Gigabyte AMD Socket 939 Processor Motherboard GA-K8NMF-9 manual

GA-K8NMF-9 AMD Socket 939 Processor Motherboard User's Manual Rev. 1003 12ME-K8NMF9-1003 * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!! * The WEEE mar[...]

May. 6, 2005 Motherboard GA-K8NMF-9 Motherboard GA-K8NMF-9 May. 6, 2005[...]

Copyright © 2005 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any mean[...]

- 4 - T able of Contents GA-K8NMF-9 Motherboard Layout ................................................................................ 6 Block Diagram ................................................................................................................ 7 Chapter 1 Hardware Installation ...................................................[...]

- 5 - Chapter 3 Drivers Installation ...................................................................................... 47 3 - 1 Install Chipset Drivers .................................................................................... 4 7 3 - 2 Software Application .............................................................................[...]

- 6 - GA-K8NMF-9 Motherboard Layout A TX_12V CPU_F AN CODEC IT8712 nVIDIA ® nForce TM 4(-4X) BIOS PCIE_1 DDR1 F_USB2 F_USB1 DDR2 DDR3 BAT AT X IDE2 FDD CLR_CMOS SYS_F AN GA-K8NMF-9 KB_MS Socket 939 USB LAN F_AUDIO CD_IN F_P ANEL DDR4 IDE1 PCI1 PCI2 SUR_CEN PCIE_16 COMA LPT AUDIO TSB43AB23 RTL8201 F1_1394 S_A T A1 USB 1394 COMB S_A T A3 S_A T A0 S_[...]

- 7 - Block Diagram AMD K8 Socket 939 CPU CPUCLK+/-(200MHz) Hyper T ransport Bus nVIDIA ® nForce4(-4X) DDR 400/333/266/200MHz DIMM 24MHz 33MHz IT8712 4 Serial A T A A T A33/66/100/133 IDE Channels PCICLK (33MHz) 2PCI PCI Bus 8 USB Ports Dual Channel Memory Floppy PS/2 KB/Mouse LPT Port PCI-ECLK (100MHz) LPC BUS 2 IEEE1394 TSB43AB23 1 PCI Express x[...]

- 8 -[...]

Hardware Installation - 9 - English 1-1 Considerations Prior to Installation Preparing Y our Computer The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below: 1. Please turn off the computer [...]

GA-K8NMF-9 Motherboard - 1 0 - English CPU  Socket 939 for AMD Athlon TM 64 / 64FX processor (K8)  1600MHz system bus  Supports core frequencies in excess of 3000+ and faster Chipset  nVIDIA ® nForce4(-4X) Chipset  Supported on the Win 2000/XP operating systems Memory  4 DDR DIMM memory slots (supports up to 4GB memory) (Note 1) [...]

Hardware Installation - 11 - English I/O Control  IT8712F Hardware Monitor  System voltage detection  CPU temperature detection  CPU / System fan speed detection  CPU warning temperature  CPU fan failure warning  CPU smart fan control Onboard SA T A RAID  Onboard nForce4(-4X) chipset (S_A T A0, S_A T A1, S_A T A2, S_A T A3) [...]

GA-K8NMF-9 Motherboard - 1 2 - English 1 - 3 Installation of the CPU and Fan Heat Sink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert pr[...]

Hardware Installation - 13 - English 1-3-2 Installation of the Fan Heat Sink The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. T o prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heat sink. Fig.1 B[...]

GA-K8NMF-9 Motherboard - 1 4 - English Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure tha[...]

Hardware Installation - 15 - English Dual Channel Memory Configuration The GA-K8NMF-9 supports the Dual Channel T echnology . When the Dual Channel T echnology is activated, the bandwidth of memory bus will be double the original one. Due to CPU limitation, if you want to operate the Dual Channel T echnology , please follow the guidelines below for[...]

GA-K8NMF-9 Motherboard - 1 6 - English 1 - 5 Installation of Expansion Cards Y ou can install your expansion card by following the steps outlined below: 1. Read the related expansion card's instruction document before install the expansion card into the computer. 2. Remove your computer's chassis cover, screws and slot bracket from the co[...]

Hardware Installation - 17 - English 1 - 6 I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector T o install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple). IEEE1394 Port Connects the IEEE1394 devices to this connector. USB port Before you connect your device(s) into[...]

