D-Link DPR-2000 manual

D-Link DPR-2000 WIRELESS G USB 4-PORT MULTIFUNCTION PRINT SERVER Manual Rev . 02 (June, 2009)[...]

FCC St atement This equipment has been tested a nd found to comply with the limit s for a Class B digital device, pursuant to Part 15 of t he FCC Rules. These limit s are de signed to provide reasonable prote ction against harmful interference in a re sidential installation. This equipment generate s, uses and can radiate radio frequency energy and[...]

T able of Contents D-Link DPR-2000 User Manual i T able of Content s Before Y ou Begin ...................................................................................................... 1 Package Contents: .............................................................................................. 1 System Requirement s: .....................[...]

T able of Contents D-Link DPR-2000 User Manual ii SETUP > Printer Setup .....................................................................................52 ADV ANCED > Advanced LAN ........................................................................... 57 ADV ANCED > Advanced Wireless ...............................................[...]

T able of Contents D-Link DPR-2000 User Manual iii Adding a Printer ...............................................................................................128 AppleT alk-enabled or Bonjour-enabled Printers .............................................131 Setting up AppleT alk Printing in Mac OS 9 ............................................[...]

Package Contents Before You Begin Package Contents: Y our DPR-2000 package should cont ain the following:  D-Link DPR-2000 USB 2.0 Multifunct ion Print Server  Manual and W arranty on CD  Printed Quick Installation Guide  Cat. 5 Ethernet cable If any of the above items are missing, please contact your reselle r . System Requirements: ?[...]

Introduction D-Link DPR-2000 User Manual 2 Introduction D-Link’s DPR-2000 USB M ultifunction Print Se rver provides four USB printer po rts for connection to four USB printers and/or multifunction equi pment. It allows you to share these connected d evices with a group of users on a wi red Ethernet network a s well as an IEEE 802.11 wireless netw[...]

Introduction D-Link DPR-2000 - User Manual 3 provides relief for your PC file servers and allows them to be used to their full capacity for file access or other netwo rk services. On peer-to-peer netwo rks, workstations can print directly to the Print Server without increasing the load of another workstation or server.  The DP R-2000 Print Serve[...]

Introduction D-Link DPR-2000 - User Manual 4  NetBEUI Windows NT/2000/XP, Windows 95/98 SE/ME, Windo ws for Workgroups, Microsoft LAN Manager, IBM LAN Server  AppleTalk Mac OS EtherTalk The PS software, PS Link and PS Wizard allo w further configuration of the DPR-2000: ¾ PS-Link － Use this to enable your computers to use your printers’ [...]

External Features D-Link DPR-2000 User Manual 5 External Features The DPR-2000’s USB pri nter ports are locate d on the rear panel of this Print Server and are configurable using the web conf igurator. The default IP address of the DPR-200 0 is automatically acquired from a DHCP server on the network. If a DHCP server ca nnot be fo und, use the d[...]

External Features Reset Button 4 USB Printer Ports Ethernet LAN Port Power Socket USB Printer Ports (1 to 4) Each of the four USB 2.0 printer port s can be connected to a USB printer or USB multifunction printer . Ethernet LAN Port This port connect s to an Ethernet LAN port of a switch or a router , using a Cat 5 Ethernet cable. This port supports[...]

External Features LED Indicators All LED indicators are on the top side of the Print Server .  Power A steady blue light confirms that the Print Server is turned ON.  USB 1 to 4 A steady blue light for each of the four U SB ports indicates the printer co nnected to a particular USB port is online and succes sfully connected to the Print Serve[...]

External Features D-Link DPR-2000 - User Manual 8  Wireless LAN Link/Act A steady blue light confirms that the Print Server has a wireless connection to your wireless network. This light will also blin k when the Print Server is receiving or transmitting wireless dat a on the network. All LED indicators described above are also use d during the [...]

Setting up the DPR-2000 Setting up the DPR-2000 Installing the Print Server WA R N I N G : - Configuration problem s may result if you power ON the Print Server without first establishing it s network conne ction. - Use power adapter suppl ied with this Print Server to conne ct to an AC source. Using a power adapter with an incorrect power rating w[...]

Setting up the DPR-2000 D-Link DPR-2000 - User Manual 10 Check your D-Link web site for the lasted updated list. This section will describe the inst allation step s for a wired Ethernet connection. Follow the steps below to avoid any complic ations during the h ardware installation: 1. Confirm that all the printers that y ou will connect to the DPR[...]

Setting up the DPR-2000 D-Link DPR-2000 - User Manual 11 Immediately after powe r-up, all LEDs shoul d illuminate steadily for several se conds. Then the USB LEDs should turn OFF si multane ou sly . Irregularity of any of the LEDs during these LED test s may mean there is a problem with the LEDs them selves. The actual component test s immediately [...]

Using the PS Software D-Link DPR-2000 User Manual 12 Using the PS Software Auto-Run Installation Insert the included installation CD into your computer’ s CD-ROM drive to initiate the auto-run program. If auto- run does not start, click My Computer > [ CD ROM Dri ve Letter ]. The content of the installation CD-ROM include s: • Install PS Sof[...]

Using the PS Software PS Software To avoid any conflict with in your network, use the PS Software to change your Print Server’s settings, such as its IP addre ss. The PS Software contains two utilities, namely the PS-Link and the PS-Wizard . Installing PS Software 1. Click the Next > button in the welcome window of the InstallShield Wizard . 2[...]

Using the PS Software 3. You may enter a new folder name in the Program Folder field if you want to change the default name. Otherwise cli ck the Next > button to go to the next screen. D-Link DPR-2000 - User Manual 14 4. The InstallShield Wizard starts to install the software, and the Progress bar indicates the installation is pro ceeding until[...]

