Draytek Vigor2110Vn manual

Vigor2110 Series User’s Guide ii Vigor2110 Series Broadband Firewall Router User’s Guide Version: 1.01 Date: 03/07/2009[...]

Vigor2110 Series User’s Guide iii Copyright Information Copyright Declarations Copyright 2009 All rights reserved. This pub lication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stor ed in a retrieval system, or translated into any language withou t written permission from the copyright[...]

Vigor2110 Series User’s Guide iv European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Town ship, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2110 Ser ies Router DrayTek Corp. declares that Vigor2110 Series of ro uters are in compliance with the following essential requirements and other[...]

Vigor2110 Series User’s Guide v T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s 1 Pref ace ............................................................................................................... 1 1.1 Web Conf iguration Bu ttons Explanation ................................................................................. 1 1.2[...]

Vigor2110 Series User’s Guide vi 3.4.2 UPnP..................................................................................................................... .......... 44 3.5 V oIP ....................................................................................................................... ................ 46 3.5.1 Di alPlan .......[...]

Vigor2110 Series User’s Guide vii 4.6.1 IP Object ................................................................................................................ ....... 120 4.5.2 IP Group ................................................................................................................. ...... 122 4.6.3 Service Type Object .......[...]

Vigor2110 Series User’s Guide viii 4.14 System Ma intenance........................................................................................................ . 214 4.12.1 System Status ........................................................................................................... .. 214 4.14.2 TR-069 ............................[...]

Vigor2110 Series User’s Guide 1 1 P P r r e e f f a a c c e e Vigor2110 series is a broadband router. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DS, the router increases the performance of VPN greatl[...]

Vigor2110 Series User’s Guide 2 1 1 . . 2 2 L L E E D D I I n n d d i i c c a a t t o o r r s s a a n n d d C C o o n n n n e e c c t t o o r r s s Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. 1 1 . . 2 2 . . 1 1 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 LED Status Explanation Blinking[...]

Vigor2110 Series User’s Guide 3 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blinking). Press the hole and keep for m ore than 5 seconds . When you see t he ACT LED begins to blink rapidly than usual, release th e butto n. Then the router will restart with the factory default con figura[...]

Vigor2110 Series User’s Guide 4 1 1 . . 2 2 . . 2 2 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Wireless access point is rea dy. WLAN Blinking It will blink while wireless traffic goes through. On The WAN port[...]

Vigor2110 Series User’s Guide 5 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When y ou see the ACT LED be gins to blink rapidly than usual, release the button. Th en th e router will restart with the factory default configuration[...]

Vigor2110 Series User’s Guide 6 1 1 . . 2 2 . . 3 3 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 V V n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Wireless access point is rea dy. WLAN Blinking It will blink while wireless traffic goes through. On The WAN [...]

Vigor2110 Series User’s Guide 7 Interface Description Line Connector for PSTN life line. Phone2/P hone1 Connecter of analog phon e for VoIP com munication . Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When y ou see the ACT LED be gins to blink rapidl[...]

Vigor2110 Series User’s Guide 8 1 1 . . 3 3 H H a a r r d d w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n Before starting to configure the router, you have to connect your devices correctly. 1. Connect Line port to land line jack with a RJ-11 cable (Vn model). 2. Connect this device to a modem with a RJ-45 cable. 3. Connect one [...]

Vigor2110 Series User’s Guide 9 S S t t a a n n d d I I n n s s t t a a l l l l a a t t i i o o n n The Vigor2110 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. c d e f[...]

Vigor2110 Series User’s Guide 10 1 1 . . 4 4 P P r r i i n n t t e e r r I I n n s s t t a a l l l l a a t t i i o o n n You can install a printer onto the router for shar ing printing. All the PCs connected this router can print documents via the router. The exam ple provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please[...]

Vigor2110 Series User’s Guide 11 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port . Click Next .[...]

Vigor2110 Series User’s Guide 12 6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next . 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish .[...]

Vigor2110 Series User’s Guide 13 9. Now, your system will ask you to choose right na me of the printer t hat you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next . 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new [...]

Vigor2110 Series User’s Guide 14 The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional fun ctions are not supported. If you do not know whether your pr inter is supported or not, please vi sit www.draytek.com to [...]

Vigor2110 Series User’s Guide 15 2 C C o o n n f f i i g g u u r r i i n n g g B B a a s s i i c c S S e e t t t t i i n n g g s s For using the router properly, it is necessar y for you to change the password of web configuration for security and adjust primary basic settings. 2 2 . . 1 1 T T w w o o - - L L e e v v e e l l M M a a n n a a g g e[...]

Vigor2110 Series User’s Guide 16 2 2 . . 3 3 C C h h a a n n g g i i n n g g P P a a s s s s w w o o r r d d No matter user mode operation or admin mode operation, please change the password for the original security of the router. 1. Open a web browser on your PC and type http://192. 168.1.1. A pop-up window will open to ask for username and pas[...]

Vigor2110 Series User’s Guide 17 Main screen for user mode operation (simple configuration) Note: The home page will change slightly in acco rdance with the type of the router you have. 4. Go to System Maintenance page and choose Administrator Password/User Password . or 5. Enter the login password (the defa ult is blank) on the field of Old Pass[...]

Vigor2110 Series User’s Guide 18 2 2 . . 4 4 Q Q u u i i c c k k S S t t a a r r t t W W i i z z a a r r d d Notice: Quick Start Wizard for user mode operation is the same as for admin mode operation. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickl y. [...]

Vigor2110 Series User’s Guide 19 2 2 . . 4 4 . . 2 2 P P P P P P o o E E PPPoE stands for Point-to-Point Protocol over Ethernet . It relies on two widely accepted standards: PPP and Ethernet. It connects users th rough an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable m odem. All the u[...]

Vigor2110 Series User’s Guide 20 Click Next for viewing summary of such connection. Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 3 3 P P P P T T P P Click PPTP as the protocol. Type in all the information that your ISP provides for this protocol. Click Next for viewing summary of such connection.[...]

Vigor2110 Series User’s Guide 21 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 4 4 S S t t a a t t i i c c I I P P Click Static IP as the protocol. Type in all the inform ation that your ISP provides for this protocol. After finishing the settings in this page, click Next to see the following page.[...]

Vigor2110 Series User’s Guide 22 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 5 5 D D H H C C P P Click DHCP as the protocol. Type in all the information that your ISP provides for this protocol. After finishing the settings in this page, click Next to see the following page.[...]

Vigor2110 Series User’s Guide 23 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 5 5 O O n n l l i i n n e e S S t t a a t t u u s s The online status shows the system status, WAN st atus, and other status related to this router within one page. If you select PPPoE/PPPoA as the protocol, you will find out a link of D[...]

Vigor2110 Series User’s Guide 24 Name Displays the name set in WAN1/WAN web page. Mode Displays the type of WAN connection (e.g., PPPoE). Up Time Displays the total uptime of the interface. IP Displays the IP address of the WAN interface. GW IP Displays the IP address of the default gateway. TX Packets Displays the total transmitted packets at th[...]

Vigor2110 Series User’s Guide 25 3 U U s s e e r r M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute simple configuration t hrough u ser mode operation. As for other examples of application, please refer to chapter 5. 1. Open a web browser on your PC and type http://192. 168.1.1. The window will ask for [...]

Vigor2110 Series User’s Guide 26 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further [...]

Vigor2110 Series User’s Guide 27 Enable/Disable Click Enable for activating this function. If you click Disable , thi s function will be closed and all the settings that you adjusted in this page will be invalid. ISP Access Setup Enter your allocated username , password and authentication parameters according to the inform ation provided by your [...]

Vigor2110 Series User’s Guide 28 You can set up to 8 public IP addresses other than the current one you are using. Notice that this setting is available for WAN1 only. Fixed IP – Click Yes to use this function and type in a fixed IP address in the box of Fixed IP Address . Default MAC Address – You can use Default MAC Address or specify anoth[...]

Vigor2110 Series User’s Guide 29 Access Control Click Enable for activating this function. If you click Disable , this function will be closed and all the settings that you adjusted in this page will be invalid. Keep WAN Connection Normally, this function is designed for Dynamic IP environm ents because some ISPs will drop connections if there is[...]

Vigor2110 Series User’s Guide 30 WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN in terface, please use WAN IP Alias. You can set up to 8 public IP addresses other than the current one you are using. Obtain an IP address automatically – Click this button to obtain the IP address automatically if[...]

Vigor2110 Series User’s Guide 31 PPTP Setup Enable - Click this radio button to enable a PPTP client to establish a tunnel to a DSL modem on the WAN interface. Disable – Click this radio button to close the connection thr ough PPTP. PPTP Server - Specify the IP address of the PPTP/L2TP server if you enable PPTP/L2TP client mode. ISP Access Setu[...]

Vigor2110 Series User’s Guide 32 3 3 . . 2 2 L L A A N N Local Area Network (LAN) is a group of subnets regulated and ruled by router . The design of network structure is related to what type of public IP addresses coming from your ISP . 3 3 . . 2 2 . . 1 1 B B a a s s i i c c s s o o f f L L A A N N The most generic function of V igor router is [...]

Vigor2110 Series User’s Guide 33 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing. This allows users to cha nge the information of the r[...]

Vigor2110 Series User’s Guide 34 2 nd IP Address T y pe in secondary IP address for connecting to a subnet. (Default: 192.168.2.1/ 24) 2 nd Subnet Mask An address code that determines the size of the network. (Default: 255.255.255.0/ 24) 2 nd DHCP Se rver Y ou can configure the router to serve as a DHCP server for the 2nd subnet. S tart IP Addres[...]

Vigor2110 Series User’s Guide 35 DHCP Server Configuration DHCP stands for Dynamic Host Configuration Protoc ol. The router by factory default acts a DHCP server for your network so it automatically dispatch related IP settings to any local user configured as a DHCP client. It is highly recommended that you leave the router enabled as a DHCP serv[...]

