Antec Eleven Hundred manual

1 Eleven Hundred User Manual[...]

2 Eleven Hundred User Manual Congratulations on your purchase of the Antec Eleven Hundred! The new flagship in A ntec’s Gaming series, the Ele ven Hund red, brings ultimate g aming builds t o life. The Eleven Hun dred’s nine expansion slots and sp ace for an XL -ATX motherb oard acco mmodate elite GPU configurati ons up to 3-way NVI DIA® SLI®[...]

3 Table of Contents Section 1: Intro duction 1.1 Getting to Know Your Chas sis ............................................................................ 5 1.2 Chassis Specifications ......................................................................................... 6 1.3 Included Screws .....................................................[...]

4 Section 1 Introduction Eleven Hundred Use r Manual[...]

5 1.1 Getting to Know Your Chassis 1. 3 x 5.25” tool -less dri ve bays 2. 2 x 2.5” drive ba ys (dedicated) 3. 6 x 3.5” drive ba ys: tool -less rail-m ount design 4. 1 x 200 mm blue LED top fan 5. 1 x 120 mm r ear fan 6. 2 x 120 mm side panel fans to cool grap hics cards ( optional) 7. 2 x 120 mm interna l intake fans ( optional) 2 x 120 mm fr[...]

6 1.2 Chassis Specification s Chassis Type Super Mid-Tower Chassis Color Black Dimensions 20.7” (H) x 9.3” (W) x 21.5” (D) 527 mm (H) x 2 37 mm (W) x 546 mm (D) Weight 20.0 lbs / 9.0 kg Cooling - 1 x 200 mm blue LED top fan (standard) - 1 x 120 mm r ear fan (standard ) - 1 x 120 mm inta ke fan beh ind motherboard for CPU cooling (optional) - [...]

7 1.4 Before You Begin In order to ensure that your build ing experience with the Eleven Hundred will be a positive one, please take note of the following: While working inside your Eleven Hu ndred, keep your chassis on a fla t, stable surface. M ake sure your build en vironment is clean, w ell-lit, and fre e of dust. Antec chassis fea ture round e[...]

8 Section 2 Hardware Installation Eleven Hundred Use r Manual[...]

9 2.1 Setting Up Put the case uprig ht on a flat, stable surface s o that the rear pan el (power sup ply and expansion sl ots) is facing you. To remove the l eft and right sid e panels, rem ove each of the two thu mbscrews fir st. Remove the panel by gripping the end of the pan el at the top & botto m and swinging the panel outward. Do not pull[...]

10 2. 3 Motherboard Installa tion Before proceeding: Check the manual fo r your CPU co oler to find out if th ere are steps y ou must do before installing the motherboard. Make sure you hav e the correct I /O panel for your motherboard. If the panel provided wi th the chassis isn’t suitable, please contact y our motherb oard manufacturer for the [...]

11 2. 4 Installing KUHLER H 2 O Liquid Coolers The following instru cts how to install the Antec KUHLER H 2 O liquid CPU cooler (620 / 920). F or any other CPU coolers, pleas e consult your manufacturer’s installation guid e. Caution : Check your motherb oard’s CPU soc ket to ensure its compatibility with th e KUHLER H 2 O. The KUHLER H 2 O 620[...]

12 3. Preparing the KUH LER H 2 O backplate is specific to you r CPU socket. Pl ease refer to the KUHLER H 2 O installation guide, available at http://www.antec.c om/Bel ieve_it/product.php ?id=Mjc2OC YxNw== (KUHLER H 2 O 620) or http://www.antec.c om/Bel ieve_it/product.php ?id=NzA0Mzc wJjE3 (KUHLER H 2 O 920) for m ore information. 4. Prepare the[...]

13 Press down on the drive cover t abs. 2. 6 External 5.25” Device Installation Before you begin, you should rem ove the front bezel as direct ed in Section 2.2. 1. Remove the front bez el as directed in S ection 2.2. 2. Remove the dri ve bay cove r by pressing down on the cover tab s and then lifting the cover out from the inside of the bezel. 3[...]

