Chrysler Sebring Convertible (2004) manual

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................ 4 5 4 UNDERST ANDING YOUR INSTRUMENT P ANEL .................................. 7 9 5[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION CONTENTS m Introduction ........................... 4 m How T o Use This Manual ................. 4 m W arnings And Cautions .................. 6 m V ehicle Identification Number .............. 6 m V ehicle Modifications / Alterations .......... 6 1 I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

INTRODUCTION 5 1 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. VEHICLE ID[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys ................. 9 ▫ Ignition Key Removal ................... 9 ▫ Automatic T ransaxle Ignition Interlock System . .10 ▫ Key-In-Ignition Reminder ................ 1 0 m Sentry Key — If Equipped ................ 1 0 ▫ Replacement Keys ...................... [...]

▫ General Information .................... 1 8 ▫ T ransmitter Battery Service ............... 1 8 m V ehicle Theft Alarm ..................... 1 9 ▫ T amper Alert ......................... 1 9 ▫ Security System Manual Override ........... 2 0 m T runk Lock And Release .................. 2 0 m T runk Safety W arning .................... 2 0 [...]

A WORD ABOUT YOUR KEYS CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition, lock the doors, and close the windows when leaving the vehicle unat- tended. Ignition Key Removal Place the shift lever in P ARK and make sure that the gearshift knob push button has returned to the out position. T urn the key to th[...]

inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Automatic T ransaxle Ignition Interlock System This system pr events the key fr om being removed unless the shift lever is in P ARK. It also prevents shifting out of P ARK unless the key is in the OFF or RUN positions. Key-In-Ignition Reminder [...]

immobilized. If the Theft Alarm Light remains On during vehicle operation, it indicates a fault in the system electronics. All of the keys pr ovided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sen[...]

General Information The Sentry Key system complies with FCC rules part 15. Operation is subject to the following two conditions: 1. this device may not cause harmful interference 2. this device must accept any interference that may be received, including interference that may cause undes- ired operation ILLUMINA TED ENTRY SYSTEM The interior lights[...]

Power Door Locks There is a door lock switch on each front door located to the front of each door handle. Press this switch to lock or unlock the doors. If you pr ess the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. If the door lock plunger is down when you shut the door , the[...]

Door Ajar W arning If you move the vehicle and a door is not completely closed, the word DOOR will replace the odometer dis- play and a chime will sound once. The odometer display will reappear once the door is closed. Automatic (Rolling) Door Locks The doors will lock automatically , as programmed from the factory , if: 1. The transaxle is in gear[...]

3. Depr ess the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming. Automatic Unlock on Exit—Only A vailable if Automatic Door Locks are Enabled This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK position. This function is diable[...]

T o unlock the doors: Press and r elease the UNLOCK button once to unlock the driver’s door . Press the button twice within 5 seconds to unlock all doors. If your vehicle is equipped with Illumi- nated Entry , the interior lights also come on and remain on for about 30 seconds, when you unlock the doors. NOTE: The system may be programmed to unlo[...]

T o unlock the trunk: Press and hold the T runk button on the transmitter to unlatch the trunk. NOTE: The transmitter can be programmed to unlatch the trunk immediately upon activation of the T runk button (without pr essing and holding) by performing the following procedure: 1. Pr ess and hold the Unlock button on the transmit- ter . 2. Continue t[...]

3. Pr ess and release the Lock and Unlock buttons simul- taneously , followed by a press and r elease of ANY button on each new transmitter to be programmed as well as the original transmitter . Y ou will hear a chime when a transmitter has been successfully programmed. Y ou will have 30 seconds to finish programming all new transmit- ters. A chime[...]

2. Remove and replace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery , clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. VEHICLE THEFT ALARM The system monitors the doors, trunk, and igni[...]

Security System Manual Override The system will not arm if you lock the doors using the manual lock control. TRUNK LOCK AND RELEASE Use the key or the Remote Keyless Entry T ransmitter to open the trunk from outside the vehicle. From inside the car the trunk lid can be released by turning the ignition ON and depressing the T runk Release Button loc[...]

T runk Internal Emergency Release NOTE: As a security measure, a T runk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. See picture. POWER WIND[...]

Wind Buffeting W ind buffeting can be described as the per ception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or in certain open or partially open positions. This is a normal occurrence and can be mini- mized. If the buf feting occurs with the r ear windows open, [...]

Lap/Shoulder Belts All seating positions in your vehicle are equipped with Lap/Shoulder Belts. The belt webbing retractor is designed to lock during very sudden stops or impacts. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce your risk of striking [...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the front seat. 2. The seat belt latch plate is on the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap. 3. When the belt is long enough t[...]

W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing [...]

W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the [...]

The pretensioners are triggered by the front airbag con- trol module (see Airbag Section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and preten- sioners, both must be replaced. Enhanced Driver Seat Belt Reminder System (BeltAlert) If the driver’s seat belt has not[...]

4. T urn off the engine. A single chime will sound to signify that you have successfully completed the pr o- gramming. The Enhanced W arning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced W arning System (BeltAlert) has been deactivated, the Seat Belt W arning Light will continue to illuminate while[...]

Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has fr ont airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel. The passenger’s fr ont airbag is mounted in the instrument panel, above the [...]

the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly . Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Childr en 12 years old and under should ride buckled up in the rear seat. Infants in rear-facing child restraints should NEVER ride in [...]

Airbag System Components The front airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting W iring • Knee Impact Bolsters How The Airbag System W orks • The fr ont airbag contr ol module determines [...]

• The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously . W ARNING! Ignoring the AIRBAG light in your instrument panel could m[...]

If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and right front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or g[...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right [...]

Children 12 years and under should ride properly buck- led up in a rear seat. According to crash statistics, children are safer when properly restrained in the rear seat rather than in the front. W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on [...]

