Dacor ER48D-C manual

I n s t a l l a t i o n I n s t r u c t i o n s E p i c u r e ® R a n g e For Use with Models: ER36D, ER36D-C, ER48D, ER48D-C Part No. 100843 Rev . R THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LA TEST EDITION OF ANSI Z21.1 ST ANDARD FOR HOUSEHOLD GAS APPLIANCES.[...]

Important Safety Instructions .................................................. 1-3 Customer Service Information .................................................... 3 Planning the Installation ...........................................................4-6 Electrical Requirements .............................................................. 4 Gas[...]

1 Impor tant Infor mation About Safety Instructions The Important Safety Instructions and warnings in this manual are not meant to cover all possible conditions and situations that can occur . Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact the Dacor Customer Service T eam about pro[...]

2 Impor tant Safety Instructions W ARNING Read the accompanying use and care manual before operating this appliance. Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. If you receive a damaged product, immediately contact your dealer or builder . Do not install or use a damaged appliance. This range must be [...]

3 Model Identification ER36D-C-SCH/NG/H SIZE (in inches) COUNTR Y CODE C = Equipped for use in Canada No Character = Equipped for use in U.S.A. GAS TYPE NG = Natural Gas LP = Liquid Petroleum (Propane) AL TITUDE H = Equipped for High Altitude, 4000 feet (1219 m) and up No Character = Equipped for low altitude operation Model and serial number label[...]

4 W ARNING IMPORT ANT : Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information. Electrical Requirements - U.S.A. IMPORT ANT : The information below does not apply to units equipped for use in Canada. It is the owner ’s responsibility to ensure that the electrical[...]

5 48” (1219mm) ** ** ** ** Optional 1 1/16” (27mm) to cooking surface (top of grates) from top of trim Finished Side Panel B A C D Gas Regulator Access, Cover Removed Range Electrical Access, Cover Removed E Electrical Connection Hole in Bottom Inlet Back of Range Planning the Installation Product Dimensions GAS - ELECTRICAL ACCESS DIMENSIONS M[...]

6 3 2, 5 F G 3 Cabinet/countertop depth is at discretion of customer but cabinet face MUST NOT protrude further than rear of front panel, see product dimensions. 4 Consult local code for exact location requirements. 5 Not applicable for cabinets more than a horizontal distance of 10” (254mm) from the edge of the range. 1 V ertical to combustibles[...]

7 Preparing for Installation W ARNING If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer , the gas supplier or a licensed electrician. Before installing the range, you must locate and secure the anti-tip bracket to the floor . • • IMPORT ANT : Within the Common[...]

8 Installation Instructions Installing an ERV Raised V ent (Optional) Install the ERV raised vent before installing the range. See the ERV installation instructions, part no. 103106. IMPORT ANT : The ERV series raised vent attaches to the narrow back portion of the ERV style cutout. It is self-supporting in the cutout and does not actually attach t[...]

9 Fasten the backguard and the stainless steel trim piece in place with the five (5) existing chrome plated screws. Secure the rear of the backguard to the back of the range with the eight (8) existing hex screws. On the 24 inch backguard: Secure the “C” channels on the 24 inch backguard to the brackets mounted on the range chassis using eight [...]

10 Electrical Connection W ARNING Wire the range only in compliance with local ordinances. Improper connection of the electrical wiring can cause an electric shock hazard and damage the appliance. Dacor is not responsible for damages resulting from improper installation. Connect the ground terminal (or lead) on the appliance to a grounded, metallic[...]

1 1 Installation Instructions Loop and Spade T erminal Connections Bare Wire Connections Connecting 4 Wire Conduit to Range Conduit Strain Relief Nut Red Wire White Wire Green Wire Neutral T erminal L1 T erminal L2 T erminal Jumper Removed Black Wire Grounding Screw Connecting 3 Wire Conduit to Range - Where Local Code Permits Conduit Strain Relief[...]

12 Connection to power supply Wire Nut, 3 Places Junction Box Installation Instructions Electrical Connection (continued) Connecting the Conduit to the House Electrical Junction Box W ARNING Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. NOTES: The power supply must be properly polariz[...]

13 Installation Instructions Junction Box - 4 Wire Connection with External Ground Connection to power supply Separate No. 10 (minimum copper grounding wire Junction Box Fasten clamp tightly on pipe Wire Nut, 4 Places Clamps Metal W ater Pipe No. 4 copper wire Meter Bare metal Insulated Pipe Jumper Connect to appliance (page 10)[...]

14 Slide the end of the appliance cord into the strain relief from the bottom of the box Connect the white (neutral) wire to the neutral terminal in the box. Connect the L1 wire to the L1 power supply terminal in the box. Connect the L2 wire to the L2 power supply terminal in the box. If using a 4 Wire connection, connect the ground wire to the gro[...]

15 Gas Supply Connection W ARNING Make sure the gas supply valve is off and that the power to the range is turned off at the circuit breaker or fuse box prior to connecting the gas line. Do not apply excessive pressure when tightening gas connections and fittings. Do not use T eflon tape or plumber ’s putty on gas flex line connections. For LP in[...]

16 Installation Instructions Final Installation Peel the protective coating off of the range, including the door . Adjust the legs to the desired height. Carefully slide the range into position in the cut-out. The rear anti-tip leg should engage the anti-tip bracket. Re-installing the Oven Door(s) W ARNING T o avoid personal injury or damage to the[...]

17 Installing the Burner Components Installation Instructions Stack Burner Installation Burner Head Crown Burner Stack Burner Spill T ray Burner Ring Ridge on bottom of burner cap STEP 1: Put burner ring on top of the head. STEP 2: Turn ring until it drops into place. T wist back and forth to assure proper seating. STEP 3: Install burner caps. Ridg[...]

18 V erifying Proper Operation Prior to operating the cooktop or oven, please read the accompanying use and care manual carefully . Important safety , service and warranty information is contained within the use and care manual. Before beginning the test procedure, ensure that all cooktop control valves are in the “ OFF ” position, and all burn[...]

19 Notes[...]

20 Notes[...]

[...]

Dacor ● 1440 Bridge Gate Drive, Diamond Bar , CA 91765 ● T el: (800) 793-0093 ● F AX: (626) 403-3130 ● www .Dacor .com[...]