Using the PS Software Using PS-Link PS-Link (for Windows 2000/XP/2003/V ist a) is a utility that will help you install yo ur printers’ man ufacturer drivers. Using the Link command you can simulate a physical USB connection between your computer and a printe r , thus enabling you to complete the install ation of the manufacturer drivers without m[...]

Using the PS Software Ser ver Name : This list displays the names of all print servers wit hin the network. Discover : Click this button to search for more print servers. Status Bar : The status bar at the bottom of the screen displays the current system status and number of connecte d print servers. Information : This field displays the basic info[...]

Using the PS Software Click Next > to begin configuring the set tings. System Settings Enter the Server Name, Port Name a nd Password for your Print Server. Click Next > to continue to the next page, or Cancel to exit. D-Link DPR-2000 - User Manual 17[...]

Using the PS Software Changing the IP Address: Select Manua lly Assign to enter a specifi c IP address for your Print Server, or DHCP Assign Automaticall y to have an IP address automatically assigned to your Print Server. C l i c k Ne xt > to continue to the next page, or Cancel to exit. Microsoft Network Workgroup Type the name of the Microsof[...]

Using the PS Software D-Link DPR-2000 - User Manual 19 AppleTalk Settings (Optional) Enter the AppleTalk Zon e or just type “*” if your Apple Talk network is not divided into zones. Type the Printer Type. Click Next > to continue to the next page or Cancel to exit.[...]

Using the PS Software After the configuration of these scre ens is complete, click Sav e to store the settings that are displayed, or Cancel to abort. You can also click < Back to modify these settings. [Change IP Address ] - Click this button to bring up the follo wing screen. This screen allows you to change the IP Addres s of the Print S e r [...]

Using the PS Software [Web Setup ] – Click this button to launch the web configurato r . Y ou can also launch the web configurator by clicki ng on the nam e of the server in the Device List. Printer Port : This field displays the basic information and the curre nt status of the connected printers. It also allows you to use the four control button[...]

Using the PS Software D-Link DPR-2000 - User Manual 22 Installing and Using a Multifunction Printer Multifunction/GDI Printer This section will tell you how to use a multifunction or GDI printer through the PS-Link utility after the printer manufactu re r ’s driver ha s already been inst alled. For PCs with the multifunction/GD I printer driv er [...]

Using the PS Software For HP: 1. When the install ation program asks you to connect the USB cable, you are allowed to connect it later by checki ng a box. Click the Next > button to continue the installatio n. 2. When the install ation of all driver s has been co mpleted, you may use the PS-Link utility to complete the physical conn ection betwe[...]

Using the PS Software If the connection is successfully est ablis hed, the following message will be di splayed. Press OK to exit. 3. Now the MUTIFUNCTION/GDI printer is ready for use from your computer . D-Link DPR-2000 - User Manual 24[...]

Using the PS Software For EPSON: 1. When the install ation program asks you to connect the USB cable of the MUTIFUNCTION/GDI printer to your co mputer , do ignore thi s prompt message. Use PS-Link to simulate a USB con nection between your printer and comp uter . 2. T o do this, launch the PS-Link utility and click the Link button. D-Link DPR-2000 [...]

Using the PS Software When the connection is su ccessfully es tablished, the following message will be displayed. Press OK to exit. 3. Continue with the installation of the MUTIFUNCTION/GDI printer by inserting t he CD-ROM in your computer and proc eed with the remaining ste ps. 4. When the install ation is completed, you may st art to use the mult[...]

Using the PS Software For Canon: 1. When the install ation program asks you to connect the USB cable of the MUTIFUNCTION/GDI print er to your comput er , do not ignore this prompt message. Use PS-Link to simulate a USB con nection between your printer and comp uter . 2. Launch the PS-Link utility and click the Link button. D-Link DPR-2000 - User Ma[...]

Using the PS Software When the connection is su ccessfully est ablished, the following message will appear . Press OK to exit. 3. Continue with the installation of the MUTIFUNCTION/GDI printer by inserting t he CD-ROM in your computer and proc eed with the remaining ste ps. 4. When the install ation is completed, you may st art to use the multiple [...]

Using the PS Software For Lexmark: 1. When the install ation program asks you to connect the USB cable of the MUTIFUNCTION/GDI print er to your comput er , do not ignore this prompt message. Use PS-Link to simulate a USB con nection between your printer and comp uter . 2. Launch the PS-Link utility and click the Link button. D-Link DPR-2000 - User [...]

Using the PS Software When the connection is su ccessfully es tablished, the following message will be displayed. Press OK to exit. 3. Continue with the installation of the MUTIFUNCTION/GDI printer by inserting t he CD-ROM in your computer and proc eed with the remaining ste ps. 4. When the install ation is completed, you may st art to use the mult[...]

Using the PS Software For Samsung: 1. When the install ation program asks you to connect the printer to your comput er , just ignore it and click the Next> button to continue. 2. The progra m will prompt you again to connect the two devices, click No and continue with the rest of the inst allation. D-Link DPR-2000 - User Manual 31[...]

Using the PS Software 3. When the install ation of the MUTIFUNCT ION/G DI printer CD is finished, you may use PS-Link to complete the physical connection b etween the MUTIFUNCTION/GDI printer and you r computer . Click the Link button in the PS-Link window below . When the connection is su ccessful est ablished, t he following message will be displ[...]

Using the PS Software For Brother: 1. When the install ation program asks you to connect the USB cable of the MUTIFUNCTION/GDI print er to your comput er , do not ignore this prompt message. Use PS-Link to simulate a USB con nection between your printer and comp uter . 2. Launch the PS-Link utility and click the Link button. D-Link DPR-2000 - User [...]

Using the PS Software When the connection is su ccessfully es tablished, the following message will be displayed. Press OK to exit. 3. Continue with the installation of the multifunction/GD I printer by inserting the CD-ROM in your computer and proc eed with the remaining ste ps. 4. When the install ation is completed, you may st art to use the mul[...]