Vigor2110 Series User’s Guide 36 If both the Primary IP and Secondary IP Address fields are left empty , the router will assign its own IP address to local users as a DNS proxy server and maintain a DNS cache. If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately . Otherwise, the route[...]

Vigor2110 Series User’s Guide 37 The port redirection can only apply to incoming traffic. To use this function, please go to NAT page and choose Port Redirection web page. The Port Redirection Table provides 20 port-m apping entries for the internal hosts. Press any number under Index to access into next page for configuring port redirection.[...]

Vigor2110 Series User’s Guide 38 Enable Check this box to enable su ch port redirection setting. Mode Two options (Single and Range) are provided here for you to cho ose. To set a range for the specific service, select Range . In Range mode, if the public port (start port and end port) and the starting IP of private IP had been entered, the syste[...]

Vigor2110 Series User’s Guide 39 single host in the LAN. Regular web surfing and other such Internet activities from other clients will continue to work w ithout inappropriate interruption. DMZ Ho st allows a defined internal user to be totally exposed to th e Internet, which usually helps some special applications such as Netmeeting or Internet [...]

Vigor2110 Series User’s Guide 40 Enable Check to enable the DMZ Host function. Private IP Enter the private IP address of the DMZ host, or click Choose PC to select one. Choose PC Click this button and then a window will automatically pop up, as depicted below. The window consists of a list of private IP addresses of all hosts in your LAN network[...]

Vigor2110 Series User’s Guide 41 3 3 . . 3 3 . . 3 3 O O p p e e n n P P o o r r t t s s Open Ports allows you to open a range of ports for the traffic of special applications. Common application of Open Ports includes P2 P application (e.g., BT, KaZaA, Gnutella, WinMX, eMule and others), Internet Camera etc. Ensure that you keep the application [...]

Vigor2110 Series User’s Guide 42 Enable Open Ports Check to enable this entry. Comment Make a name for the defined network application/service. WAN IP Specify the WAN IP address that w ill be used for this entry. This setting is available when WAN IP Alias is configured. Local Computer Enter the private IP address of the local host or click Choos[...]

Vigor2110 Series User’s Guide 43 registered domain name to access the router or internal virtual servers from the Internet. It is particularly helpful if you host a web server, FTP server, or other server behind t he router. Before you use the Dynamic DNS feature, you have to apply for free DDNS service to the DDNS service providers. The router p[...]

Vigor2110 Series User’s Guide 44 Enable Dynamic DNS Account Check this box to enable the current account. If you did check the box, you will see a ch eck mark appeared on the Active column of the previous web page in step 2). Service Provider Select the service provider for the DDNS account. Service Type Select a service type (Dynamic, Custom or [...]

Vigor2110 Series User’s Guide 45 Enable UPNP Service Accordingly , you can enable either the Connection Contr ol Service or Connection S tatus Service . After setting Enable UPNP Service setting, an icon of IP Br oadband Connection on Router on W indows XP/Network Connections will appear . The connection status and control status will be able to [...]

Vigor2110 Series User’s Guide 46 The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your P C may cause the UPnP function not working properly. This is because these applicati ons will block the accessing ability of some network ports. Security Considerations Activating [...]

Vigor2110 Series User’s Guide 47 while the MGCP protocol uses client-server architecture, the calling scenario being very similar to the current PSTN/ISDN network. After a call is setup, the voice streams transmit via RTP (Real-Time Transport Protocol). Different codecs (methods to compress and en code the voice) can be embedded into RTP packets.[...]

Vigor2110 Series User’s Guide 48 Our Vigor V models firstly apply efficient codecs designed to make the best use of available bandwidth, but Vigor V models also equip with autom atic QoS assurance. QoS Assurance assists to assign high priori ty to voice traffic via Internet. You will always have the required inboun d and outbound bandwidth that i[...]

Vigor2110 Series User’s Guide 49 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Phone Number The speed-dial number of this index. This can be any number you choose, using digits 0- 9 and * . Display Name The Caller-ID that you want to be displayed on your friend’s screen. This let your friend[...]

Vigor2110 Series User’s Guide 50 the same SIP server, sometimes, the VoIP phone call connection may not succeed. By using the specified dial out account, the successful connection can be assured. Loop through The selection should be as the following: Backup Phone Number When the VoIP phone is obstructs or the Internet breaks down for some reasons[...]

Vigor2110 Series User’s Guide 51 Enable Check this box to invoke this setting. Prefix Number The phone number set here is used to add, strip, or replace the OP number. Mode None - No action. Add - When you choose this mode, the OP number will be added with the prefix number for calling out through the specific VoIP interface. Strip - When you cho[...]

Vigor2110 Series User’s Guide 52 will be changed to “886311111 11” and sent to SIP server. OP Number The front number you type here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number. Min Len Set the minimal length of the dial number for appl ying the pre[...]

Vigor2110 Series User’s Guide 53 Enable Click this to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Barring Type Determine the type of the VoIP phone call, URI/URL or number. Specific URI/URL or Specific Number This field wi[...]

Vigor2110 Series User’s Guide 54 For Block Unknown Domain – this function can block incomi ng calls (through Phone port) from unrecognized domain that is not specified in SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) com ing from[...]

Vigor2110 Series User’s Guide 55 Last Call Return [Miss] Sometimes, people might miss some phone calls. Please dial number typed in this field to know where the last phone call comes from and call back to that one. Last Call Return [In] You have finished an incoming phone call, however you want to call back again for some reason. Please dial numb[...]

Vigor2110 Series User’s Guide 56 Call Waiting [Act] Dial the number typed in this field to make all the incoming calls waiting for your answer. Call Waiting [Deact] Dial the number typed in this field to release this function. Block Anonymous[Act] Dial the number typed in t his field to block all the incoming calls with unknown ID. Block Anonymou[...]

Vigor2110 Series User’s Guide 57 As Vigor VoIP Router is turned on, it will first register with Registrar using AuthorizationUser@Domain/Realm. After that, y our call will be bypassed by SIP Proxy to the destination using AccountName@Domain/Realm as identity. Index Click this link to access into next page for setting SIP account. Profile Display [...]

Vigor2110 Series User’s Guide 58 Profile Name Assign a name for this profile for identifying. You can t ype similar name with the domain. For example, if the domain name is draytel.org , then you might set draytel-1 in this field. Register via If you want to make VoIP call without register personal information, please choose None and check the bo[...]

Vigor2110 Series User’s Guide 59 setting value is the same as Account Name, it is not necessary for you to check the box and set any value in this field. Password The password provided to you when you registered with a SIP service. Expiry Time The time duration that your SIP Registrar server keeps your registration record. Before the time expires[...]

Vigor2110 Series User’s Guide 60[...]

Vigor2110 Series User’s Guide 61 Phone List Port – t here are two phone ports provided here for you to configure. Phone1/Phone2 allow you to set general settings for PSTN phones. Call Feature – A brief description for call feature will be shown in this field for your reference. Codec – The default Codec setting for each port will be shown i[...]

Vigor2110 Series User’s Guide 62 Hotline Check the box to enable it. Type in the SIP URL in the field for dialing automatically when you pick up the phone set. Session Timer Check the box to enable the function. In the limited time that you set in this field, if there is no response, the connecting call will be closed automatically. Call Forwardi[...]

Vigor2110 Series User’s Guide 63 profiles. Refer to section VoIP>>DialPlan>>Phone Book for detailed configuration. CLIR (hide caller ID) Check this box to hide the caller ID on the display pa nel of the phone set. Call Waiting Check this box to invoke this function. A notice sound will appear to tell the user new phone call is waiting[...]

Vigor2110 Series User’s Guide 64 In addition, you can press the Advanced button to configure tone settings, volume gain, MISC and DTMF mode. Advanced setting is provided for fitting t he telecommunication custom for the local area of the router installed. Wrong tone settings might cause inconvenience for users. To set the sound pattern of the pho[...]

Vigor2110 Series User’s Guide 65 Also, you can specify each field for your necessity. It is recommended for you to use the default settings for VoIP communication. Volume Gain Mic Gain (1-10)/Speaker Gain (1-10) - Adjust the volume of microphone and speaker by entering number from 1- 10. The larger of the number, the louder the volume is. MISC Di[...]

Vigor2110 Series User’s Guide 66 Refresh Seconds Specify the interval of refresh time to obtain the latest VoIP calling information. The information will update immediately when the Refresh button is clicked. Port It shows current connection status for the port of Phone1 and Phone2. Status It shows the VoIP connection status. IDLE - Indicates tha[...]

Vigor2110 Series User’s Guide 67 In Calls Accumulation for the times of in call. Out Calls Accumulation for the times of out call. Miss Calls Accu mulation for the times of missing call. Speaker Gain The volume of present call. Log Display logs of VoIP calls. 3 3 . . 6 6 W W i i r r e e l l e e s s s s L L A A N N This function is used for “n?[...]

Vigor2110 Series User’s Guide 68 S S e e c c u u r r i i t t y y O O v v e e r r v v i i e e w w Real-time Hardware Encryption: Vigor Router is equipped with a hardware AES encryption engine so it can apply the highest prote ction to your data without influencing user experience. Complete Security Standard Selection: To ensure the security and pr[...]

Vigor2110 Series User’s Guide 69 Enable Wireless LAN Check the box to enable wireless function. Mode At present, the router can connect to Mixed (11b+11g), 11g Only, 11b Only, Mixed (11g+1 1n), 11n Only and Mixed (11b+11g+11n) stations simultaneously. Sim ply choose Mix (11b+11g+11n) m ode. Note: You should also set RADIUS Server simultaneously i[...]

