on the to enter the Calibrate page ( FIG. 10 ). 2. Press anywhere o[...]

Configuring Communications 13 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring Communications Communication between the MVP and the Master consists of using either W ireless Ethernet (DHCP , Static IP) or USB. References to Ethernet in this manual focus on the use of W ireless Ethernet via the MVP’ s WiFi Card. Moder[...]

Configuring Communications 14 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the Panel’ s Device Number In the Pr otec ted Setup page: 1. Press the De vice Number field to open the De vice Number keypad ( FIG. 12 ). Enter a unique Device Number assignment for the panel , and press Done to return to the Pr otected Setup[...]

Configuring Communications 15 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring a Wireless Network Access When working with a wireless card, the first step is to conf igure wireless communication parameters within the W ireless Settings page. This page only c onfigures the card to communicate to a target W AP (such as t[...]

Configuring Communications 16 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Setup the security and communication parame ters between the wireless card and the target W AP by configuring the W ir eless Settings section on this page. Refer to Step 2: Configur e the Card’ s W ire less Security Settings section on page 20 for [...]

Configuring Communications 17 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 2. In the lower -right corner of the W ireless Settings page, press the Simple b utton to open the Wi re l e s s Security: Simple Mod e window ( FIG. 15 ). 3. Select between the Security T ypes: Open, WEP , and WP A-PSK.  When selecting Open as a [...]

Configuring Communications 18 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom select between WEP Ke ys 1 through 4, and press the A uthentication field to select between Open and Shared.  When se lecting WP A-PSK as a Security T ype, only the SSID and Pa s s w o r d fields are enabled. Press each to open the ap propriate ke[...]

Configuring Communications 19 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Provisioning is Disabled; if it is Enabled, se lect between NEVER, 1 Da y , 3 Days, 7 Days, 14 Days, or 30 Days. 3. When f inished , press the Sa ve button to sa ve all changes and return to the W ir eless Settings page. Press the Cancel button to retur[...]

Configuring Communications 20 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  If a W AP displayed in th e list is not detected for 10 scans in a row , it is then removed from the screen. In this w ay , a user can walk around a b uilding and see access points come and go as th ey mov e in and out of range. 3. Sort the infor[...]

Configuring Communications 21 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring the Modero ’s wireless card for unsecured access to a WAP200G In the Pr otec ted Setup page: 1. Press the Wir eless Settings button (located on the upper-left) to open the W ir eless Settings page. 2. Enter the SSID information by either: [...]

Configuring Communications 22 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 4. Press the red SSID f ield to display the on-screen Netwo rk Name (SSID) keyboard. 5. In this keyboard, enter the SSID name used on your tar get W ireless Access Point ( case sensitiv e ).  The card should be gi ven t he SSID used by the target [...]

Configuring Communications 23 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring the Mo dero’s wireless ca rd for secured access to a WAP200G After logging into the W AP200G, the default Status page appears within the web bro wser . These  read-only v alues are "pulled" from some of the ot her user -config[...]

Configuring Communications 24 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Manually set SSID In the Pr otec ted Setup page: 1. Select Wir eless Settings . 2. In the IP Settings section, press the DHCP/Static field until it reads "Static". 3. Press the Simple b utton to open the W ireless Security: Simple Mode window [...]

Configuring Communications 25 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  The card should be gi ven the SSID used by the tar get W AP . If this field is left blank, the unit will attempt to connect to the first a vailable W AP . By default, all W AP200Gs use AMX as their assigned SSID value.  One of the most comm[...]

Configuring Communications 26 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 9. The Curr ent K e y field is gre yed-out and cannot be altered by the user . The Authentication f ield may be switched from Open to Shared. 10. When f inished, press the Sa ve button to sa ve all changes and return to the W ir eless Settings page. Pre[...]

Configuring Communications 27 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Step 3: Choose a Master Connection Mode The panel requires you establish the type of connection you want made between it and your master . In the Pr otec ted Setup page: 1. Select System Settings. 2. Select T ype to toggle between the Master Connection [...]

Configuring Communications 28 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom panel is recognized as a unique USBLAN device, and the association to the driv er is handled automatically . 1. Connect the PS4.4 power connector to the panel (or docking station if the panel is already installed) to supply power . 2. Press and hold the[...]

Configuring Communications 29 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configure a Vir tual NetLinx Maste r using NetLinx Stu dio A V irtual NetLinx Master (VNM) is u sed when the target panel is not connected to a physical NetLinx Master . In this situation, the PC takes on the functi ons of a Master via a V irtual NetLin[...]

Configuring Communications 30 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. Click the Communications Settings button to open the Communications Settings dialog. 4. Click the NetLinx Master radio button ( fr om the Platform Selection section ). 5. Click the V irtual Master radio button ( fr om the T ransport Connection Option[...]

Configuring Communications 31 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Master Connection to a Virtua l Master via Ethernet Before beginning: 1. V erify the panel has been configured to communica te with the W ireless Access Point and verify the signal strength quality bargraph is On. 2. Launch NetLinx Studio 2.x (default l[...]

Configuring Communications 32 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the OnLine T ree tab in the W orkspace window to view the de vices on the V irtual System. The default System value is one . 11. Right-click on the Empty Device T r ee/System entry and select Refresh System to re-populate the list. 12. Connect[...]

Configuring Communications 33 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using G4 Web Control to Interact with a G4 Panel The G4 W eb Control feature allows you to use a PC to interact with a G4 enabled panel via the web . This feature works in tandem with the ne w browser -capable NetLinx Security firmware update ( buil d 3[...]