W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat. A rearward [...]

than one year . These child seats are also held in the vehicle by the lap/shoulder belt or the LA TCH child restraint anchorage system. (See the LA TCH — Child Seat Anchorage System Section.) The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly [...]

connection to the top tether anchorages have been avail- able for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. Y ou are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle. Both rear seating positions have low[...]

child r estraint systems will be installed as described her e. Again, carefully follow the installation instructions that were provided with the child restraint system. The rear seat lower anchorages are r ound bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to instal[...]

Installing Child Restraints Using the V ehicle Seat Belts The passenger seat belts are equipped with cinching latch plates which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latc[...]

3. Attach the tether strap hook (A) of the child r estraint to the anchor and remove slack in the tether strap (B) according to the child restraint manufacturer’s instruc- tions. W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the ch[...]

ENGINE BREAK-IN RECOMMENDA TIONS The engine in your new vehicle does not requir e a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contr[...]

must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. Safety Checks Y ou Should Make Inside the V ehicle Seat Belts Inspect the belt system periodically , checking for cuts, frays and loose parts. Damaged parts must be replaced immediately . Do not disassemble [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Convertible T op Operation ................ 4 7 ▫ T o Lower The T op ...................... 4 7 ▫ T o Raise The T op ...................... 4 9 ▫ T op Cover Installation ................... 5 0 ▫ T op Cover Removal ..................... 5 4 m Console Features ....................... 5 [...]

▫ Interior Lights ........................ 6 4 ▫ Multi-Function Control Lever .............. 6 6 ▫ Headlights, Parking Lights, Instrument Panel Lights .............................. 6 6 ▫ Daytime Running Lights (Canada Only) ...... 6 6 ▫ Lights-On Reminder .................... 6 7 ▫ Fog Lights — If Equipped ................ 6 7 ▫ T [...]

CONVERTIBLE TOP OPERA TION W ARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertibl[...]

3. Release the top from the windshield header by pulling both latch handles r earward until the latch hooks are fr ee. 4. Pr ess the Power T op Switch to disengage the top pins from the header . As soon as the top is free, close both latch handles. NOTE: The Power T op Switch has two detent positions for lowering the convertible top. Pressing and h[...]

T o Raise The T op: CAUTION! T o insure no damage occurs to the visors, they should be rotated to the forward (against glass) position prior to raising or lowering the convertible top. NOTE: T o avoid damage to the convertible top or its components, your vehicle is equipped with a featur e that prevents convertible top operation at speeds over 10 m[...]

T op Cover Installation W ith the top down and the convertible top latch handles in the closed position, there are two ways to install the convertible top cover . Lay the unfolded convertible top cover across the convertible top and choose the way that suits you best. Installation From Inside The V ehicle 1. Kneel on the rear seat and tuck the rear[...]

2. Insert both tabs located on the fr ont of the top cover in between the seatback and seatback bracket. 3. Snap the top cover flaps to the inner trim panel snaps. The side of the seat back cushion hides the snap. UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 51 3 I n f o r m a t i o n P r o v i d e d b y :[...]

4. Pr ess down on the forwar d portion of the top cover to engage the hook and loop fasteners. Installation From Outside The V ehicle 1. Start on one side of the vehicle and tuck as much of the top cover as possible under the black molding. 52 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

2. Snap the top cover flap to the inner trim panel snap. (The side of the seat back cushion hides the snap.) 3. T uck the top cover tab closest to you into the space between the seatback and the seatback bracket. 4. W alk to the other side of the vehicle and finish tucking the top cover under the black molding. Insert the remain- ing tab between th[...]

5. Snap the remaining top cover flap to the inner trim panel snap. 6. Pr ess down on the forwar d portion of the top cover to engage the hook and loop fasteners. T op Cover Removal Unsnap the snaps and disengage the hook and loop fasteners, slide the tabs from the rear seat and then from the rear of the top storage area. Remove the top cover , fold[...]

CONSOLE FEA TURES The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder . The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover . The bottom of the console bin also has built in holders for compact discs or cassette tapes. T[...]

MIRRORS Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window . A two point pivot system allows for horizontal and vertical mirror adjustment. If the driver’s sunvisor interferes with the mirror , the mirr or can be moved to the right to eliminate the interference. Annoying headlight glare can be [...]

Exterior Mirrors Folding Feature — If Equipped Both mirrors have hinges and can be folded either forward or rearward to resist damage. Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel located to the left of the steering wheel. NOTE: Place the mirror selector s[...]

Illuminated V anity Mirrors An illuminated vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upward. The lights will turn on automati- cally . Closing the mirror cover turns off the lights. SEA TS Manual Front Seat Adjustments Forward/Rearward — If Equipped The adjusting bar is at the f[...]

Reclining Bucket Seats The recliner control is on the side of the seat. T o recline, lean forward slightly before lifting the lever , then lean back to the desir ed position and release the lever . T o return the seat to the upright position, lean forward slightly before lifting the lever , then lean forward to the desired position and release the [...]

Power Driver’s Seat The power seat switches are on the outboard side of the seat, near the floor . Use the forward switch to move the front of the seat cushion up and down. Use the rear switch to move the r ear of the seat cushion up and down. The middle switch will move either the entire seat forward and rearwar d or the seat cushion up and down[...]

The left rotary switch controls the heat level for the driver’s seat, and the right r otary switch controls the heat level for the passenger’s seat. These switches feature several heat settings ranging from 0 to 6. T o Fold The Front Seatback Forward: T urn the high mounted release lever rearwar d and fold the seatback forward. If you r elease [...]

Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact fr om the rear . Adjust the restraints so that the upper edge is as high as practical. T o raise, pull up on the head restraint. T o lower , depress the button on the post guide and push down on the head restraint. TO OPEN AND CLOSE THE HOOD T o[...]

Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop” on the underside of the hood. T o prevent possible damage, do not slam the hood to close it. Use a firm downward [...]