Vigor2110 Series User’s Guide 70 system determine for you. Packet-OVERDRIVE This feature can enhance the performance in data transmission about 40%* m ore (by checking Tx Burs t). It is active only when both sides of Access Point and Station (in wireless client) invoke this function at the same time. That is, the wireless client must support this[...]

Vigor2110 Series User’s Guide 71 preamble with 56 bit sync field instead of long pream ble with 128 bit sync field. However, some original 11b wireless network devices only support long preamble. Check it to use Long Preamble if needed to communicate with this kind of devices. 3 3 . . 6 6 . . 3 3 S S e e c c u u r r i i t t y y By clicking the Se[...]

Vigor2110 Series User’s Guide 72 WPA The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Either 8~63 ASCII characters, such as 012345678(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde[...]

Vigor2110 Series User’s Guide 73 Enable Mac Access Filter Select to enable the MAC Address filter for wireless LAN identified with SSID 1 to 4 respectively. All the clients (expressed by MAC addresses) listed in the box can be grouped under different wireless LAN. For example, they can be grouped under SSID 1 and SSID 2 at the same time if you ch[...]

Vigor2110 Series User’s Guide 74 as guard interval, the AP router will choose short guard interval (increasing the wireless performance) or long guard interval for data transmit based on the station capability. Aggregation MSDU Aggregation MSDU can combine frames with different sizes. It is used for improving MAC layer’s performance for some br[...]

Vigor2110 Series User’s Guide 75 ranging from 1 to 15. Be aware that CWMax value must be greater than CWMin or equals to CWMin value. Both values will influence the time delay for WMM accessing categories. The difference between AC_VI and AC_VO categories must be smaller; however, the difference between AC_BE and AC_BK categories must be greater.[...]

Vigor2110 Series User’s Guide 76 Refresh Click this button to refresh the status of station list. Add Click this button to add current typed MAC address into Access Contro l. 3 3 . . 7 7 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration:[...]

Vigor2110 Series User’s Guide 77 Model Name Display the model name of the router. Firmware Version Display the firmware version of the router. Build Date/Time Display the date and time of the current firmware build. LAN------- MAC Address Display the MAC address of the LAN Interface. 1 st IP Address Display the IP address of the LAN interface. 1 [...]

Vigor2110 Series User’s Guide 78 Old Password Type in the old password. The factory default setting for password is blank. New Password Type in new password in this field. Confirm Password Type in the new password again. When you click OK, the login window will a ppear. Please use the new password to access into the web configurator again. 3 3 . [...]

Vigor2110 Series User’s Guide 79 3 3 . . 7 7 . . 4 4 R R e e b b o o o o t t S S y y s s t t e e m m The Web Configurator may be used to restart your router for using current configuration. Click Reboot System from System Maintenance to open the following page. Click OK . The router will take 5 seconds to reboot the system. Note: When the system [...]

Vigor2110 Series User’s Guide 80 3 3 . . 8 8 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics. 3 3 . . 8 8 . . 1 1 D D H H C C P P T T a a b b l l e e The facility provides information on IP address as signments. This i[...]

Vigor2110 Series User’s Guide 81 3 3 . . 8 8 . . 2 2 P P i i n n g g D D i i a a g g n n o o s s i i s s Click Diagnostics and click Ping Diagnosis to pen the web page. Ping to Use the drop down list to choose the destination that y ou want to ping. IP Address Type in the IP address of the Host/IP that you want to ping. Run Click this button to s[...]

Vigor2110 Series User’s Guide 82[...]

Vigor2110 Series User’s Guide 83 4 A A d d m m i i n n M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute adva nced (full) configuration thr ough admin mode operation. As for other examples of application, please refer to chapter 5. 1. Open a web browser on your PC and type http://192. 168.1.1. The window[...]

Vigor2110 Series User’s Guide 84 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further protect its LAN, it interconnects groups of host PCs. Each of them has a private IP address assigned b[...]

Vigor2110 Series User’s Guide 85 Enable/Disable Click Enable for activating this function. If you click Disable , thi s function will be closed and all the settings that you adjusted in this page will be invalid. ISP Access Setup Enter your allocated username , password and authentication parameters according to the inform ation provided by your [...]

Vigor2110 Series User’s Guide 86 Fixed IP – Click Yes to use this function and type in a fixed IP address in the box of Fixed IP Address . Default MAC Address – You can use Default MAC Address or specify another MAC address by typing on the boxes of MAC Address for the router. Specify a MAC Address – Type the MAC address f or the router man[...]

Vigor2110 Series User’s Guide 87 Access Control Click Enable for activating this function. If you click Disable , this function will be closed and all the settings that you adjusted in this page will be invalid. Keep WAN Connection Normally, this function is designed for Dynamic IP environm ents because some ISPs will drop connections if there is[...]

Vigor2110 Series User’s Guide 88 WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN in terface, please use WAN IP Alias. You can set up to 8 public IP addresses other than the current one you are using. Obtain an IP address automatically – Click this button to obtain the IP address automatically if[...]

Vigor2110 Series User’s Guide 89 PPTP Setup Enable - Click this radio button to enable a PPTP client to establish a tunnel to a DSL modem on the WAN interface. Disable – Click this radio button to close the connection thr ough PPTP. PPTP Server - Specify the IP address of the PPTP/L2TP server if you enable PPTP/L2TP client mode. ISP Access Setu[...]

Vigor2110 Series User’s Guide 90 4 4 . . 2 2 L L A A N N Local Area Network (LAN) is a group of subnets regulated and ruled by router . The design of network structure is related to what type of public IP addresses coming from your ISP . 4 4 . . 2 2 . . 1 1 B B a a s s i i c c s s o o f f L L A A N N The most generic function of V igor router is [...]

Vigor2110 Series User’s Guide 91 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing. This allows users to cha nge the information of the r[...]

Vigor2110 Series User’s Guide 92 4 4 . . 2 2 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup . 1st IP Addr ess T ype in private IP address for connecting to a local private network (Default: 192.168.1.1). 1st Subnet Mask T[...]

Vigor2110 Series User’s Guide 93 S tart IP Address: Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses. If the 2nd IP address of your router is 220.135.240.1, the starti ng IP address must be 220.135.240.2 or greater , but smaller than 220.135.240.254. IP Pool Counts: Enter the number of IP addresses [...]

Vigor2110 Series User’s Guide 94 If you want to use another DHCP server in the network other than the V igor Router ’ s, you can let Relay Agent help you to redirect the DHCP request to the specified location. Enable Server - Let the router assign IP address to every host in the LAN. Disable Server – Let you manually assign IP address to ever[...]

Vigor2110 Series User’s Guide 95 There are two common scenarios of LAN setti ngs that stated in Chapter 4. For the configuration examples, please refer to that chap ter to get more information for your necessity. 4 4 . . 2 2 . . 3 3 S S t t a a t t i i c c R R o o u u t t e e Go to LAN to open setting page and choose Static Route . Index The numb[...]

Vigor2110 Series User’s Guide 96 1. Go to LAN page and click General Setup , select 1st Subnet as the RIP Protocol Control. Then click the OK button. Note: There are two reasons that we have to appl y RIP Protocol Control on 1st Subnet. The f irst is that the LAN inte rface can exchange RI P packets with the neighboring routers via the 1st subnet[...]

Vigor2110 Series User’s Guide 97 4. Go to Diagnostics and choose Routing T able to verify current routing table.[...]

Vigor2110 Series User’s Guide 98 4 4 . . 2 2 . . 4 4 V V L L A A N N Virtual LAN function provides you a very convenient way to manage hosts by g rouping them based on the physical port. You can also mana ge the in/out rate of each port. Go to LAN page and select VLAN . The following page will appear. Click Enable to invoke VL AN function. To add[...]

Vigor2110 Series User’s Guide 99 4 4 . . 2 2 . . 5 5 B B i i n n d d I I P P t t o o M M A A C C This function is used to bind the IP and MAC address in LAN to have a strengthening co ntrol in network. When this function is enabled, all the assigned IP and MAC address binding together cannot be changed. If you modified the binding IP or MAC addre[...]

Vigor2110 Series User’s Guide 100 Add It allows you to add the one you choose from the ARP table or the IP/MAC address typed in Add and Edit to the table of IP Bind List . Edit It allows you to edit and modify the selected IP address and MAC address that you create before. Remove You can remove any item listed in IP Bind List . Simply click and s[...]

Vigor2110 Series User’s Guide 101 forward all access request with public IP address fro m external users to the mapping private IP address/port of the server. The port redirection can only apply to incoming traffic. To use this function, please go to NAT page and choose Port Redirection web page. The Port Redirection Table provides 20 port-m appi[...]

Vigor2110 Series User’s Guide 102 Enable Check this box to enable su ch port redirection setting. Mode Two options (Single and Range) are provided here for you to cho ose. To set a range for the specific service, select Range . In Range mode, if the public port (start port and end port) and the starting IP of private IP had been entered, the syst[...]

Vigor2110 Series User’s Guide 103 4 4 . . 3 3 . . 2 2 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (A H), do not travel on a fixed po[...]

Vigor2110 Series User’s Guide 104 The security properties of NA T are somewhat bypassed if you set up DMZ host. W e suggest you to add additional filter rules or a secondary firewall. Click DMZ Host to open the following page: If you previously have set up WAN Alias for PPPoE or Static or Dynamic IP mode , you will find them in Aux. WAN IP for yo[...]

Vigor2110 Series User’s Guide 105 Choose PC Click this button and then a window will automatically pop up, as depicted below. The window consists of a list of private IP addresses of all hosts in your LAN network. Select one private IP address in the list to be the DMZ host. When you have selected one private IP from the above dialog, the IP addr[...]

Vigor2110 Series User’s Guide 106 Index Indicate the relative number for the particular entry that you want to offer service in a local host. You should click the appropriate index number to edit or clear the corresponding entry. Comment Specify the name for the defined network service. Local IP Address Display the private IP address of the local[...]

