Haier WNM800TE manual

Automatic Drum W ashing Machine WNM1000TE WNM800TE T able of Contents Before using Names of Parts---------------------------------inside front cover Matters Needing Attention-------------------------------------1-3 Installation---------------------------------------------------------4-5 Control Panel-------------------------------------------------[...]

Names of Parts T able Cover Program Knob Operation Button Drainage hose clip Back plate Packing bolt (3) W ashing Allocating box W ash Door Observing Glass Window Drainage hose Earth terminal Power supply cable Back plate screw (3) Caution and W arning symbols For your safety and to prevent damages to the washing machine, any instructions in this m[...]

Safety 1. A separate earthed socket is required for the power supply . After installation of the washing machine,the power plug should be accessible during the normal wash. 3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine techni- cian or a Haier designated service point for power cable replacement. 5. Do not use fla[...]

Matters Needing Attention 2 Use ƽ[...]

9. Keep the door slightly open when the washing machine is not being used. Never cover the machine with a plastic sheet. 4. Do not wash foam rubber or similar sponge materials. 5. Before washing, do up zippers, buttons , laces and repair damaged areas,under- wear or small articals should be placed in the laundry bag or a pillowslip. Do not wash clo[...]

As shown in figure1 remove all the packing materials (including the foam base). Fig 1 Check attachments and materials. 3 Name Qty Model Operational manual Quality certificate Wa t e r hose Drainage holder Plastic plugs 1 1 1 WNM1000TE WNM800TE 1 Remove the packing screws as shown in figure 2. The packing bolts protect the appliance from shock durin[...]

Connection of water inlet hose and washing machine W a t e rd r a i n a g eh o s e Connection of power supply The height of the terminal of the water drainage hose should be between 80cm-100cm, the water drainage hose must be securely placed on the clip on the back of the washing machine. Use the water drainage support supplied as an accessory for [...]

6 Control Panel T urn the knob at "0", then turn off the power and turn the program knob for setting desired wash program. The program knob will not rotate with the programmed washing process. 90 80 70 60 50 40 30 1/ 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 90 80 70 60 50 40 30[...]

7 Operational Functions Economic W ash button Note: Select this function when "Cotton" "Synthetics", "W ool" or "Silk" (programs 1-12) is selected.  No Soak Button F or t h e s yn t h et i c s c y cl e an d t he w oo l c y cl e, pu s h t h e b ut t on d ow n , t h e a nt i c re as e f u nt i on wil l b e s[...]

Program Selection 8 Intense Prewash Normal Middle Delicate Normal Middle Delicate Normal Delicate Normal Delicate Silk 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 V ery heavy soil Non-fade heavily soiled woolen fabrics Fading and medium soiled woolen fabrics Non-fade heavily soiled silk fabrics Fading and medium soiled silk fabrics End Spin Rinse Quick M[...]

1. Power supply Plug in the power supply 220V~240V/50Hz. 3. Laundry treament 5.W ash Load 2. W ater supply T urn on the tap ensure that the water is clear . Caution: Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak. sort out clothes according[...]

1. Laundry loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Note: 1) When first using the washing machine, let it run un- loaded for one program to pre- vent the laundry from being tainted by oil or dirty water from the washing machine. 2) Do not overload the washing machine. 2. Use of de[...]

11 7. End W ait 2-3 minutes after the washing process is finished , press the power button again to cut off the power supply . Open the door to take out the laundry . T urn off the tap and unplug the washing machine. 5. Selecting the function button Select function buttons as required (refer to the directions printed on the control panel) , otherwi[...]

Other Functions 1. Power-off memory funtion: This machine has a power-off menmory funtion. In case of abrupt power failure or the power must be cut off during a program cycle, the present settings will be saved, and operation will resume when the power is switched on again. 2. T rouble messages: judge the malfunctions from door lock light Error 1: [...]

Insert the bolts. 5. If the machine is to be moved a distance location, replace the vibration mounting locks which were re- moved during installation as shown below. 1. T urn of the water and electricity supply af- ter every wash. Open the door to prevent the formation of moisture and odors. If the wash- ing machine is left idle for a long period, [...]

The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem Possible Cause The washing machine fails to operate Poor connection to power supply Power failure Door is not properly closed Machine has not been switched on W ashing machine does not fill with water Water is[...]

Maximum power (W) Model Maximum working current (A) W ater pressure (MPa) W ashing power (W) Spinning power (W) Max. washing load (kg) Spinning speed (r/min) Size (HXDXW) (mm) W eight (kg) WNM1000TE 220V~240V/50Hz 15 0.03 P 1 2 3 0 4 00 5 15 2 0 00 65 10 00 850x520x595 Item Power supply W ashing program T echnical Specification WNM800TE 220V~240V/5[...]

W iring Circuit 16 Motor R S T M1 M2 M3 M5 M7 M8 CN1-2 CN2-1 CN1-3 CN1-1 CN3-3 CN3-1 CN2-2 CON3 CN2-3 CN2-4 CN2-5 CN2-6 CON3 CN3-3 CN3-4 CON2 CON1 CN6-3 CN6-4 PCB NTC SW N G L FA MRN MRL MRC MR EVF EVP PS EVC R 12 13 14 11 P PCB-Printed Circuit Board Motor-Motor MR-Door Lock R-Heating Element PS-Drain Pump P-Pressure Switch EVP ,EVF-Cold water V al[...]