Configuring Communications 34 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 9. From the W eb Name keyboard, enter a unique alpha-numeric string to identify this panel. This information is used by the NetLinx Security W eb Se rver to display on-screen links to the pane l. The on-scr een links use the IP Addr e ss of the panel an[...]

Configuring Communications 35 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using your NetLinx Master to control the G4 panel Refer to your particular NetLinx Master’ s instruction manual for detailed information on how to download the latest f irmware from www .amx.com . This firmware b u ild enables SSL certificate identifi[...]

Configuring Communications 36 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Click on the G4 panel name link associated with the target panel. A secondary web bro wser window appears on the screen ( FIG. 33 ). 7. Click Ye s from the Security Alert popup windo w to agre e to the installation of the G4 W ebControl application o[...]

Configuring Communications 37 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Enter the W eb Control session password into the Session P assword field ( FIG. 34 ). This passwor d was pr eviously enter ed into the W eb Contr ol P assword f ield within the G4 W eb Control pa ge on the panel. 11. Click OK to send the password to[...]

Configuring Communications 38 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Upgrading MVP Firmw are 39 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Upgrading MVP Firmware Except for the MVP-KS (Kickstand for MVP Panels), all MVP panels and their accessories hav e on- board firmw are which is upgra deable through the use of the latest NetLinx Studio. The MVP acts as a bridge between the NetLinx Studio [...]

Upgrading MVP Firmware 40 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Upgrading the Modero Fi rmware via the USB port Before beginning with this section, verify your panel is po wered and the T ype-A USB connector is securely inserted into the PC’ s USB port. The panel must be power ed-on bef ore connecting the mi ni- USB c[...]

Upgrading MVP Firmw are 41 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Click the Edit Settings button ( on the Communications Settings dialog ) to open the V irtual NetLinx Master Settings dialog ( FIG. 35 ). 7. From within this dialog enter the System num ber (default is 1 ). 8. Click OK three times to close the open dial[...]

Upgrading MVP Firmware 42 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 5. If the panel firmw are version is not the latest a v ailable; locate the latest firmw are file from the www .amx.c om > T ech Center > Downloadable Files > Firmware Files > Modero Panels section of the website. 6. Click on the desired Kit fil[...]

Upgrading MVP Firmw are 43 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r e boot of the panel can take up 30 seconds after the f irmwar e process has finished. 11. Click Send to begin the transfer . [...]

Upgrading MVP Firmware 44 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 1. Complete the instructions for configuring the NetLinx Master for IP communication found in the Upgrading the Moder o Firmwar e via the USB port section on page 40. 2. After the panel powers-up, press and hold the two lower b uttons on both sides of the d[...]

Upgrading MVP Firmw are 45 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r e boot of the panel can take up 30 seconds after the f irmwar e process has finished. 11. Click Send to begin the transfer . [...]

Upgrading MVP Firmware 46 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Although firmware u pgrades can be done over wireless Ethernet; it is recommended that firmware KIT files be transfer red over a direct USB connection and only when the panel is connected to a power supply . If battery power or wireless conne ction fails du[...]

Setup Pages 47 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setup Pages AMX Modero panels feature on-board Setup pages. Us e the options in th e Setup pages to access panel information and make various conf iguration changes. T o access the Setup pages, press the two lo we r external pushb uttons on either side of the panel si[...]

Setup Pages 48 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setup Pages The Setup page ( FIG. 43 ) allows quick access to se veral basic panel properties: Features on this page include: FIG. 43 MVP-8400 Setup page Setup Page Navigat ion Butto ns: The buttons along on the left side of the page provide access to secondary Setup [...]

Setup Pages 49 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Settings The Pr otected Settings page and its contents are cove red in more detail in the Pr otected Setup Pa g e s section on page 60. Information The Information b utton provides a menu to select either the Pr oject Information P age section on page 50 or [...]

Setup Pages 50 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Project Informati on Page The Project Information page d isplays the project properties of the TPDesign4 project file currently loaded on the panel ( FIG. 45 ). Features on this page include: FIG. 45 Project Information page Project Information Page Back: Saves all ch[...]

Setup Pages 51 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Project Information Page (Cont.) IR User Def 1 Port: Displays the User Defined IR channel port used by the IR Emitter on the panel. • Note : User Defined ports can be downloaded by the user and are customizable, whereas the AMX ones are fixed. IR User Def 2 Port: Di[...]

Setup Pages 52 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Information Page The Panel Information page provides detailed panel information ( FIG. 46 ). Features on this page include: FIG. 46 Panel Information page Panel Information Page Back: Saves all changes and returns to the previous page. Connection Status icon: Th[...]

Setup Pages 53 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Information Page (Cont.) Screen Refresh Rate: Displays the video refresh rate applied to the incoming video sign al from the panel. Screen Rotation: D isplays the degree of rotation applied to the on-screen image. Power Up Pages: D isplays the page assigned to d[...]

Setup Pages 54 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Time & Date Settings The options on the T ime & Date Settings page ( FIG. 47 ) allo w you to set and adjust time and date information on the NetLinx Master . If the time and/or date on the Master is modified, all connected devices will be updated to reflect th[...]

Setup Pages 55 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Time & Date Settings Page (Cont.) Set Date/Time: Use the UP/DN arrow buttons to adjust the Maste r ’s calendar date and time. The blue icon indicates which fiel d is currently selected (see FIG . 47 ). • Y ear rang e = 2000 - 2037 • Month range = 1 - 12 • [...]

Setup Pages 56 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Audio Settings The MVP-8400i provides an Audio Settings page ( FIG. 48 ) with options that allow you to adjust v olume lev els, set intercom sou nd and microphone lev e ls, and set panel sounds. Features on these pages include: FIG. 48 Audio Adjustments/Volum e pages [...]

