Enterasys Networks 4H4203-72 manual

7.5x9-inch cover with bleed on 4 sides Enterasys Matrix ® DFE-Gold Series Hardware Installation Guide Module 4H4282-49 Module 4H4283-49 Module 4H4203-72 Module 4H4202-72 Module 4H4284-49 P/N 9033906-05[...]

[...]

i Notice Enterasys Networks  reserv es  the  right  to  make  changes  in  specif ications  and  other  info rmation  contained  in  this  document  and  its  web  site  without  prior  notice.  The  reader  should  in  all  cases  consult  Enterasy s Networks[...]

ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This  device  com plies  with  Par t  15  of  th e  FCC  rules.  Operat ion  is  subject  to  the  foll owing  tw o  conditions:  (1)  this  device  may  not  cause  harmful  interference, ?[...]

iii Electromagnetic Compatibility (EMC) This  product  complies  with  the  follo wing:  47  CFR  Par t s  2  and  15,  CSA  C108.8,  2004/108/EC,  EN  55022,  EN  61000 ‐ 3 ‐ 2,  EN 61000 ‐ 3 ‐ 3,  EN  55024,  AS/NZS  CISPR  22,  VCCI  V ‐ 3.  Compatibilidad[...]

iv Enterasys  Customer  Support  at  353  61  705586  (Ireland). ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼៪ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 &U   ໮⒈㘨㣃 3%% ໮⒈Ѡ㣃䝮 [...]

v VCCI Notice This  is  a  class  A  product  based  on  the  standard  of  the  Vo l u n t a r y  Control  Co uncil  for  Interfe rence  by  Information  Te c h n o l o g y  Equipment  (VCCI).  If  this  equipmen t  is  used  in  a  domestic  environment, [...]

vi Safety Information Class 1 Laser Transceivers The single mode interface modules use Class 1 laser transceivers . Read the following safe ty information before installing or operating these m odules. The  Class  1  laser  transceivers  use  an  optical  feedback  loop  to  maintain  Class  1  operation ?[...]

vii ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This  document  is  an  agreement  (“ Agreement”)  betwee n  the  end  user  (“Y o u”)  and  Enteras ys  Networks,  In c.,  on  behalf  of  its[...]

viii 3. APPLICABLE  LAW. This  Agreem ent  shall  be  interpreted  and  governed  under  the  laws  and  in  the  state  and  federal  courts  of  th e  Commonwealth  of  Massachu setts  with out  regard  to  its  conflicts  of  laws  provis ions.  You  [...]

ix 8. AUDIT  RIGHTS. You  here by  acknowled ge  that  the  intellectual  property  rights  associated  with  the  Program  are  of  critical  value  to  Enterasys,  and,  accordingly,  You  hereby  agree  to  maintain  complete  books,  re cords  and  account[...]

x[...]

xi Contents About This Guide Who Should Use This G uide .............. ....................... ....................... ......................... ................ .......... xv How to Use This Guide ................ ....................... ...................... ....................... ..................... ........ ..... xvi Related Documents .....[...]

xii Connecting to COM Port for Local Management ................... ....................... ...................... ............. 3-20 What Is Needed ..... ...................... .................... ...................... ....................... .................... ...... ... 3-20 Connecting to an IBM PC or Co mpatible Device .......... ..........[...]

xiii Figures 1-1 4H4282-49, 4H4283-49, and 4H4203-72 DFE-Gold Modules .................... ...................... ............ 1-4 1-2 4H4202 -72 and 4H4284-49 DFE-Gold Modules . ....................... ...................... ....................... ..... 1-5 3-1 Examples, Slot Numbers/Module Placement in Ma trix E7 Chassis .................... ...[...]

xiv Tables 3-1 Contents of DFE-Gold Module Carton .............. ...... .................... ...................... ....................... ..... 3-2 4-1 LANVIEW LEDs ......... ....................... ...................... ....................... ...................... ............. ............ 4-5 4-1 Troubleshooting Checklist ... ... ..........[...]

Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide xv About This Guide This  guide  provides  an  ov erview ,  installation  and  troubleshooting  instructions,  and  specifications  for  the  Enterasys  Matr ix ®  DFE ‐ Gold  4H42 82 ‐ 49,  4H4283 ‐ 49,  4H4203 ‐ 72, [...]