Using the PS Software For Fuji Xerox: 1. The installation prog ram of the Xerox mu ltifunction/GDI printer will not request you to make a physical connec tion between the printer an d your computer . 2. When the install ation is finished, you will have to est ablish a link between the MUTIFUNCTION/GDI print er and your comput er in order to use the[...]

Using the PS Software 3. Now the multifunction/GDI printer is ready to use from your computer . D-Link DPR-2000 - User Manual 36[...]

Using the PS Software Using PS-Wizard PS-Wizard (Windows 2000/XP/2003/ V ista) is a simple and useful tool for you to easily add a printer onto your computer without any complex configuration. The PS-Wizard also allows you to change the IP address settings for the Print Server , including its IP address, Subnet Mask address and default Gat eway add[...]

Using the PS Software Print Ser ver : This field allows you to manually discover any con nected print servers and to further configure a select ed print server . LAN : Here you can select to use a Dynamic IP (DHCP) or a stati c IP address for the selected Print Server . Click Apply button to implement the new settings. Port Information : This is th[...]

Using the PS Software The wizard provides three ways fo r you to select a printer driver: 1. Show currently inst alled driv ers: Select this option to see if your printer so ftware is al ready installed . If not, you may try the next method. After selecting a printer driver , click the Next> button to continue. 2. Select from manufacturer list: [...]

Using the PS Software The wizard will ask you to confirm your selection in the next pop-up window . Here, you are allowed to edit the Printer Name in the Network Printer Name field, and to enable this printer as the d efault printer by checking Use this printer as the de fault printer for Windo ws-based programs box. V erify the configuration, then[...]

Using the PS Software D-Link DPR-2000 - User Manual 41 When the following wi ndow appears, cli ck Print T est Page to perform a printing test. If everything operates as normal, click Finish to exit. If the test failed, check to see if the driver p rogram is correct, the printer is p owered d connected, and the Print Serv er is up and running on the[...]

Using the W eb Configurator D-Link DPR-2000 User Manual 42 Using the Web Configurator HOME T o begin managing your DPR-2000, make sure it has been po wered ON and connected to your network. There are three possible ways to access the DPR-2000’ s web configurator:  Launch your browser and go to the following URL address, then type in the follow[...]

Using the W eb Configurator Your computer should then displ ay the followi ng main screen of your Print Server’s web configurator. On this screen, in ad dition to product information, there are five links on the top of the main screen: Setup , Advanced, Maintenance , Status , and Help . Clicking a link from the bar will display its subm enu. Sele[...]

Using the W eb Configurator SETUP > Print Server Setup The Print Server Setup screen allows you to modify the Print Server Name and the Port Name, Description and PJL Printer selection of each of the printers connected to your DPR-2000. Do not change these settings unless you a re asked to do so by your network administrator . Print Server Name [...]

Using the W eb Configurator SETUP > LAN SETUP The LAN Setup screen allows you co nfigure your Print Server ’s lo cal network settings. Please note that this section is optional and you norm ally do not need to change any of the settings here to get your Print Serve r up and running. TCP/IP This screen allows you to automatically or manually as[...]

Using the W eb Configurator SETUP > Wireless Setup This section tells you how to configure y our Print Server so it can connect to your wireless LAN via an 802.1 1 wireless router or access point. Conne ction from wireless users (computers) to your Print Server is thro ugh this wirel ess router or access point. The WIRELESS SETUP screen is divid[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 47 1. For Connection Mode , select Infra structure . 2. The SSID is the ID name of the wireless net work that you wish your Print Server to belong to. Leave this SSID as default if your wireless network alre ady has a default SSID set up in wireless routers a nd/or a ccess point s. Otherwise[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 48 Disabling Wireless Dat a Encryption Print, fax and scanned files travelling in the air can be protected if you enable wireless dat a encryption. If you disable th is encryption, the only benefit is wireless data will travel faster between your computer s and your Print Server . If you wis[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 49 Format field. 4. T ype in four encryption keys. These keys will be used as options. 5. For Encrypt Data T ransmission Using , select one of the four key s that you typed in step 4 above. 6. For Authentication T ype , sele ct Open Sy stem , Shared Key , or Both . 7. Click Apply Settings to[...]

Using the W eb Configurator of a wireless network. Without WPS, you would have to manually set a wireless network name (SSID) and a security key that match those set in the router or access point. With WPS, you don’t need to do these settings if your router or acce ss point also support s WPS. If you have already crea ted a security profile (with[...]

Using the W eb Configurator 5.If your router or access point has a W PS button, press and hold this button a few seconds, then release it. Otherwise, ru n the WPS program inside the router or access point. The router or access point will st art broadcasting the wireless settings in its profile for the Print Server to apply . 6. Within seconds af te[...]

Using the W eb Configurator SETUP > Printer Setup T o be able to use the printers connected to the Print Server , users must have the driver programs of the printers in stalled in their comput ers. While these programs are provided by the printers’ manufactu r ers, some of these programs are also included in the Microsoft Windo ws network oper[...]

Using the W eb Configurator 4.Click Run to execute the Windo ws Wizard program. If a security warning appe ars click Run again. 5.The screen will display all the printers currently connected to the Print Server . Each printer ’s information i s displayed in one row , which includes the printer ’s name (such as HP La serJet 2000), the Print Serv[...]

Using the W eb Configurator 6. The Windo ws Wizard program provides three options for you to sele ct a driver program for the targ et printer that you selected in step 5: a. Show currently inst alled driv ers: Select this option to list out all printer dr iver programs previously installed in the user ’s comp uter , under the Installed Printer Dr[...]