Vigor2110 Series User’s Guide 107 4 4 . . 4 4 H H a a r r d d w w a a r r e e A A c c c c e e l l e e r r a a t t i i o o n n Hardware-base Accelerati on Engine, also na med Protocol Processing Engine API is the function that Draytek provides to extr emely speed up the NAT performance. While the hardware acceleration mechanism is activated, m ost[...]

Vigor2110 Series User’s Guide 108 4 4 . . 5 5 F F i i r r e e w w a a l l l l 4 4 . . 5 5 . . 1 1 B B a a s s i i c c s s f f o o r r F F i i r r e e w w a a l l l l While the broadband users demand more bandwidth f or multimedia, interactive applications, or distance learning, security has been always the most concerned. The firewall of the Vigo[...]

Vigor2110 Series User’s Guide 109 S S t t a a t t e e f f u u l l P P a a c c k k e e t t I I n n s s p p e e c c t t i i o o n n ( ( S S P P I I ) ) Stateful inspection is a firewall architecture that works at the network layer. Unlike legacy static packet filtering, which examines a packet based on the information in its header, stateful inspec[...]

Vigor2110 Series User’s Guide 110 4 4 . . 5 5 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p General Setup allows you to adjust setti ngs of IP Filter and common options. Here you can enable or disable the Call Filter or Data Filter . Under some circumstance, your filter set can be linked to work in a serial manner. So here you assign th[...]

Vigor2110 Series User’s Guide 111 will be sent to Syslog server . Please refer to section 4.14.4 Syslog/Mail Alert for more detailed information. W eb Content Filter Select one of the W eb Content Filter profile settings (created in CSM>> W eb Content Filter ) for applying with this router . Please set at least one profile for anti-virus in[...]

Vigor2110 Series User’s Guide 112 Window size – It determines the size of TCP protocol (0~65535). The m ore the value is, the better the performance will be. However , if the network is not stable, sm all value will be proper . Session timeout –Setting timeout for sessions can make the best utilization of network resources. However , Queue ti[...]

Vigor2110 Series User’s Guide 113 Active Enable or disable the filter rule. Comment Enter filter set comments/description. Maximum length is 23–character long. Move Up/Down Use Up or Down link to m ove the order of the filter rules. Next Filter Set Set the link t o the next filter set to be executed after the current filter run. Do not make a l[...]

Vigor2110 Series User’s Guide 114 as the Address Type. From the IP Group drop down list, choose the one that you want to apply. Or use the IP Object drop down list to choose the object that you want. Service Type Click Edit to access into the following dialog to choose a suitable service type. To set the service type manually, please choose User [...]

Vigor2110 Series User’s Guide 115 Fragments Specify the action for fragmented packets. And it is used for Data Filter only. Don’t care - No action will be taken towards fragmented packets. Unfragmented - Apply the rule to unfragmented packets. Fragmented - Apply the rule to fragmented packets. Too Short - Apply the rule only to packets that are[...]

Vigor2110 Series User’s Guide 116 E E x x a a m m p p l l e e As stated before, all the traffic will be separate d and arbitrated using on of two IP filters: call filter or data filter. You may preset 12 call filters and data filters in Filter Setup and even link them in a serial manner. Each filter set is co mposed by 7 filter rules, which can b[...]

Vigor2110 Series User’s Guide 117 4 4 . . 5 5 . . 4 4 D D o o S S D D e e f f e e n n s s e e As a sub-functionality of IP Filter/Firewall, th ere are 15 types of detect/ defense function in the DoS Defense setup. The DoS Defense functionality is disabled for default. Click Firewall and click DoS Defense to open the setup page. Enable Dos Defense[...]

Vigor2110 Series User’s Guide 118 Enable PortScan detection Port Scan attacks the Vigor router by sending lots of packets to many ports in an attempt to find ignorant services would respond. Check the box to activate the Port Scan detection. Whenever detecting this malicious exploration behavior by monitoring the port-scanning Threshold rate, the[...]

Vigor2110 Series User’s Guide 119 Block Unknown Protocol Check the box to activate the Block Unknown Protocol function. Individual IP packet has a protocol field in the datagram header to indicate the protocol type running over the upper layer. However, the protocol types greater than 100 are reserved and undefined at this time. Therefore, the ro[...]

Vigor2110 Series User’s Guide 120 4 4 . . 6 6 O O b b j j e e c c t t s s S S e e t t t t i i n n g g s s For IPs in a range and service ports in a limited range usually will be applied in configuri ng router’s settings, therefore we can define them with objects and bind them with groups for using conveniently. Later, we can select that object/[...]

Vigor2110 Series User’s Guide 121 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose a proper interface (WAN, LAN or Any). For example, the Direction setting in Edit Filter Rule will ask you specify IP or IP range for WAN or LAN or any IP address. If you choose LAN as the Interface here, and choose LAN as the d[...]

Vigor2110 Series User’s Guide 122 4 4 . . 5 5 . . 2 2 I I P P G G r r o o u u p p This page allows you to bind several IP objects into one IP group. Set to Factory Default Clear all profiles. Click the number under Index colu mn for settings in detail.[...]

Vigor2110 Series User’s Guide 123 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose WAN, LAN or Any to display all the available IP objects with the specified interface. Available IP Objects All the available IP objects with the specified interface chosen above will be shown in this box. Selected IP Objects Cl[...]

Vigor2110 Series User’s Guide 124 4 4 . . 6 6 . . 3 3 S S e e r r v v i i c c e e T T y y p p e e O O b b j j e e c c t t You can set up to 96 sets of Service Type Objects with different conditions. Set to Factory Default Clear all profiles. Click the number under Index co lumn for settings in detail. Name Type a name for this profile. Protocol S[...]

Vigor2110 Series User’s Guide 125 (=) – when the first and last value are the same, it indicates one port; when the first and last values are different, it indicates a range for the port and available for this profile. (!=) – when the first and last value are the same, it indicates all the ports except the port defi ned here; when the first a[...]

Vigor2110 Series User’s Guide 126 Name Type a name for this profile. Available Service Type Objects All the available service objects that you have added on Objects Setting>>Service Type Object will be shown in this box. Selected Service Type Objects Click >> button to add the selected IP objects in this box. 4 4 . . 6 6 . . 5 5 K K e[...]

Vigor2110 Series User’s Guide 127 Name Type a name for this profile, e.g., game. Contents Type the content for such profile. For example, type gambling as Contents. When you browse th e webp age, the page with gambling information will be watched out and be passed/blocked based on the conf iguration on Firewall settings. 4 4 . . 5 5 . . 6 6 K K e[...]

Vigor2110 Series User’s Guide 128 Name Type a name for this group. Available Keyword Objects You can gather keyword objects from Keyword Object page within one keyword group. All the available Keyword objects that you have created will be shown in this box. Selected Keyword Objects Click button to add the selected Keyword objects in this box. 4 4[...]

Vigor2110 Series User’s Guide 129 Profile Name Type a name for this profile. Type a name for such profile and check all the ite ms of file extension that will be processed in the router. Finally, click OK to save this profile.[...]

Vigor2110 Series User’s Guide 130 4 4 . . 6 6 . . 8 8 I I M M O O b b j j e e c c t t This page allows you to set 32 profiles for In stant Messenger. These profiles will be applied in CSM>>IM/P2P Filter Profile for filtering. Set to Factory Default Clear all profiles. Click the number under Profile column for config uration in details. Ther[...]

Vigor2110 Series User’s Guide 131 4 4 . . 6 6 . . 9 9 P P 2 2 P P O O b b j j e e c c t t This page allows you to set 32 profiles for p eer-to-peer application. These profiles will be applied in CSM>>IM/P2P Filter Profile for filtering. Set to Factory Default Clear all profiles. Click the number under Profile column for config uration in de[...]

Vigor2110 Series User’s Guide 132 4 4 . . 6 6 . . 1 1 0 0 M M i i s s c c O O b b j j e e c c t t This page allows you to set 32 profiles for mi scellaneous applications. These profiles will be applied in CSM>>IM/P2P Filter Profile for filtering. Set to Factory Default Clear all profiles. Click the number under Profile column for configurat[...]

Vigor2110 Series User’s Guide 133 4 4 . . 7 7 C C S S M M P P r r o o f f i i l l e e C C o o n n t t e e n n t t S S e e c c u u r r i i t t y y M M a a n n a a g g e e m m e e n n t t ( ( C C S S M M ) ) CSM is an abbreviation of Content Security Management which is used to control IM/P2P usage, filter the web content and URL conten t to reach [...]

Vigor2110 Series User’s Guide 134 Vigor router will then decide whether to allow access to this site according to the categories you have selected. Please note that this action will not introduce any delay in your Web surfing because each of multiple load balanced datab ase servers can handle millions of requests for categorization. Note: The pri[...]

Vigor2110 Series User’s Guide 135 Each profile can contain three objects settings, IM Object, P2P Object and Misc Object. Such profile can be applied in the Firewall>>General Setup and Firewall>>Filter Setup pages as the standard for the host(s) to follow. 4 4 . . 7 7 . . 2 2 U U R R L L C C o o n n t t e e n n t t F F i i l l t t e e[...]

Vigor2110 Series User’s Guide 136 Profile Name Type the name for such profile. Priority It determines the action that this router will apply. Both: Pass – The router will let all the packages that match with the conditions specified in URL Access Control and Web Feature below passing through. When you choose this setting, both configuration set[...]

Vigor2110 Series User’s Guide 137 All – All the actions (Pass and Block) will be recorded in Syslog. URL Access Control Enable URL Access Control - Check the box to activate URL Access Control. Note that the priority for URL A ccess Control is higher than Restrict Web Feature . If the web content match the setting set in URL Access Control, the[...]