How to Use This Guide xvi About This Guide How to Use This Guide This  preface  provides  an  overview  of  this  guide  and  the  DFE ‐ Gold  Series  manual  set,  and  a  brief  summary  of  each  chapter;  de fines  the  conv entions  used  in  this  document; [...]

Conventions Used in This Guide Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide xvii Conventions Used in This Guide The  following  conventions  are  used  in  this  guide: Lowercase  x :  Indicates  the  general  use  of  an  alphanumeric  character  (for  example,  6x1xx[...]

Getting Help xviii About This Guide Getting Help For  additional  support  related  to  the  modules  or  this  document,  contact  Enterasys Networks  using  one  of  the  following  metho ds: Before  contacting  Enterasys Networks  for  technical  support,  have  the  foll[...]

Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 1-1 1 Introduction This  chapter  provides  an  overview  of  the  DFE ‐ Gold  module  capabilities,  and  introduces  the  4H4282 ‐ 49,  4H428 3 ‐ 49,  4H4203 ‐ 72,  4H 4202 ‐ 72,  and  4H4284 ‐ 49  DFE ‐ Gold[...]

The DFE-Gold Modules 1-2 Introduction • Support  for  a  var i et y  of  converged  applications  including  Vo I P  with  Po we r ‐ over ‐ Ethernet  The DFE-Gold Modules This  section  provides  an  overview  of  the  4H4282 ‐ 49,  4H4283 ‐ 49,  4H4203 ‐ 72  ( Figure 1 ‐ [...]

The DFE-Gold Modules Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 1-3 full ‐ duplex  mode  of  operation.  The  duplex  mode  can  be  determined  by  either  auto ‐ negotiation  or  manual  configuration.  4H4202-72 The  4H4202 ‐ 72  has  72,  10BASE ‐ T/10[...]

The DFE-Gold Modules 1-4 Introduction Figure 1- 1 4H4282-49, 4H4283-49, and 4H4203- 72 DFE-Gold Modules 1 OFFLINE/RESET button 6 GROUP status LEDs 2 RJ45 COM (Console Port) 7 GROUP select LEDs 3 CPU LED 8 4H4282-49 / 4H4283-49 - N EM option slot 4 MGMT LED 4H4203-72 - Ports (1-72), 10/100, through six RJ21s 5 GROUP SELECT button 9 4H4282-49 - Ports[...]

The DFE-Gold Modules Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 1-5 Figure 1-2 4H4202-72 and 4H4284-49 DF E-Gold Modul es 1 OFFLINE/RESET switch 6 GROUP select LEDs 2 RJ45 COM (Console Port) 7 GROUP SELECT button 3 CPU LED 8 GROUP status LEDs 4 MGMT LED 9 4H4202-72 - Groups 1&2, 48 Ports, 10/100, through RJ45s 4H4284-4[...]

Connectivity 1-6 Introduction Connectivity 4H4282-49 Depending  on  how  the  4H4282 ‐ 49  ( Figure 1 ‐ 1 )  is  configured,  it  can  support  up  to: • 48,  10BASE ‐ T/100BASE ‐ TX  swi tched  ports  connected  through  48  fixed,  RJ45  front ‐ panel  connectors,  o[...]

Management Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 1-7 Management Management  of  the  module  can  be  either  in ‐ band  or  out ‐ of ‐ band.  In ‐ band  remote  management  is  possible  us ing  Te l n e t ,  Enterasys Networks’  NetSight ®  man agem[...]

LANVIEW Diagnostic LEDs 1-8 Introduction •N e t w o r k  Services  are  logical  groups  of  Classification  Rules  that  identify  specific  networked  applic ations  or  services .  Users  may  be  permitted  or  denied  access  to  these  services  based  on  thei[...]

Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide 2-1 2 Network Requirements Before  inst alling  the  module,  review  the  requirements  and  specificat ions  referred  to  in  this  chapter  concerning  the  following: • 10BASE ‐ T  Netw ork  (page 2 ‐ 1) • 100BASE [...]