LIGHTS Front Map/Reading Lights These lights, located under the rearview mirr or , come on whenever a door is opened or the illuminated entry system is activated. The lights can also be turned on with the doors closed by means of switches located on the front of the rearview mirror . NOTE: The map lights will remain on until the mirror switches hav[...]

turn on the lights. T urn the panel dimmer switch fully clockwise to prevent the lights from coming on when a door is opened. NOTE: The interior lights have a “fade to off” feature. When the lights are turned off, they gradually “fade” off. Dimmer Control W ith the parking lights or headlights on, rotating the dimmer contr ol for the interi[...]

Multi-Function Control Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, passing light, dome light, and fog lights. Headlights, Parking Lights, Instrument Panel Lights T urn the end of the control lever to the first detent for parking light operation.[...]

until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights ar e on after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The fog light switch is in the mu[...]

WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch in the right side control lever . T urn the end of the control lever to select the desired wiper speed. NOTE: Always remove any build-up of snow that prevents the windshield wiper blades from returning to the OFF position. If the windshield wiper switch is turned OFF and[...]

Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. T urn the lever to the delay position, then select the delay interval. The delay can be regulated from a maximum of appr oximately 18 seconds between cycles, to a cycle every 1/2[...]

TRACTION CONTROL— IF EQUIPPED T o turn the T raction Control System Off, press the switch located on the top of the steering column, to the right of the hazard switch, until the T raction Contr ol indicator in the instrument cluster lights up. T o turn the T raction Control System On, press the switch until the T raction Control indicator in the [...]

T o Activate: Press the ON/OFF switch to turn the speed control system ON. T o turn the system OFF , press the ON/OFF switch again. The system should be turned OFF when not in use. The CRUISE Indicator in the instrument cluster will light up when the Speed Control is ON. NOTE: Y ou must press the ON button to activate the system each time the engin[...]

T o decrease speed while speed control is Engaged, press and hold the COAST button. Releasing the button when the desired speed is reached, will establish a new SET speed. T apping the COAST button once will result i na1m p h (1.6 km/h) decrease in the SET speed. Each time the button is tapped, the SET speed decreases. For example, tapping the butt[...]

Rolling Hills The transaxle may downshift into third gear and remain there as the vehicle travels over rolling hills. The trans- axle will upshift into fourth gear when the road flattens out. The transaxle will r esume its normal shift schedule if you depress the accelerator pedal during any of the above conditions. W ARNING! Speed Control can be d[...]

W ARNING! A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety stan- dards. This includes most garage door opener mod- els manufactured after [...]

3. Choose one of the thr ee Universal T ransceiver buttons to program. Place the hand held controller one to three inches from the Universal T ransceiver while keeping its indicator light in view . 4. Using both hands, press the hand held transmitter button and the desired Universal T ransceiver button. Do not release the buttons until step 5 has b[...]

On garage door openers with the “Rolling Code” featur e, the transmitter code changes after each use to pr event the copying of your code. T o check if your device is protected by a “Rolling Code” system: • Check the owner’s manual for the device for mention of “Rolling Codes”. • Press and hold the programmed button on the Univer [...]

Canadian Programming/Gate Programming Canadian frequency laws, and the technology of some entry gates, require you to press and release the hand held transmitter button every two seconds during pro- gramming Continue to pr ess and hold the Universal T ransceiver button while you press and release the hand held trans- mitter button until the fr eque[...]

1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesir ed operation. NOTE: Changes or modifications not expr essly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink t is a t[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instruments And Controls ................. 8 3 m Instrument Cluster Standard ............... 8 4 m Instrument Cluster Premium ............... 8 5 m Instrument Cluster – GTC Model ........... 8 6 m Instrument Cluster Description ............. 8 7 m Compass, T emperature, And T rip Computer Display ?[...]

▫ Seek Button (Radio Mode) ................ 9 8 ▫ T uning .............................. 9 8 ▫ PTY (Program T ype) Button ............... 9 8 ▫ Balance ............................. 9 9 ▫ Fade ............................... 9 9 ▫ T one Control ......................... 9 9 ▫ AM/FM Selection ..................... 1 0 0 ▫ Scan Button[...]

m Sales Code RBB—AM/FM Stereo Radio W ith Cassette T ape Player And CD Changer Capability ........................... 1 0 5 ▫ Operating Instructions .................. 1 0 5 ▫ Power Button ........................ 1 0 6 ▫ Electronic V olume Control ............... 1 0 6 ▫ Seek .............................. 1 0 6 ▫ T u n e .............[...]

▫ Program Button 5 ..................... 1 1 7 ▫ T ime Button ......................... 1 1 7 ▫ Changing Modes ...................... 1 1 7 ▫ Removing Discs From The CD Changer ..... 1 1 8 ▫ CD Changer Operation W ith The Changer O f f ............................... 1 1 8 m Remote Sound System Controls — If Equipped ...................[...]

INSTRUMENTS AND CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 83 4 I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER ST ANDARD 84 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER PREMIUM UNDERST ANDING YOUR INSTRUMENT P ANEL 85 4 I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER – GTC MODEL 86 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. T raction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON. The indicator will blink during an active tract[...]

range. Before r eaching the red area (over 6,500 rpm), ease up on the accelerator to prevent engine over speed. 6. T urn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever . 7. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward t[...]

The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 1 1. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 12. T emperature Gauge The temperature gauge [...]

replacement, be sure to keep a recor d of the reading before and after the service so that the corr ect mileage can be determined. The trip odometer shows individual trip mileage. T o switch from odometer to trip odometer , press and release the T rip Odometer button. Press and release the T rip button a second time to return to the odometer . Whil[...]