Vigor2110 Series User’s Guide 138 Web Feature Enable Restrict Web Feature - Check this box to make the keyword being blocked or passed. Action - This setting is available only when Either: URL Access Control First or Either : Web Feature Firs is selected. Pass allows accessing into the corresponding webpage with the ke ywords listed on the box be[...]

Vigor2110 Series User’s Guide 139 4 4 . . 7 7 . . 3 3 W W e e b b C C o o n n t t e e n n t t F F i i l l t t e e r r P P r r o o f f i i l l e e We all know that the content on the Internet just like other types of media may be inappropriate sometimes. As a r esponsible parent or employer, you should protect those in your trust against the hazar[...]

Vigor2110 Series User’s Guide 140 Action Pass - allow accessing into the corr esponding webpage with the categories listed on the box below. Block - restrict accessing into the corresponding webpage with the categories listed on the box below. If the web pages do not match with the specified feature set here, it will be processed with reverse act[...]

Vigor2110 Series User’s Guide 141 4 4 . . 8 8 B B a a n n d d w w i i d d t t h h M M a a n n a a g g e e m m e e n n t t Below shows the menu items for Bandwidth Management. 4 4 . . 8 8 . . 1 1 S S e e s s s s i i o o n n s s L L i i m m i i t t A PC with private IP address can access to the Internet via NAT router. The router will generate the [...]

Vigor2110 Series User’s Guide 142 Maximum Sessions Defines the av ailable session number for each host in the specific range of IP addresses. If you do not set the session number in this field, the system will use the default session limit for the specific limitation you set for each index. Add Adds the specific session limitation onto the list a[...]

Vigor2110 Series User’s Guide 143 Default TX limit Define the default speed of the upstream for each computer in LAN. Default RX limit Define the default speed of the downstream for each com puter in LAN. Limitation List Display a list of specific limitations that you set on this web page. Start IP Define the start IP address for limit bandwidth.[...]

Vigor2110 Series User’s Guide 144 One more larger-scale imple mentation of QoS network is to apply DSCP (Differentiated Service Code Point) and IP Precedence disciplines at Layer 3. Compared with legacy IP Precedence that uses Type of Service (ToS) field in the IP header to define 8 service classes, DSCP is a successor creating 64 classes possibl[...]

Vigor2110 Series User’s Guide 145 G G e e n n e e r r a a l l S S e e t t u u p p f f o o r r W W A A N N I I n n t t e e r r f f a a c c e e When you click Setup , you can configure the bandwidth ratio for QoS of the WAN interface. There are four queues allowed for QoS control. The first three (Class 1 to Class 3) class rules can be adjusted for[...]

Vigor2110 Series User’s Guide 146 lots of bandwidth. Outbound TCP ACK Prioritize The difference in bandwidth between download and upload are great in ADSL2+ environment. For the download speed might be impacted by the uploading TCP ACK, you can check this box to push ACK of upload faster to speed the network traffic. Limited_bandwidth Ratio The r[...]

Vigor2110 Series User’s Guide 147 For adding a new rule, click Add to open the following page. ACT Check this box to invoke these settings. Local Address Click the Edit button to set the local IP address (on LAN) for the rule. Remote Address Click the Edit button to set the remote IP address (on LAN/WAN) for the rule. Edit It allows you to edit s[...]

Vigor2110 Series User’s Guide 148 Please assign one of the levels of the data for processing with QoS control. Service Type It determines the service type of the data for processing with QoS control. It can also be edited. You can choose the predefined service type from the Service Type drop down list. Those types are predefined in factory. Simpl[...]

Vigor2110 Series User’s Guide 149 For adding a new service type, click Add to open the following pag e. Service Name Type in a new service for your request. Service Type Choose the type (TCP, UDP or TCP/UDP) for the new service. Port Configuration Click Single or Range as the Type . If you select Range, you have to type in the starting port numbe[...]

Vigor2110 Series User’s Guide 150 4 4 . . 9 9 A A p p p p l l i i c c a a t t i i o o n n s s Below shows the menu items for Applications. 4 4 . . 9 9 . . 1 1 D D y y n n a a m m i i c c D D N N S S The ISP often provides you with a dynamic IP address when you c onnect to the Internet via your ISP. It means that the public IP address assigned to [...]

Vigor2110 Series User’s Guide 151 Index Click the number below Index to access into the setting page of DDNS setup to set account(s). Domain Name Display the domain name that you set on the setting page of DDNS setup. Active Display if this account is active or inactive. View Log Display DDNS log status. Force Update Force the router updates its [...]

Vigor2110 Series User’s Guide 152 In the DDNS setup menu, click the Index number you want to delete and then push Clear All button to delete the account. 4 4 . . 9 9 . . 2 2 S S c c h h e e d d u u l l e e The Vigor router has a built-in real time clock which can update itself manually or automatically by means of Network Time Protocols (NTP). As[...]

Vigor2110 Series User’s Guide 153 Enable Schedule Setup Check to enable the schedule. Start Date (yyyy-mm-dd) Specify the starting date of the schedule. Start Time (hh:mm) Specify the starting time of the schedule. Duration Time (hh:mm) Specify the duration (or period) for the schedule. Action Specify which action Call Schedule should apply durin[...]

Vigor2110 Series User’s Guide 154 2. Configure the PPPoE always on from 9:00 to 18:00 f or whole week. 3. Configure the For ce Down from 18:00 to next day 9:00 for whole week. 4. Assign these two profiles to the PPPoE Internet access profile. Now , the PPPoE Internet connection will follow the schedule order to perform For ce On or Force Down act[...]

Vigor2110 Series User’s Guide 155 4 4 . . 9 9 . . 4 4 U U P P n n P P The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configurati on which is already available for directly connected PC peripherals with the existing Windows 'Plug and Play' system. For NAT router[...]

Vigor2110 Series User’s Guide 156 The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your P C may cause the UPnP function not working properly. This is because these applicati ons will block the accessing ability of some network ports. Security Considerations Activating[...]

Vigor2110 Series User’s Guide 157 4 4 . . 9 9 . . 5 5 I I G G M M P P IGMP is the abbreviation of Internet Group Management Protocol . It is a communication protocol which is mainly used for managing the membership of Internet Protocol m ulticast groups. Enable IGMP Proxy Check this box to enable this function. The application of multicast will b[...]

Vigor2110 Series User’s Guide 158 Wake by Two types provide for you to wake up the binded IP . If you choose Wake by MAC Address, you have to type the correct MAC address of the host in MAC Address boxes. If you choose Wake by IP Address, you have to choose the correct IP address. IP Address The IP addresses that have been configured in Firewall&[...]

Vigor2110 Series User’s Guide 159 4 4 . . 1 1 0 0 V V P P N N a a n n d d R R e e m m o o t t e e A A c c c c e e s s s s A Virtual Private Network (VPN) is the extension of a private network that encompasses links across shared or public networks like the Intern et. In short, by VPN technolog y, you can send data between two computers across a s[...]

Vigor2110 Series User’s Guide 160 Dial-In PPP Authentication PAP Only Select this option to force the router to authenticate dial-in users with the PAP protocol. PAP or CHAP Selecting this option means the router will attempt to authenticate dial-in users with th e CHAP protocol first. If the dial-in user does not support this protocol, it will f[...]

Vigor2110 Series User’s Guide 161 There are two encapsulation methods used in IPSec, Transport and Tunnel . The Transport mode will add the AH/ESP payload and use original IP header to encapsulate the data payload only. It can just apply to local packet, e.g., L2TP over IPSec. The Tunnel mode will not only add the AH/ESP payload but also use a ne[...]

Vigor2110 Series User’s Guide 162 Set to Factory Default Click it to clear all indexes. Index Click the num ber below Index to access into the setting page of IPSec Peer Identity. Name Display the profile name of that index. Click each index to edit one peer digital certificate. There are three security levels of digital signature authentication:[...]

Vigor2110 Series User’s Guide 163 Profile Name Type in . Accept Any Peer ID Click to accept any peer regardless of its identity. Accept Subject Alternative Name Click to check one specific field of digital signature to accept the peer with matching value. The field can be IP Address, Domain, or E-mail Address . The box under the Type will appear [...]

Vigor2110 Series User’s Guide 164 Click each index to edit one remote user profile. Each Dial-In Type requires you to fill the different corresponding fields on the right. If the fields gray out, it means you may leave it untouched. The following explanation will gui de you to fill all the necessary fields. Enable this account Check the box to en[...]

Vigor2110 Series User’s Guide 165 Block – When there is conflict occurred between the hosts on both sides of VPN Tunnel in connecting, such function can block data transmission of Netbios Naming Packet inside the tunnel. User Name This field is applicable when you select PPTP or L2TP with or without IPSec policy above. Password This field is ap[...]

Vigor2110 Series User’s Guide 166 Set to Factory Default Click to clear all indexes. Name Indicate the name of the LAN-to-LAN profile. The symbol ??? represents that the profile is empty. Status Indicate the status of individual profiles. The symbol V and X represent the profile to be active and inactive, respectively. Click each index to edit ea[...]

Vigor2110 Series User’s Guide 167 Profile Name Specify a name for the profile of the LAN-to-LAN connection. Enable this profile Check here to activate this profile. Netbios Naming Packet Pass – click it to have an inquiry for data transmission between the hosts located on both sides of VPN Tunnel while connecting. Block – When there is confli[...]

Vigor2110 Series User’s Guide 168 PING to the IP Enter the IP address of the remote host that located at the other-end of the VPN tunnel. Enable PING to Keep Alive is used to handle abnormal IPSec VPN connection disruption. It will help to prov ide the state of a VPN connection for router’s judgment of redial. Normally, if any one of VPN peers [...]

Vigor2110 Series User’s Guide 169 High (ESP-Encapsulating Security Payload)- means payload (data) will be encrypted and authenticated. Select from below: DES without Authentication -Use DES encryption algorithm and not apply any authentication scheme. DES with Authentication- Use DES encryption algorithm and apply MD5 or SHA-1 authentication algo[...]

