Enterasys Enterasys Gold Distributed Forwarding Engine 4G4282-49 manual

7.5x9-inch cover with bleed on 4 sides Enterasys Matrix ® DFE-Gold Series Hardware Installation Guide Module 4G4282-49 Module 4G4202-72 P/N 9034096-0 2[...]

[...]

i Notice Enterasys Networks  reserv es  the  right  to  make  changes  in  specif ications  and  other  info rmation  contained  in  this  document  and  its  web  site  without  prior  notice.  The  reader  should  in  all  cases  consult  Enterasys Netw orks[...]

ii Regulatory Compliance Information Federal Communications Commission (FCC) Notice This  device  com plies  with  Par t  15  of  th e  FCC  rules.  Operation  is  su bject  to  the  following  two  conditions:  (1)  this  device  may  not  cause  harmfu l  interference, [...]

iii Electromagnetic Compatibility (EMC) This  product  compli es  with  the  following:  47  CFR  Pa r t s  2  and  15,  CSA  C108.8,  2004/10 8/EC,  EN  55022,  EN  61000 ‐ 3 ‐ 2,  EN 61000 ‐ 3 ‐ 3,  EN  55024,  AS/NZS  CISPR  22,  VCCI  V ‐ 3.  Compatibilid[...]

iv Enterasys  Customer  Support  at  353  61  705586  (Ireland). ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼៪ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 &U   ໮⒈㘨㣃 3%% ໮⒈Ѡ㣃䝮 [...]

v VCCI Notice This  is  a  class  A  product  based  on  the  standard  of  the  Vo l u n t a r y  Cont rol  Coun cil  for  Interferen ce  by  Information  Te c h n o l o g y  Equipment  (VCCI).  If  this  equipmen t  is  used  in  a  domes tic  environme nt, [...]

vi Safety Information Class 1 Laser Transceivers The single mode interface modules use Class 1 la ser transceivers. Read the followi ng safe ty information befor e installing or o perating these modules. The  Class  1  laser  transceivers  use  an  optical  feedback  loop  to  maintain  Class  1  operation [...]

vii ENTERASYS NETWORKS, INC. FIRMWARE LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This  document  is  an  agreement  (“ Agreement”)  betwee n  the  end  user  (“Y ou”)  and  Enterasys  Net works,  Inc. ,  on  behalf  of  itse[...]

viii 3. APPLICABLE  LAW. This  Agreem ent  sh all  be  interpreted  and  governed  under  the  laws  and  in  the  state  and  federal  courts  of  th e  Commonwealth  of  Massachusetts  wit hout  regard  to  its  conflicts  of  laws  provisions.  You  a[...]

ix 8. AUDIT  RIGHTS. You  here by  acknowled ge  that  the  intellectu al  property  rights  associated  with  the  Program  are  of  critical  value  to  Enterasys,  and,  accordingly,  You  hereby  agree  to  maintain  complete  books,  re cords  and  accoun[...]

x[...]

ix Contents About This Guide Who Should Use This G uide .............. ............. .......... ............. ............. ............. ............. ......... ... .......... xiii How to Use This G uide ............. ............. ............. ......... ............. ............. ............. ............. ..... ............. xiv Related Docum[...]

x Installing Module into Ma trix N1, N3, or N5 Chassis ............. .......... .......... ............. ............. ...... 3-14 Connecting to the Network . ................ .......... ............. .......... ............. ............. ............ .......... ............. 3-15 Connecting UTP Cables . ............. ............. .......... ....[...]

xi Figures 1-1 4G4202-72 and 4G4282-49 DFE- Gold Modules ........ ............. ............. ......... ............. ............ 1-4 1-2 Optional 7G-6MGBIC and 7G-6 MG BIC-A Ethernet Interface Modules .. ................ ............. .. 1-5 3-1 Removing the Coverplate.... ............. ............. ............. .......... ............. .......[...]

xii Tables 1-1 Optional Ethernet Interface Modules, Compliance, and Physical Connections ................... .. 1-6 3-1 Contents of DFE-Gold Module Carton ............. ....... ............. ............. ......... ............. ............. .. 3-2 4-1 LANVIEW LEDs ............... ............. ............. ............. ......... ............. .[...]