Using the W eb Configurator c. Have Disk: Select this option if you have on hands the driv er program of the t arget printer . Click the Have Disk button to bring up the followin g window . Insert the manufacturer ’s installation CD to inst all the printer driver . Click OK to c ontinue. 7. After you have selected the printer driv er , the wizard[...]

Using the W eb Configurator 8. After you have completed the ve rification and configuration, click Next > to continue. The printer (in this case the HP Laser Jet 2000) will be automatically created in the Windows’ Printers and Faxes screen. When the following screen displ ays, you c an perform a print test by clicking the Print Te s t P a g e [...]

Using the W eb Configurator ADVANCED > Advanced LAN The Advanced LAN screen allows you to chang e more advanced network settings for your Print Server . It’s recommended t hat you do no t change these settings unless instructed to do so by your network administrato r . The Advanced LAN screen contain s three sections: TCP/IP , Microsoft Networ[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 58 of on-line printers and fax machines.  Mac Bonjour/Rendezv ous : This option allows you to enable o r disable Mac rinting function through the Internet. Microsof t Net work  Workgroup : This is the name of the workgroup that you want your Print Server to be associated with. AppleT a[...]

Using the W eb Configurator ADVANCED > Advanced Wireless The Advanced Wireless scree n allows you to change the wireless settings of your infrastructure network, whe re all wirele ss signals are transferred through a wireless router or access point. Note that y ou should not change these settings unle ss instructed to do so by your network admin[...]

Using the W eb Configurator ADVANCED > User Access The User Access screen allows you to cre ate and maintain an aut horized list of users that you allow to access the Print Server . User Access st (show Serve new s gs to store the new settings in the Print Server . T o list displayed in the section labeled AUTHORIZED USERS on the screen. Authori[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 61 T o add a user to the User List, do as follows: 1. T ype in the name of the user in the PC Description field. This name can be the 2. T ype in the MAC add ress of the computer ’s Ethernet interface. Note that this computer does not have to be actually co nnected to the network (on-line)[...]

Using the W eb Configurator ADV ANCED > E-Mail Notification The Print Server can notify you of events that happen to it and the printers by e- and print th mail, ese events on the printer . T o enable this function, go the E-Mail Notification screen below: Enable E-mail Notification Y ou can set the Print Server to send a message to your e-mail [...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 63 This screen section cont ains the field s detailing your noti  Print Server E-mail Address : This is the address w fication e-mail account. here you wish to receive is full, a message will be generated by the network administrator and sent to this Print Server email address.  Incomi[...]

Using the W eb Configurator ADVANCED > SNMP This Print Server has a limited number of SNMP (Simple Net work Management Protocol) MIBs built into it. These MIBs (Management Information Base ) allo Printer Server to be integrated in an SNMP-based manageable ne twork, which might include more complex network devices such as SNMP-ma w your naged swi[...]

Using the W eb Configurator 5. Select an Access Right for tha 6. Click Apply Setting to save the setting t Community Name. s in the Print Server. To abort and exit s Admin, and its Password is blank. r Name and Password are used to access the user interface of the Print The Pass word screen below allows you to change th without saving, click Cancel[...]

Using the W eb Configurator MAINTENANCE > Save/Restore Settings ows you to do three things: - Save the current configuration settings inside your Print Server to your computer ’s di sk drive, - Load configuration settings that you previously saved from a computer drive to The Save/Restore Settings screen all your Print Server , and - Restore t[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 67 2. Click Save . Y ou will be prompted for the target path where you wis Printer Server ’s settings. Select the t a rget folder or the drive. Then h to hold the click Save to ettings that you previously saved to your computer dr ive, rget path or cli ck the Browse button to browse. 2. Cl[...]

Using the W eb Configurator MAINTENANCE > Firmware Upgrade Y our Print Server can be upgraded with new firmware when it be comes available. ew firmware will allow you to use functi ons that a re added to your Print Server . N New firmware can be uploaded to your P rint Server via the following screen: This screen indicates the current firmware i[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 69 computer or the Print Server , or tamper with any conn ecting ca proces s. bles during the ugging it in again. 3. When the firmware uploa ding process is completed, you will be prompted in a pop-up window . Click Finish to complete and exit. 4. Reboot your Print Server by unplugging its p[...]

Using the W eb Configurator MAINTENANCE > Diagnostics ver . Y ou can do a print test for each of the printe rs that are connected to your Print Ser The Diagnostics screen bellow allows you to do this. T o print a test page, do as follows: . Click on a target printer to select. T o select a number of printers, click on all the target printers . C[...]

Using the W eb Configurator STATUS > Device Info The Device Info screen below display s the information and st atus of your Print Server , its connected printers an d its Ethernet LAN port. Thi s information is useful for troubleshooting. This scre en can be scrolled to display information that is not shown. Print Server S t atus The fields in t[...]

Using the W eb Configurator LAN St atus The fields in this section display the information relate d to the Ethernet port of the Print Server . STATUS > Network The Network screen displays the gene ral network stat us of your Print Server . Auto IP This screen sect ion shows your P rint Se rver ’s current TCP/IP settings, such as e Æ Advanced [...]

Using the W eb Configurator TCP/IP Printing D-Link DPR-2000 - User Manual 73 In this section shows the st atus of the va rious pri nting tasks th rough TCP/IP , such as the LPR printing task, the four USB print er port printing task, the IPP printing task, and the FTP printing task. Microsof t Net work Printing This screen section show s the status[...]

Using the W eb Configurator Mac AppleT alk Printing This screen se ction shows t he statu s of your printing t asks through Mac AppleT alk. STATUS >Wireless Status The Wireless S tatus screen displays the wi reless network status of the Print Serv er . D-Link DPR-2000 - User Manual 74[...]

Using the W eb Configurator STATUS >Print Log The Print Log screen displays the printi ng records of authori zed users. Printing Log The printing log displays rows of information pert aining to each au orized user . For ame of the user , the status of printi ng tasks and si ze of printing ta sks. th each row , you have the MAC address of the use[...]