Setup Pages 57 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom En vironmental acoustics, personal voice le vel and am bient noise are all deciding factors when setting your mic, intercom and panel sound lev els. Consider your en vironment when adjusting intercom and sound lev els and use cau tion so as not to damage the speaker .[...]

Setup Pages 58 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Battery Settings The options on this page allow you to set po wer warning preferences, monitor battery status information, and adjust the display times for battery warnings. This page is populated with information from MVP-BP batteries in the panel, as well as batteri[...]

Setup Pages 59 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Battery Settings Page (Cont.) Low Battery Warning: The UP/DN buttons adjust the time value (in minutes) available on the battery (for use) before the panel displays a low battery warning. Range - 10, 15, 20, 30, 45 default = 15 min. Note : This field applies to MVP-BP[...]

Setup Pages 60 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Pages The Protected Setup page ( FIG. 50 ) provides secured access to a dvanced panel conf iguration options, including communication and security settings. Enter the factory default password ( 1988) into the passw ord ke ypad to access this page. Feat[...]

Setup Pages 61 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Page (Cont.) Docking Station: • Dock Status - illuminates when the MVP is docked and communicating with the Docking S tation. • Undock Panel - forces the docking station to release the MVP without requiring a User Access username or password. • D[...]

Setup Pages 62 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Navigation Buttons The Protected Setup Navigation Buttons ( FIG. 52 ) appear on the left of the panel screen when the Protected Setup page is currently activ e. FIG. 52 Protected Setup Navigation Buttons Press to access the G4 W eb Contro l page where [...]

Setup Pages 63 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom System Settings Page The System Settings page ( FIG. 53 ) displays sets the NetLinx Master’ s commun ication settings. The elements of this page include: FIG. 53 System Settings page System Settings Page Elements Back: Saves all changes and returns to the previous p[...]

Setup Pages 64 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the Step 3: Choose a Master Connection Mode section on page 27 for more detailed information on using the System Settings page. System Settings Page Elements Master Connection (Cont.): Mode Cycles between the connection modes: URL, Listen, and Auto. (Ethernet[...]

Setup Pages 65 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Wireless Settings Page Use the options on the Wireless Settings page ( FIG. 54 ) to conf igure communication settings for the wireless CF card (802.11g), and read the de vice number assigned to the panel. Features on this page include: FIG. 54 Wireless Settings page ([...]

Setup Pages 66 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Pressing the Simple or Enterprise b uttons at the bottom of the Information/Configur ation section open an appropriate W ireless Security window for Simple Mode or Enterprise Mode. Simple Mode is best used for smaller installations that use a single Ma ster , such as [...]

Setup Pages 67 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom FIG. 55 Wireless Security: Simple Mode Wireless Security: Simple Mode Security T ype: This field may be switched between WEP , WP A-PSK, and Open. If WEP is selected, the button to the right may be switched between 64 and 128 . • WEP security requires that both a ta[...]

Setup Pages 68 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom FIG. 56 Wireless Security: En terprise Mode Wireless Security: Enterprise Mode Security T ype: Pressing this field changes the secu rity type being used between EAP-PEAP , EAP-TTLS, EAP-TLS, EAP-LEAP , and EAP-F AST . • EAP-PEAP security is designed for wireless env[...]

Setup Pages 69 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Wireless Settings The options on the W ir eless Secur ity: Simple Mode and W ir eless Security: Enterprise Mode windows allow you to select from the wireless security methods supported b y the NXA-WC802 11GCF W i-Fi card. These security methods incorporate WP A , WP A[...]

Setup Pages 70 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Open Settings Open security does not utilize any encryption methodology , but requires an SSID (alpha-numeric) entry . This entry must match the Network Name (SSID) en try of the target W AP so the panel kno ws what de vice it is using to communicate with the network.[...]

Setup Pages 71 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom WEP Settings (Cont.) Generate (Passphrase): This button displays an on-screen keyboar d which allows you to enter a passphrase. The panel then automat ically generates four WEP keys (compatible only with Modero panels). Enter these WEP keys into the target WA P . When[...]

Setup Pages 72 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  Refer to the Configuring a W ir eless Network Access section on page 15 for further details on these security options.  Refer to the Using the Site Survey tool section on page 19 for more information on using this feature. WPA-PSK Settings WP A-PSK securi[...]

Setup Pages 73 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-LEAP Setting s EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both wired and wireless network en vironments. EAP requires the use of an 802.1x Authentication Server , also known as a Radius server . The config[...]

Setup Pages 74 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-FAST Settin gs EAP-F AST (Flexible Authentication via Secure T unneling) security was designed for wireless en vironments wh ere security and ease of setup are e qually desirable. EAP-F AST uses a certificate file, howe ver it can be configured to do wnload the ce[...]

Setup Pages 75 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  Refer to the EAP Authentication section on page 185 for further details on these security options.  Refer to the Using the Site Survey tool section on page 19 for more information on using this feature. EAP-PEAP Settings PEAP (Protected Extensib le Authen[...]

Setup Pages 76 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  Refer to the EAP Authentication section on page 185 for further details on these security options.  Refer to the Using the Site Survey tool section on page 19 for more information on using this feature. EAP-PEAP Settings (Cont.) Password: Opens an on-scre[...]

Setup Pages 77 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-TTLS Setting s TTLS (EAP T unnele d T ransport Layer Security) is an authentication method that does n ot use a client certificate to authenticate the panel. Howe ver . this method is more se cure than PEAP because it does not broadcast the identity of the user . [...]

Setup Pages 78 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  Refer to the EAP Authentication section on page 185 for further details on these security options.  Refer to the Using the Site Survey tool section on page 19 for more information on using this feature. EAP-TTLS Settings (Cont.) Certificate Authority: Whe[...]