Matrix DFE-Gold Series Installation Guide xiii About This Guide This  guide  provide s  an  overview ,  installation  and  troubleshooting  instructions,  and  specifications  for  the  Enterasys  Matr ix ®  DFE ‐ Gold  (Distributed  Forwarding  Eng ine)  4G4202 ‐ 72  and  4G4282 ?[...]

How to Use This Guide xiv About This Guide How to Use This Guide Read  through  this  guide  completely  to  familiarize  you r se l f  with  its  contents  and  to  gain  an  understanding  of  the  features  and  capabilities  of  the  DFE ‐ Gold  modules.  A  general[...]

Conventions Used in This Guide Matrix DFE-Gold Series Installation Guide xv Conventions Used in This Guide The  following  conventions  are  used  in  this  guide. Lowercase  x:  Indicates  the  general  use  of  an  alphanumeric  character  (for  example,  6x1xx,  the  x’ s  indic[...]

Conventions Used in This Guid e xvi About This Guide[...]

Matrix DFE-Gold Series Installation Guide 1-1 1 Introduction This  chapter  provides  an  overview  of  the  DFE ‐ Gold  module  capabilities,  and  introduces  the  4G4202 ‐ 72  and  4G428 2 ‐ 49  DFE ‐ Gold  mod ules  and  the  optional  uplink  interface  7G ‐ 6MGBIC [...]

Overview of DFE Series Capabilities 1-2 Introduction Overview of DFE Series Cap abilities The  DFE ‐ Gold  Series  modules  provide  you  with  a  larg e  number  of  capabilities,  including: • Support  for  high  speed  Gigabit  Ethernet  traffic  to  desktop  devices •B e t t e[...]

The DFE-Gold Modu les and Interface Options Matrix DFE-Gold Series Installation Guide 1-3 4G4202-72 The  4G4202 ‐ 72  is  an  edge ‐ network  switch  with  72,  10 BASE ‐ T/100BAS E ‐ TX/1000BASE ‐ T  ports  accessed  through  72  front ‐ panel  RJ45  connectors.  4G4282-49 The  4G4282 [...]

The DFE-Gold Modules and Interface Options 1-4 Introduction Figure 1- 1 4G4202-72 and 4 G4282-49 DFE-Gold Modules 1 OFFLINE/RESET switch 6 GROUP status LEDs 2 RJ45 COM (Console Port) 7 GROUP selected LEDs 3 CPU LED 8 4G4202-7 2 - Ports (49-72), 10/100/1000 Mbps, via 24 RJ45s 4 MGMT LED 4G4282-49 - Ethernet Interface Module option slot 5 GROUP SELEC[...]

The DFE-Gold Modu les and Interface Options Matrix DFE-Gold Series Installation Guide 1-5 7G-6MGBIC and 7G-6MG BIC-A Gigabit Ethern et Interface Modules The  4G4282 ‐ 49  option  slot  provides  access  to  an  installed  netw ork  expansion  module  such  as  the  7G ‐ 6MGBIC  and  7G ‐ 6MGB[...]

Connectivity 1-6 Introduction Connectivity 4G4202-72 The  4G4202 ‐ 72  has  10BASE ‐ T/10 0BASE ‐ TX/1000BASE ‐ T  compliant  ports  through  72,  fixed  RJ45  front  panel  connectors. 4G4282-49 Depending  on  how  the  4G4282 ‐ 49  ( Figure 1 ‐ 1 )  is  configured,  it  ca[...]

Standards Compatibility Matrix DFE-Gold Series Installation Guide 1-7 Switch Configuration Using CLI Commands The  CLI  commands  enable  you  to  perform  more  complete  switch  configuration  management  tasks. For  CLI  command  set  information  and  how  to  configure  the  mod[...]

LANVIEW Diagnostic LEDs 1-8 Introduction name  in  a  RADIUS  Filter ‐ ID  attribute.  An  ad ministrator  can  also  define  a  ro le  to  be  implemented  in  the  absence  of  an  authentication  framew ork.  Refer  to  the  release  notes  shipped  with [...]

Matrix DFE-Gold Series Installation Guide 2-1 2 Network Requirements This  chapter  provides  information  concerning  the  network  requirements  that  must  be  me t  to  ensure  a  satisfactory  performance  from  the  DFE  module.  The  information  consists  of  the [...]