Vigor2110 Series User’s Guide 170 reused to avoid the computation complexity in phase 2. The default value is inactive this function. Local ID - In Aggressive mode, Local ID is on behalf of the IP address while identity authenticating with remote VPN server. The length of the ID is limited to 47 characters. Allowed Dial-In Type Determine the dial[...]

Vigor2110 Series User’s Guide 171 type) by checking the box. Also, you sho uld further specify the corresponding security methods on the right side. If you uncheck the checkbox , the connection type you select above will apply the authentication methods and security methods in the general settings. User Name This field is applicable when you sele[...]

Vigor2110 Series User’s Guide 172 phase 2 quick mode. More Add a static route to direct all traffic destined to more Remote Network IP Addresses/ Remote Network Mask through the VPN connection. This is usually used when you find there are several subnets behind the remote VPN router. RIP Direction The option specifies the direction of RIP (Routin[...]

Vigor2110 Series User’s Guide 173 4 4 . . 1 1 0 0 . . 7 7 C C o o n n n n e e c c t t i i o o n n M M a a n n a a g g e e m m e e n n t t You can find the summary table of all VPN connections. You may disconnect any VPN connection by clicking Drop button. You m ay also aggressively Dial-out by using Dial-out Tool and clicking Dial button. Dial Cl[...]

Vigor2110 Series User’s Guide 174 4 4 . . 1 1 1 1 C C e e r r t t i i f f i i c c a a t t e e M M a a n n a a g g e e m m e e n n t t A digital certificate works as an electronic ID, which is issued by a certification authority (CA). It contains information such as your name , a serial number, expiration dates etc., and the digital signature of t[...]

Vigor2110 Series User’s Guide 175 Type in all the information that the window requests. Then click Generate again. Import Click this button to import a saved file as the certification information. Refresh Click this button to refresh the information listed below. View Click this button to view the detailed settings for certificate request. After [...]

Vigor2110 Series User’s Guide 176 4 4 . . 1 1 1 1 . . 2 2 T T r r u u s s t t e e d d C C A A C C e e r r t t i i f f i i c c a a t t e e Trusted CA certificate lists three sets of trusted CA certificate. To import a pre-saved trusted CA certificate, please click IMPORT to open the following window. Use Browse… to find out the saved text file. [...]

Vigor2110 Series User’s Guide 177 4 4 . . 1 1 1 1 . . 3 3 C C e e r r t t i i f f i i c c a a t t e e B B a a c c k k u u p p Local certificate and Trusted CA certificate for this router can be saved within one file. Please click Backup on the following screen to save them. If you want to set encryption password for these certificates, please typ[...]

Vigor2110 Series User’s Guide 178 First, the Vigor V models of yours will have to register to a SIP Registrar by sending registration messages to validate. Then, bo th parties’ SIP proxies will forward the sequence of messages to caller to establish the session . If you both register to the same SIP Registrar, then it will be illustrated as bel[...]

Vigor2110 Series User’s Guide 179 4 4 . . 1 1 2 2 . . 1 1 D D i i a a l l P P l l a a n n This page allows you to set phone book and digit map for the VoIP function. Click the Phone Book and Digit Map links on the page to access into next pages for dialplan settings. P P h h o o n n e e B B o o o o k k In this section, you can set your VoIP conta[...]

Vigor2110 Series User’s Guide 180 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Phone Number The speed-dial number of this index. This can be any number you choose, using digits 0- 9 and * . Display Name The Caller-ID that you want to be displayed on your friend’s screen. This let your frien[...]

Vigor2110 Series User’s Guide 181 Enable Check this box to invoke this setting. Prefix Number The phone number set here is used to add, strip, or replace the OP number. Mode None - No action. Add - When you choose this mode, the OP number will be added with the prefix number for calling out through the specific VoIP interface. Strip - When you ch[...]

Vigor2110 Series User’s Guide 182 will be changed to “886311111 11” and sent to SIP server. OP Number The front number you type here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number. Min Len Set the minimal length of the dial number for appl ying the pr[...]

Vigor2110 Series User’s Guide 183 Enable Click this to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Barring Type Determine the type of the VoIP phone call, URI/URL or number. Specific URI/URL or Specific Number This field w[...]

Vigor2110 Series User’s Guide 184 For Block Unknown Domain – this function can block incomi ng calls (through Phone port) from unrecognized domain that is not specified in SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) com ing fro[...]

Vigor2110 Series User’s Guide 185 Last Call Return [Miss] Sometimes, people might miss some phone calls. Please dial number typed in this field to know where the last phone call comes from and call back to that one. Last Call Return [In] You have finished an incoming phone call, however you want to call back again for some reason. Please dial num[...]

Vigor2110 Series User’s Guide 186 Call Waiting [Act] Dial the number typed in this field to make all the incoming calls waiting for your answer. Call Waiting [Deact] Dial the number typed in this field to release this function. Block Anonymous[Act] Dial the number typed in this field to block all the incoming calls with unknown ID. Block Anonymou[...]

Vigor2110 Series User’s Guide 187 As Vigor VoIP Router is turned on, it will first register with Registrar using AuthorizationUser@Domain/Realm. After that, y our call will be bypassed by SIP Proxy to the destination using AccountName@Domain/Realm as identity. Index Click this link to access into next page for setting SIP account. Profile Display[...]

Vigor2110 Series User’s Guide 188 Profile Name Assign a name for this profile for identifying. You can t ype similar name with the domain. For example, if the domain name is draytel.org , then you might set draytel-1 in this field. Register via If you want to make VoIP call without register personal information, please choose None and check the b[...]

Vigor2110 Series User’s Guide 189 這邊的內容與 user mode 底下不同，這是對的嗎 ? SIP Port Set the port number for sending/receiving SIP message for building a session. The default value is 5060. Your peer must set the same value in his/her Registrar. Domain/Realm Set the domain name or IP address of the SIP Registrar server. Proxy [...]

Vigor2110 Series User’s Guide 190 Ring Pattern Choose a ring tone type for the VoIP phone call. 4 4 . . 1 1 2 2 . . 3 3 P P h h o o n n e e S S e e t t t t i i n n g g s s This page allows user to set phone settings fo r Phone 1 and Phone 2 respectively. However, it changes slightly according to different model you have. Phone List Port – t her[...]

Vigor2110 Series User’s Guide 191 example, sending data from the public IP of rem ote router to the private IP of local router), you can check this box to solve this problem. Dynamic RTP Port Start - Specifies the start port for RTP stream. The default value is 10050. Dynamic RTP Port End - Specifies the end port for RTP stream. The default value[...]

Vigor2110 Series User’s Guide 192 Hotline Check the box to enable it. Type in the SIP URL in the field for dialing automatically when you pick up the phone set. Session Timer Check the box to enable the function. In the limited time that you set in this field, if there is no response, the connecting call will be closed automatically. Call Forward[...]

Vigor2110 Series User’s Guide 193 Single Codec – If the box is checked, only the selected Codec will be applied. Packet Size -The amount of data contained in a single packet. The default value is 20 ms, which means the data packet will contain 20 ms voice information. Voice Active Detector - This function can detect if the voice on both sides i[...]

Vigor2110 Series User’s Guide 194 Region Select the proper region which you are located. The common settings of Caller ID Type , Dial tone , Ringing tone , Busy tone and Congestion tone will be shown automatically on the page. If you cannot find out a suitable one, please choose User Defined and fill out the corresponding values for dial tone, ri[...]

Vigor2110 Series User’s Guide 195 MISC Dial Tone Power Leve l - This setting is used to adjust the loudness of the dial tone. The smaller the number is, the louder the dial tone is. It is recommended for you to use the default setting. Ring Frequency - This setting is used to drive the frequency of the ring tone. It is recommended for you to use [...]

Vigor2110 Series User’s Guide 196 when the Refresh button is clicked. Port It shows current connection status for the port of Phone1 and Phone2. Status It shows the VoIP connection status. IDLE - Indicates that the VoIP function is idle. HANG_UP - Indicates that the connection is not established (busy tone). CONNECTING - Indicates that the user i[...]

Vigor2110 Series User’s Guide 197 The Vigor wireless routers are equipped with a wireless LAN interface compliant with the standard IEEE 802.11n draft 2 prot ocol . To boost its performance further, the Vigor Router is also loaded with advanced wireless technology to lift up data rate up to 300 Mbps*. Hence, you can finally smoothly enjoy stream [...]

Vigor2110 Series User’s Guide 198 Since WEP has been proved vulnerable, you may consider using WPA for the most secure connection. You should select the appropriate security mechanism accord ing to your needs. No matter which security suite you select, they all will enhance the over-the-air data protection and /or privacy on your wireless network[...]

Vigor2110 Series User’s Guide 199 Enable Wireless LAN Check the box to enable wireless function. Mode At present, the router can connect to Mixed (11b+11g), 11g Only, 11b Only, Mixed (11g+1 1n), 11n Only and Mixed (11b+11g+11n) stations simultaneously. Sim ply choose Mix (11b+11g+11n) m ode. Note: You should also set RADIUS Server simultaneously [...]

Vigor2110 Series User’s Guide 200 Index(1-15) Set the wireless LAN to work at certain time interval only. You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >> Schedule setup. The default setting of this field is blank and the function will always work. Hide SSID Check it to prevent from wireless sniffing a[...]

Vigor2110 Series User’s Guide 201 Packet-OVERDRIVE This feature can enhance the performance in data transmission about 40%* m ore (by checking Tx Burs t). It is active only when both sides of Access Point and Station (in wireless client) invoke this function at the same time. That is, the wireless client must support this feature and invoke the f[...]