Setup Pages 79 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-TLS Settings TLS (T ransport Layer Security) was the original st andard wireless LAN EAP au thentication protocol. TLS requires additional work during th e deployment phase but pro vides additional security since e ven a compromised password is not enough to break[...]

Setup Pages 80 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  Refer to the EAP Authentication section on page 185 for further details on these security options.  Refer to the Using the Site Survey tool section on page 19 for more information on using this feature. Client certif icate configu ration There are sev era[...]

Setup Pages 81 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom It is important to note which certificate types are supported by the different certificate f ield s used on the configuration screens (PEAP , TTLS, and TLS). The following table outlines the f irmware fields and their supported certificate types. Calibrate Page This p[...]

Setup Pages 82 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom G4 Web Control Settings Page An on-board VNC (V irtual Network Computing) server allo ws the panel to connect to any remote PC running a VNC client. Once connected, the client can vie w and control the panel remotely . The options on this page allow you to enable/disa[...]

Setup Pages 83 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom G4 Web Control Page ( Cont.) Current Connection Count Displays the number of users currently connected to this panel via VNC. G4 We b Control T imeout: Sets the length of time (in minutes) that the panel can remain idle (no cursor movements) before the G4 Web Control [...]

Setup Pages 84 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Other Settings The Other Settings button provides a menu to select the Image Cac h ing page, P asswor d Setup page, or SIP Settings page. Select any option to access its page. Cache Settings Page The Cache Settings page ( FIG. 60 ) configures the allocation of memory [...]

Setup Pages 85 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom the situation, as the panel could spend more resour ces processing information rather than continuously waiting on images to arriv e from a slow network. The elements of this page include: DynaMo is an extension of the Dy namic images feature of AMX G4 device s that p[...]

Setup Pages 86 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the image cache In the Pr otec ted Setup page: 1. Press the Cache b utton in the Protected Setup Navigation Buttons section. This opens the Cache Settings page. 2. Set the cache expiration in the field Flash/RAM Cac he Expires . The Up and Down arro ws incre m[...]

Setup Pages 87 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Password Settings Pag e The options on the P asswor d Settings page enable you to assign the passwords required for users to access the Pr ote cted Setup page, and to release the MVP from a MVP-TDS or MVP-WDS docking station ( FIG. 61 ). Features on this page include:[...]

Setup Pages 88 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Password Settings Page (Cont.) User Access: Use these buttons to access and modify the user name/password combinations required for removing the panel from a docking station. The number of user access passwords on the panel is limited only by the amount of storage mem[...]

Setup Pages 89 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Settings Page The options on the SIP Settings page ( FIG. ) enable you to establish network settings for using your touch panel as an IP phone. W ith a CSG SIP Communications Gateway ( FG2182-01, -02, -03 ), you can use your touch panel to make and recei ve local,[...]

Setup Pages 90 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Settings Page (Cont.) Stat u s: T his option enables the SIP S tack on startup. If you disable this option, the panel will not attempt to read the rest of the configuration and will not register with a proxy server. However , point-to-point SIP will still be enabl[...]

Setup Pages 91 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Tools The T ools button provides a menu to select either the P ane l Connection Logs P age section on page 91 , the P anel Statistics P age section on page 93 , or the Connection Utility P age section on page 95 . Select any of the options to access that page . Panel [...]

Setup Pages 92 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Features on this page include: Checking the Panel Connection Logs 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Panel Logs button. All connection data is contained in th[...]

Setup Pages 93 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Statisti cs Page The options on the Panel Statistics page allo w you to track the connection status for the panel. The P anel Statistics page tracks ICSP messages, Blink messages, Ethernet connection statistics, and W irele ss connection statistics ( FIG. 61 ). [...]

Setup Pages 94 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Checking the Pa nel Statistics 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Panel Statistics button. All connection statistics are contained on this page, e.g., Receive[...]

Setup Pages 95 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Connection U tility Page The options on the Connection Utility page allow you to utilize your panel as a site surv ey tool. While in this page, move around your wireless network cov erage area and see if there are any weak points within the spaces between your W APs ([...]

Setup Pages 96 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using the Connection Utility 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Connection Utility button. This launches the Connection Utility popup. 3. Move the panel throu[...]

EAP Security & Server Certifica tes 97 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP Security & Server Certificates Overview The follo wing EAP types all support a server certif icate:  EAP-PEAP  EAP-TTLS  EAP-TLS All three of these certif icate-using security me thods are documented in the followi[...]

EAP Security & Server Certificates 98 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Full Duplex Intercom 99 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Full Duplex Intercom Overview V oIP technology giv es users the ability to instantly create a high-quality , digita l home/off ice intercom network with no additional equipment required. By u tilizing V oIP intercom, system inte gration is simple and calls so[...]

Full Duplex Intercom 100 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the Intercom Session Timeout 1. Select the Setup button on your intercom page. 2. Press the up or down arro ws to increment the timeout up by 1 second in each direction. If your call exceeds your session timeout the panel pro vides you with a popup ([...]

Full Duplex Intercom 101 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Advanced Setup The intercom’ s advanced setup pages are accessed through the intercom setup pages. The advanced pages allow you to set the panel intercom to be monito red, to monitor other intercom panels, and to name the panel. It is important to name the[...]

Full Duplex Intercom 102 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 5. Press Back to return to the intercom setup pages. 6. Press Exit when you are finished. Allowing a panel to mo nitor 1. Select the Setup button on your intercom page. 2. On the intercom setup page, press Advanced Setup . This launches the password numeric [...]