The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 18. Brake System W arning Light This light monitors both the brake fluid level and the parking brake. If the light comes on, it indicates either that the parking brake is on or there is a low fluid level in the brake master cyli[...]

remain on continuously . Refer to 9 Enhanced Driver Seat Belt Reminder System (BeltAlert™) 9 in the Occu- pant Restraints section for more information. 20. Theft Alarm Light — If Equipped The light in the instrument cluster will flash rapidly for 15 seconds. This shows that the system is arming. If the light comes on but does not flash, the sys[...]

Reset The following trip conditions can be reset: • A VG ECO (changes to present fuel economy) • ODO • ET T o reset only the trip condition curr ently displayed, press and release the STEP and US/M buttons simultaneously until a chime sounds. T o reset all trip conditions, hold down the STEP and US/M buttons simultaneously (about 2 seconds) u[...]

Compass T emperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. W ARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent[...]

When the CAL indicator goes off, the compass is cali- brated and should display correct headings. V erify proper calibration by checking North (N), South (S), East (E), and W est (W). If the compass does not appear accurate, repeat the calibration procedure in another area. Compass V ariance V ariance is the differ ence between magnetic North and g[...]

Outside T emperature If the outside temperature is more than 131°F (55°C), the display will show 131°F . When the outside temperature is less than 2 40°F ( 2 40°C), the display will show 2 40°F/C. CIGAR LIGHTER/ASHTRA Y For a nominal charge your dealer can provide a “smok- er’s” package. This package consists of a cigar lighter and an a[...]

T wo T ypes of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary ... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical di[...]

Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button. T uning Press the TUNE control up or down to increase or decrease the frequency . If you pre[...]

Program T ype Radio Display Soft Rhythm and Blues Soft R&B Sports Sports T alk T alk T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash[...]

AM/FM Selection Press the AM/FM button to change fr om AM to FM. The operating mode will be displayed next to the station frequency . The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station b[...]

Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF[...]

Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. T o turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a t[...]

• If you insert a disc with the ignition ON and the radio OFF , the CD will automatically be pulled into the CD Player and the display will show the time of day . If you insert a disc with the ignition OFF , the display will show the time of day for about 5 seconds, then go out. Seek Button Press the top of the SEEK button for the next selection [...]

T o select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds. The current channel name and n[...]

Random Play (RND) Press the Random button to play the tracks on the selected disc in random or der for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very r ough r oad, the CD player may skip momentarily . Skipping will[...]

NOTE: When first learning the control functions, the user should set the controls as shown in the following list. T one Controls…As illustrated. Speaker Control…Centered. Power Button The volume contr ol/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OF[...]

Y ou may add a second station to each push-button by repeating the above procedur e with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory . The stations stored in SE[...]

Cassette Player Features W ith ignition OFF and the sound system OFF , you can eject the tape cassette by pushing the EJECT button. Y ou can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will [...]

NR (Noise Reduction) Pushing the Number 2 Pr e-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display . Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby an[...]

CD Diagnostic Indicators When driving over a very r ough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to protect your CD player , one of the following warning symbols may appear on your display . A CD HOT symbol indicates the player is too hot. [...]

SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL contr ol to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the ra[...]

Bass and T reble T one Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down in- creases or decreases amplification of that band. The mid position provides a balanced output. [...]

CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eject a disc with t[...]

Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play . Mode Press the MODE button repeatedly to select between the CD player , the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA” will appear in yo[...]

Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very r ough r oad, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically . As a safeguard and to protect your CD player , one of the fo[...]

6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3 ⁄ 4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer . Each disc has a number ed button with an amber light above it which, when illuminat[...]

Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button[...]

• Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. Removing Discs from the CD Changer If ther e is a single CD in the changer , pr ess the EJT button and the CD will eject. If the CD is not removed within 15 second[...]

Pressing the center button will make the radio switch between the various modes available (AM/FM/T APE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center . The function of the left hand control is dif ferent depending on which mode you are in. The following describes the left hand contr ol operation in each m[...]

If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc. CASSETTE T APE AND PLA YER MAINTENANCE T o keep the cassette tapes and player in good condition, take the following precautions: 1. [...]

COMP ACT DISC MAINTENANCE T o keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge or center; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not us[...]

CLIMA TE CONTROLS Manual Air Conditioning/Heater Control The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as fol[...]

NOTE: If your air conditioning performance seems lower than expected, check the fr ont of the air condition- ing condenser for an accumulation of dirt or insects. The air conditioning condenser is located in front of the radiator . Clean with a gentle water spray fr om behind the radiator and through the condenser . Fabric front fascia protectors m[...]

• Panel Air is dir ected through the outlets in the instr u- ment panel. These outlets can be adjusted to direct air flow . • Bi-Level Air is directed through the instrument panel and floor outlets. NOTE: There is a dif ference in temperatur e between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This [...]

NOTE: The defroster turns off automatically after 15 minutes of operation. Each later activation will allow 10 minutes of operation. Side Window Demisters A side window demister outlet is at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST modes[...]

Operating T ips (Manual A/C Control Only) 126 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :[...]

Outside Air Intake When operating the system during the winter months, make sure the air intake, directly in front of the wind- shield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains. UNDERST ANDING YOUR INSTRUMENT P ANEL 127 4 I n f o [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

ST ARTING AND OPERA TING CONTENTS m Starting Procedur es .................... 1 3 2 ▫ Automatic T ransaxle ................... 1 3 2 ▫ Manual T ransaxle ..................... 1 3 2 ▫ Normal Starting ...................... 1 3 2 ▫ Extreme Cold W eather (Below -20°F Or -29°C) ................. 1 3 3 ▫ If Engine Fails T o Start ...........[...]

▫ Anti-Lock Brake System (ABS) — If Equipped ........................... 1 4 2 m Power Steering ........................ 1 4 3 m T raction Control — If Equipped ........... 1 4 4 m T ire Safety Information .................. 1 4 5 ▫ T ire Markings ........................ 1 4 5 ▫ T ire Identification Number (TIN) .......... 1 4 8 ▫ T ir[...]

m T railer T owing ........................ 1 6 6 ▫ W arranty Requirements ................. 1 6 6 m Flexible Fuel – (2.7L Engines W ith Automatic T ransmission Only) ..................... 1 6 8 ▫ E-85 General Information ................ 1 6 8 ▫ Ethanol Fuel (E-85) .................... 1 6 8 ▫ Fuel Requirements .................... 1 6 8[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. W AR[...]