GA-K8NMF-9 Motherboard - 1 8 - English 1-7 Connectors Introduction 1) A TX_12V 2) A TX (Power Connector) 3 ) CPU_FAN 4 ) SYS_FAN 5 ) FDD 6) IDE1 / IDE2 7) S_A T A0 / S_A T A1 / S_A T A2 / S_A T A3 8) B A T 9 ) F_P ANEL 1 0 ) F_AUDIO 1 1 ) CD_IN 1 2 ) SUR_CEN 1 3 ) SPDIF_IO 1 4) F_USB1 / F_USB2 15 ) F1_1394 16) C I 1 7 ) CLR_CMOS 13 6 5 7 10 11 2 9 [...]

Hardware Installation - 19 - English 1/2) A TX_12V/A TX (Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its pr[...]

GA-K8NMF-9 Motherboard - 2 0 - English 3/4) CPU_F AN / SYS_F AN (Cooler Fan Power Connector) The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connectio[...]

Hardware Installation - 21 - English 6 ) IDE1 / IDE2 (IDE Connector) An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device [...]

GA-K8NMF-9 Motherboard - 2 2 - English 8 ) BA T (BA TTERY) 9 ) F_P ANEL (Front Panel Jumper) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_P ANEL connector according to the pin assignment below . MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) PW (Power [...]

Hardware Installation - 23 - English 1 1 ) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD-R 1 1 0 ) F_AUDIO (Front Audio Panel Connector) If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must [...]

GA-K8NMF-9 Motherboard - 2 4 - English 1 2 ) SUR_CEN (Surround Center Connector) Please contact your nearest dealer for optional SUR_CEN cable. Pin No. Definition 1 SUR OUTL 2 SUR OUTR 3 GND 4 No Pin 5 CENTER_OUT 6 BASS_OUT 7 AUX_L 8 AUX_R 7 1 8 2 1 3 ) SPDIF_IO (SPDIF In / Out Connector) The SPDIF output is capable of providing digital audio to ex[...]

Hardware Installation - 25 - English 1 4 ) F_ USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable,[...]

GA-K8NMF-9 Motherboard - 2 6 - English 1 7 ) CLR_CMOS (Clear CMOS) Y ou may clear the CMOS data to its default values by this jumper . T o clear CMOS, temporarily short 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper. 1 6 ) CI (Chassis Intrusion, Case Open) This 2-pin connector allows your syst[...]

Hardware Installation - 27 - English[...]

GA-K8NMF-9 Motherboard - 2 8 - English[...]

BIOS Setup - 29 - English BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to[...]

GA-K8NMF-9 Motherboard - 3 0 - English The Main Menu (For example: BIOS V e r . : F8) Once you enter Award BIOS CMOS Setup Utility , the Main Menu (as figure below) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. CMOS Setup Utility-Copyright (C) 1984-2005 A ward Software `[...]

BIOS Setup - 31 - English      Standard CMOS Features This setup page includes all the items in standard compatible BIOS.      Advanced BIOS Features This setup page includes all the items of Award special enhanced features.      Integrated Peripherals This setup page includes all onboard peripherals. ?[...]

GA-K8NMF-9 Motherboard - 3 2 - English 2-1 Standard CMOS Features Date The date format is <week>, <month>, <day>, <year>. Week The week, from Sun. to Sat., determined by the BIOS and is display only. Month The month, Jan. Through Dec. Day The day, from 1 to 31 (or the maximum allowed in the month) Y ear The year, from 1999 t[...]

BIOS Setup - 33 - English IDE Channel 2/3/4/5 Master IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection. Extended IDE Drive SA T A devices setup. Y ou can use one of two methods: Auto Allows BIOS to automatically detect SA T A IDE devices during POST . (Default value) None Select this if no SA T A ID[...]

GA-K8NMF-9 Motherboard - 3 4 - English 2-2 Advanced BIOS Features Hard Disk Boot Priority Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc. Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu. First / Second / Third Boot Device [...]

BIOS Setup - 35 - English Init Display First This feature allows you to select the first initiation of the monitor display from which card when you install a PCI card and a PCI Express VGA card on the motherboard. PEG Set Init display first to PCI Express VGA card. (Default value) PCI slot Set Init display first to PCI. 2 - 3 Integrated Peripherals[...]