Vigor2110 Series User’s Guide 202 Mode There are several modes provided for you to choose. Disable - Turn off the encryption mechanism. WEP- Accepts only WEP clients and the encryption key should be entered in WEP Key. WPA/PSK- Accepts only WPA clients and the encryption key should be entered in PSK. WPA2/PSK- Accepts only WPA2 clients and the en[...]

Vigor2110 Series User’s Guide 203 128-Bit - For 128 bits WEP key, either 13 ASCII characters, such as ABCDEFGHIJ KLM (or 26 hexadecimal digits leading by 0x, such as 0x4142434445464 748494A4B4C4D). All wireless devices must support the same WEP encryption bit size and have the same key . Four keys can be entered here, but only one key can be sele[...]

Vigor2110 Series User’s Guide 204 Add Add a new MAC address into the list. Delete Delete the selected MAC address in the list. Edit Edit the selected MAC address in the list. Cancel Give up the access control set up. OK Click it to save the access control list. Clear All Clean all entries in the MAC address list . 4 4 . . 1 1 3 3 . . 5 5 W W P P [...]

Vigor2110 Series User’s Guide 205 z If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN code of the wireless clie nt you wish to connect to the vigor router. For WPS is supported in WPA-PSK or WPA2-PSK mode, if you do not choose such mode in Wireless LAN>>Security , you will see the [...]

Vigor2110 Series User’s Guide 206 SSID Display the SSID1 of the router. WPS is supported by SSID1 only. Authentication Mode Display current authentication mode of the router. Only WPA2/PSK and WPA/PSK support WPS. Configure via Push Button Click Start PBC to invoke Push-Button style WPS setup procedure. The router will wait for WPS requests from [...]

Vigor2110 Series User’s Guide 207 The application for the WDS-Repeater mode is depicted as below: The major difference between these two modes is that: while in Repeater mode, the packets received from one peer AP can be repeated to another peer AP through WDS links. Yet in Bridge mode, packets received from a WDS link will only be for warded to [...]

Vigor2110 Series User’s Guide 208 Click WDS from Wireless LAN menu. The following page will be shown. Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulfill the[...]

Vigor2110 Series User’s Guide 209 first type of application. Repea ter mode is for the second one. Security There are three ty pes for security, Disable , WEP and Pre-shared key . The setting you choose here will make the following WEP or Pre-shared key field valid or not. Choose one of the types for the router. WEP Check this box to use the same[...]

Vigor2110 Series User’s Guide 210 not have protection mechanism to avoid the conflict with neighboring devices of 802.11a/b/g. Channel Bandwidth 20- the router will use 20Mhz for data transmission and receiving between the AP and the stations. 20/40 – the router will use 20Mhz or 40Mhz for data transmission and receiving according to the statio[...]

Vigor2110 Series User’s Guide 211 APSD Capable The default setting is Disable . Aifsn It controls how long the client waits for each data transmission. Please specify the value ranging from 1 to 15. Such parameter will influence the time delay for WMM accessing categories. For the service of voice or video image, please set small value for AC_VI [...]

Vigor2110 Series User’s Guide 212 Scan It is used to discover all the connected AP. The results will be shown on the box above this button. Statistics It displays the statistics for the channels used by APs. Add to If you want the found AP applying the WDS settings, please type in the AP’s MAC address on the bottom of the page and click Bridge [...]

Vigor2110 Series User’s Guide 213 Refresh Click this button to refresh the status of station list. Add Click this button to add current typed MAC address into Access Contro l.[...]

Vigor2110 Series User’s Guide 214 4 4 . . 1 1 4 4 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: Status, Administrator Password, Configuration Backup, Syslog, Time setup, Reboot System, Firmware Upgrade. Below shows the menu items fo[...]

Vigor2110 Series User’s Guide 215 DHCP Server Display the current status of DHCP server of the LAN interface. DNS Display the assigned IP address of the primary DNS. WAN------- Link Status Display current connection status. MAC Address Display the MAC address of the WAN Interface. Connection Display the connection type. IP Address Display the IP [...]

Vigor2110 Series User’s Guide 216 ACS Server URL/Username/Password – Such data must be typed according to the ACS ( Auto Configuration Server) you want to link. Please refer to Auto Configuration Server user’s manual for detailed information. CPE Client It is not necessary for you to type them. Such information is useful for Auto Configuratio[...]

Vigor2110 Series User’s Guide 217 2. Click Backup button to get into the following dialog. Click Save button to open another dialog for saving configuration as a file. 3. In Save As dialog, the default filename is config.cfg . You could gi ve it another name by yourself. 4. Click Save button, the configuration will download a utomatically to your[...]

Vigor2110 Series User’s Guide 218 Note: Backup for Certification must be done independently . The Configuration Backup does not include information of Certificate. R R e e s s t t o o r r e e C C o o n n f f i i g g u u r r a a t t i i o o n n 1. Go to System Maintenance >> Configuration Backup . The following windows will be popped-up, as [...]

Vigor2110 Series User’s Guide 219 Enable syslog message Check the box listed on this web page to send the corresponding message of firewall, VPN, User Access, Call, WAN, Router/DSL information to Syslog. Enable (Alert Setup…) Check “ Enable ” to activate function of mail alert. Send a test e-mail Make a simple test for the e-mail address sp[...]

Vigor2110 Series User’s Guide 220 4 4 . . 1 1 4 4 . . 6 6 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Current System Time Click Inquire Time to get the current time. Use Browser Time Select this option to use the browser time from the remote administrator PC host as ro[...]

Vigor2110 Series User’s Guide 221 4 4 . . 1 1 4 4 . . 7 7 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the setti ngs for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The default value is 50[...]

Vigor2110 Series User’s Guide 222 Set Community Set community by typing a proper nam e. The default setting is private. Manager Host IP Set one host as the manager to execute SNMP function. Please type in IP address to specify certain host. Trap Community Set trap community by typing a pr oper name. The default setting is public. Notification Hos[...]

Vigor2110 Series User’s Guide 223 4 4 . . 1 1 4 4 . . 9 9 F F i i r r m m w w a a r r e e U U p p g g r r a a d d e e Before upgrading your router firmware, you need to i nstall the Router Tools. The Firmware Upgrade Utility is included in the tools. The following web page will guide you to upgrade firmware by using an exam ple. Note that this ex[...]

Vigor2110 Series User’s Guide 224 4 4 . . 1 1 5 5 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics. 4 4 . . 1 1 5 5 . . 1 1 D D i i a a l l - - o o u u t t T T r r i i g g g g e e r r Click Diagnostics and click Dial-ou[...]

Vigor2110 Series User’s Guide 225 4 4 . . 1 1 5 5 . . 2 2 R R o o u u t t i i n n g g T T a a b b l l e e Click Diagnostics and click Routing Table to open t he web page. Refresh Click it to reload the page. 4 4 . . 1 1 5 5 . . 3 3 A A R R P P C C a a c c h h e e T T a a b b l l e e Click Diagnostics and click ARP Cache Table to view the content [...]

Vigor2110 Series User’s Guide 226 4 4 . . 1 1 5 5 . . 4 4 D D H H C C P P T T a a b b l l e e The facility provides information on IP address as signments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Index It displays the connection ite[...]

Vigor2110 Series User’s Guide 227 Private IP:Port It indicates the source IP address and port of local PC. #Pseudo Port It indicates the temporary port of the router used for NAT. Peer IP:Port It indicates the destination IP address and port of remote host. Interface It displays the representing number for different interface. Refresh Click it to[...]

Vigor2110 Series User’s Guide 228 TX rate (kbps) Display the transmission speed of the monitored device. RX rate (kbps) Display the receiving speed of the monitored device. Sessions Display the session number that you specified in Limit Session web page. Action Block - can prevent specified PC acce ssing into Internet within 5 minutes. Unblock ?[...]

Vigor2110 Series User’s Guide 229 Clear Click this link to remove the result on the window. 4 4 . . 1 1 5 5 . . 8 8 T T r r a a c c e e R R o o u u t t e e Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run [...]

Vigor2110 Series User’s Guide 230[...]

Vigor2110 Series User’s Guide 231 5 A A p p p p l l i i c c a a t t i i o o n n a a n n d d E E x x a a m m p p l l e e s s 5 5 . . 1 1 C C r r e e a a t t e e a a L L A A N N - - t t o o - - L L A A N N C C o o n n n n e e c c t t i i o o n n B B e e t t w w e e e e n n R R e e m m o o t t e e O O f f f f i i c c e e a a n n d d H H e e a a d d [...]

Vigor2110 Series User’s Guide 232 have known. 3. Go to LAN-to-LAN . Click on one index number to edit a profile. 4. Set Common Settings as shown below. You should enable both of VPN connections because any one of the parties may start the VPN connection. 5. Set Dial-Out Settings as shown below to dial to connect to Router B aggressively with the [...]

Vigor2110 Series User’s Guide 233 If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, PPP Authentication and VJ Compression for this Dial-Out connection. 6. Set Dial-In settings to as shown below to allow Router B dial-in to build VPN connection. If an IPSec-based service i s selected, yo[...]

Vigor2110 Series User’s Guide 234 If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. 7. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router A can direct the packets destined to the remote network to Router B [...]

Vigor2110 Series User’s Guide 235 For using IPSec-based service, such as IPSec or L2TP with IPSec Policy, you have to set general settings in IPSec General Setup , such as the pre-shared key that both parties have known. 3. Go to LAN-to-LAN . Click on one index number to edit a profile. 4. Set Common Settings as shown below. You should enable bot[...]

Vigor2110 Series User’s Guide 236 If a PPP-based service is selected, y ou should further specify the remote peer IP Address, Username, Password, PPP Authentication and VJ Compression for this Dial-Out connection. 6. Set Dial-In settings to as shown below to allow Router A dial-in to build VPN connection. If an IPSec-based service is selected, y [...]

Vigor2110 Series User’s Guide 237 If a PPP-based service is selected, y ou should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. 7. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router B can direct the packets destined to the remote network to Router A[...]