10BASE-T Network 2-2 Network Requirements In  normal  usage  (and  typical  implementations)  there  is  no  need  to  enable/disable  ports  for  Link  Aggregation.  The  default  va l u es  will  result  in  the  maximum  number  of  aggregati ons  possible.  If ?[...]

1000BASE-T Network Matrix DFE-Gold Series Installation Guide 2-3 1000BASE-T Network The  4G4202 ‐ 72 and  4G4282 ‐ 49  support  10/100/10 00 Mbps  by  means  of  fixed  RJ45  front  panel  connectors.  These  connections  support  copper  wire  connections  that  can  oper ate  u[...]

1000BASE-T Network 2-4 Network Requirements[...]

Matrix DFE-Gold Series Installation Guide 3-1 3 Installation This  chapter  provides  the  instructions  to  install  the  4G4202 ‐ 72  and  4G4282 ‐ 49  DFE ‐ Gold  modules,  and  an  optional  netw ork  expansion  module. A  Phillips  screwdriver  is  needed  to  instal[...]

Unpacking the DFE-Gold Module 3-2 Installation Unp acking the DFE-Gold Module Unpack  the  DFE ‐ Gold  modul e  as  follows: 1. Open  the  box  and  remov e  the  packing  material  protecting  the  DFE ‐ Gold  module. 2. V erify  the  contents  of  the  carton  as  listed [...]

Installing Optional Network Expansion Modules Matrix DFE-Gold Series Installation Guide 3-3 Removing the Coverplate Refer  to  Figure 3 ‐ 1  and  proceed  as  follows: 1. Attach  the  antistatic  wrist  strap  (refer  to  the  instructions  on  the  antistatic  wrist  strap  package). 2.[...]

Installing Optional Network Expansion Modules 3-4 Installation Figure 3-2 Installing the Network Exp ansion Module 2. Use  the  two  saved  cov erplate  screws  to  fasten  the  network  expansion  module  to  the  DFE ‐ Gold  module  front  panel.  Do  not  tighten  the  two  c[...]

Installing an Optional Mini-GBIC Matrix DFE-Gold Series Installation Guide 3-5 Inst alling an Optional Mini-GBIC This  section  describes  how  to  install  a  Mini ‐ GBIC  in  an  optional  7G ‐ 6MGBIC  or  7G ‐ 6MGBIC ‐ A. To  prepare  and  install  a  Mini ‐ GBIC,  refer  to ?[...]

Installing an Optional Mini-GBIC 3-6 Installation Inst allation To  install  a  Mini ‐ GBIC  with  an  MT ‐ RJ  connection,  ref er  to  Fig ure 3 ‐ 3 .  For  an  LC  connection,  refer  to  Figure 3 ‐ 4 .  For  an  RJ45  connection,  refer  to  Figure 3 ‐ 5 .  The[...]

Installing an Optional Mini-GBIC Matrix DFE-Gold Series Installation Guide 3-7 Figure 3-4 Mini-GBIC with LC Connector Figure 3-5 Mini-GBIC with RJ45 Connector 1 Mini-GBIC (MGBIC-08, -LC01, -LC03, or -LC09) 4 Port slot 2 Mini-GBIC , top side 5 Mini-GBIC , protective dust cover 3 7-Pin edge conne ctor (insertion side) 6 Release tab 1 Mini-GBIC (MGBIC[...]

Removing the Mini-GBIC 3-8 Installation Removing the Mini-GBIC To  remove  a  Mini ‐ GBIC  from  a port  slot,  proceed  as  follows: 1. Attach  the  antistatic  wrist  strap  (refer  to  the  instructions  in  the  antis tatic  wrist  strap  package)  before  removing [...]

Module Placement and Rules Matrix DFE-Gold Series Installation Guide 3-9 Module Placement and Rules The  DFE ‐ Gold  modules  can  be  installed  in  a  Matrix E7,  Matrix N1,  Matrix N3 ,  Matrix N5 ,  or  Matrix N7 chassis.  The  slot  locations  in  the  Ma trix E7,  N3,  N5,  a[...]