Using the W eb Configurator HELP The Help screen provides help on how to use the Pri nt Server ’s functions. This screen display s a list of function topics. Click on a top to display the help information: D-Link DPR-2000 - User Manual 76[...]

Using the W eb Configurator Reboot ing the Reboot button will re-boot your Print Server . A re-boot is require d after you have made changes to the Print Server ’ s settings, so the Print Server can apply the new settings. The Reboot is located at the bottom of the lef t column of the screen. Press ait until the message disappears. Y our Print Se[...]

Using the W eb Configurator D-Link DPR-2000 - User Manual 78 Refresh Printer Status Click the printer in the left column to refresh the status of the printer .[...]

TCP/IP Printing for Windows V ist a TCP/IP Printing for Windows Vista Go to Star t Î Control Panel Î Printers . Click Add a printer . D-Link DPR-2000 User Manual 79[...]

TCP/IP Printing for Windows V ist a Select the first option, Add a local printer , and then click Next . Select the second option, Create a new po rt , and highlight St andard TCP/IP Port from the pull-down menu. Click Next . D-Link DPR-2000 - User Manual 80[...]

TCP/IP Printing for Windows V ist a In the Hostname or IP address field , type the IP address of the Print Server (e.g. 10.62.31.15), this address can be found in the PRINTER SERVER ST A T US screen of the Print Server ’s web configurator . The Port Name field will automatically fill in. Click Next . D-Link DPR-2000 - User Manual 81[...]

TCP/IP Printing for Windows V ist a In the next screen highlight the printer you wi sh to add. If the printer not on the list, click Hav e Disk and insert the printer driver disk that came with your printer to inst all the printer drivers. Click Next is D-Link DPR-2000 - User Manual 82[...]

TCP/IP Printing for Windows V ist a Click Next to start inst alling the printer . After clicking Print a test p age , a small dialogue box will display as below . Click Close . D-Link DPR-2000 - User Manual 83[...]

TCP/IP Printing for Windows V ist a D-Link DPR-2000 - User Manual 84 Click Finish . The printer is now ready for use.[...]

TCP/IP Printing for Windows V ist a D-Link DPR-2000 - User Manual 85[...]

TCP/IP Printing for Windows XP D-Link DPR-2000 User Manual 86 TCP/IP Printing for Windows XP D-Link DPR-2000 User Manual 86 TCP/IP Printing for Windows XP Go to Star t Î Printers and Faxes Î Add a Printer . When the following screen displays, click Next . Select the first option, Local printer att ached to this computer , and click Next .[...]

TCP/IP Printing for Windows XP D-Link DPR-2000 - User Manual 87 Click the second option, Create a ne w port , and sel ect St andar d TCP/IP Port from the drop-down list box. Click Next . Click Next .[...]

TCP/IP Printing for Windows XP D-Link DPR-2000 - User Manual 88 In the Hostname or IP address field, type the IP address of the Print Server (e. g. r . The Port Name field will be automatically filled in. Click Next . 10.62.31.15). This address can be found in the PRINTER SER VER ST A T US screen of the Print Server ’s web configurato[...]

TCP/IP Printing for Windows XP Select Custom and click S ettings . D-Link DPR-2000 - User Manual 89[...]

TCP/IP Printing for Windows XP The following screen will be displ ayed. Select LPR from the Protocol field. Enter the Queue Name , which can be found in the PRINTER ST A TUS screen of the Print Server ’s web configu rator . Click OK . D-Link DPR-2000 - User Manual 90[...]

TCP/IP Printing for Windows XP Click Next . D-Link DPR-2000 - User Manual 91 TCP/IP Printing for Windows XP D-Link DPR-2000 - User Manual 91 Click Next .[...]

TCP/IP Printing for Windows XP Click Finish . creen, highlight the printer you wish to ad d. If the printer is not on the list, click Hav e Disk and insert the printer driver disk that came with your printer to inst all the printer drivers. Click Next D-Link DPR-2000 - User Manual 92 In the next s[...]

TCP/IP Printing for Windows XP At this screen, you can input a name for the printer , and then click Next . Select Ye s to print a test page. Then cli ck Next . Click Finish . The pri nter is now ready for use. D-Link DPR-2000 - User Manual 93[...]

TCP/IP Printing for Windows XP D-Link DPR-2000 - User Manual 94[...]

TCP/IP Printing for Wi ndows 2000 D-Link DPR-2000 User Manual 95 TCP/IP Printing for Wi ndows 2000 D-Link DPR-2000 User Manual 95 TCP/IP Printing for Windows 2000 Go to Star t Î Settings Î Printers and Faxes Î Add a Printer . When the following screen shows u p, click Nex t . Select the first option, Local printer , and click Next .[...]

TCP/IP Printing for Wi ndows 2000 Click Next if the New Printer Detection screen pop s up. On the next screen, select the secon d option Create a new port and highlight St andard TCP/IP Port from the drop-down list. Click Next . Click Next . D-Link DPR-2000 - User Manual 96[...]

TCP/IP Printing for Wi ndows 2000 D-Link DPR-2000 - User Manual 97 In the Hostname or IP address field, type the IP address of the Print Server (e. g. reen ill be filled in automatically . Click Next . 10.62.31.15). This address can be found in the PRINTER SER VER ST A T US sc of the Print Server ’s web configurator . The Port Name field w[...]

TCP/IP Printing for Wi ndows 2000 Select Custom and click S ettings . D-Link DPR-2000 - User Manual 98[...]

TCP/IP Printing for Wi ndows 2000 The following screen will di splay , select LPR from the Protocol field. Enter the Queue Name , which can be found in the PRINTER ST A TUS screen of the Print Server ’s web configu rator . Click OK . D-Link DPR-2000 - User Manual 99[...]