Full Duplex Intercom 103 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Sample Intercom Page The module for duplex intercom capable panels includes user pages. While you can create your o wn intercom directory page (see Cr eating Intercom P ages section on page 106 ), it is possible to use the panel with the page below . FIG. 73[...]

Full Duplex Intercom 104 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Sample Intercom Page ( Cont.) No. Name Descri ption Channel  Po r t:Code Address  Port:Code Level  Port:Code 7 Panel Directory Room Name The name of a panel in the intercom directory . Y ou can call the panel, enact privacy against the panel and mon[...]

Full Duplex Intercom 105 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Answering an incomi ng call The provided intercom pages include an answering popup window . The popup page indicates the name of the panel calling and two options:  Answer - Pressing this button opens the intercom session with the o ther panel.  [...]

Full Duplex Intercom 106 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Creating Intercom Pages The easiest method of creating your o wn intercom pages is to start with the pages pro vided by AMX in the module download .ZIP file. Y ou can change the aesthetics of th e pages as long as th e channel, address, lev e l and links rem[...]

Programming 107 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Programming Overview Y ou can program the touch panel, using the comma nds in this section, to perform a wide variety of operations using Send_Commands and variable text commands. A device must f irst be defined in the NetLin x pr ogramming language with values for t[...]

Programming 108 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) @CPG Clear all popup pages from  specified popup group. Syntax: "'@CPG-<popup group name>'" Va r i a b l e : popup group name = 1 - 50 ASCII characters. Name of the popup group . Example: SEND_COMMAND Panel,"&a[...]

Programming 109 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont.) @PHT Set the hide effect time for the  specified popup page. Syntax: "'@PHT-<popup page name>;<hide effect time>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters. Name of the page the popup is displ[...]

Programming 110 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) @PPK Kill a specific popup page from all pages. Kill refers to the deactivating (Off) of a popu p window from all pages. If the pop-up p age is part of a group, the whole group is deactivat ed. This command works in the same way as the 'Cl[...]

Programming 111 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont.) @PPX Close all  popups on all pages. This command works in the same way as the 'Clear All' command in T PDesign 4. Syntax: "'@PPX'" Example: SEND_COMMAND Panel,"'@PPX'" Close all popups on all[...]

Programming 112 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) PPOF Deactivate a  specific popup page on either a specified page or the current page. If the page name is empty , the cu rr ent page is used (see example 2). If the popup page is part of a group, the whole group is deactivat ed. This comman[...]

Programming 113 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Programming Numbers The follo wing information provides the program ming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents the lightest color-specif ic display; the highest [...]

Programming 114 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom RGB Values for all 88 Basic Colors (Cont.) Index No . Name Re d Green Blue 36 V ery Light Cyan 0 255 255 37 Light Cyan 0 223 223 38 Cyan 0 191 191 39 Medium Cyan 0 159 159 40 Dark Cya n 0 127 127 41 V ery Dark Cyan 0 95 95 42 V ery Light Aqua 0 128 255 43 Light Aqua [...]

Programming 115 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Font Styles and ID Numbers Font styles can be used to program the text font s on buttons, sliders, and pages. The follo wing chart shows the def ault font type and their respectiv e ID numbers generated by TPDesign4. RGB Values for all 88 Basic Colors (Cont.) Index N[...]

Programming 116 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Border Styles and Programming Numbers Border styles can be used to program bor ders on bu ttons, sliders, and popup pages. The TPDesign4 T ouch Panel Design program has pre- set border styles that are user selectable. Y ou cannot use the following number v alues for [...]

Programming 117 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom TPD4 Border Styles by Name (Cont.) No. Border styles No. Border styles 43 Diamond 85 85 Menu Bottom Rounded 65 44 Diamond 95 86 Menu Bottom Rounded 75 45 Diamond 105 87 Menu Bottom Rounded 85 46 Diamond 1 15 88 Menu Bottom Rounded 95 47 Diamond 125 89 Menu Bottom Rou[...]

Programming 118 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands These Button Commands are used in NetLinx Studio and are case insensiti ve. All commands that begin with " ^ " hav e the capability of assigning a variable te xt address range and button state range. A device must f irst be def[...]

Programming 119 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^APF Add page flip action to a button if it does not already exist. Syntax: "'^APF-<vt addr range>,<page flip action>,<page name>'" Va r i a b l e : variable te xt address range = 1 - 4000. p[...]

Programming 120 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BCB Set the border color to the  specified color . Only if the specified border color is not the same as the curr ent color . Note : Color can be assigned by color name (without spaces), number or R,G ,B value (RRGGBB or RRG[...]

Programming 121 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BDO Set the button draw order . Determines what order each layer of the button is drawn. Syntax: "'^BDO-<vt addr range>,<button states range>,<1-5><1-5><1-5><1- 5><1-5>'&q[...]

Programming 122 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BLN Set the number of lines removed equally from the top and bottom of a composite video signal. The maximum number of lines to remove is 240. A value of 0 will display the incoming video signal unaffected. This command is us e[...]

Programming 123 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BMC (Cont.) Example 2: SEND_COMMAND Panel,"'^BMC-150,1,1,315,1,%BR%FT%TX%BM%IC%CF%CT'" Copies the OFF state border , font, T ext, bitmap, icon, f ill color and text color of the button with a variable text ad[...]

Programming 124 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BMF  (Cont.) For some of these commands and v alues, ref er to theRGB V alues for all 88 Basic Colors table on page 113. ’%CF<on fill color >’ = Set Fill Co lor . ’%CB<on border color>’ = Set Border Color[...]

Programming 125 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-square shape. This is typically used with a bitmap. Syntax: "'^BMI-<vt addr range>,<button states range>,<mask image[...]