Module Placement and Rules 3-10 Installation Example 1 ( Figure 3-6 , A) Shows  one  module  installed  in  the  chassis.  If  the  chassis  is  populated  with  only  one  4xxxxx,  it  must  be  installed  in  slot  1.  Rule:  If  only  one  4xxxxx  is  installe[...]

Installing the DFE Module into a Chassis Matrix DFE-Gold Series Installation Guide 3-11 Inst alling the DFE Module into a Chassis To  install  a  DFE ‐ Gold  module  int o  a  chassis,  proceed  directly  to  “ Preparation ”  on  page 3 ‐ 11  to  start  the  installa tion  process. Prep [...]

Installing the DFE Module into a Chassis 3-12 Installation Inst alling Module into Matrix E7 or N7 Chassis To  install  the  module,  refer  to  Figure 3 ‐ 1  and  proceed  as  follows: 1. Locate  the  chassis  card  guides  tha t  line  up  with  the  slot  number  in  which ?[...]

Installing the DFE Module into a Chassis Matrix DFE-Gold Series Installation Guide 3-13 Figure 3-1 Inst alling Module into M atrix E7 or Mat rix N7 Chassis (E7 shown) 1 Card guides 5 Upper/lower locking tabs (in proper open position) 2 Slot number 1 (Left-most slot is 1.) 6 Upper/lower lockin g tab (in closed positio n) 3 Module card 7 Backplane co[...]

Installing the DFE Module into a Chassis 3-14 Installation Inst alling Module into Matr ix N1, N3, or N5 Chassis A  DFE ‐ Gold  module  can  be  installed  in  any  av ailable  chassis  slot  (1  through  3)  in  the  Matrix N3  chassis  or  slots  1  through  5  in  the  [...]

Connecting to the Network Matrix DFE-Gold Series Installation Guide 3-15 Figure 3-7 Installing Module into N1 , N3, or N5 Chassis (only N3 shown) Connecting to the Network This  section  provides  the  procedures  for  connecting  unshielded  twisted  pair  (UTP)  segments  from  the  network  or  oth[...]

Connecting to the Network 3-16 Installation Connecting UTP Cables The  fixed  RJ4 5  front  panel  connections  of  the  4G4202 ‐ 72  and  4G4282 ‐ 49  are  10/100/1000  Mbps  ports.  These  ports  hav e  internal  crossov ers,  and  also  support  auto matic ‐ polarity  [...]

Connecting to the Network Matrix DFE-Gold Series Installation Guide 3-17 Figure 3 ‐ 10  for  four ‐ wire  RJ45  conne ctions.  Refer  to  Figure 3 ‐ 11  and  Figure 3 ‐ 12  for  eight ‐ wire  RJ45  connections. e. Ensure  that  the  twisted  pai r  connection  meets  the  dB ?[...]

Connecting to the Network 3-18 Installation Figure 3-9 Crossover Four-Wire Cabl e RJ45 Pinout s, Connections Between Network Device s Figure 3-10 Four-Wire Str aight-throu gh Cable RJ45 Pinout s, Connections Between Network Devices 1 RJ45 device port 3 RJ45-to-RJ45 crossover cable 2 Other device port 4 RX+/RX- and TX+/TX- connections. These connect[...]

Connecting to the Network Matrix DFE-Gold Series Installation Guide 3-19 Figure 3-1 1 Eight-Wire Crossover Cable RJ45 Pinout s, Connections Between Network Device s Figure 3-12 Eight-Wire S traight-Through Cable RJ4 5 Pinout s, Connections Between Sw itches and End Syst em Devi ces 1 RJ45 device port 3 RJ45-to-RJ45 crossover cable 2 Other device po[...]

Connecting to the Network 3-20 Installation Connecting Fiber-Opti c Cables to Mini-GBICs This  section  provides  the  procedure  for  connecting  1 ‐ Gigabit  Ethernet  fiber ‐ optic  segments  from  the  network  or  other  devices  to  Mini ‐ GBIC  MT ‐ RJ  or  LC  port ?[...]

Connecting to the Network Matrix DFE-Gold Series Installation Guide 3-21 Figure 3-13 Cable Connection to MT -RJ Fiber- Optic Connectors 1 Installed Mini-GBIC MT -RJ conn ector 4 Receive LED (RX) 2 MT -R J cable connecto r 5 Transmit LED (TX) 3 Release t ab 1 2 3 4 5 6 1 2 3 4 5 6 7G-6MGBIC-A Ä Ã À Á Â[...]