14 2. 7 Internal 2.5” D evic e Installation There are two dedi cated 2.5” dri ve bays in the El even Hund red. To install a 2.5” d rive: 1. With the side panel open, slid e your 2.5” drive into the drive bay so that the dri ve’s holes align with the drive bay h oles. 2. Secure your drive wi th the 2.5” scr ews provided ( D in Section 1.[...]

15 2. 8 Internal 3 .5” Devic e Installation The Eleven Hund red includes 6 pairs of 3.5” drive rails. You will need 1 pair per 3.5” drive. 1. Line up the drive rail pins to the sides of your 3. 5” drive. Ensure that the squ eeze-tabs are aligned on the side of your drive that does n ot have power or data connect ors. 2. Snap the rail int o [...]

16 Use the grom met-lined cable ro uting holes to rout e PSU cables. 2. 9 Cable Managemen t There is a cable managemen t compartment bet ween the motherb oard and right side panel, as well as cable ties located on the back of the motherboard pa nel. You can tuc k excess ca bles in this compartment or r oute them to the dri ve bays. Choose the cable[...]

17 Section 3 Front I/O Ports Eleven Hundred Use r Manual[...]

18 Pin Signal Na mes Pin Signal Na mes 1 USB Powe r 1 2 USB Powe r 2 3 Negati veSignal 1 4 Negati veSignal 2 5 Positiv eSignal 1 6 Positiv eSignal 2 7 Ground 1 8 Ground 2 9 Key (No Co nne cti on ) 10 Em pty Pin 3.1 USB 2.0 Connect the front I/O panel USB cab le to the USB hea der pin on your motherboard . Check your motherboard user’s manual to e[...]

19 Pin Sign al Names (HDA) Pin Sign al Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC P owe r 4 AVCC 4 N C 5 FRO -R 5 Line Out (R) 6 MIC2_ J D 6 Line Out (R) 7 F_IO_ SEN 7 N C 8 Key (no pin) 8 Key (no pin) 9 FRO -L 9 Line Out (L) 10 LINE2_JD 10 Line Out (L) 3.3 AC’97 / HD Au dio Ports There is an Intel ® standard 10- pin AC’97 c[...]

20 3.5 Rewiring Motherboa rd Header Connections There may co me a time wh en you need to rec onfigure the pin-out of a motherboard header c onnector. Examples could be f or your USB header, audio input h eader, or some other front p anel connector such as the Power Butt on connector. Before perfor ming any work, pleas e refer to your motherboard us[...]

21 Section 4 Cooling System Eleven Hundred Use r Manual[...]

22 4.1 Includ ed Fans The Eleven Hund red comes with t wo standard single-speed fans (yellow outline) – a rear 120 mm fan and a top 2 00 mm blu e LED fan. You can turn the top fan’s LED off using the switch on the back of the cha ssis. The red rectangle s indicate additional fan mounts. Mounting pro cedures for these fans is discussed in Sectio[...]

23 Internal intake 120 mm fans Just outside of the 3.5” drive bay ar ea are two fan mounts for 120 mm internal intake fan s. 1. Align your fan with th e pegs that corr espond with the fan screw h oles on the fan. 2. Push your fan into the slot until secure. You will hear your fan lo ck into place when the brackets around th e fan snap into plac e[...]

24 4.3 Air Filters There are two filter s in the Eleven hundred that can be removed and cl eaned: the front filt er and the PSU intake filter. You can acces s the front filter by opening the fr ont door and pushing down on the tabs at th e top of the filter. To remove the fr ont air filter: 1. Remove the front bez el as described in Section 2.2. 2.[...]

25 Antec, Inc. 47900 Fremont Bl vd. Fremont, CA9453 8 tel: 510- 770 -1200 fax: 510-770-1288 Antec Europe B .V. Stuttgartstraat 12 3047 AS Rotterda m The Netherlands tel: +49- 40 -226139- 22 fax: +31 (0) 10 43 7-1752 Technical Suppo rt US &Canada 1-800-22ANTEC customersupport@ant ec.com Europe +31 (0) 10 462-206 0 europe.techsupport@ antec.com w[...]