Harbor Freight Tools 91062 manual

3-1/4” ELECTRIC PLANER Model 91062 OPERA TING INSTR UCTIONS Due to continuing improv ements , actual product ma y diff er slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at: http://www .harborfreight.com Cop yr ight 2003 b y Harbor F reight T ools ® . All r ights reserved. No por tion[...]

PR ODUCT SPECIFICA TIONS SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and as- sembl y diagram. Keep y our in v oice with this manual. Write the in v oice number on the inside of the front co ver . Keep this manual and in voi[...]

3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with a[...]

11. Dress properl y . Do not wear loose clothing or je welry . Contain long hair . Keep y our hair , clothing, and gloves a wa y from mo ving par ts. Loose clothes, je welr y , or long hair can be caught in moving par ts . 12. A v oid accidental star ting. Be sure the P ower Switch is off bef ore plugging in. Carrying power tools with your finger o[...]

20. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that ma y affect the tool’ s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly main- tained tools. 21. Use only accessories that are recommended by the manufacturer for your model. Accessor ies that ma y [...]

3. Y our tool m ust be plugged into an appropriate outlet, proper ly installed and grounded in accordance with all codes and ordinances . The plug and outlet should look like those in the f ollowing illustr ation. (See Figure A.) FIGURE A SKU 91062 P A GE 6 DOUBLE INSULA TED T OOLS: T OOLS WITH TWO PR ONG PLUGS 4. T ools mar k ed “Doub le Insulat[...]

SKU 91062 P A GE 7 EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, res[...]

FIGURE D SKU 91062 P A GE 8 SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V olts Alternating Current Amperes No Load Revolutions per Minute (RPM) n o xxxx/min. A V ~ SPECIFIC SAFETY RULES 1. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace[...]

8. Use ey e and breathing protection. Alwa ys wear ANSI approv ed saf ety impact eye goggles and dust masks or a respirator when working with this product. 9. Always turn off the Planer and unplug the unit from its electrical outlet before performing any maintenance, or changing accessories. 10. Never leave the Planer unattended when it is plugged [...]

on their own. Do not press against the Kniv es to stop them. Alwa ys keep hands and fingers clear of spinning Blades. 23. Do not for ce the Blades into the workpiece being cut. Apply moderate pres- sure, allowing the Blades to cut without being forced. 24. Never attempt to remove material stuck in the moving parts of the Planer while it is plugged [...]

OPERA TING INSTR UCTIONS NOTE: For additional information regarding the parts mentioned in the following pages, ref er to the Assemb l y Dia gram on pa g e 17. SKU 91062 P A GE 11 The Power Switch: 1. The T r igger (16) of the Planer f eatures a Safety Loc k Button (17) to ensure against accidental star ting of the tool. T o star t the tool, depres[...]

SKU 91062 P A GE 12 The Guide: 1. The Guide (64) can be used to adjust the width of cut, suppor t the Planer , and keep the Planer from drifting away from the cut line (i.e., the edge of a door). The Guide may be attached either to the right side of the Planer or on its left side. T o do so , position the Planer on the wood stock that is to be cut.[...]

SKU 91062 P A GE 13 the wood stoc k . Then, transfer pressure to the Rear Base Plate , and continue planing slowly to the end of the cut. Do not pull the Planer back over the surface already cut. (See Figure G.) 6. If necessar y , repeat Step #5, using progressiv ely deeper cuts until you near the desired depth. Then, readjust the Depth Knob (48) t[...]

SKU 91062 P A GE 14 driver (not included) to remov e the two Carbon Brush Caps (35). Then, remov e the two Carbon Brushes from the Brush Holders (38). If a Carbon Brush is worn down more than 1/2 of its original length, replace both Carbon Brushes. If, how- e ver , the Carbon Brushes are just dir ty they ma y be cleaned by r ub bing them with a pen[...]

SKU 91062 P A GE 15 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF A CTURER AND/OR DISTRIBUTOR HAS PR O VIDED THE P ARTS LIST AND ASSEMBL Y DIA GRAM IN THIS MANUAL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF A CTURER OR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE IS QU ALIFIED T O MAKE ANY REP [...]

Part # Description Qty. Part # Description Qty. 1 Name Plate 1 33 Screw Arbor 1 2 Tap Screw (8SEABB04-18) 3 34 Spring 1 3 Cover 1 35 Carbon Brush Cap 2 4 Belt 1 36 Carbon Brush 2 5 Bearing Sleeve 1 37 Carbon Brus h Sl eeve 2 6 Bearing (8SG6000Z-01) 1 38 Carbon Brush Holder 2 7 Press Board 1 39 Rear Cover 1 8 Tap Screw (8SEABB04-8) 2 40 Stopper 1 9 [...]

SKU 91062 P A GE 17 17 16 18 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustration pur poses only , and are not available individually as replacement parts. 68: GUIDE NOT SHO WN.[...]