100BASE-TX Network 2-2 Network Requirements 100BASE-TX Network Fixed  front  panel  ports  of  the  4H4282 ‐ 49,  4H4283 ‐ 49,  4H4203 ‐ 72,  and  4H4202 ‐ 72 provide  a  connection  that  supports  Category  5  UTP  cabling.  The  device  at  the  other  end  of [...]

Matrix DFE-Gold Series Modules Hardware Installation Guide 3-1 3 Installation This  chapter  provides  the  instructions  to  install  the  4H4282 ‐ 49,  4H4283 ‐ 49,  4H4203 ‐ 72,  4H4202 ‐ 72,  and  4H4284 ‐ 49 DFE ‐ Gold modules. Follow  the  order  of  the  sections  li sted ?[...]

Installation Site Requirement 3-2 Installation Inst allation Site Requirement The  DFE ‐ Gold module  must  be  installed  in  a  Matrix  E7,  N1,  N3,  N5,  or  N7  chassis  located  in  a  Restricted  Access  Location  (RAL).  This  location  should  only  be  acce[...]

Installing Optional Netw ork Expansion Module Matrix DFE-Gold Series Modules Hardware Installation Guide 3-3 Inst alling Optional Network Exp ansion Module A  Phillips  screwdriver  is  required  to  ins tall  an  optional  netw ork  expansion  module  into  the  4H4282 ‐ 49,  4H428 3 ‐ 49,  or ?[...]

DFE Module Placement and Installation Rules 3-4 Installation To  ensure  proper  operation  of  the  system,  consider  the  following  examples  and  rules  for  module  placement  in  either  chassis. Example 1 ( Figure 3-1 , A) Shows  one  module  installed  in  the  chassis[...]

Installing Module into a Chassis Matrix DFE-Gold Series Modules Hardware Installation Guide 3-5 Example 3 ( Figure 3-1 , C) Shows  the  primary  management  module  missing  from  slot  1.  As  long  as  the  module  installed  in  slot  2  is  designated  as  a  re dundant  manag[...]

Installing Module into a Chassis 3-6 Installation Prep aration 1. Remove  the  blank  pan el  cov ering  the  slot  in  which  the  module  will  be  installed.  All  other  slots  must  remain  cov ered  to  ensure  proper  airflow  for  cooling.  (Save  the  blank[...]

Installing Module into a Chassis Matrix DFE-Gold Series Modules Hardware Installation Guide 3-7 2. Align  the  module  card  between  the  upper  and  lower  card  guides  of  the  desired  slot  and  slide  it  into  the  chassis,  taking  care  that  the  module  slides[...]

Installing Module into a Chassis 3-8 Installation Figure 3-2 Inst alling Module into Matr ix E7 or N7 Chassis (Matrix E7 shown) 1 Card guides 5 Upper/lower locking tabs (in proper open position) 2 Slot number 1(right-most slot is 7) 6 Upper/lower locking tab (in clo sed position) 3 Module card 7 Backplane connectors (power and FTM2) 4 Metal back p [...]

Installing Module into a Chassis Matrix DFE-Gold Series Modules Hardware Installation Guide 3-9 Inst alling Module into Matr ix N1, N3, or N5 Chassis A  DFE ‐ Gold module  can  be  installed  in  any  av ailable  chassis  sl ot  (1  through  3)  in  the  Matrix N3  chassis  or  slots  1 [...]

Connecting to the Network 3-10 Installation Connecting to the Network For  connecting  unshielded  twisted  pair  (UTP )  segments  from  the  network  or  other  devices,  refer  to • Connecting  UTP  Cables  to  4H4282 ‐ 49  or  4H4202 ‐ 72  (page 3 ‐ 11) • Connecting  UT[...]

Connecting to the Network Matrix DFE-Gold Series Modules Hardware Installation Guide 3-11 Connecting UTP Cables to 4H4282-49 or 4H4202-72 The  fixed  RJ4 5  front  panel  connections  of  the  4H4282 ‐ 49  and  4H4202 ‐ 72  are  10/100  Mbps  ports.  The  ports  have  internal  crossov er[...]