GA-K8NMF-9 Motherboard - 3 6 - English On-Chip IDE Channel0 Enabled Enable onboard 1st channel IDE port. (Default value) Disabled Disable onboard 1st channel IDE port. On-Chip IDE Channel1 Enabled Enable onboard 2nd channel IDE port. (Default value) Disabled Disable onboard 2nd channel IDE port. IDE DMA transfer access Enabled Enable IDE DMA transf[...]

BIOS Setup - 37 - English NV SA T A 1 Primary RAID Enabled Enable 1st SA T A primary RAID function. (Default value) Disabled Disable this function. (Default value) NV SA T A 1 Secondary RAID Enabled Enable 1st SA T A secondary RAID function.(Default value) Disabled Disable this function. NV Serial-A T A 2 Enabled Enable Serial A T A 2 supported. (D[...]

GA-K8NMF-9 Motherboard - 3 8 - English Onboard Parallel Port Disabled Disable onboard LPT port. 378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value) 278/IRQ5 Enable onboard LPT port and address is 278/IRQ5. 3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7. Parallel Port Mode SPP Using Parallel port as Standard Parallel [...]

BIOS Setup - 39 - English 2-4 Power Management Setup ACPI Suspend T ype S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value) S3(STR) Set ACPI suspend type to S3/STR(Suspend T o RAM). Soft-Off by Power button Instant-off Press power button then Power of f instantly . (Default value) Delay 4 Sec Press power button 4 seconds to P[...]

GA-K8NMF-9 Motherboard - 4 0 - English Power On by Mouse Disabled Disabled this function. (Default value) Double Click Double click on PS/2 mouse left button to power on the system. Power On by Keyboard Disabled Disabled this function. (Default value) Any KEY Press any key to power on the system. Keyboard 98 If your keyboard have "POWER Key&qu[...]

BIOS Setup - 41 - English 2 - 6 PC Health Status Reset Case Open Status Disabled Don't reset case open status. (Default value) Enabled Clear case open status at next boot. Case Opened If the case is closed, "Case Opened" will show "No". If the case has been opened, "Case Opened" will show "Y es". If you [...]

GA-K8NMF-9 Motherboard - 4 2 - English Current CPU T emperature Detect CPU temperature automatically. Current CPU/SYSTEM F AN Speed (RPM) Detect CPU/SYSTEM fan speed status automatically. CPU Warning T emperature 60 o C / 140 o F Monitor CPU temperature at 60 o C / 140 o F. 70 o C / 158 o F Monitor CPU temperature at 70 o C / 158 o F. 80 o C / 176 [...]

BIOS Setup - 43 - English T emp Limit of Low Speed (Default temperature: 20 o C) The CPU fan will stop spinning when the CPU temperature is below the value set in Temp of FAN turn off option. The CPU fan will start to spin again with the parameter set in CPU FAN: Low Speed when the CPU temperature exceeds the value set in Temp Limit of Low Speed. T[...]

GA-K8NMF-9 Motherboard - 4 4 - English 2 - 8 Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. 2 - 9 Set Supervisor/User Password When you select this function, the following message will appear at the center of the screen to assist you in creating a passwor[...]

BIOS Setup - 45 - English 2-10 Save & Exit Setup T ype "Y" will quit the Setup Utility and save the user setup value to R TC CMOS. T ype "N" will return to Setup Utility . 2 - 1 1 Exit Without Saving T ype "Y" will quit the Setup Utility without saving to RTC CMOS. T ype "N" will return to Setup Utility .[...]

GA-K8NMF-9 Motherboard - 4 6 - English[...]

Drivers Installation - 47 - English Pictures below are shown in Windows XP. Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the Setup.exe. Chapter 3 Driver[...]

GA-K8NMF-9 Motherboard - 48 - English 3-2 Software Application This page displays all the tools that GIGABYTE developed and some free software. Y ou can click an item to install it. 3-3 Software Information This page lists the contents of software and drivers in this CD-title.[...]

Drivers Installation - 49 - English 3-4 Hardware Information This page lists all device you have for this motherboard. 3-5 Contact Us Please see the last page for details.[...]

GA-K8NMF-9 Motherboard - 50 - English[...]

Appendix - 51 - English Chapter 4 Appendix 4-1 Unique Software Utilities 4-1-1 EasyT une 5 Introduction EasyT une 5 presents the most convenient Windows based system performance enhancement and manageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancing system performance, 2) C.I.A. and M.I.B. for s[...]