Programming 126 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BNN Set the T akeNote  network name for the specified Addresses. Syntax: "'^BNN-<vt addr range>,<network name>'" Va r i a b l e : variable te xt address range = 1 - 4000. network name = Use a [...]

Programming 127 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BOR Set a border to a specific border style associated with a border value for those  buttons with a defined address range. Refer to the Border Styles and Programming Numbers table on page 11 6 for more  information. Synta[...]

Programming 128 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BRD Set the border of a button state/ states. Only if the specified border is not the same as the curr ent border . Th e border names are available through the TPDesign4 border-name drop-down list. Syntax: "'^BRD-<[...]

Programming 129 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BSP Set the button size and position. Set the button size and its position on the page. Syntax: "'^BSP-<vt addr range>,<left>,<top>,<right>,<bottom>'" Va r i a b l e : variable t[...]

Programming 130 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BWW Set the button word wrap  feature to those buttons with a defined address range. By default, word-wrap is Off. Syntax: "'^BWW-<vt addr range>,<button states range>,<word wrap>'" Va r[...]

Programming 131 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^ENA Enable or  disable buttons with a set  variable text range. Syntax: "'^ENA-<vt addr range>,<command value>'" Va r i a b l e : variable te xt address range = 1 - 4000. command value = (0=[...]

Programming 132 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^GIV Invert the  joystick axis to move the origin to another corner . Parameters 1,2, and 3 will cause a bargraph or slid er to be inverted regardless of  orientation. Their effect will be as described for joysticks. Synta[...]

Programming 133 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^GSC Change the  bargraph slider color or joysti ck cursor colo r . A user can also assign the color by Na me and R,G ,B value (RRGGBB or RRGGBBAA). Syntax: "'^GSC-<vt addr range>,<color value>'"[...]

Programming 134 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^IRM Set the IR  channel. Pulse the given IR channel for onTime in tenths of seconds. Delay offT ime in tenths o f a second before the next IR pulse is allowed. ^IRM allows the command itself to specify the port number . ^IRM[...]

Programming 135 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^JSI Set icon  alignment using a numeric keypad layout for those  buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '. The left and top coordinates are relative to [...]

Programming 136 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^MDC T urn On the  ’Mouse  double-click’  feature for the  virtual PC. Syntax: "'^MDC'" Example: SEND COMMAND Panel,"'^MDC'" Sets the mouse double-click for use with the vi[...]

Programming 137 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^TEC Set the text effect color for the  specified addresses/states to the specified color . The T ext Effect is specified by name and c an be found in TPD4. Y ou can also assign the color by name or RGB va lue (RRGGBB or RRGGB[...]

Programming 138 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Miscellaneous MVP Stri ngs back to the Master The following tw o strings are sent by the MVP panel back to the communicating Master: "^" Button Commands (Cont .) ^UNI Set Unicode text. For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as[...]

Programming 139 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP Panel Loc k Passcode c ommands These commands are used to maintain a passcode list. From certain panels a password must be entered to remov e the panel from its cradle. Only the passcode is entered. The user is just for identifying the passcodes. MVP Panel Lock P[...]

Programming 140 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Text Effects Names The following is a listing of text ef fects names (associated with the ^TEF command on page 138 ). Text Effects • Glow -S • Medium Drop Shadow 1 • Hard Drop Shadow 1 • Glow -M • Medium Drop Shadow 2 • Hard Drop Shadow 2 • Glow -L • [...]

Programming 141 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands Button Query commands reply back with a custom ev ent. There will be one custom e vent for each button/state combination. Each query is assigned a unique custom e vent type. The following example is for deb ug purposes only: NetLinx Example: CUS[...]

Programming 142 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom These fields are populated dif ferently for each query command. The text length (String Encode) f ield is not used in any command. Button Query Commands ?BCB Get the current border color . Syntax: "'?BCB-<vt addr range>,<button states range>&apo[...]

Programming 143 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BCF Get the current fill color . Syntax: "'?BCF-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu ttons (0[...]

Programming 144 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BMP Get the current bitmap name. Syntax: "'?BMP-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu ttons (0[...]

Programming 145 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BRD Get the current border name. Syntax: "'?BRD-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu ttons (0[...]

Programming 146 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BWW Get the current word wrap flag status. Syntax: "'?BWW-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state b[...]

Programming 147 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?FON Get the current font index. Syntax: "'?FON-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu ttons (0 [...]

Programming 148 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?JSB Get the current bitmap  justification. Syntax: "'?JSB-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-stat[...]

Programming 149 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?JST Get the current text justification. Syntax: "'?JST-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu t[...]

Programming 150 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?ST A Dump XML Panel St a t s Syntax: "'?STA'" Returned in MUL TIPLE Custom events (size of strings are limited per message). V alue s in Custom event will state the number of messages and how many total bytes of xml [...]

Programming 151 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?TEF Get the current text effect name. Syntax: "'?TEF-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000. button states range = 1 - 256 f or multi-state bu tto[...]

Programming 152 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?V O L Show the Master Vo l u m e  information. Syntax: ?VOL-<volume value> Va r i a b l e : V alue1=master volume value ?WIF Show the  Wireless Settings information Syntax: Text=<WAP MAC address>,<SSID>,Channel #[...]

Programming 153 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operations Serial Commands are used in the AxcessX T erminal Emulator mode. These commands are case insensitiv e. Panel Runtime Op eration Commands ABEEP Output a single beep even if beep is Off. Syntax: "'ABEEP'" Example: SEND COMMA[...]

Programming 154 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @AKP Pop up the  keypad icon and initialize the tex t string to that  specified. Keypad string is set to null on power up and is stored until power is lost. The Pro m pt T ext is optional. Syntax: "'@AKP-<i[...]

