Fujitsu KD96009-0648 manual

LINE THERMAL PRINTER MODEL KD02906-12XX Series User’ s Manual KD96009-0648 FUJITSU LIMITED[...]

WEEE MARK ,I RX ZDQWWR GLVSRVH WKLV SURGXFW GR QRW PL[ ZLWK JHQHUDO KRXVHKROG ZDVWH7KHUH LV D VHSDUDWHFROOHFWLRQVVWHPV IRUXVHGHOHFWURQLFV SURGXFWVLQDF FRUGDQFH ZLWKOHJLVODWLRQXQGHU WKH:((('LUHFWLYH'LUHFWLYH(&[...]

IMPORT ANT : This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are de[...]

— 1 — GENERAL PRECAUTIONS ● Before using this product, be sure to read through this manual. After having read this manual, keep it in a safe, readily accessible place for future reference. ● The information contained herein is subject to change without prior notice. ● Reproduction or transfer of part or all of this document in any means i[...]

— 2 — SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTL Y OBSERVED Before using this product for the first time, carefully read these SAFETY PRECAUTIONS. Improper handling may result in accidents (fire, electric shock or injury). In order to prevent injury to operators, third parties, or damage to property , special warning symbols are used in the[...]

— 3 — ■ Do not use or store this product in a place where it will be exposed to: * Flames or moist air . * Direct sunlight. * Hot airflow or radiation from a heating device. * Salty air or corrosive gases. * Ill-ventilated atmosphere. * Chemical reactions in a laboratory . * Airborne oil, steel particles, or dust. * Static electricity or stro[...]

— 4 — Do not use the printer under the following conditions. ■ A state subject to vibration or unstable state. ■ A state with this product slanted. • Otherwise dropping may cause injury . • Poor print quality may occur . ■ A state where the printer ventilation holes are obstructed by a nearby wall or other equipment. ■ A state where[...]

— 5 — PRECAUTIONS IN HANDLING THE PRINTER Please observe the following precautions for Powered USB cable.: ■ Do not plug or unplug the Powered USB cable with a wet hand. ■ Use the Powered USB cable only at the specified POS unit. ■ Do not use a deformed or damaged the Powered USB cable. ■ Do not move the printer while the printer power [...]

— 6 — Caution label is attached on the position shown in the following figure. Carefully r ead the precautions in handling before using the printer . THIS LABEL INDICA TES THE RISK OF ANY INJURY DUE TO “HIGH TEMPERA TURE” OF THE PRINT HEAD. To prevent possible malfunction or failure observe the following. ■ A void operating the printer wi[...]

— 7 — Observe the following precautions for daily maintenance. ■ When cleaning the printer , pull out the Powered USB cable. ■ Use a soft, dry cloth for cleaning the surface of the printer case. ■ For severe stains, use a soft cloth slightly dampened with water . ■ Never use organic cleaning solvent such as alcohol, paint thinner , tric[...]

— 8 — THE T ABLE OF CONTENTS 1. GENERAL OUTLINE ................................................................... 9 1.1 Features .......................................................................................... 9 1.2 Unpacking ..................................................................................... 10 1.3 Model Classific[...]

— 9 — 1. GENERAL OUTLINE This product is a thermal line printer designed for use with a POS terminal. With extensive features, they can be used in a wide range of applications. 1.1 Features ● Drop-in Paper Roll mechanism facilitating easy paper handling and head cleaning. ● High speed (220 mm/s) printing. ● V ersatile roll capacity with a[...]

— 10 — 1.2 Unpacking When unpacking the printer , confirm that the following are provided: ● Printer: 1 ● Sample paper roll: 1 roll ● User’ s manual (This manual): 1 Printer Sample paper roll User’ s manual (This manual) 1.3 Model Classification The position of partition and color of case differ depending on the model used. • KD0290[...]

— 11 — 1.4 Basic Specifications Item Specifications Model KD02906-1200 , KD02906-1201, KD02906-1202, KD02906-1203 Print method Line thermal dot print method Print width *1 72 mm/576 dots, 48 mm/384 dots Dot density 8 × 8 dots/mm (203 dpi) Print speed 220 mm/s (Fastest, print density 130 %), 1760 dot lines/s Number of print columns *2 Character[...]

— 12 — 2. EXPLANA TION OF PRINTER P ARTS 2.1 Printer Appearance Printer cover Operation panel Cover open lever Rear connector (Front view) (Rear view) ● Printer cover Paper is loaded under this cover . ● Cover open lever To refill or replace paper , open the printer cover by lifting the cover open lever .[...]