GA-K8NMF-9 Motherboard - 52 - English 4-1-2 Xpress Recovery Introduction What is Xpress Recovery ? Xpress Recovery is a utility used to back up and restore an OS partition. If the hard drive is not working properly, the user can restore the drive to its original state. 1. Supports FA T16, F A T32, and NTFS formats 2. Must be connected to the IDE1 M[...]

Appendix - 53 - English 2. Press F9 during powering on the computer . (T ext Mode) Press F9 during powering on the computer . Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE T echnology CO. , Ltd. 1. Execute Backup Utility 2. Execute Restore Utility 3. Remove Backup Image 4. Set Password 5. Exit and Restart 1. If you have already entered Xpress [...]

GA-K8NMF-9 Motherboard - 54 - English 1. Execute Backup Utility:      Press B to Backup your System or Esc to Exit The backup utility will automatically scan your system and back up data as a backup image in your hard drive. Not all systems support access to Xpress Recovery by pressing the F9 key during computer power on. If this is [...]

Appendix - 55 - English Method 1 : Q-Flash TM Utility Q-Flash TM is a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-Flash TM allows users to flash BIOS without any utility in DOS or Windows. Using Q-Flash TM indicating no more fooling around with any complicate[...]

GA-K8NMF-9 Motherboard - 56 - English Entering the Q-Flash TM utility: CMOS Setup Utility-Copyright (C) 1984-2004 A ward Software  Sta ndard CMOS Features  Adva nced BIOS Features  Integrated Peripherals  Power M a nage ment Setup  PnP/PCI Configurations  PC Health Status  MB Intelligent T weaker(M.I.T .) Select La nguage Loa d[...]

Appendix - 57 - English Dual BIOS Utility Boot From...................................... M ain Bios Main ROM T ype/Size...................... SST 49LF004A 512K Backup ROM T ype/Size.................. SST 49LF004A 512K W ide Ra nge Protection Disa ble Boot From M ain Bios Auto Recovery Ena ble Halt On Error Disa ble Copy Main ROM Data to Ba ckup Lo[...]

GA-K8NMF-9 Motherboard - 58 - English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed. Dual BIOS Utility Boot From...................................... M ain Bios Main ROM T ype/Size...................... SST 49LF004A 512K Backup ROM T ype/Size[...]

Appendix - 59 - English CMOS Setup Utility-Copyright (C) 1984-2004 A ward Software  Sta ndard CMOS Features  Adva nced BIOS Features  Integrated Peripherals  Power M a nage ment Setup  PnP/PCI Configurations  PC Health Status  MB Intelligent T weaker(M.I.T .) ESC: Quit F3: Cha nge La nguage F8: Dual BIOS/Q-Fla sh F10: Save &[...]

GA-K8NMF-9 Motherboard - 60 - English Exploring the Q-Flash TM utility screen The Q-FlashBIOS utility screen consists of the following key components. T ask menu for Q-Flash utility: Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable execution of the task. Action bar: Contains the names of four acti[...]

Appendix - 61 - English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time. Q-Flash Utility V1.30 Flash T ype/Size.................................SST 49LF003A 256K Keep DMI Data Ena b le Update BIOS from Floppy Save BIOS to Floppy Ent[...]

GA-K8NMF-9 Motherboard - 62 - English Method 2 : @BIOS TM Utility If you do not have a DOS startup disk, we recommend that you use the new @BIOS utility. @BIOS allows users to update their BIOS under Windows. Just select the desired @BIOS server to download the latest version of BIOS. 1. Methods and steps: I. Update BIOS through Internet: a. Click [...]

Appendix - 63 - English III. Save BIOS: In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. IV. Check out supported motherboard and Flash ROM: In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out which kind of[...]

GA-K8NMF-9 Motherboard - 64 - English 4-1-4 Serial A T A BIOS Setting Utility Introduction RAID Levels RAID (Redundant Array of Independent Disks) is a method of combining two hard disk drives into one logical unit. The advantage of an Array is to provide better performance or data fault tolerance. Fault tolerance is achieved through data redundant[...]

Appendix - 65 - English Please follow the steps below to construct a complete RAID array: 1) Have ready your hard drives for RAID construction. Note: T o achieve best performance, it is recommended that the hard drives used are of similar make and storage capacity. 2) Please attach the hard drive connectors to their appropriate location on the moth[...]