Programming 155 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @EKP Extend the  Keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt T ext is optional. Syntax: "'@EKP-<initial text>;<prompt text>'" Va r i a b l e[...]

Programming 156 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @SOU Play a sound file. Syntax: "'@SOU-<sound name>'" Va r i a b l e s : sound name = Name of the sound file. Supported sound file formats are: WAV & MP3. Example: SEND COMMAND Panel,"'[...]

Programming 157 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) TP A GEON T urn On page tracking. This command turns On page tracking, whereby when the page or popups change, a string is sent to the Master . This str ing may be captured with a CREA TE_BUF FER  command for one panel and[...]

Programming 158 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Input Commands These Send Commands are case insensitive. Input Comman ds ^CAL Put panel in  calibration mode. Syntax: "'^CAL'" Example: SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode. ^KPS Set the  keyboar[...]

Programming 159 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Input Command s (Cont.) ^MPS Set mouse pass through. Allows mouse input to multiple  destinations simultaneously . Destinations are comma delimited. Note: This command causes all mice connected to the G4 product and any mice on a computer connected via a VGA card [...]

Programming 160 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Embedded codes The following is a list of G4 compatible embedd ed codes: Embedded Codes Decima l nu m ber s Hexidecimal values V ir tual keystroke 8 ($08) Backspace 13 ($0D) Enter 27 ($1B) ESC 128 ($80) CTRL key down 129 ($81) AL T key down 130 ($82) Shift key down 1[...]

Programming 161 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands These commands are case insen sitiv e. Panel Setup Commands CLOCK Sets the time and date on the panel. Syntax: “’CLOCK mm-dd-yy hh:mm:ss’” V ariables: mm = Month dd = Day yy = Y ear hh = Hour mm = Minute ss = Second Example: SEND_COMMAND [...]

Programming 162 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands (Cont.) ^CFSM Sets the Flash cache to the maximum  available size allowed for backup Flash cache. (determined by taking 75% of free Flash space) Syntax: “’^CFSM’” V ariable: There is no parameter for this command. Example: SEND_COMMAND[...]

Programming 163 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands (Cont.) ^ICM-SPEAKERLEVEL Set the speaker level during an intercom call. Syntax: "'^ICM-SPEAKERLEVEL,<level>'" V ariables: 0 - 100 volume le vels Example: SEND_COMMAND Panel, “^ICM-SPEAKERLEVEL,55” Sets the speaker v[...]

Programming 164 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Dynamic Image Commands The following table describe s Dynamic Image Commands. Panel Setup Commands (Cont.) ^V OL Set the panel  volume. Syntax: "'^VOL-<volume level>'" V ariable: volume le vel = 0 - 100. 100 is maxim um volume setting. Ex[...]

Programming 165 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource pa rameters by sending embedded codes and data: "'^RAF-<resource name>,<data>'" "'^RMF-<resource name>,<data>'" [...]

Programming 166 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Escape Sequences The ^RAF and ^RMF commands support the replacement of any special escape se quences in the filename (specif ied by the %F embedded code) with the corre sponding data obtained from the system as outlined in the table below: ^RAF, ^RMF - Embedded Codes[...]

Programming 167 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom For in st an c e, http://www .amx.com/i mg.asp?de vice=$DV would become http://www .amx.com /img.asp?device=10001. Intercom Commands The following is a listing and descriptions of panel intercom commands. Escape Sequences (Cont.) Sequence Panel Inf o r mation $LC Lev[...]

Programming 168 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Intercom Co mmands (C ont.) ^ICS S tarts an  intercom call to the specified IP address and ports. ^ICS-<IP>,<TX UDP port>,<RX UDP port>,<initial mode>'" Intercom start. S tarts a call to the specified IP address and ports, where i[...]

Programming 169 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands The following table lists and describes SIP comma nds that are generated from the touch panel. SIP Commands ^PHN- A UTO ANSWER Provides the state of the auto-answer feature. Syntax: "'^PHN-AUTOANSWER, <state>'" Va r i a b l e : [...]

Programming 170 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The following table lists and describes SIP commands that are sent to the touch panel to manage calls. SIP Commands (Cont.) ^PHN- MSGW AITING Indicates the number of messages waiting the user ’s voice mail box. Syntax: "'^PHN-MSGWAITING, <messages>,[...]

Programming 171 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands (Cont.) ?PHN- A UTO ANSWER Queries the state of the auto-answer feature. The panel responds with the ^PHN-AUTOANSWER, <state> message. Syntax: "’?PHN-AUTOANSWER’" Example: SEND_COMMAND Panel,"'?PHN-AUTOANSWER'" ^PH[...]

Programming 172 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The following table lists and describes SIP setup commands. Using any of these commands ca uses the current user to go offline. SIP Commands (Cont.) ^PHN-REDIAL Redials the last number . Syntax: "’^PHN-REDIAL’" Example: SEND_COMMAND Panel,"'^P[...]

Programming 173 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands (Cont.) ^PHN-SETUP- STUNADDR Sets the IP address for the STUN server . Syntax: "’^PHN-SETUP-STUNADDR,<IP>’" Va r i a b l e : IP = The IP address for the STUN server Example: SEND_COMMAND Panel,"’^PHN-SETUP-STUNADDR,192.168.223.[...]

Programming 174 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Appendix A: Text Formatti ng 175 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks T ext formatting codes for bargraphs pro vide a mechanism to allow a portion of a bargraphs te xt to be dynamically provided information about the current stat us of the level [...]