— 13 — ● POWER LED Illuminated when the printer power is on and off when the printer power is off. May blink or light in a special mode or in case of failure. ● ERROR LED Illuminated or blinks when paper is empty or in case of failure. The interval length of blinking represents the type of error . ● FEED button Pressing this button once c[...]

— 14 — 2.2 Printer Cover Inside ● Paper -end sensor Stops printing when this sensor detects paper end. 2.3 Other Built-in Functions ● Buzzer This printer has a built-in buzzer . It is operated in case of cutter error with memory switch SW5-1 set to be valid. ● User memory Allows downloading of user -defined characters and logo data in the[...]

— 15 — CAUTION! ■ When disconnecting the cable, always hold the connector . ■ A void locating the interface cable in places which may cause tripping or falling. 3. PREP ARA TION 3.1 Connecting Interface Cables Confirm that the power switch of the POS terminal is OFF and connect the interface cable. Orient the interface cable connector corre[...]

— 16 — CAUTION! DO NOT connect any other device than the specified cash drawer to the cash drawer kick-out connector . (DO NOT connect a telephone line either .) 3.2 Connecting the Cash Drawer Cash drawer kick-out connector Cash drawer cable connector 1. Confirm that the power switch of the POS terminal is OFF . 2. Confirm the top and bottom of[...]

— 17 — 3.3 Partition for Paper Roll At the time of shipment, this partition is set to 80-mm wide (with one partition) or 58-mm wide (with two partitions) depending on the model. Do not remove the partition. Partition 80mm type 58mm type[...]

— 18 — 4 3 2 1 3.4 Adjusting the Paper Near -end Sensor At the time of shipment, the sensor is set to “1”. 1. Lightly push in the paper near -end sensor unit. 2. Move the paper near -end sensor unit to the right and left while keeping to press it. The sensor position is as shown below depending on the diameter of the roll paper used. Sensor[...]

— 19 — 4. MAINTENANCE AND TROUBLESHOOTING 4.1 Setting/Replacing the paper roll CAUTION! ■ Always use the specified types of paper roll. ■ Confirm that the paper roll is set correctly . ■ When the paper is skewed and not extended straightforward from under the printer cover , open the printer cover and adjust the paper correctly . ■ When[...]

— 20 — 4.3 Cleaning the Print Head 1. T urn the POS terminal power off. 2. Open the printer cover . 3. W ait several minutes. Wipe off any debris on the heating element of the head using a cotton swab soaked in ethyl alcohol. CAUTION! The print head is hot immediately after printing. DO NOT touch it with your hand. DO NOT touch the heating elem[...]

— 21 — 4.5 Hexadecimal Dump Printing This function is to print all received data in hexadecimal numbers. If problems such as missing data, data duplication, etc. should occur , this function allows checking whether or not the printer is receiving data correctly . Set paper to the printer and keep the printer cover open. With the FEED button pre[...]

— 22 — Lighting and blinking status of each error including the above is shown below . Status POWER LED ERROR LED Buzzer Paper -end Lights Lights Paper near-end Lights Lights Cover open Lights Lights Cover open error *1 Lights Cutter lock error Lights Head overheat error Lights Motor overheat error Lights Memory check error Lights Low voltage e[...]

— 23 — 44 55 d D 75 Maximum print area 72 φ 102 or less Printing surface (Unit: mm) 5.2 Printing Paper Use the print paper shown in the following table or the paper with equivalent quality . Paper T ype Product Name Recommended thermal PD160R, PD190R from Ohji Paper paper roll HP220AB-1, PB670, PB770 from Mitsubishi Paper Paper width 80 +0 −[...]

— 24 — 5.3 Manual Setting of Memory Switch Memory switches can be set manually or by a command. For manual setting, refer to the next page. The function of each memory switch is shown in the following table. (The white-on-black characters are factory setting.) Switch No. Setting 0 (OFF) 1 (ON) Memory SW1-1 Power ON Info V alid Not send SW1-2 Bu[...]

— 25 — Switch No. Setting Default Set V alues Memory SW7-1 Baud Rate 9600 bps 1200 bps, 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps SW7-2 Data Length 8bits 7bits, 8bits SW7-3 Stop Bit 1bit 1bit, 2bits SW7-4 Parity NONE NONE, EVEN, ODD SW7-5 Flow Control XON/XOFF DTR/DSR, XON/XOFF SW7-6 DMA Control V alid V alid, In[...]

— 26 — 2. Selecting memory switch When the FEED button is pressed short (within 2 seconds), printing occurs in the order of “Memory SW1” → “Memory SW2” → “Memory SW3” → ......“Memory SW10” → “Save T o Memory” → “Memory SW1” → ...... repeatedly . When the memory switch you want to change is reached, press and [...]

T A74906-00F 1.00E-0604 Printed in Japan[...]