Connecting to the Network 3-12 Installation 3. V erify  that  a  link  ex ists  by  check ing  that  the  port  RX  (Receive )  LED  is  ON  (flashi ng  amber ,  blinking  green,  or  solid  green).  If  the  RX  LED  is  OFF  and  the  TX  (T ransmit)  [...]

Connecting to the Network Matrix DFE-Gold Series Modules Hardware Installation Guide 3-13 Figure 3-5 Four-Wire Crossover Cable RJ45 Pinout s, Connections Between Hub Devices 1 RJ45 device port 3 RJ45-to-RJ45 crossover cable 2 Other device port 4 RX+/RX- and TX+/TX- connections. These connections must share a common color pair . Figure 3-6 Four-Wire[...]

Connecting to the Network 3-14 Installation Figure 3-7 Eight-Wire Crossover Cable RJ45 Pin outs , Connections Between Hub Devices 1 RJ45 device port 3 RJ45-to-RJ45 crossover cable 2 Other device port Figure 3-8 Eight-Wire Straight -Throu gh Cable RJ45 Pinout s, Connections Between Sw itches and End-Use r Devices 1 RJ45 device port 3 RJ45-to-RJ45 st[...]

Connecting to the Network Matrix DFE-Gold Series Modules Hardware Installation Guide 3-15 e. Ensure  that  the  twisted  pai r  connection  meets  the  dB  loss  and  cable  specifications  outlined  in  the  Cabling  Guide.  Refer  to   “Related  Documents”  on  page xvi ?[...]

Connecting to the Network 3-16 Installation 3. T o  install  an  RJ21  right ‐ angle  connector ,  refer  to  Fi gure 3 ‐ 10  and  proceed  as  follows: a. If  using  an  optional  RJ21  angle  adapter  available  from  Enterasys  Networks,  insert  the  angle  adapte[...]

Connecting to the Network Matrix DFE-Gold Series Modules Hardware Installation Guide 3-17 Figure 3-10 Connection Using Optional RJ21 Angle Adapter 1 RJ21 angle adapter 5 Retaining clips 2 RJ21 port connector 6 GROUP SELECT button 3 Retaining screws 7 Example showing how multiple cables would be arranged along the front panel. 4 RJ21 right-angled co[...]

Connecting to the Network 3-18 Installation 4. V erify  that  a  link  ex ists  by  check ing  that  the  port  RX  (Receive )  LED  is  ON  (flashi ng  amber ,  blinking  green,  or  solid  green).  If  the  RX  LED  is  OFF  and  the  TX  (T ransmit)  [...]

Connecting to the Network Matrix DFE-Gold Series Modules Hardware Installation Guide 3-19 2. Insert  the  MT ‐ RJ  cable  connector  into  the  MT ‐ RJ  front  panel  connector  until  it  clicks  into  place. Figure 3-1 1 Connecting a Fiber-Optic Segment to MT -RJ Front Panel Connector Note: Leave t[...]

Connecting to COM Port for Local Management 3-20 Installation 1. V erify  that  a  link  ex ists  by  check ing  that  the  port  RX  LED  is  ON  (flashing  amber ,  blinking  green,  or  solid  green).  If  the  RX  LED  is  OFF  and  the  TX  LED  is [...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Modules Hardware Installation Guide 3-21 Wi th  a  UTP  straight ‐ through  cab le  and  RJ45 ‐ to ‐ DB25  female  ad apter ,  yo u  can  connect  products  equipped  with  an  RJ45  COM  port  to  a  VT  se rie[...]

Connecting to COM Port for Local Management 3-22 Installation Connecting to a VT Series T erminal To  connect  a  VT  Series  terminal  to  an  Enterasys Netw orks  DFE ‐ Gold module  COM  port  ( Figure 3 ‐ 13 ),  use  a  UTP  straight ‐ through  cable  with  RJ45  connectors  an[...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Modules Hardware Installation Guide 3-23 When  these  parameters  are  set,  the  Local  Management  password  screen  will  display .  Refer  to  the  Enterasys  Matrix  DFE ‐ Gold  Series  Configuration  Guide  for ?[...]