Connecting to the Network 3-22 Installation Figure 3-14 Cable Connection to LC Fiber-Optic Connec tors 3. Plug  the  other  end  of  the  cable  into  the  appropriate  port  on  the  other  devi ce.  Some  cables  may  be  terminated  at  the  other  end  with  two  sepa[...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Installation Guide 3-23 fiber ‐ optic  strand.  In  this  case,  ensure  that  the  transmit  fibe r ‐ optic  strand  is  connected  to  the  receive  port  and  the  receiv e  fiber ‐ optic  strand  to  the [...]

Connecting to COM Port for Local Management 3-24 Installation Wi t h  a  UTP  stra ight ‐ through  cable  and  an  RJ45 ‐ to ‐ DB25  male  adapter ,  yo u  can  connect  products  equipped  with  an  RJ45  COM  port  to  a  Hayes  compatible  modem  that  supports ?[...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Installation Guide 3-25 Figure 3-15 Connecting an IBM PC or Comp atible Device Connecting to a VT Series T erminal To  connect  a  VT  Series  terminal  to  an  Enterasys Networks  DFE ‐ Gold  module  COM  port  ( Figure 3 ‐ 16 ),  use ?[...]

Connecting to COM Port for Local Management 3-26 Installation When  these  parameters  are  se t,  the  Local  Management  password  screen  will  disp lay .  Refer  to  the  Matrix DFE ‐ Gold  Series  Configuration  Guide  for  further  information. Figure 3-16 Connecting a VT Series[...]

Connecting to COM Port for Local Management Matrix DFE-Gold Series Installation Guide 3-27 5. W ith  a  PC  connected  to  a  remote  modem,  you  can  configure  the  switch  remotely .  To  accomplish  this,  you  must  configure  you r  PC  VT  emulation  package  with ?[...]

Connecting to COM Port for Local Management 3-28 Installation Adapter Wiring and Signal Assignment s COM Port Adapter Wiring an d Signal Diagram RJ45 DB9 Pin Conductor Pin Signal 1 Blue 2 Receive (RX) 4 Red 3 T ransmit (TX) 5 Green 5 Ground (GRD) 2 Orange 7 Request to Send (RTS) 6 Y ellow 8 Clear to Send (CTS) VT Series Port Adapter Wi ring and Sig[...]

Completing the Installation Matrix DFE-Gold Series Installation Guide 3-29 Completing the Inst allation Completion  of  th e  DFE  module  installation  depends  upon  the  type  of  system  in  whi ch  the  module  is  being  installed.  •I f  installing  in  a  new  DFE [...]

Completing the Installation 3-30 Installation First-T ime Log-In Using a Console Port Connection Start  the  Command  Line  Interface  (CLI)  from  the  module’ s  local  console  port  as  follo ws: 1. Connect  a  terminal  to  the  local  console  port  as  described  in  ?[...]

Completing the Installation Matrix DFE-Gold Series Installation Guide 3-31 Figure 3-18 Matrix DFE St artup Screen Example (N7 Chassis) Completing the Inst allation of a DFE-Gold Module in an Existing System In  an  established  DFE  module  system , •a  DFE  module  is  already  estab lished  as  the  manage[...]

Completing the Installation 3-32 Installation Logging in with an Administrati vely-Configured User Account If  the  device’ s  default  user  account  settings  have  been  changed,  proceed  as  follows: 1. At  the  login  prompt,  enter  you r  administratively ‐ assigned  user  name[...]

Matrix DFE-Gold Series Installation Guide 4-1 4 T roubleshooting This  chapter  provides  information  concerning  the  following: Unless  otherwise  noted,  the  following  information  applies  to  all  DFE  modules. Using LANVIEW The  modules  use  a  built ‐ in  visual  diagnos[...]

Using LANVIEW 4-2 Troubleshooting Viewing the Receive and T ransmit Activity On  the  4G4202 ‐ 72  and  4G4282 ‐ 49,  yo u  can  view  the  receive  and  transmit  activity  on  the  RX  and  TX  LEDs.  How ever ,  only  one  group  of  ports  may  be  viewed  a[...]

