Harbor Freight Tools 47613 manual

ASSEMBL Y AND OPERA TING INSTR UCTIONS PROFESSIONAL 9” CIRCULAR SA W W/BLADE 47613 Diagrams within this manual may not be drawn proportionally . Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight T ools ® . 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 V[...]

PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual for the saf ety warnings and precautions, assembly , op- erating, inspection, maintenance and c leaning procedures, par ts list and assem- bl y diagram. Keep y our in v oice with this manual. Write the in v oice number on the inside of the front co ver . Keep this manual and in [...]

ELECTRICAL SAFETY 4. Grounded tools m ust be plugged into an outlet properly installed and grounded in accor dance with all codes and ordinances. Never remove the grounding pr ong or modify the plug in any way . Do not use any adapter plugs. Check with a qualified electrician if y ou are in doubt as to whether the outlet is properl y gr ounded. If[...]

12. A void accidental starting. Be sure the P ower Switc h is off before plug ging in. Carr ying power tools with y our finger on the P ower Switch, or plugging in pow er tools with the P ower Switch on, in vites accidents. 13. Remove adjusting ke ys or wrenches bef ore turning the power tool on. A wrench or a k ey that is left attached to a rotat[...]

23. Use only accessories that are recommended b y the manufacturer f or y our model. Accessor ies that ma y be suitable f or one tool may become hazardous when used on another tool. SER VICE 24. T ool service must be perf ormed only b y qualified repair personnel. Ser vice or maintenance perf or med b y unqualified personnel could result in a ris[...]

11. Never touc h moving parts . Ne v er place your hands , fingers or other body par ts near the tool’ s moving par ts. 12. Never operate without automatic guar d return in place . Do not disable blade guard when cutting. 13. Guard a gainst kickbac k . Kickbac k occurs when the saw stalls and is driv en backw ards tow ard the operator . When thi[...]

GR OUNDING W ARNING! Improperl y connecting the gr ounding wire can result in the risk of electric shock. Check with a qualfified electrician if y ou are in doubt as to whether the outlet is properl y gr ounded. Do not modify the power cor d plug provided with the tool. Never remove the gr ounding pr ong from the plug. Do not use the tool if the [...]

FIGURE B DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 4. T ools mar k ed “Double Insulated” do not require grounding. They ha v e a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Elect[...]

6. If you are using an e xtension cord outdoors, mak e sure it is marked with the suf- fix “W -A” (“W” in Canada) to indicate it is acceptab le f or outdoor use. 7. Make sure y our extension cord is properly wired and in good electrical condition. Alwa ys replace a damaged extension cord or ha v e it repaired by a qualified elec - trician[...]

UNP A CKING When unpacking, chec k to mak e sure all the par ts shown in Figure C are included. If an y par ts are missing or broken, please call Harbor F reight T ools at the number sho wn on the cov er of this manual as soon as possib le. ASSEMBL Y AND OPERA TING INSTR UCTIONS NO TE: For additional inf or mation regarding the par ts listed in the[...]

Prepare Material Before Cutting 1. Suppor t large panels to minimize risk of blade pinching and sa w kickback. 2. Use the supplied Rip Guide (402) when ripping mater ial b y sliding it into the Base Assy . and tightening Wing Bold (58). See Figures F and G below . 3. Securely clamp material to be cut to work bench. 4. Mak e sure saw does not cut in[...]

Cutting Caution: V erify that saw blade is securel y tightened and both angle and height adjusting knobs are tight. 1. If desired f or a straight cut, slide the Rip Guide (402) into the side of the Circular Saw and tighten with Wing Bolt (58), or clamp a straight edge to the material to guide the saw on a str aight path. 2. Place the sa w Base Assy[...]

Replacing the Carbon Brushes 1. Unscre w the Brush Caps (30). 2. Pull out the Carbon Brush (29) from each side of the motor and e xamine them. If the y are wor n more than half w a y down, replace them. It could be that they are simply dir ty . The y can be cleaned using an ink eraser . 3. Replace the Brush Caps. Installing a New Sa w Blade 1. Alw [...]

P arts List NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not av ail- able individually as replacement parts. SKU 47613 P age 14 P art # Description P art # Description 1 Screw 38 Int. Ret. Ring 3 Housing Assy . 39 Ball Bearing 4 Screw 40 Key 6 Name Plate 41 Spindle 7 Cord Suppor t 42 Bearing Housing 8 Cord 43 S[...]

ASSEMBL Y DIA GRAM THE MANUF ACTURER AND/OR DISTRIBUT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF ACTURER OR DIS TRIB UT OR MAKE S ANY REPR ESE NT A TION OR W AR RANT Y OF ANY KIND T O THE BUY ER THA T HE OR SHE IS QU ALIFIED T O MAKE ANY REP AIRS T O THE PRODUCT , OR THA T [...]

LIMITED 1 YEAR W ARRANTY Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or[...]