W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . CAUTION! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- axle cannot be started this way . Unburn[...]

If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL ST AR TING” or “EXTREME COLD WEA THER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it ther e while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! T o preven[...]

W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. AUTOMA TIC TRANSAXLE Brake/T ransmission Interlock This interlock system pr events you from moving the gear selector out of t[...]

CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, P ARK, or NEUTRAL into any forward gear[...]

Four Speed Automatic T ransaxle The electronically controlled transaxle pr ovides a precise shift schedule. The transaxle electronics are self calibrat- ing; ther efore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and preci- sion shifts will develop within a few shift cycles. Reset Mode The transaxle is[...]

W ARNING! Y our vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P . Make sure it is in Park before leaving the vehicle. W ARNING! Never use the Park position as a substitute for the parking brake.[...]

NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance, fuel economy , and extend transaxle life by reduc- ing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress. “L” Low This range should be used for maximum eng[...]

NOTE: During cold weather , until the transaxle lubri- cant has warmed, you may have difficulty shifting. This is normal and not harmful to the transaxle. Recommended Shift Speeds T o use your manual transaxle for both fuel economy and performance, it should be upshifted as listed. Shift at the vehicle speeds listed for acceleration. Earlier upshif[...]

P ARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is set. T o set the parking brake, pull up firmly on t[...]

BRAKE SYSTEM Y our vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that requir ed with the power system operating. W[...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that af forded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tu[...]

TRACTION CONTROL — IF EQUIPPED The T raction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction while spinning. The traction system oper- ates at speeds below 35 mph (56 km/h). The system is always in the “stand by” mo[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards. T ires designed to this standard have th[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards LT = Light T ruck tire based on U.S. design standards T = T emporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = Aspect Ra[...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and Tire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your v[...]

adhere to the loading conditions, tire size and cold tire inflation pressur es specified on the T ire and Loading Information placard and the V ehicle Loading section of this manual. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GA WR’s) for the front and r ear axles must not be exceeded. For further information on GA[...]

NOTE: For the following example the combined weight of occupants and cargo should never exceed 865 lbs. (392 Kg). ST ARTING AND OPERA TING 151 5 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMA TION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory opera[...]

2. Economy— Improper inflation pressur es can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also incr eases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and V ehicle Stability— P[...]

CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressur e is defined as th[...]

W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires W ARNING! Combining radial ply tires with other types of [...]

Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car w[...]

T read Wear Indicators T read wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent gr ooves, the tire [...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can cause unpredictable handling and stress to steeri[...]

TIRE CHAINS Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country requir e the use of snow tires during winter . Standard tires are of the all season type and satisfy this r equirement as indicated by the M+S designation on the tire side w[...]

Follow the r ecommended tire r otation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The suggested rotation method is the “forward-cr oss” shown in the diagram. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offe[...]

autostick lever to the AUTOSTICK position. The trans- axle will remain in the current gear until an upshift or downshift is chosen. Move the lever back to the Overdrive position to shift out of the Autostick mode. Autostick General Information • The transaxle will automatically upshift from first to second gear and fr om second to third gear when[...]

FUEL REQUIREMENTS Y our vehicle is designed to meet all emis- sion regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gaso- line will provide no benefit over high quality regular gasolines, and in some cir cu[...]

CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system com- ponents. Problems that result from using methanol/gasoline blends are not the responsibility of the manufactur er and may not be covered by the vehicle warranty . While MTBE is an oxygenate[...]

Malfunction Indicator Light to illuminate. The manufac- turer recommends that you try a differ ent brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for service. CAUTION! If the Malfunction Indicator Light is flashing, imme- diate service is required. S[...]

NOTE: T ighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secur ed. Make sur e that the gas cap is tightened each time the vehicle is refueled. NOTE: When the fuel nozzle “clicks” or shuts off, the fu[...]

VEHICLE LOADING V ehicle Loading Capacities Front Seat Occupants ....................... 2 Rear Seat Occupants ........................ 2 Luggage ...................... 1 1 5 lbs. (52 kg) Rated V ehicle Capacity ............ 7 1 5 lbs. (324 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing [...]

• The “D” range can be selected when towing. However , if frquent shifting occurs while in this range, the “3” range must be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend tranaxle life by reducing excessive shifting and heat build up. W ARNING! Co[...]

FLEXIBLE FUEL – (2.7L Engines with Automatic T ransmission Only) E-85 General Information The information in this section is for Flexible Fuel ve- hicles only . These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Un- leaded Gasoline Only . This section only covers those subjects that are unique to t[...]

• you operate the vehicle immediately after refueling for a period of at least 5 minutes Observing these precautions will avoid possible hard starting and/or significant deterioration in drivability during warm up. NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard starting and rough idle following start up even if[...]

• Engine Oil Selection for Operating on E-85 If you operate the vehicle on E-85 fuel, either full or part-time, use only Mopar Flexible Fuel 5W -30 engine oil (P/N 4318086) or an equivalent that meets the Manufacturer’s Standard MS-9214. Equivalent com- mercial Flexible Fuel engine oils may be labeled as Flexible Fuel (FFV) or Alternate Fuel (A[...]

Replacement Parts Many components in your Flexible Fuel V ehicle (FFV) ar e designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol com- patible parts. CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle and may void the warranty . Maintenance If [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flasher ................. 1 7 4 m If Y our Engine Overheats ................ 1 7 4 m Jacking And T ire Changing ............... 1 7 6 ▫ Preparations For Jacking ................ 1 7 6 m Jump-Starting The Battery ............... 1 8 1 m Driving On Slippery Surfaces ............. 1 8 4 ▫ Acce[...]

