Aztech Systems WL635USB manual

U U s s e e r r M M a a n n u u a a l l WL635USB Wireless B/G USB 2.0 Adaptor User Manual Version 1.1 CONTENTS 1 INTRODUCTION TO WL635USB WIRELESS B/G USB 2.0 ADAPTOR ................................ 3 1.1 P ACKAGE C ONTENTS .................................................................................................................... 3 1.2 F [...]

U U s s e e r r M M a a n n u u a a l l Declaration of Conformity FCC Certification The United States Federal Communication Comm issi on (FCC) and the Canadia n Department of Communications have established ce rtain ru les governing the u se of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rul e s. Operation is subj[...]

U U s s e e r r M M a a n n u u a a l l 1 Introduction to WL635USB Wireless B/G USB 2.0 Adaptor The WL635USB Wireless B/G USB 2.0 Adaptor is designed for creatin g a wireless workstation for notebook or desktop computer . It is compatible with any USB-eq uipped computers. The WL 635USB Wirele ss B/G USB 2.0 Adaptor is compliant with both Wirel ess-[...]

U U s s e e r r M M a a n n u u a a l l 1.3 LED Indicators Power Indicator (Green LED): The LED will light up when the device is connec ted to a network (an AP or Peer-to-Peer). The LED will blink when the device i s scanning for all available networks. Act Indicator (Green LED): The LED will flicker when there is tran smitting/receiving of wireles[...]

U U s s e e r r M M a a n n u u a a l l 2 Installation 2.1 System Requirements • Desktop PC or Notebook PC • Pentium® 233 processor or higher • 128MB RAM • 20MB hard disk space (sy stem files and modem driver only) • A free USB Port • CD-ROM drive • Windows® 98 SE / Windows® Me / Windows® XP / Windows® 2000 2.2 Step 1: Install th[...]

U U s s e e r r M M a a n n u u a a l l 3. The below screen will be shown. Click “ Next ” to continue. 4. The below screen will be shown. Click “ Next ” to continue and the install ation program will start running automatically. 5. For Windows 2000 and Windo ws XP , you may be prompted for Digital Signature not found. Just click “ Yes ”[...]

U U s s e e r r M M a a n n u u a a l l 2.3 Step 2: Install the Device Note: Before you install the device to y our computer, make sure you have installed the driver and utility as described in the previous section. 1. Locate your USB host and insert the USB 2.0 Adaptor . 2. Once the device has been inserted to your compu ter, Windows will detect t[...]

U U s s e e r r M M a a n n u u a a l l Page 8 of 22 Page 8 of 22 For Windows XP 4. Windows may ask to connect to Window s Update to search for softwa r e. Select “ No ”. When below is prompted, click “ Next ” to continue the installation. hen the “ Hardware Installation ” screen appears, click “ Con tinue Anyway ” to continue . Whe[...]

U U s s e e r r M M a a n n u u a a l l 2.4 Verify Installation To verify if the device exists in your computer and works, go to Start Æ Se ttings Æ Control Panel Æ System Æ Hard w are Æ Device Manager . Expan d the Network Adaptors category. If the WL635USB Wireless B/G USB Adapter is listed here, it means that your device is properly install[...]

U U s s e e r r M M a a n n u u a a l l 3 Network Connection Once the device driver is well installed, a netwo rk setting described in the following sh ould be also established. 3.1 In Windows 98SE/ME 1. Go to Start Æ Settings Æ Control Panel Æ Net w ork . Make sure that all the required components are installed. If any components are mi ssing, [...]

U U s s e e r r M M a a n n u u a a l l 4. Click the “ Access Control ” tab. Make sure that “ Share-lev e l access control ” is select ed. If connecting to a Netware server, share level can be set to “ User-lev el access control ”. 5. When finished, restart your computer to activate the new device. 3.2 In Windows 2000/XP 1. For Windows [...]

U U s s e e r r M M a a n n u u a a l l 4 IP Address 1. To configure a dynamic IP addre ss check the “ Obtain an IP Address Auto matically ” option. 2. To configure a fixed IP, check the “ Use the following IP address ” option. Then enter an IP address into the empty field. For exam ple, enter 192.168.1.1 in the IP addre ss field and 255.25[...]

U U s s e e r r M M a a n n u u a a l l 5 Configuration Utility After the wireless USB 2.0 adaptor has been su ccessfully installed, users can use the included Configuration Utility to set their preference. To activate the Configuration Utility, you may go to Start J Program J WL63 5USB Wireless B+G J WL635USB Wireless B+G Utility . There is also a[...]

U U s s e e r r M M a a n n u u a a l l 5.1 Main Tab Open up the Configuration Utility and the below screen will display the current status of the WL635USB Wireless B/G USB 2.0 Adaptor . Item Description Configure using Windows Zero Config. External Configuration Chec kbox (Wind ows XP only): A checkbox that enables you to disable the WLAN Station [...]

U U s s e e r r M M a a n n u u a a l l Item Description Tx Rate /Rx Rate The actual instantaneous tran smit and receive rates, in Mbps. Signal quality The signal strength from the netwo rk Access Point or station. The strength is displayed in three form ats: a signal quality level (one of five levels, from Bad to Best), a numerical value in dBm, a[...]

U U s s e e r r M M a a n n u u a a l l Item Description Select Hexadecimal (Hex) if you are using hexadecimal numbe rs (0-9, or A-F). Select ASCII if you are using ASCII characte rs (case-sensitive). A SCII characters are: 0,1,2 ,...8,9 and a,b,c,d,...x,y,z. 10 Hexadecimal digits or 5 ASCII cha racters are needed if 64-bit WEP is used; 26 Hexadeci[...]

U U s s e e r r M M a a n n u u a a l l Item Description To supply a Personal Certificate : In the User Name field, type in the user name assigned to the certificate. Select a certificate by clicking Bro w se . The standard Wind ows Select Certificate window is displ ayed: Select a certificate from the list, and c lick OK. The name of the certifica[...]

U U s s e e r r M M a a n n u u a a l l Item Description You are supplying a user n ame and password now. The utility prompts you for them each time you try to connect to a network. 2. To provide a user nam e and password now, enter them in the fields provided. Not all values for Authentication Mode are available for all Securit y settings. Enable [...]

U U s s e e r r M M a a n n u u a a l l 5.2 Profile Manager Tab The Profile Manager en ables you to create, modify and delete the profiles that the station uses to connect to WLAN networks, to activa te and de-a ctivate profiles, and to raise and lower a profile’s priority. ll profiles are displayed in one of the followin g lists: cannot currentl[...]

U U s s e e r r M M a a n n u u a a l l U U s s e e r r M M a a n n u u a a l l P P a a g g e e 2 2 0 0 o o f f 2 2 2 2 5.3 Information Tab The Information tab displays information maintained by the driver, such as t he number of packet errors and the total number of bytes receive d or transmitted. The tab also displays information about the curren[...]

U U s s e e r r M M a a n n u u a a l l 6 Example of connection to an Access Point 2. The Profile Configuration window will be displayed so t hat you can create a profile. 1. At the Main tab, highlight one of the devices from t he list area that you wish to connect and then press the Connect button to access it. 3. T e w 4. S l . . Select None for [...]

U U s s e e r r M M a a n n u u a a l l 7. The WEP Configuration screen will be shown. 8. Select Hexadecimal (Hex) if you are using hexadecimal nu mbers (0-9, or A-F). 10 Hexadecimal digits are needed if 64-bit WEP is used; 26 Hexadecimal digits are needed if 128-bit WEP is used; 58 Hexadecimal digits are needed if 256-bit WEP is used. For example,[...]