Heat & Glo LifeStyle fb-grand manual

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 1 HOT! DO NOT TOUCH . SEVERE BURNS MA Y RESUL T . CLOTHING IGNITION MA Y RESUL T . Model(s): FB-GRAND FB-IN • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light a[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: ____________________ Dealership purchased from: ___[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 3 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. BTU Speci fi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. High Altitude Installations . . . . . . . . . . . . . . [...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 4 Note : T o assure top performance, safety and ef fi ciency , inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions. Not e: This installation must c onform wi th local c odes. In the absenc e of local c[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 5 Heat & Glo gas inserts are designed for recessed installa- tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes. Prior to installing the gas insert: • Hav[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 6 3 3 F ireplace Size Requirements A. Minimum Fireplace Opening Minimum fi replace opening requirements are shown in Figure 3.1. • The fi rebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built fi rebox in order to gain minim[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 7 B. Clearances Figure 3.2 Clearances to Mantels or other Combustibles above Appliance Fire Risk. • Locate and install appliance to all clearance speci fi cations in manual. Fire Risk. Odor Risk. • Clearance to combustible material under the insert is 1/4 inch (0.6 cm). • Use le[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 8 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.1 speci fi es minimum vent heights for various pitched roofs. Roof Pitch H (Min.) Ft[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 9 CAUTION ALL vent speci fi cations MUST be followed. • This product is tested and listed to these speci fi cations. • Appliance performance will suffer if speci fi cations are not followed. Figure 5.1 C. Measuring Standards V ertical measurements listed in the vent diagram (Fig[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s speci fi cation. • Local building codes required by authority having jurisdiction. • NFPA 211 Prep[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 11 A. V enting Components 7 7 Installing V ent P ipe and Appliance The vertical vent termination system installed on this model includes: • One 3-foot section stainless steel fl exible pipe (included with insert). • One length of 3-inch fl exible vent pipe for combustion air (inc[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 12 Figure 7.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 7.2). • Place 3/8 inch bead of 300º F silicone on fl ue tile top. C. Placing, Securing and Leveling the Applian[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 13 D. Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.2) . T o install adaptor see Figure 7.3. Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........1.25* Over[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 14 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. • Check all fi ttings and connections of appl[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 15 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury . HIGH AL TITUDE INST ALLA TIONS U.L. Listed gas appliances are tested and approved without requiring changes for e[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 16 A. Wiring the Appliance 9 9 Elect rical Infor mation Note : This appliance must be electrically wired and grounded in accordance with local codes or , in the absence of local codes, with National Electric Code ANSI/NFP A 70-latest edition or the Canadian Electric Code, CSA C221.1. O[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 17 B. Junction Box Installation Figure 9.2 Junction box installation JUNCTION BOX SIDEW ALL FEED PLUG THROUGH HOLE INSERT STRAIN RELIEF AROUND CORD IN THIS END FROM OUTSIDE OF UNIT SCREW PROVIDED Optional Accessories Connecting the electrical junction box is required if using a blower [...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 18 Figure 9.4 Fan Wiring Diagram NOTE: IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 0 C RA TED WIRE. JUNCTION BOX V ARIABLE SPEED CONTROL TEMPERA TURE SENSOR SWITCH WHT GRN BLK BLK 1 10-120 V AC BLOWER BLOWER RECEPT ACLE[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 19 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. 1 0 10 F inishing Figure 10 .1 Clearances to Mantels or oth[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 20 Figure 1 1.1 Placement of Embers EMBER MA TERIAL (TOP SURF ACE, AND FRONT) BURNER P AN AIR SHUTTER 1 1 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have acc[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 21 Log Set Assembly: LOGS-CFXGB E. Positioning the Logs This model uses locating tabs to positively locate the logs with respect to the grate assembly . Please refer to grate assembly . LOG NUMBER 1 (SR V768-701): Place log #1 onto the grate. Push log back until it rests against locati[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 22 LOG NUMBER 3 (SR V768-705): Position log #3 onto grate such that tab E fi ts into slot on bottom surface of log. Push down until log is sitting fl at on grate. LOG NUMBER 4 (SR V582-705): Place log #4 across both fl at spots on log #1 and log #3, with the “Y” in log #4 placed[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 23 LOG PLACEMENT IN- STRUCTIONS Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 773-936 3/03 GRA TE ASSEMBL Y This model uses locating tabs to positively locate the logs with respect to the grate assembly . Please refer to grate assembly . LOG #1 (SR V773-701):[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 24 LOG #2 (SRV773-702): Position Log #2 onto grate such that tab C fi ts into the slot on bottom surface of log. LOG #3 (SR V768-704): Position log #3 onto grate such that the tabs D and E fi t into the slots on bottom surface of log and the right back side of log is fl ush against [...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 25 Figure 1 1.16 Glass Assembly F . Glass Assembly Removing Glass Assembly There are two glass latches on the bottom of glass assembly . • T o release glass assembly , pull latch forward and allow to retract away from glass assembly . • Remove glass assembly after both latches have[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 26 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before operating this appliance have a quali[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 27 B. Lighting Appliance Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise to OFF”. Do not force. 5. Clo[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 28 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1. D. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 29 E. Frequently Asked Questions Fire Risk. High T emperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air . • Do NOT place combustible items on top of or in front of appliance. • Keep furniture, draperies away from applianc[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 30 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service person in the d[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 31 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater t[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 32 1 4 14 Maintaining and Ser vicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a quali fi ed service technician should perform an appliance checkup at the beginning of each heating season. Annual inspection[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 33 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary . 3. V erify no obstructions to air fl ow thro[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 34 Figure 15.1 Appliance Dimensions D F E H G ELECTRICAL ACCESS (IF EQUIPPED) GAS INLET C A B 2-1/16 in. 52 mm 1-9/16 in. 40 mm 3-9/16 in. 91 mm 1-1/16 in. 28 mm 2-1/2 in. 64 mm 4 in. 102 mm 13-3/4 in. 350 mm 3-1/8 in. 80 mm 6-5/8 in. 169 mm Tw o ø 2-13/16 in. 71 mm 9-9/16 in. 142 mm [...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 35 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 15.2) LINK-DV -30B or (LINK-DV -30): Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter . LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch fl ex line[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 36 Service Parts Service Parts Diagram FB-GRAND Beginning Manufacturing Date: 8-02 Ending Manufacturing Date: ______ Part number list on following page. 5 6 7 8 9 10 11 12 13 14 15 16 17 17 19 Log Set Assembly 1 2 3 4[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 37 Service Parts List (NG, LP) FB-GRAND IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts. A V AILABLE TO SHIP IN 24 HOURS ITEM DESCRIPTION SERIAL[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 38 Part number list on following page. Service Parts Service Parts Diagram FB-IN Beginning Manufacturing Date: 8-02 Ending Manufacturing Date: ______ 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 2 3 4[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 39 Service Parts List (NG, LP) IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts. A V AILABLE TO SHIP IN 24 HOURS ITEM DESCRIPTION SERIAL # P ART [...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 40 © 2005 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY HEA T & GLO GAS APPLIANCE PRODUCTS 060-981D 3/05 D. Limited Lifetime W arranty BASIC ONE-YEAR W ARRANTY . HEA T & GLO, a brand of HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevar[...]

Heat & Glo • FB-IN, FB-GRAND • 783-908 Rev . J • 2/07 41 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com E. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer ,[...]