Connecting to COM Port for Local Management 3-24 Installation 5. With  a  PC  connected  to  a  remote  mo dem,  you  can  configure  th e  switch  remotely .  To  accomplish  this,  you  must  configure  you r  PC  VT  emulation  package  with  the  following  para[...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Modules Hardware Installation Guide 3-25 Adapter Wiring and Signal Assignment s COM Port Adapter Wiring and Sign al Diagram RJ45 DB9 Pin Conductor Pin Signal 1 Blue 2 Receive (RX) 4 Red 3 T ransmit (TX) 5 Green 5 Ground (GRD) 2 Orange 7 R equest to Send (RTS) 6 Y ellow 8 Clear to Se[...]

Completing the Installation 3-26 Installation Completing the Inst allation Completing  the  DFE  module  installat ion  depends  on  if  the  module  is  being  installed  in: •a  new  DFE  module  syst em  (refer  to  “Completing  the  Installation”  on  page 3 ‐ 26), [...]

Completing the Installation Matrix DFE-Gold Series Modules Hardware Installation Guide 3-27 First-T ime Log-In Using a Console Port Connection Start  the  Command  Line  Interface  (CLI)  from  the  module’ s  local  console  port  as  follo ws: 1. Connect  a  terminal  to  the  local  cons[...]

Completing the Installation 3-28 Installation Completing the Inst allation of a DFE-Gold Module in an Existing System In  an  established  DFE ‐ Gold module  system, •a  DFE ‐ Gold module  is  already  established  as  the  management  module, •t h e  passwords  hav e  alrea dy  been  set ?[...]

Completing the Installation Matrix DFE-Gold Series Modules Hardware Installation Guide 3-29 Logging in with an Administrati vely-Configured User Account If  the  device’ s  default  user  account  settings  have  been  changed,  proceed  as  follows: 1. At  the  login  prompt,  enter  your  ad[...]

Completing the Installation 3-30 Installation[...]

Matrix DFE-Gold Series Modules Hardware Installation Guide 4-1 4 T roubleshooting This  chapter  provides  information  concerning  the  following: • Using  LANVIEW  (page 4 ‐ 1) • T roubleshooting  Checklist  (page 4 ‐ 7) • Overview  of  DF E ‐ Gold  Module  Shutdown  Procedure  (page 4 ?[...]

Using LANVIEW 4-2 Troubleshooting Viewing Receive/T ransmit Activi ty on 4H4282-49, 4H4283-49, and 4H4203-72 On  the  4H4282 ‐ 49,  4H4283 ‐ 49,  and  4H4203 ‐ 72  you  can  view  the  receive  and  transmit  activity  on  the  RX  and  TX  LEDs.  How ever ,  only  one  grou[...]

Using LANVIEW Matrix DFE-Gold Series Modules Hardware Installation Guide 4-3 Viewing Receive/T ransmit Activity on 4H4202-72 On  the  4H4202 ‐ 72,  you  can  view  the  receive  and  transmit  activity  on  the  RX  and  TX  LEDs.  Howeve r ,  only  one  group  of  24  ports [...]

Using LANVIEW 4-4 Troubleshooting Viewing the Receive and T ran smit Activity on 4H4284-49 On  the  4H4284 ‐ 49  DFE ‐ Gold module,  you  can  view  the  receive  and  transmit  activity  on  the  RX  and  TX  LEDs.  How ever ,  only  one  group  of  12  ports  may  b[...]

Using LANVIEW Matrix DFE-Gold Series Modules Hardware Installation Guide 4-5 T able 4-1 LANVIEW LEDs LED Color Stat e Recomme nded Action MGMT None Off . This module is NOT the Management Module. None. Green Solid . This module is the designated Management Module. None. Amber Flashing . This is a temporary indi cation that the module is saving data[...]

Using LANVIEW 4-6 Troubleshooting RX (Receive) None No link . No activity . Port enabled or di sabled. None. Green Solid . Link present, port enabled, no traffic is being received by the i nterface. None. Amber Flashing . Link present, port enabled, traffic is being received by the i nterface. Rate of flashing indicate s the data transmission rate.[...]

Troubleshooting Checklist Matrix DFE-Gold Series Modules Hardware Installation Guide 4-7 T roubleshooting Checklist If  the  module  is  not  work in g  properly ,  refer  to  Ta b l e 4 ‐ 1  for  a  checklist  of  problems,  possible  causes,  and  recommended  actions  to  resolve ?[...]