Using LANVIEW Matrix DFE-Gold Series Installation Guide 4-3 Ta b l e 4 ‐ 1  describes  the  LED  indications  and  provides  recommended  actions  as  appropriate. The terms flashing , blinking , and solid used in T able 4-1 indica te the followin g: • Flashing indicates an LED is flashing randomly . • Blinking i[...]

Using LANVIEW 4-4 Troubleshooting Amber and off Alternating (67% on, 33% off) . Indicates that a shutdown process has completed. This indication will remain for 60 seconds before automati cally rest arting. While in this state, you have 60 seconds to safely remove th e DFE-Gold module from the chassis. RX (Receive) None No link . No activity . Port[...]

Troubleshooting Checklist Matrix DFE-Gold Series Installation Guide 4-5 T roubleshooting Checklist If  the  module  is  not  wor ki n g  properly ,  refer  to  Ta b l e 4 ‐ 2  for  a  checklist  of  problems,  possible  causes,  and  recommended  actions  to  resolve  the  probl[...]

DFE-Gold Module Shutdown Procedure 4-6 Troubleshooting DFE-Gold Module Shut down Procedure The  DFE ‐ Gold  modules  installed  in  a  Matrix E7,  Matrix N3,  Ma trix N5,  or  Matrix N7  chassis  are  interdep enden t  and  operate  under  a  single  IP  address  as  a  single, [...]

DFE-Gold Module Shutdown Procedure Matrix DFE-Gold Series Installation Guide 4-7 Yo u  can  shut  down  a  DFE ‐ Gold  module  in  an  operating  system  using  the  OFFLINE/RESET switch  shown  in  Fi gure 4 ‐ 2 .  There  are  tw o  procedures  to  shut  down  a  DFE ?[...]

DFE-Gold Module Shutdown Procedure 4-8 Troubleshooting When  a  controlled  shutdown  is  initiated  from  the  OFFLINE/RESET switch ,  you  have  60  seconds  from  the  time  the  CPU  starts  alternately  flashing  amber/off  until  the  device  automatically  restarts[...]

Matrix DFE-Gold Series Installation Guide A-1 A Specifications This  appendix  provides  information  about  the  f ollowing: Enterasys Network s  res erves  the  right  to  change  the  specifications  at  any  time  without  notice. DFE-Gold Module S pecifications Ta b l e A ‐ 1  provides[...]

Ethernet Interface Module Specifications A-2 Specifications Ethernet Interface Module S pecifications Refer  to  Ta b l e A ‐ 2  for  the  7G ‐ 6MGBIC  and  7G ‐ 6MGBIC ‐ A  specifications.  Processors/Memory Processor MPC750CX, 400 MHz processor Dynamic Random Access Memory (DRAM) 128 MB FLASH Memory 32 MB Physic[...]

Mini-GBIC Input/Output Specifications Matrix DFE-Gold Series Installation Guide A-3 Mini-GBIC Input/Output S pecifications The  Mini ‐ Gigabit  Ethernet  Card  (Mini ‐ GBIC)  port  interface  slots  can  support  1 ‐ Gbps  fiber ‐ optic  and  copper  connections  as  described  in  Ta b [...]

Gigabit Ethernet Specifications A-4 Specifications Gigabit Ethernet S pecifications The  following  specificat ions  for  the  Mini ‐ GBICs  shown  in  Ta b l e A ‐ 4  through  Ta b l e A ‐ 12  meet  or  exceed  the  IEEE  802.3z ‐ 1998  standard. MGBIC-LC01 / MGBIC-MT01 Sp ecifications (10[...]

Gigabit Ethernet Specifications Matrix DFE-Gold Series Installation Guide A-5 MGBIC-LC09 S pecific ations (1000 BASE-LX) MGBIC-08 Sp ecifications (1000BASE-ELX) T able A-7 MGBIC-LC03 Operating Ra nge Item Modal Bandwid th @ 1310 nm Range 62.5 µm MMF 160 MHz/km 2,000 Meters 50 µm MMF 400 MHz/km 2,000 Meters T able A-8 MGBIC-LC09 Optical S pecifica[...]