Vigor2110 Series User’s Guide 238 5 5 . . 2 2 C C r r e e a a t t e e a a R R e e m m o o t t e e D D i i a a l l - - i i n n U U s s e e r r C C o o n n n n e e c c t t i i o o n n B B e e t t w w e e e e n n t t h h e e T T e e l l e e w w o o r r k k e e r r a a n n d d H H e e a a d d q q u u a a r r t t e e r r The other common case is that [...]

Vigor2110 Series User’s Guide 239 3. Go to Remote Dial-In User . Click on one index number to edit a profile. 4. Set Dial-In settings to as shown below to allow the remote user dial-in to build VPN connection. If an IPSec-based service is sele cted, you may further specify the remote peer IP Address, IKE Authentication Method and I PSec Security [...]

Vigor2110 Series User’s Guide 240 Settings in the remote host: 1. For Win98/ME, you may use "Dial-up Networking" to create the PPTP tunnel to Vigor router. For Win2000/XP, please use "Network and Dial-up connections" or “Smart VPN Client”, complimentary software to help you create PPTP, L2TP, and L2TP over IPSec tunnel. Yo[...]

Vigor2110 Series User’s Guide 241 You may further specify the method you use to get IP, the security method, and authentication method. If the Pre-Shared Key is selected, it should be consistent with the one set in VPN router. If a PPP-based service is selected, you should fu rther specify the remote VPN server IP address, Username, Password, and[...]

Vigor2110 Series User’s Guide 242 4. Click Connect button to build connection. When the connection is successful, you will find a green light on the right down corner. 5 5 . . 3 3 Q Q o o S S S S e e t t t t i i n n g g E E x x a a m m p p l l e e Assume a teleworker someti mes works at hom e and takes care of children. When working time, he woul[...]

Vigor2110 Series User’s Guide 243 3. Return to previous page. Enter th e Name of Index Class 1 by clicking Edit link. T y pe the name “ E-m ail ” for Class 1. 4. For this index, the user will set reserved bandwidth (e.g., 25%) for E-mail using protocol POP3 and SMTP .[...]

Vigor2110 Series User’s Guide 244 5. Return to previous page. Enter th e Name of Index Class 2 by clicking Edit link. In this index, the user will set reserved bandwidth for HTTPS . And click OK . 6. Click Setup link for W AN. 7. Check Enable UDP Band width Control on the bott om to prevent enormous UDP traf fic of V oIP influent other applicatio[...]

Vigor2110 Series User’s Guide 245 9. Click Edit to open the following window . Check the ACT box, first. 10. Then click Edit of Local Address to set a worker ’ s subnet address. Click Edit of Remote Address to set headquarter ’ s IP address. Leave other fields and click OK . 5 5 . . 4 4 L L A A N N – – C C r r e e a a t t e e d d b b y y [...]

Vigor2110 Series User’s Guide 246 Y ou can just set the settings wrapped inside the red rectangles to fit the request of NA T usage. T o use another DHCP server in the network rather than the built-in one of V igor Router , you have to change the settings as show below .[...]

Vigor2110 Series User’s Guide 247 Y ou can just set the settings wrapped inside the red rectangles to fit the request of NA T usage.[...]

Vigor2110 Series User’s Guide 248 5 5 . . 5 5 C C a a l l l l i i n n g g S S c c e e n n a a r r i i o o f f o o r r V V o o I I P P F F u u n n c c t t i i o o n n 5 5 . . 5 5 . . 1 1 C C a a l l l l i i n n g g v v i i a a S S I I P P S S e e v v e e r r Example 1: Both John and David have SIP Addresses from different servi ce providers. John?[...]

Vigor2110 Series User’s Guide 249 Example 2: Both John and David have SIP Addresses from the same servi ce provider. John’s SIP URL: 1234@draytel.org , David ’s SIP URL: 4321@draytel.org Settings for John DialPlan index 1 Phone Number: 1111 Display Name: David SIP URL: 4321@draytel.org SIP Accounts Settings --- Profile Name: draytel 1 Registe[...]

Vigor2110 Series User’s Guide 250 5 5 . . 5 5 . . 2 2 P P e e e e r r - - t t o o - - P P e e e e r r C C a a l l l l i i n n g g Example 3: Arnor and Paulin have Vigor routers respectively. The y can call each other without SIP Registrar. First they must have each other’s IP address and assign an Account Name for the port used for calling. Arn[...]

Vigor2110 Series User’s Guide 251 5 5 . . 6 6 U U p p g g r r a a d d e e F F i i r r m m w w a a r r e e f f o o r r Y Y o o u u r r R R o o u u t t e e r r Before upgrading your router firmware, you need to i nstall the Router Tools. The Firmware Upgrade Utility is included in the tools. 1. Insert CD of the router to your CD ROM. 2. From the we[...]

Vigor2110 Series User’s Guide 252 9. Double click on the icon of router tool. The setup wizard will appear. 10. Follow the onscreen instructions to install the tool. Finally , click Finish to end the installation. 11. From the Start menu, open Programs and choose Router Tools XXX >> Firmware Upgrade Utility . 12. Type in your router IP, usu[...]

Vigor2110 Series User’s Guide 253 14. Click Send . 15. Now the firmware update is finished.[...]

Vigor2110 Series User’s Guide 254 5 5 . . 7 7 R R e e q q u u e e s s t t a a c c e e r r t t i i f f i i c c a a t t e e f f r r o o m m a a C C A A s s e e r r v v e e r r o o n n W W i i n n d d o o w w s s C C A A S S e e r r v v e e r r 1. Go to Certificate Management and choose Local Certificate .[...]

Vigor2110 Series User’s Guide 255 2. You can click GENERATE button to start to edit a certificate request. Enter the information in the certificate request. 3. Copy and save the X509 Local Certificate Requet as a text file and save it for later use. 4. Connect to CA server via web browser. Follo w the i nstruction to submit the request. Below we [...]

Vigor2110 Series User’s Guide 256 Select Advanced request . Select Submit a certificate request a base64 encoded PKCS #10 file or a renewal request using a base64 encoded PKCS #7 file Import the X509 Local Certificate Requet text file. Select Router (Offline request) or IPSec (Offline request) below. Then you have done the request and the ser ver[...]

Vigor2110 Series User’s Guide 257 you will find the below window showin g “------BEGINE CERTIFICATE------.....” 6. You may review the detail informati on of the certificate by clicking View button.[...]

Vigor2110 Series User’s Guide 258 5 5 . . 8 8 R R e e q q u u e e s s t t a a C C A A C C e e r r t t i i f f i i c c a a t t e e a a n n d d S S e e t t a a s s T T r r u u s s t t e e d d o o n n W W i i n n d d o o w w s s C C A A S S e e r r v v e e r r 1. Use web browser connecting to the CA server that you would like to retrieve its CA cert[...]

Vigor2110 Series User’s Guide 259 2. In Choose file to download , click CA Certificate Current and Base 64 encoded, and Download CA certificate to save the .cer. file. 3. Back to Vigor router, go to Trusted CA Certificate . Click IMPORT button and browse the file to import the certificate (.cer file) in to Vigor router. When finished, click refre[...]

Vigor2110 Series User’s Guide 260[...]

Vigor2110 Series User’s Guide 261 T T r r o o u u b b l l e e S S h h o o o o t t i i n n g g This section will guide you to solve abnormal s ituations if you cannot access into the Internet after installing the router and finishing the we b configuration. Please follow sections below to check your basic installation status stage by stage. z Chec[...]

Vigor2110 Series User’s Guide 262 6 6 . . 2 2 C C h h e e c c k k i i n n g g I I f f t t h h e e N N e e t t w w o o r r k k C C o o n n n n e e c c t t i i o o n n S S e e t t t t i i n n g g s s o o n n Y Y o o u u r r C C o o m m p p u u t t e e r r I I s s O O K K o o r r N N o o t t Sometimes the link failure occurs due to the wrong network[...]

Vigor2110 Series User’s Guide 263 4. Select Obtain an IP address automatically and Obtain DNS server address automatically . F F o o r r M M a a c c O O s s 1. Double click on the current used MacOs on the desktop. 2. Open the Application folder and get into Network . 3. On the Network screen, select Using DHCP from the drop down list of Configur[...]

Vigor2110 Series User’s Guide 264 6 6 . . 3 3 P P i i n n g g i i n n g g t t h h e e R R o o u u t t e e r r f f r r o o m m Y Y o o u u r r C C o o m m p p u u t t e e r r The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most import[...]

Vigor2110 Series User’s Guide 265 6 6 . . 4 4 C C h h e e c c k k i i n n g g I I f f t t h h e e I I S S P P S S e e t t t t i i n n g g s s a a r r e e O O K K o o r r N N o o t t Click Internet Access group and then check whether the ISP settings are set correctly. F F o o r r P P P P P P o o E E U U s s e e r r s s 1. Check if the Enable opti[...]

Vigor2110 Series User’s Guide 266 2. Check if WAN IP Network Settings is set appropriately. 3. Check if IP Address, Subnet Mask and Gateway are set correctly (must identify with the values from your ISP) if you choose Specify an IP address . F F o o r r P P P P T T P P U U s s e e r r s s 1. Check if the Enable option for PPTP Link is selected. 2[...]

Vigor2110 Series User’s Guide 267 3. Check if WAN IP Network Settings are set properly. If you select Specify an IP address , you have to type in the values of IP Address and Subnet Mask manually. Be sure the values that you type identify with the values from your ISP. 6 6 . . 5 5 B B a a c c k k i i n n g g t t o o F F a a c c t t o o r r y y D [...]

Vigor2110 Series User’s Guide 268 6 6 . . 6 6 C C o o n n t t a a c c t t i i n n g g Y Y o o u u r r D D e e a a l l e e r r If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.[...]