HAZARD W ARNING FLASHER The flasher switch is on top of the steering column, just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash. Depress the switch again to turn Hazard W arning Flashers off. Do not use this emer gency warning system when the vehicle is in motion. U[...]

the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off u[...]

JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a s[...]

1. Block wheel diagonally op- posite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage. WHA T TO DO IN EMERGENCIES 177 6 I n f o r m a t i o n P r o v i d e d b y :[...]

3. Befor e raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. W ARNING! T o avoid possible personal injury , handle the wheel [...]

WHA T TO DO IN EMERGENCIES 179 6 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove lug nuts and tire. 7. Mount spare tire. 8. T ighten all lug nuts on mounting studs. 9. Lower the vehicle to the ground by turning the jack handle count[...]

JUMP-ST ARTING THE BA TTER Y W ARNING! • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transaxle cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a dis- charged battery[...]

W ARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attach- ment of the vehicle with the discharged battery . Make sure you have a good contact on the engine. W ARN[...]

W ARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid[...]

DRIVING ON SLIPPER Y SURF ACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a dif ference in the surface traction under the fr ont (driving) wheels, particularly with high output engines. W ARNING! Rapid [...]

FREEING A STUCK VEHICLE If your vehicle is equipped with T raction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow , it can often be moved by a rocking motion. T urn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth bet[...]

TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic T ransaxle Y our vehicle may be towed under the following condi- tions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h). If the transaxle is not [...]

MAINT AINING YOUR VEHICLE CONTENTS m 2.4L Engine .......................... 1 8 9 m 2.7L Engine .......................... 1 9 0 m Onboard Diagnostic System — OBD II ...... 1 9 1 m Emissions Inspection And Maintenance Programs ............................ 1 9 2 m Replacement Parts ..................... 1 9 3 m Dealer Service .....................[...]

▫ Appearance Care And Protection From Corrosion ........................... 2 1 6 m Convertible T op Care ................... 2 2 1 ▫ W ashing ............................ 2 2 1 ▫ General Cleaning ..................... 2 2 1 ▫ Cloth T op Additional Cleaning Procedur e .... 2 2 2 ▫ Cloth T op Protection ................... 2 2 2 ▫ W eath[...]

2.4L ENGINE MAINT AINING YOUR VEHICLE 189 7 I n f o r m a t i o n P r o v i d e d b y :[...]

2.7L ENGINE 190 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission contr ol systems. When these systems are operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requir ement, this check verifies the following: the MIL (Malfunction Indic[...]

If your OBD system is not ready , you should see your authorized dealer or repair facility . If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that[...]

W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance ser[...]

CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32° F (0° C) • Stop[...]

NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions,we recommend engine oils that are API Certified and meet the requirements of DaimlerChrysler’s Material Standard MS-6395[...]

may be labeled as Flexible Fuel (FFV) or Alternate Fuel (AFV). These engine oils may be satisfactory if they meet the manufacturer’s standard. CAUTION! If Flexible Fuel engine oil is not used when using E-85, engine wear may be increased significantly . This may void your warranty . Synthetic Engine Oils There are a growing number of engine oils [...]

Drive Belts — Check Condition and T ension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt[...]

Catalytic Converter The catalytic converter requires the use of unleaded fuel only . Leaded gasoline will destroy the ef fectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly serviced to assure pro[...]

• Do not idle the engine with any spark plug wires disconnected for prolonged period. Engine T iming Belt Replace the engine timing belt (2.4L Only) at the intervals described in the appropriate maintenance schedule. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As [...]

W ARNING! Battery posts, terminals and related accessories con- tain lead and lead compounds. W ash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on ski[...]

through the condenser as requir ed. Fabric front fascia protectors may r educe air flow to the condenser , r educing air conditioning performance. W ARNING! The air conditioning system contains refrigerant under high pressure. T o avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnec[...]

Fluid level should be maintained at the proper level indicated on the side of the reservoir . If necessary , add fluid to restore to the proper indicated level. W ith a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type. Suspension Ball Joints There are two upper [...]

Multi-Purpose Lubricant, NLGI Grade 2, should be ap- plied sparingly to all pivot and sliding contact areas. External Lock Cylinders Lubricate the external lock cylinders twice a year , prefer- ably in the fall and spring. Apply a small amount of lubricant, such as Mopar Lock Cylinder Lubricant di- rectly into the lock cylinder (avoid excess lubric[...]

Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner . This will remove accumula- tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using [...]

W ARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system. If you notice a change in the so[...]

Cooling System Inspection W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition key to the OFF position. The fan is controlled by both the temperature of the engine cooling system and the pressure in the air conditioning system and can start at any time the ignition key is in the ON position.[...]

Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. The first change should not be requir ed until 5 years or 100,000 miles (160,000 km), whichever comes first. The coolant should be flushed and changed every two years or 36,000 miles (57,600 km) thereaf[...]

Coolant Pressure Cap The cap must be fully tightened to pr event loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. W ARNING! The warning words “DO NOT OPEN HOT” on the cooling sys[...]

over time. This is normal. If the coolant level is hard to see, jostling the coolant bottle will make it easier to see. There is no need to remove the radiator cap unless checking for coolant freeze point, adding, or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory , the coolant b[...]

ONL Y the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and V acuum/V apor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber , cracking, checking, tears, cuts, abrasions, and e[...]

Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these ar eas has not melted or collapsed. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the h[...]

Use only manufacturer’s r ecommended brake fluid, r efer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. W ARNING! Use of a brake fluid that has a lower initial boiling point than MOP AR DOT 3 Brake Fluid or that is unidentified as to DOT FMVSS specification may result in sudden brake failure during hard or pro- longed[...]

Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturers recommended transmis- sion fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescri[...]