TCP/IP Printing for Wi ndows 2000 Click Next . D-Link DPR-2000 - User Manual 100[...]

TCP/IP Printing for Wi ndows 2000 Click Finish . In the next screen highlight the printer you wi sh to add. If the printer i st, lick [ Have Disk ] and insert the printer driver disk that came with your printer to inter drivers. Click Next D-Link DPR-2000 - User Manual 101 s not on the li c install the pr[...]

TCP/IP Printing for Wi ndows 2000 At this screen, input a name for the printer , and then click Next >. elect the first option, Do not share this printer . Then click Next . D-Link DPR-2000 - User Manual 102 S Select Ye s to print a test page, click Next .[...]

TCP/IP Printing for Wi ndows 2000 D-Link DPR-2000 - User Manual 103 Click Finish . The pri nter is now ready for printing with Windows 20 00 on your network.[...]

TCP/IP Printing for Windows 98SE/ME TCP/IP Printing for Windows 98SE/ME Go to Star t Î Settings Î Control Panel . Double click on Network , and then click Add . D-Link DPR-2000 User Manual 104[...]

TCP/IP Printing for Windows 98SE/ME Highlight Client and click Add . D-Link DPR-2000 - User Manual 105 At this screen , click Have Disk .[...]

TCP/IP Printing for Windows 98SE/ME 1. Insert the DPR-2000 CD into your CD-R OM drive. Select the CD’s drive letter from the drop-down box. 2. Double-click on the folder lpr . 3. Select lpr .inf to highlight it. 4. Click OK . Click OK to confirm the location of the file. D-Link DPR-2000 - User Manual 106[...]

TCP/IP Printing for Windows 98SE/ME Y ou should now be back to the Netw ork Properties Page. Highlight LPR for TCP/ Printing and click Proper IP ties . D-Link DPR-2000 - User Manual 107 Click Add Port .[...]

TCP/IP Printing for Windows 98SE/ME T ype in the IP address and Port Name of the Print Server , this information can be found in the PRINTER SER VER ST A TUS and PRINTER ST A T US screens of the Print Server ’s W eb configurator . Click OK . NOTE: The IP Address and Port Name here are ju st examples only . D-Link DPR-2000 - User Manual 108[...]

TCP/IP Printing for Windows 98SE/ME The IP Address and Port Name will be displayed in the followin g screen (the IP address and port name in the screen ab ove are for example only). Click OK . D-Link DPR-2000 - User Manual 109 Click OK .[...]

TCP/IP Printing for Windows 98SE/ME Windows will ask to restart. Click Ye s . Once your computer has rebooted, click on Start Î Settings Î Printers Î Add Printer . When the Add Printer Wizard screen appea rs, click Next . Select Network Printer an d click Next . D-Link DPR-2000 - User Manual 110[...]

TCP/IP Printing for Windows 98SE/ME T ype in the path if you know it; otherwise, click Browse . From the following screen, browse for the printe r port and highlight the port (e.g. dlink-1D6F A3 in this manual). Click OK . D-Link DPR-2000 - User Manual 111[...]

TCP/IP Printing for Windows 98SE/ME If the network path is not specified, type in the IP Address and Port Name of the Print Server (like in the example below). Select Ye s or No to enable or disable printing from MS-DOS based programs. Click Next . D-Link DPR-2000 - User Manual 112[...]

TCP/IP Printing for Windows 98SE/ME Click Next In the next screen highlight the printer you wi sh to add. If the printer is not on the li st, click [ Have Disk ] and insert the printer driver disk that came with your printer to install the printer drivers. D-Link DPR-2000 - User Manual 113[...]

TCP/IP Printing for Windows 98SE/ME D-Link DPR-2000 - User Manual 114 TCP/IP Printing for Windows 98SE/ME D-Link DPR-2000 - User Manual 114 lick Next . C Select Ye s to print a test page. Click Finish .[...]

TCP/IP Printing for Windows 98SE/ME D-Link DPR-2000 - User Manual 115 T o check whether the pri nter is installe d, go to Star t Î Settings Î Printers .[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 User Manual 116 Unix/Linux Printing Printing Text Files From Unix T ext files on Unix systems contai n lines that end with “newline” characters, as opposed to MS-DOS and Wind ows-relat ed operating system s that end with a carriage return followed by a linefeed. Most printe rs requ[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 117 Printing from BSD Unix Versions m or related to the BSD SD, you can use giving a hostname for the print server’s IP address. A line in /etc/hosts contains an IP address ices protocol), you can add an add ress record entry to your DNS database for the print server. h[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 118 chown bin.daemon /var/spool/hp5l chmod 775 /var/spool/hp5l 5. Add an entry for the printer to /etc/printcap , similar to the following: hp5l: :lp=:sd=/var/spool/hp5l :mx#0: ame you created above. If backslash. 6. rt command) . name, es used above are: be blank. :rm=[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 119 ◆ sd=dir The location of the printer’s local spool di rectory. print job files in the local spool directory; =address The host whe re the remote printe r is located, in this case D-Link print server . n the remote host. e should be used. Note: this entry is case-s[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 120 Printing From SCO Unix System V/386 t. 2. int server in the host’s /etc/hosts file, giving a hostna me n IP address and on 202.39.74.40 ps-142634 ps-142634.dlink.com.tw If you use DNS (the Domain Naming Serv ices protocol), you can add an add ress record entry to yo[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 121 7. Answer r (remote printer) to the question Is printer a remote printer or a local printer (r/l)? 8. When prompted with the question: enter the name of the remote host that printer is attached 9. Is this correct? (y/n) 1 Would yo u like this to be the system default [...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 122 Printing From Solaris T o 2. n entry for the print server in the host’s file, giving a hostname for the print server’ /etc/hosts ss and on or example: 34 ps-142634.dlink.com.tw ain Naming Serv ices protocol), you can add an add ress admintool ◊ Printer Name This[...]