Appendix A: Text Formatting 176 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Text Area Input Masking T ext Area Input Masking can be used to limit the allo wed/correct characters that are entered into a te xt area. For example, in working with a zip code, a user could limit the entry to a max length of only 5 characters but, w[...]

Appendix A: Text Formatti ng 177 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the following Send Commands for more detailed information: Input mask ranges These ranges allow a user to specify the min imum and maximum numeric value for a field. Onl y one range is allow ed per field. Using a range implies a numeric entr[...]

Appendix A: Text Formatting 178 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom A keyboard entry using normal text entry is straightforward. Ho we ver , once an input mask is applied, the behavior of the k eyboard needs to change to accommodate the input mask's requireme nt. When working with masks, any literal characters in[...]

Appendix A: Text Formatti ng 179 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom URL Resources A URL can be broken into se veral parts. For e xample: the URL http://www .amx.com/company-info- home.asp . This URL indicates that the protocol in use is http (HyperT ext Tr ansport Protocol) and that the information resides on a host [...]

Appendix A: Text Formatting 180 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Appendix B - Wireless Technology 181 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix B - Wireless Technology Overview of Wireless Technology  802.11b/2.4 GHz and 802.11a/5 GHz are the two major WLAN standards and both operate using radio frequency (RF) technology . T ogether the two standards are together called W [...]

Appendix B - Wireless Technology 182 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Although the calculations required to encrypt data with WEP can impact the performance of your wireless network, it's generally seen only when running benchmarks, and not large enough to be noticeable in the course of normal network usage. T[...]

Appendix B - Wireless Technology 183 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  TKIP  Short for T emporal Ke y Integration, is pa rt of the IEEE 802.11i encryption standard for wireless LANs. TKIP provides per -packet ke y m ixing, message integrity check and re-keying mechanism, thus ensuring ev ery data packet[...]

Appendix B - Wireless Technology 184 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom  WP A2  Also know as IEEE 802.11i, is an am endment to the 802.11 standard speci fying security mechanisms for wireless networks. The 802.11i sch eme makes use of the Advanced Encryption Standard (AES) block cipher; WEP and WP A use t[...]

Appendix B - Wireless Technology 185 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP Authentication EAP (Extensible Authentication Proto col) is an Enterprise authentication protocol that can be used in both a wired and wireless network environment. EAP requires the use of an 802.1x Authenticatio n Server , also known as a Ra[...]

Appendix B - Wireless Technology 186 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP communication overview EAP Authentication goes a step beyond just encrypting data transfers, b ut also requires that a set of credentials be validated before the client (panel) is allo wed to connect to the rest of the network ( FIG. 77 ). Be[...]

Appendix B - Wireless Technology 187 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom AMX Certificate Upload Utility The Certif icate Upload utility gi ves you the ability to compile a list of tar get touch panels, select a pre- obtained certificate (uniquely identifying the panel), and then upload that f ile to the selected panel[...]

Appendix B - Wireless Technology 188 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Step 2: Confirm t he Installation of the USB Driver on the PC The first time each AMX touch panel is connected to the PC it is detected as a new hardware de vice and the USBLAN driv er becomes associated with it (pan el specific). Each time there[...]

Appendix B - Wireless Technology 189 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 11. Launch the Certificate Upload Utility and confirm the utility has detected the new USB connection to the panel:  Click on the Local Address f ie ld's drop-do wn arrow .  Conf irm the new USB entry sho ws up in the list as: 10[...]

Appendix B - Wireless Technology 190 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 12. Select the target de vices which be uploaded with the selected certificate. These can either be:  indi vidually selected by toggling the box next to the Send entry (with the T ype column).  selected as a group by clicking on the C[...]

Appendix C: Troubleshooting 191 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix C: Troubleshooting This section describes the solutions to possible ha rdware/f irmware issues that could arise during the common operation of a Modero touch panel. Checking AMX USBLAN Devi ce Connections via Window s Device Manager AMX USBLA[...]

Appendix C: Troubleshooting 192 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom If there is a yello w exclamation point ne xt to the AMX USB LAN LINK de vice (within the hardware devices section of the Unplug or Eject Hardware window), stop and close the USB operation. Re connect the USB cable to the panel and repeat the setup pr[...]

Appendix C: Troubleshooting 193 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom USB Driver Symptom: My USB driver has a yellow e xclamation point and doesn’t appear to be working . The USB driv er was incorrectly installed and should be re-installed: 1. Power up the panel without connecting the USB cable. 2. Plug in the USB cab[...]

Appendix C: Troubleshooting 194 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Plug-in the mini-USB cable into the corresp onding port on the panel. 7. W ait a few seconds and refresh the system. This re-establishes communication with the V irtual Master . The pane l should now appear in the list of av ailable devices. Connec[...]

Appendix C: Troubleshooting 195 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Modero Panel Isn’ t Appearing in The On line Tree Tab 1. V erify that the System number is the same on both the NetLinx Project Navigator windo w and the System Settings page on the Modero panel. 2. V erify you hav e entered the proper NetLinx Maste[...]

Appendix C: Troubleshooting 196 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The pinging is to determine if the Master is av ailabl e and to reply with a connection failure instantly if it is not. W ithout using the ping feature, you will still attempt to make a connection, but a failure will take longer to be recognized. When[...]

Appendix C: Troubleshooting 197 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Fails to Charge in MVP-WDS Should the panel fail, either the unit has no display or fails to boot passed the AMX logo, or does not charge in the MVP-WDS follo w these steps: 1. One person must hold down the blue button on the front of the dockin[...]

Appendix C: Troubleshooting 198 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom[...]

Appendix C: Troubleshooting 199 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Int ercom[...]

4/11 © 2011 AMX. All rights reserved. AMX and the AM X logo are register ed trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • w[...]