GA-K8NMF-9 Motherboard - 66 - English Using the "Define a New Array" Window If necessary, press the tab key to move from field to field until the appropriate field is highlighted. Selecting the RAID Mode By default, this is set to Mirroring. T o change to a different RAID mode, press the down arrow key until the mode that you want appears[...]

Appendix - 67 - English Completing the RAID BIOS Setup After assigning your RAID array disks, press F7. The Clear disk data prompt appears. N VIDIA RAID Utility Jan 12 2005 - Define a New Array - RAID Mode: Mirr oring Stri ping Block: Optimal Free Disks Loc Disk Model Na me Array Disks Loc Disk Model Na me [      ] Add [    [...]

GA-K8NMF-9 Motherboard - 68 - English Press Enter to view and verify details. The Array Detail screen appears. The Array Detail screen shows various information about the array that you selected, such as Striping Block used, RAID Mode, Striping Width, Disk Model Name, and disk capacity. Array 2 : N VIDIA MIRROR 1 1 1.79G - Array Detail - RAID Mode:[...]

Appendix - 69 - English Installing the RAID drivers T o install W indows 2000/XP onto a Serial A T A hard disk sucessfully , you need to install required driver for the SA T A controller on your motherboard during OS installation. Without the driver , the hard disk may not be recognized during the Windows setup process. First of all, you have to co[...]

GA-K8NMF-9 Motherboard - 70 - English 4-1-5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and Settings: We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output is applied. STEP 1: Connect the stereo speakers or earphone to "Line Out". STEP 2: Following i[...]

Appendix - 71 - English STEP 2: Following installation of the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function. STEP 3: Click "Speaker Configuration" and select the "UAJ Function". Then click on the left selection bar and select "4CH Speaker" to c[...]

GA-K8NMF-9 Motherboard - 72 - English STEP 2: Following installation of the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function. STEP 3: Click "Speaker Configuration" and select the "UAJ Function". Then click on the left selection bar and select "6CH Spea[...]

Appendix - 73 - English 8 Channel Audio Setup (requires Audio Combo Kit, optional device) : Audio Combo Kit includes a Surround-Kit and a SPDIF output cable (an optical and coaxial cable). If you want to set up an 8 channel configuration, you need to use the Surround-Kit. The Surround-Kit offers R/L surround, center/subwoofer output and rear surrou[...]

GA-K8NMF-9 Motherboard - 74 - English Method 2: Connect the front channels to the "Line Out" port located on the audio panel and the rear channels to the "Line In" port. Connect the center/subwoofer channels to the "MIC In" port located on the audio panel and the R/L channels to the Surround-Kit "SUR BACK" po[...]

Appendix - 75 - English SPDIF Output Device (Optional Device) A "SPDIF output" connector is available on the motherboard. Cable with rear bracket could link to the "SPDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting port (Note) . 1. Connect the SPDIF[...]

GA-K8NMF-9 Motherboard - 76 - English Jack-Sensing and UAJ Introduction Jack-Sensing provides audio connectors error-detection function. Install Microsoft DirectX8.1 or later version before to enable Jack-Sensing support for Windows 98/ 98SE/ 2000/ ME. Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels (Following[...]

Appendix - 77 - English If you set wrong with the connectors, the warning message will come out as right picture. Manual setting: If the device picture shows different from what you set, please press "Manual Selection" to set. UAJ Introduction UAJ (Universal Audio Jack) has a very smart feature: It will switch signal automatically when us[...]

GA-K8NMF-9 Motherboard - 78 - English 4-2 T roubleshooting Below is a collection of general asked questions. T o check general asked questions based on a specific motherboard model, please log on to http://www.gigabyte.com.tw Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why? Answer: Some advanced op[...]

Appendix - 79 - English Contact Us      T aiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., L TD . Address: No.6, Bau Chiang Road, Hsin-Tien, T aipei 231, T aiwan TEL: +886-2-8912-4888 FAX: +886-2-8912-4003 T ech. Support : http://tw .giga-byte.com/T echSupport/ServiceCenter .htm Non-T ech. Support(Sales/Marketing) : http://ggts.gigabyt[...]

GA-K8NMF-9 Motherboard - 80 - English      China NINGBO G.B.T . TECH. TRADING CO., L TD. T ech. Support : http://tw .giga-byte.com/T echSupport/ServiceCenter .htm Non-T ech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.gigabyte.com.cn Shanghai TEL: +86-021-63410999 FAX: +86-021-63410100 [...]