Graco 312964C manual

The Matr ix Tank Lev el Monitor co ntains an R F device w ith the fo llowing appro vals: FCC ID: TFB-FREEST AR IC: 5969A-FREEST AR Industry Canada Statement The term “IC” before t he certification/reg istra- tion number only signifies tha t the Industr y Canada technical specifications were met. ✓ N14939 - FREESTAR ZFMSM-101 -1 (CEL) / FS24-1[...]

Warnings 2 312964C Wa r n i n g s The f ollowing warnings are f or the setup , use, groundin g, maintenance, and repair of this equ ipment. The exclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk. Refer bac k to these wa r nings. Additional, pr oduct- specific warnings ma y be found [...]

Set Up 312964C 3 Set Up Dips witch Settings The TLM has two , 4 - position dips witches labeled S1 and S2. TLM dips witches must be set to match those of the transceiver the TLM will be communicating with. The f actor y default setting for all TL M’ s is (‘1’ ‘1’). The first ‘1’ refers to the Network ID and the sec ond ‘1’ refers [...]

Set Up 4 312964C 7. Install tw o, 9-v olt alkaline batteries (1). Be sure that the batter ies fully engage the mounting clips by pushing on the botto m of each battery with your thumb . 8. Replace insulating f oam (4). 9. Replace co ver (7) and secure it with the f our screws (3). It will take about 30 seconds f or the monitor to dis- play inf or m[...]

Set Up 312964C 5 Dipswitc h Setting for Netw ork ID and T ransceiver ID See F IG . 3 f or dips witch setting configur ations. b The batteries must be di sconnected and remov ed before changi ng dips witch settings or the TLM will not be able to communic ate with the PC software. F IG . 3 1 - def ault S2 Transceiver ID 12 3 4 S2 on 2 12 3 4 S2 on 3 [...]

Set Up 6 312964C Registering the TLM Graco recommend s registering TLM prior to installa- tion. The TLM operating pa rameters are cont rolled by the Matrix PC Software and setup by the System Adminis- trator . See the Matrix 3 Software instruction manual f or the PC setup instructions. T o regist er the TLM : 1. Set TLM to correct NETWORK ID and TR[...]

TLM Display 312964C 7 TLM Displa y (See F IG . 6, page 8) TLM ID - Unique number assign ed to the TLM to distin- guish it from oth er TLM’ s in the syst em. Batter y Life - Remaining lif e of the unit’ s batter ies. Sys- tem Administrator on Matr ix PC Software d eter mines when Low Batter y W ar n ing message is ge nerated. Netw ork ID and T r[...]

TLM Registration Process 8 312964C TLM Registration Pr ocess F IG . 5 Press & Hold DISPLA Y button Battery NW ID TX ID REGISTER MODE Ack received from T ransceiver No Ack received from T ransceiver TLM ID TLM ID TLM ID BLANK BLANK VERSION xx.xx.xx VERSION xx.xx.xx PC Responds with Registration Ack Message PC doesn’t Respond REGISTER COMPLETE [...]

Installation 312964C 9 Installation 1. Remo ve the b ung fitting and scre w in the TLM hand-tight. DO NOT use a wrench to tighte n as this ma y damage the TLM. Do not use thre ad lock adhe- siv e as this may d amage the TLM. 2. The TLM m ust be mounted with in 2 degrees from per pendicu lar to the surface of the fluid. A lev el that measures degr e[...]

Viewing Data 10 312964C Vie wing Data Press and release th e Display b utton (A). Data appears on displa y (B); each screen lasting a f ew seconds bef ore going on to the next. See F IG . 8. After a tank is refilled from an oil distributor or a waste oil tank is emptied b y a waste oil ser vice provide r , press the Display b utton on the TLM to en[...]

Troubleshooting 312964C 11 T r oubleshooting Prob lem Cause Solution Brand new monitor’ s dis- pla y is very dim. Unit is shipped with protective coat- ing o ver displa y . Remo ve protecti ve coating. Monitor displays “In valid Reading”. The TLM reading is outside of the programmed size parameters. V er ify the programmed parame te rs and re[...]

Troubleshooting 12 312964C Monitor readings are inaccurate. T a nk geometr y incorrectly defi ned. See T ank Lev el Monitor Software Guide or PC Software Guide fo r d e t a i l s . T a nk Lev el Monitor has not be en updated with latest adjustments made within The profile ID on the PC . Manually pu sh DISPLA Y button on TL M T wo TLMs are pr ogramm[...]

Service 312964C 13 Service Once the T ank Lev el Monitor has been in stalled, no additional maintenance or ser vice is necessar y , with the excep- tion of replac ing batteries. Replacing Batteries Alwa ys repl ace bot h batteries with two new 9- volt alkaline batte r ies whene ver y ou change batteries in the TLM. 1. Remove the four cov er screws [...]

Parts 14 312964C Pa r t s 3 2 1 1 Remov e protective cov er used for shipping before programming. Do not remov e. This is required to mainta in intrinsic safety approv al. 1 2 4 2 ti12033a 5 6 7 8 9 10 Ref. No. P ar t No. Description Qty 1 BA TTER Y , 9 volt (purch ased locally) 2 2 126752 GASKET , sensor , ultr asonic 1 3 117467 SCREW , self tappi[...]

Technical Data 312964C 15 Te c h n i c a l D a t a NO TE: FCC, C-Tic k and IC approvals are f or the RF device contained in the Matrix T ank Lev el Monitor (TLM). Ultrasonic T ank Depth Measurement rang e 0 - 30 ft. (0 - 9 m) Not f or use in pressurized t anks. Fluid Le vel Me asurement Accuracy +/- 0.5% Mounting Standard 2 in. (n pt) bung. Height [...]

Dimensions 16 312964C Dimensions A 9.1 in (231 mm) B 4.9 in. (124 mm) 1-1/2 in. npt A B 2 in. npt ti12031a[...]

Tank Geom etry 312964C 17 Ta n k G e o m e t r y V ertical T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank walls must be uniformly ve r tical from empty lev el to full F IG . 10 ti12693a Maximum Height 30 ft. (360 in.)[...]

Tank Geomet ry 18 312964C Cylindrical T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank end walls m ust be flat; th ey cannot be any other shape , including belled. F IG . 11 ti12695a Maximum Length Maximum Height 30 ft. (360 in) 30 ft. (360 in)[...]

Tank Geom etry 312964C 19 Obround T ank: • Maximum V olume = 999, 999 gallons or liters . • T ank end walls m ust be flat; the y cannot be any other shape inclu ding belled. F IG . 12 ti12694a Maximum Width 30 ft. (360 in .) Maximum Length Maximum Height 30 ft. (360 in) 30 ft. (360 in)[...]

All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents. Original Instructions. This m anual co ntains English. MM 312964 Graco Headquarters: Minneapoli[...]