Setting up Printing in Mac OS X T iger (10.4.9) Printing From Red Hat Linux Adding a Printer at the bottom of the desktop. 1. Click the printer icon 2 rinter c . Since no printer is set up so far , a prompt appears asking to run the p onfiguration tool. 3. Click the OK button in the pop-up dialogue box to open the main Printer . Note that to use th[...]

Setting up Printing in Mac OS X T iger (10.4.9) Printer Configuration T ool menu 5. The Add a new print queue menu appears, clic k Forward to continue. 6. Enter a unique name for the printer in the Nam e text field. The printer name cannot cont ain sp aces and must begin with a letter . The printer n ame may cont ain letters, numbers, dashes (-), a[...]

Setting up Printing in Mac OS X T iger (10.4.9) 7. Select Networked UNIX (LPD) in the Select a queue type drop-down list, enter which the printer is att ached in the Server field, rinter . the IP addre ss of the print server to and type the port name in Queue field. Click For ward to select the type of p 8. Select the printer model. D-Link DPR-2000[...]

Setting up Printing in Mac OS X T iger (10.4.9) If a printer has not been detected automatically , select the model from the list. Y ou can manually select the na me of the printer manufacturer from the Generic (click to select manufacturer) drop-down menu, and then the printer model from the sub-l ist. Click Forward to continue. 9. The last st ep [...]

Setting up Printing in Mac OS X T iger (10.4.9) Setting up Printing in Mac OS X Tiger (10.4.9) NOTE: Mac OS printing is supported by Postscrip t printers only! With Mac OS X T iger (10.4), you can use Apple T alk, Bonjour , Internet Printing Protocol (IPP), Line Printer Daemon (LPD), and HP Jet Direct-Soc ket printing through Print Server . Click o[...]

Setting up Printing in Mac OS X T iger (10.4.9) Adding a Printer Use the Go menu at the top tool bar and open the Utilities folder . D-Link DPR-2000 - User Manual 128[...]

Setting up Printing in Mac OS X T iger (10.4.9) In the Utilities folder , find and select to see the Printer List dialog window . Click Add button to open th e Printer B rowser screen. Mac OS X T iger (10.4) supports five printing proto cols: 1. AppleT alk D-Link DPR-2000 - User Manual 129[...]

Setting up Printing in Mac OS X T iger (10.4.9) 2. Bonjour ) Daemon (LPD) 5. HP Jet Dire ct – Socket T o add an Internet Printing Protocol, Line Pr inter Daemon or HP Jet Direct – Socket enabled printer , click on the 3. Internet Printing Protocol (IPP 4. Line Printer button and follow the instructions to add an IP Printer in the “Adding an I[...]

Setting up Printing in Mac OS X T iger (10.4.9) AppleTalk-enabled or Bonjour-enabled Printers Bonjour-enabled print er , click the T o add an AppleT alk-enabled or button in the Printer Browser menu. elect the printer model from Printer Name list and Connection type in the Printer rowser menu. The printer name sel ected should be the same a s that [...]

Setting up Printing in Mac OS X T iger (10.4.9) s The printer that has just been added will show up in the Printer List menu, it might take a few se conds depen ding on network conditions. Whe n the printer appears it i ready for use. Quit the Printer Setup Utility and start printing. D-Link DPR-2000 - User Manual 132[...]

Setting up Printing in Mac OS X T iger (10.4.9) Adding an IP Printer T o add an Internet Printing Protocol, Line Printer Daemon, or HP Jet Direct – Socket enabled printer , click the button in the Printer Browser screen. Select a desired printing protocol from the Protocol drop-down menu. T ype the IP Address of the printe r . The name will appea[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 134 correct printer driver in the Print Usi printer-maker from the Print Using d ng field. Y ou can manually select the rop-down menu, and then select the printe r the Print Using drop -down menu if the model is not listed. T o implement the setting, click the Add button.[...]

Setting up Printing in Mac OS X T iger (10.4.9) T o set up LPD Printing: 1. Enter the IP address of the print server to which the pri nter is attach ed in the Address field. 2. T ype the port name in the Queue field. Click the Add button af ter completing the selection of printer model in the Print Using drop-down menu. T o set up IPP Printing: 1. [...]

Setting up Printing in Mac OS X T iger (10.4.9) Click the Add button af ter selecting the printer model i n the Print Using drop-dow n menu. f the print server to which the printer is att ached in the Address field. After that, type “: 9100” for the USB port. blank. T o set up Socket Printing: 1. Enter the IP address o 2. Keep the Queue field D[...]

Setting up Printing in Mac OS X T iger (10.4.9) Click the Add button af ter completing the selection of the printer mo del in the Print Using drop-down menu. e Installable Opti ons pop-up window a ppears, click the Continue but ton. When th D-Link DPR-2000 - User Manual 137[...]

Setting up Printing in Mac OS X T iger (10.4.9) D-Link DPR-2000 - User Manual 138 The printer that has just been added will show up in the Printer List menu, it might take a few se conds depen ding on network conditions. Whe n the printer appears it is ready for use. Quit the Printer Setup Utility and start printing.[...]

Wireless Ba sics D-Link DPR-2000 User Manual 139 Setting up AppleTalk Printing in Mac OS 9 NOTE : Mac OS printing is supported by Post script printers only! The AppleT alk network protocol is used with computers using the MacOS operating system. It can be used for network com munica tions over st andard Ethernet or Fast Ethernet using the EtherT al[...]

Wireless Ba sics same zone as most of the users who wil l be using it. If your network is not divided into zones, the AppleT alk Zone field should cont ain a single asterisk (*). For each Printer Port that will be used for AppleT alk printing, you may need to change the AppleT alk Port Settings in the Advanced LAN screen, shown as bel ow . ppleT al[...]