Troubleshooting Checklist 4-8 Troubleshooting Port(s) goes into standby for no apparent reason. Loop conditio n detected. V erify th at S panning T ree is enabled. Refer to the Enterasys Matrix DFE-Gold Series Confi guration Guide for the instructions to set the type of ST A. Review the network design and dele te unnecessary loops. If the problem c[...]

Overview of DFE-Gold Module Shutdown Procedure Matrix DFE-Gold Series Modules Hardware Installation Guide 4-9 Overview of DFE-Gold Module Shut down Procedure The  DFE ‐ Gold module s  installed  in  a  Mat rix  N3  or  Matrix  N7  chassis  are  inter dependent  and  operate  under  a  single  [...]

Overview of DFE-Gold Module Shutdown Procedure 4-10 Troubleshooting Recommended Shut down Procedure Using OFFLINE/RESET Switch Before  pulling  a  DFE ‐ Gold module  out  of  a  chas sis,  press  or  tap  on  its  OFFLINE/RESET  switch  for  less  than  1 second.  Its  CPU  LED  ch[...]

Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide A-1 A Specifications This  appendix  provides  information  about  the  foll owing: • DFE ‐ Gold  Module  Specifications  (page A ‐ 1) • COM  Po r t  Pinout  Assignments  (page A ‐ 3) • Regulatory  Compliance  (page A ‐ 4)[...]

DFE-Gold Module Specifications A-2 Specifications 4H4203-72 Ports 1 through 72 Seventy- two, 10BASE-T/100BASE-TX compliant ports through six RJ21 connectors. 4H4202-72 Ports 1 through 72 Seventy- two, 10BASE-T/100BASE-TX compliant ports through 72 RJ45 connectors. 4H4284-49 Ports 1 through 48 Forty-eigh t, 100BASE-FX multimode fi ber-optic complian[...]

COM Port Pinout Assignments Enterasys Matrix DFE-Gold Series Modules Hardware Installation Guide A-3 COM Port Pinout Assignment s The  COM  port  is  a  serial  communications  port  for  loc al  access  to  Local  Management.  Refer  to  Ta b l e A ‐ 2  for  the  COM  port  pin  a[...]

Regulatory Compliance A-4 Specifications Regulatory Compliance The  4H4282 ‐ 49,  4H4283 ‐ 49,  4H4203 ‐ 72,  4H4202 ‐ 72,  4H4284 ‐ 49,  and  7G ‐ 6MGBIC  mee t  the  safety  and  electromagnetic  compatibility  (EM C)  requirements  listed  in  Ta b l e A ‐ 3 : T able A-3 Complia[...]

Matrix DFE-Gold Series Modules Hardware Installation Guide B-1 B Mode Switch Bank Settings and Optional Installations This  appendix  covers  the  following  items: • Required  T ools  (page B ‐ 1) • Setting  the  Mode  Switches  (page B ‐ 2) • Memory  Locations  and  Replacement  Procedure s ?[...]

Setting the Mode Switches B-2 Mode Switch Bank Settings and Optional Installations Setting the Mode Switches Figure B ‐ 1  and  Figure B ‐ 2  show  the  location  of  the  mode  switches  and  the  switch  settings  for  normal  operation.  These  switches  are  set  at  the  [...]

Setting the Mode Switches Matrix DFE-Gold Series Modules Hardware Installation Guide B-3 Figure B-1 Mode Switch Location on 4H4282-49 and 4H42 83-49 1 Mode switch bank (located in same location on both the 4H4282-49 and 4H4 283-49) Figure B-2 Mode Switch Location on 4H4203-72 1 Mode switch bank 4H4282-49 F AST ENET DFE 1 2 3 4 5 6 ➀ ON 12 34 5 67[...]