• If the fluid is hot (180°F / 82°C), the reading should be in the cr oss hatched area marked ”HOT” (between the upper two holes in the dipstick). • If the fluid level shows low , add sufficient transmis- sion fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o preven[...]

Manual T ransaxle Use only the manufacturer’s recommended transmission fluid for the manual transaxle, NV -T350 or NV -T850, in your vehicle. Refer to Recommended Fluids, Lubricants and Genuine Parts section for corr ect fluid type. If it becomes necessary to top off or replace completely , this fluid should be used. The fill plug for the NV -T85[...]

The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone[...]

• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the responsibility of the owner . • Use Mopar touch up paint on scratches or chips as soon as possible. Y our dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an acciden[...]

Do not use cleaners, conditioners and protectants con- taining silicon or bleach as these may cause gloss level increases and/or discoloration. Y ou should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bri[...]

Plastic is not as scratch resistant as glass and therefore differ ent lens cleaning procedur es must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvent[...]

CONVERTIBLE TOP CARE Immediate r emoval of any contaminant is r ecommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier . Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. W ashing Hand washing is highly recommended. Automatic car washing equipment [...]

V acuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure r emoval of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains. If stains persist, contact your local dealership for further sugges- tions. Cloth T op Additional Cleaning Procedure For additional clean[...]

FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment, near the air cleaner . This information ap- plies to vehicles built without the fuse and relay num- bering embossed on the Power Distributuion Center T op Cover . Interior Fuses The fuse access panel is behind the end cover at the lef[...]

Cavity Fuse Circuit 1 30 Amp Green Blower Motor 2 10 Amp Red Right High Beam Headlight, High Beam Indicator 3 10 Amp Red Left High Beam Headlight 4 15 Amp Blue Power Door Lock Switch Illu- mination, Power T op Switch, T ransmission Range Switch, Daytime Running Light Mod- ule (Canada), Power W in- dows, Anti-lock Brake Sys- tem Module 5 10 Amp Red [...]

CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow , it shows a problem in the circuit that must be corrected. REPLACEMENT LIGHT BULBS LIGHT B[...]

BULB REPLACEMENT Headlight Bulb Replacement 1. Open the hood and remove the two headlight mount- ing screws. 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. 226 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

3. Gently pry the headlight assembly away from the fender as shown in the pictur e. This will free the ball stud from its retainer in the fender . Pull the headlight assem- bly away from the vehicle. 4. T urn the retaining ring counterclockwise and remove the bulb and socket assembly . 5. Pull the bulb out of the socket and replace the bulb. CAUTIO[...]

7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 8. Reinstall the headlight assembly . Park, T urn Signal, Sidemarker Bulb Replacement 1. Open the hood and remove the two headlight assem- bly mounting screws. Pull the headlight assembly away from the vehicle. 2. Gently pry the headlight assembly awa[...]

3. T urn the bulb socket counter clockwise and remove the bulb and socket assembly . 4. Pull the bulb out of the socket, replace the bulb, and reinstall the bulb and socket to the headlight assembly . Reinstall the headlight assembly . Fog Light Bulb Replacement 1. Remove the screw securing the light assembly to the front fascia. 2. Pull the bulb a[...]

4. T urn the bulb and socket assembly counterclockwise to remove it from the housing. 5. Install the new bulb and socket assembly , reattach the wiring connector , and reinstall the fog light assembly . Center Stoplight Bulb Replacement Y ou may wish to see your dealer for service of this light. A detailed service procedur e is contained in the man[...]

2. Disconnect the wiring connector as shown and re- move the plastic retainers. Remove the light housing from the vehicle. 3. T urn the bulb socket counter clockwise to remove it from the housing. Remove the bulb and r einstall the bulb and socket assembly . 4. Reinstall the light housing and reconnect the wiring connector . Push the trunk liner ba[...]

Headlight Aiming The headlights on your new vehicle were aimed at the factory . The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may be necessary to r eadjust the headlights if carrying an excessive amount of weight in the trunk, rear seats or pulling a trailer . T o readjust the headlights[...]

RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API Certified (GF-3). Refer to oil viscosity chart for correct SAE grade. Spark Plugs Refer to the V ehicle Emission [...]

I n f o r m a t i o n P r o v i d e d b y :[...]

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ...... 2 3 6 m Maintenance Schedules .................. 2 3 6 ▫ Schedule “B” ........................ 2 3 9 ▫ Schedule “A” ........................ 2 4 6 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d b y :[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliabi[...]

• T axi, police, or delivery service (commercial ser- vice). L • Off-r oad or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5,000 km) or 3 months, whichever comes first and follow schedule B of the “Maintenance Schedules” sectio[...]

At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut of f. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading. Add oil only when the level is at or below the ADD or MIN mark. • Check the windshield washer solvent and add if requir ed.[...]

SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L . • Day or night temperatures are below 32° F (0° C)[...]

Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if necessary .* XXXXX X Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. X 240 SCHEDULE “B” 8 M A I N T E N A N C[...]

Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if re- quired.* XXX X X Replace the air cleaner filter . X Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or rep[...]

Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (62 000) (67 000) (72 000) (77 000) (82 000) (86 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if necessary .* XXXXX X Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. X 242 SCHEDULE “B” 8 M A I N T E N A[...]

Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (91 000) (96 000) (101 000) (106 000) (110 000) (115 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if necessary .* X XXX X Replace the air cleaner filter . X Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or[...]

Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter . XXXXX X Inspect the air cleaner filter and replace if necessary .* XXXXX Replace the air cleaner filter . * X Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust [...]

Miles 93,000 96,000 99,000 100,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (160 000) (163 000) (168 000) Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if necessary .* XXX X X Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. X Flush and replace the engin[...]

SCHEDULE “A” Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) (58 000) [Months] [6] [12] [18] [24] [30] [36] Change engine oil and engine oil filter . X XXXXX Inspect the air cleaner filter and replace if necessary .* X XXX X Replace the air cleaner filter . *X Replace the spark plugs on 2[...]