Wireless Ba sics T m The rocedure described belo w assumes you are using Lase rWriter 8. the LaserWriter 8 ico n on the left. Make sure that AppleT alk is set to Active . A list of all networked PostScript pr inters will be displayed as follows. Double-click the name of the Printer Port y ou wish to use. The Printer Port s shown are examples only .[...]

Wireless Ba sics Select the appropriate printer description file for your printe r . Click Open. (If your printer i s not listed, click Ge neric to use a generic printer description.) If you wish to access this setting in the future, you can use the Setup button in the Chooser window . The selected printer will become your comp uter‘s default pri[...]

Wireless Ba sics D-Link DPR-2000 - User Manual 143 Wireless Basics D-Link wireless p roducts are ba sed on industry st andards to provid e easy-to-use and compatible high-sp eed wireless connectivity within your hom e, business or public access wireless networks. D-Lin k wi reless product s allow you to access the data you want, when and whe re you[...]

Wireless Ba sics D-Link DPR-2000 - User Manual 144 Installing a WLAN sy stem can be cable through walls a nd ceilings. fast and easy and can eliminate the need to pull Wirele ss technology allows the network to go le for a small number of users to large r infrastructure ink devices. ---------- -------- -------- ---------- -------- -------- --------[...]

Setting up AppleT alk Printing in Mac OS 9 D-Link DPR-2000 User Manual 145 Wireless Installation Considerations The D-Link DPR-2000 let s you print through your network, using a wirele ss virtually anywhere within its ope rating range. Keep in mind, ry asic rk um. Each wall or ceiling can redu ce your D-Link wireless p roduct s osi tion your device[...]

Setting up AppleT alk Printing in Mac OS 9 D-Link DPR-2000 - User Manual 146 appliances that generate extreme RF n oise.[...]

Setting up AppleT alk Printing in Mac OS 9 D-Link DPR-2000 - User Manual 147 WPS (Wi-Fi Protected Setup) Wi-Fi Protected Setup (WPS) is a standard for ea sy and secure establishm ent of a wireless network. T raditio nally , users would have to manually create a wireless network name ( SSID ), and then manually entering a creative, yet predict able [...]

T echnical S pecifications D-Link DPR-2000 User Manual 148 Technical Specifications Printer Connection Printer Ports: USB 2.0 (4 ports) Bi-directional Communication: Hewlet t-Packard PJL (Printer Job Langu age standard for bi-directional communication. Ethernet Networ N ) k Connection etwork Standards : IEEE 802.3 u 100BASE-TX Fast Ethernet thernet[...]

Setting up AppleT alk Printing in Mac OS 9 D-Link DPR-2000 - User Manual 149 Emission Certification: FCC Class B, CE Cla ss B, VCCI Class B, C-Tick[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 User Manual 150 Appendix: DPR-2000 Printer Compatibility List Printers Supported on Windo ws 2000 SP4 and Windows XP Printer List Result s (*Y=Pass, N=Fail, N/A=Non-available function) Printer Manufacturer Model Printing Scan Fax 1. Avision MF3100L Y Y N/A 2. Benq CM3000 Y Y N/A 3. Brot[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 - User Manual 151 22. Dell Photo 926 Y Y N/A 23. Dell Photo 966 Y Y Y 24. EPSON PM-A970 Y Y N/A 25. EPSON PM-A920 Y N/A Y 26. EPSON PM-A820 Y Y N/A 27. EPSON PM-A720 Y Y N/A 28. EPSON PM-A950 Y Y N/A 29. EPSON PM-A890 Y Y N/A 30. EPSON PM-A750 Y Y N/A 31. EPSON PM-A650 Y Y N/A 32. 900 E[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 - User Manual 152 48. HP PSC1315 Y Y N/A 49. HP Photosmart C1350 Y Y N/A 50. HP Photosmart C1610 Y Y N/A 51. HP Photosmart C3180 Y Y N/A 52. HP Photosmart C4180 Y Y N/A 53. HP Photosmart C5180 Y Y N/A 54. HP OfficeJet 4255 Y Y Y 55. HP OfficeJet 4355 Y Y Y 56. HP OfficeJet 5510 Y Y Y 57[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 - User Manual 153 Printers Supported ws Vist a 32 on Windo -bit Printer List Result s (*Y=Pass, N=Fail A=Non-avai unction) , N/ lable f Printer Manufacturer Model Printing Scan Fax 1. Avision Y N MF3100L Y /A 2. Benq iver not available N CM3000 Dr /A 3. Brother Y Y MFC-210C Y 4. Brother[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 - User Manual 154 24. EPSON PM-A970 Y Y N/A 25. EPSON PM-A920 Y N/A Y 26. EPSON PM-A820 Y Y N/A 27. 0 EPSON PM-A72 Y Y N/A 28. EPSON PM-A950 Y Y N/A 29. N EPSO PM-A890 Y Y N/A 30. EPSON PM-A750 Y Y N/A 31. EPSON PM-A650 Y Y N/A 32. 0 EPSON S tylus CX290 Y Y N/A 33. 00 EPSON S tylus CX37[...]

Appendix: DPR-2000 Printer Comp atibility List D-Link DPR-2000 - User Manual 155 50. HP Photosmart C1610 Y Y N/A 51. HP Photosmart C3180 Y Y N/A 52. HP Photosmart C4180 Y Y N/A 53. HP Photosmart C5180 Y Y N/A 54. HP LaserJet 3050 r not ble Y Y Drive availa 55. Lexmark x3470 Y Y N/A 56. Lexmark x5470 Y Y Y 57. Samsung SCX-4100 Y Y N/A 58. Samsung SC[...]