Setting the Mode Switches B-4 Mode Switch Bank Settings and Optional Installations Figure B-3 Mode Switch Location on 4H4202-72 1 Mode switch bank Figure B-4 Mode Switch Location on 4H4284-49 1 Mode switch bank ➀ 1 2345678 ON COM OFFLINE / RESET CPU MGMT GROUP GROUP SELECT GROUP 1 GROUP 2 GROUP 3 1X 6X 7X 12X 13X 18X 19X 24X 1 2 3 4H4202-72 F AST[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Modules Hardware Installation Guide B-5 Memory Locations and Replacement Procedures In  the  event  that  the  Dual  In ‐ line  Memory  Module  (DIMM)  or  DRAM  Single  In ‐ li ne  Memory  Module  (SIMM)  (FLASH  memory) [...]

Memory Locations and Replacement Procedures B-6 Mode Switch Bank Settings and Optional Installations Figure B-6 DIMM and DRAM SIMM Locations (4H4203-72) 1 DRAM SIMM 2 DIMM 3 Main PC board Figure B-7 DIMM and DRAM SIMM Locations (4H4202-72) 1 DRAM SIMM 2 DIMM 3 Main PC board  À Á G R O U P 1 G R O U P 2 G R O U P 3 G R O U P 4 7 2X 7 2X 6 1X 6 1[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Modules Hardware Installation Guide B-7 DIMM Replacement Procedure (4H4282-49 and 4H4283-49) To  remov e  and  replace  the  DRAM  SIMM  on  the  4H4282 ‐ 49  or  4H4283 ‐ 49,  ref er  to  Figure B ‐ 8  and  Figure B ‐ 9  re[...]

Memory Locations and Replacement Procedures B-8 Mode Switch Bank Settings and Optional Installations 2. Refer  to  Figure B ‐ 9 .  Push  the  connector  arms  aw ay  from  the  memor y  module  to  release  it  from  the  connector .  3. Remove  the  module  from  the  connector[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Modules Hardware Installation Guide B-9 Removing the DRAM SIMM from 4H4203-72 To  remov e  the  existing  DRAM  SIMM,  proceed  as  follows: 1. Locate  the  DRAM  SIMM  connector  on  the  main  PC  board.  Refer  back  to [...]

Memory Locations and Replacement Procedures B-10 Mode Switch Bank Settings and Optional Installations 3. Pull  the  DRAM  SIMM  straight  up  and  remove  it  from  the  connector . Installing the DRA M SIMM on 4H4203-72 To  install  the  DRAM  SIMM,  refer  to  Figure B ‐ 12  and  proce[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Modules Hardware Installation Guide B-11 DRAM SIMM Replacement (4H4202-72) Figure B-12 Installing the DRAM SIMM on 4H42 03-72 1 Connector arms 3 Connector fingers 2 DRAM SIMM 4 Alignment notches (2) À Ã Á Ã À Â Note: Because of the complexity of correctly replacing the large d[...]

Memory Locations and Replacement Procedures B-12 Mode Switch Bank Settings and Optional Installations DIMM Replacement Proc edure (All DFE Modules) In  the  event  that  the  DIMM  need s  to  be  replaced,  the  following  sec tions  explain  how  to  remove  and  install  the  DIMM.  [...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Modules Hardware Installation Guide B-13 Inst alling the DIMM To  install  a  DIMM,  refer  to  Figure B ‐ 14  and  proceed  as  follows: 1. Insert  the  DIMM  down  between  the  connector  fingers . 2. Pivot  the  DIMM [...]

Memory Locations and Replacement Procedures B-14 Mode Switch Bank Settings and Optional Installations[...]

Index-1 Index Numerics 100BASE-FX connections 3-18 requirements 2-2 100BASE-TX connections 3-1 1 requirements 2-2 10BASE-T connections 3-1 1 , 3-15 requirements 2-1 4H4202-72 introduction to 1-3 4H4203-72 introduction to 1-3 4H4282-49 introduction to 1-2 4H4283-49 introduction to 1-2 4H4284-49 introduction to 1-3 C Cable connections 4H4282-49 or 4 [...]

Index-2 Matrix N3 chassis module installation into 3-9 Matrix N5 chassis module installation into 3-9 Memory replacement of DRAM B-12 Memory locations DIMM and SIMM B-5 Mode Switch setting of B-2 Module features 1-2 , 1-3 N NEM 3-3 Network connecting to 3-10 Network expansion module 3-3 Network Requirements list of 2-1 O OFFLINE/RESET button 4-10 O[...]