Miles 42,000 48,000 54,000 60,000 66,000 72,000 (Kilometers) (67 000) (77 000) (86 000) (96 000) (106 000) (1 15 000) [Months] [42] [48] [54] [60] [66] [72] Change engine oil and engine oil filter . X X XXXX Inspect the air cleaner filter and replace if requir ed.* XX X X X Replace the air cleaner filter . *X Inspect and check tension for power ste[...]

Miles 78,000 84,000 90,000 96,000 102,000 (Kilometers) (125 000) (134 000) (144 000) (154 000) (163 000) [Months] [78] [84] [90] [96] [102] Change engine oil and engine oil filter . X X X X X Inspect the air cleaner filter and replace if re- quired.* XX X X Replace the air cleaner filter . *X Inspect the front and rear brake pads, linings, ro- tors[...]

W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. SCHEDULE “A” 249 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 2 5 2 ▫ Prepar e For The Appointment ............ 2 5 2 ▫ Prepar e A List ........................ 2 5 2 ▫ Be Reasonable W ith Requests ............. 2 5 2 m If Y ou Need Assistance .................. 2 5 2 m W arran[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional char ges with the service manager . Keep a maintenance log of your vehicle’[...]

This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to r esolve the concern, you may contact t[...]

Service Contract Y ou may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will rec[...]

MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediatel[...]

• Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, pr oblem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforwa[...]

DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the National highway T raffic Safety Adminis- tration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car . All Passenger Car T ires Must Con[...]

corresponds to a level of performance which all passen- ger car tires must meet under the Federal Motor V ehicle Safety Standard No. 109. Grades B and A repr esent higher levels of performance on the laboratory test wheel than the minimum required by law . W ARNING! The temperature grade is established for a tire that is properly inflated and not o[...]

INDEX 10 I n f o r m a t i o n P r o v i d e d b y :[...]

About Y our Brakes ...................... 1 4 2 Adding Engine Coolant (Antifreeze) ......... 2 0 8 Adding Fuel .......................... 1 6 4 Aiming Headlights ...................... 2 3 2 Air Cleaner , Engine ..................... 1 9 8 Air Conditioning ....................... 1 2 2 Air Conditioning, Operating T ips ........... 1 2 6 Air Conditi[...]

Location ......................... 181,200 Belts, Drive ........................... 1 9 8 Belts, Engine .......................... 2 0 0 Body Mechanism Lubrication .............. 2 0 3 Boot, Convertible T op .................... 5 0 B-Pillar Location ....................... 1 4 9 Brake, Parking ......................... 1 4 1 Brake System .........[...]

Compact Disc Player .................. 97,102 Compact Spare T ire ..................... 1 5 5 Compass .............................. 9 2 Compass Calibration ..................... 9 4 Console ............................... 5 5 Contract, Service ....................... 2 5 4 Convertible ............................ 4 7 Convertible Boot .............[...]

Driving On Slippery Surfaces .................. 1 8 4 Electrical Outlet, Auxiliary ................. 7 8 Electronic Speed Control .................. 7 0 Emergency Brake ....................... 1 4 1 Emergency , In Case of Jacking ............................. 1 7 6 Emergency T runk Release ............... 20,21 Emission Control System Maintenance .[...]

Capacities ........................... 2 3 2 Fog Light Service ....................... 2 2 9 Fog Lights .......................... 67,229 Freeing A Stuck V ehicle .................. 1 8 5 Fuel Adding ............................. 1 6 4 Filler Cap ........................... 1 6 4 Filter .............................. 1 9 8 Gauge ...................[...]

Illuminated Entry ....................... 1 2 Immobilizer ............................ 1 0 Infant Restraint ......................... 3 5 Inside Rearview Mirror ................... 5 6 Instrument Cluster .................. 84,85,86 Instrument Panel and Controls .............. 8 3 Instrument Panel Cover .................. 2 2 0 Instrument Panel Lens[...]

Oil Pressure .......................... 9 0 Park ............................... 2 2 8 Passing ............................. 6 7 Reading ............................. 6 4 Rear Servicing ....................... 2 3 0 Seat Belt Reminder ..................... 9 1 Security Alarm ........................ 1 9 Service .......................... 225,226 Se[...]

Oil, Engine ......................... 194,232 Capacity ............................ 2 3 2 Change Interval ...................... 1 9 5 Checking ........................... 1 9 4 Disposal ............................ 1 9 7 Filter .............................. 1 9 7 Identification Logo ................. 169,196 Materials Added to ...................[...]

Recommended Fluids, Lubricants and Genuine Parts ............................... 2 3 3 Reformulated Gasoline ................... 1 6 2 Refrigerant ............................ 2 0 2 Reminder , Seat Belt ...................... 2 7 Remote Keyless Entry .................... 1 5 Remote T runk Release .................... 2 0 Replacement T ires ........[...]

Starting .............................. 1 3 2 Cold W eather ........................ 1 3 3 Engine Fails to Start ................... 1 3 4 Steering Power ........................... 143,202 T ilt Column .......................... 6 9 Steering Wheel Mounted Sound System Controls ............................ 1 1 8 Stuck, Freeing .....................[...]

T raction Control .................... 70,87,144 T railer T owing ......................... 1 6 6 Minimum Requirements ................ 1 6 6 T railer and T ongue W eight .............. 1 6 6 W arnings ........................... 1 6 6 T ransaxle ............................. 2 1 3 Additives ........................... 2 1 5 Automatic .............[...]

W indows Power .............................. 2 1 W indshield W ashers ................... 68,205 W indshield W ipers .................... 68,205 W iper Blade Replacement ................. 2 0 5 W ipers, Intermittent ...................... 6 9 INDEX 271 10 I n f o r m a t i o n P r o v i d e d b y :[...]