Gigabit Ethernet Specifications A-6 Specifications MGBIC-02 Sp ecifications (1000BASE-T) Link Power Budget 1 (Full Duplex Only) 23 dB 28 dB, typical 1. The maximum dr ive distance (up to 70 km) depends on the quality of the installed single-mode fiber- optic cable segment . Use the Link Power Budget to calcula te the maximum cable length of the att[...]

COM Port Pinout Assignments Matrix DFE-Gold Series Installation Guide A-7 COM Port Pinout Assignment s The  COM  port  is  a  serial  communications  port  for  access  to  Local  Management.  Refer  to  Ta b l e A ‐ 13  for  the  COM  port  pin  assignments. Regulatory Compliance The[...]

Regulatory Compliance A-8 Specifications[...]

Matrix DFE-Gold Series Installation Guide B-1 B Mode Switch Bank Settings and Optional Installations This  appendix  covers  the  following  items: Required T ools Use  the  following  tools  to  perform  the  procedures  provided  in  this  appendix: •A n t i s t a t i c  wrist  strap • Phi[...]

Setting the Mode Switches B-2 Mode Switch Bank Settings and Optional Installations Figure B ‐ 1  through  Figure B ‐ 3  show  the  location  of  the  mode  switches  and  the  switch  settings  for  normal  operation.  These  switches  are  set  at  the  factory  to  th [...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Installation Guide B-3 Memory Locations and Replacement Procedures In  the  event  that  the  Dual  In ‐ Line  Memory  Module  (DIMM)  or  DRAM  Single  In ‐ line  Memory  Module  (SIMM)  (FLASH  memory)  needs  to  [...]

Memory Locations and Replacement Procedures B-4 Mode Switch Bank Settings and Optional Installations Figure B-3 Memory Module Locations on the 4G4282-49 DRAM SIMM Replacement Procedure Removing the DRAM SIMM To  remove  the  DRAM  SI MM,  proceed  as  follows: 1. If  an  netw ork  expansion  module  is  instal[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Installation Guide B-5 Figure B-4 NEM Removal and DRAM SIMM Connector Location on 4G4282-49 2. Refer  to  Figure B ‐ 5 .  Push  the  connector  arms  aw ay  from  the  DRAM  SIMM  and  simultaneous ly  lift  the  DRAM  SIMM  en[...]

Memory Locations and Replacement Procedures B-6 Mode Switch Bank Settings and Optional Installations Inst alling the DRA M SIMM on 4G4282-49 To  install  a  DRAM  SIMM,  refer  to  Figure B ‐ 6  and  proceed  as  follows: 1. Insert  the  DRAM  SIMM  down  between  the  connector  fingers. 2[...]

Memory Locations and Replacement Procedures Matrix DFE-Gold Series Installation Guide B-7 DIMM Replacement Procedure The  DIMM  is  considered  a  fi eld  replaceable  unit  on  both  the  4G4202 ‐ 72  and  4G4282 ‐ 49. Removing the DIMM To  remove  the  existing  DIMM,  proceed  as  f[...]

Memory Locations and Replacement Procedures B-8 Mode Switch Bank Settings and Optional Installations Inst alling the DIMM on 4G4202-72 or 4G4282-49 To  install  a  DIMM,  refer  to  Figure B ‐ 8  and  proceed  as  follows: 1. Push  the  connector  arms  aw ay  from  the  DIMM  enough  to ?[...]

Index-1 Index Numerics 1000BASE-SX/LX/ELX network connections requirements for 2-2 1000BASE-T network connections requirements for 2-3 100BASE-TX requirements 2-2 10BASE-T connection 3-16 requirements 2-2 4G4202-72 connectivity 1-6 introduction to 1-3 4G4282-49 connectivity 1-6 introduction to 1-3 C Cable Fiber budget A-3 Cable connections 4G4202-7[...]

Index-2 Matrix N1 chassis module installation into 3-14 Matrix N3 chassis module installation into 3-12 , 3- 14 Matrix N5 chassis module installation into 3-12 , 3- 14 Matrix N7 chassis module installation into 3-1 1 Memory locations DIMM and SIMM B-3 MGBIC-02 specifications for A-6 MGBIC-08 specifications for A-5 MGBIC-LC01 specifications for A-4 [...]