IBM L200p manual

L200p User's Guide IBM ThinkVision TM Monitor L200p English[...]

ii i First Edition ( April/2004) Note: For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor.[...]

ENGLISH 1 Safety (Read first) .......................................................................................................2 Setting up the monitor ...............................................................................................5 Product description ...........................................................................[...]

2[...]

ENGLISH 3 Always observe the following precautions to reduce the risk of injury and property damage. Do not attempt to service a product yourself unless instructed to do so by the IBM Support Center. Use only an IBM authorized service provider who is approved to repair your particular product. Note: Some parts can be upgraded or replaced by the cus[...]

4 Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cords. Connect and disconnect the equipment from the electrical outlet carefully. All IBM personal computers contain a non-rechargeable coin cell battery to provide pow[...]

ENGLISH 5 Setting up the monitor Handling instructions 1. Lift the monitor by placing your hands where indicated by the arrows in the figure below. 2. Before using your monitor for the first time, remove the clear protective film from the front of the screen. Product description The IBM ThinkVision Monitor, L200p, is a TFT LCD Color Monitor. It req[...]

6 Kensington security slot 3. Before adjusting your monitor for the first time, remove the locking clip on rear of the stand. Carefully hold the screen of the monitor and squeeze the locking clip to remove. This action is shown in figure below. This slot can be used to connect to a locking cable. Locking cables can be purchased separately at most c[...]

ENGLISH 7 i With the IBM Flat Panel Monitor, you can adjust the position in various ways for maximum comfort. Viewing angle You can tilt the screen forward and backward as shown below in Figure A. Swivel You can swivel the screen to the left or the right as shown below in Figure A. Height You can adjust the height of the screen as shown below in Fi[...]

8 Be sure to turn off the power before you perform any maintenance on the monitor. Clean your monitor as follows: • Do not use solvents or abrasives. • Gently wipe the covers and the screen with a soft cloth. • Remove finger marks and grease with a damp cloth and mild detergent. • Never use flammable cleaning materials to clean your IBM mon[...]

A ENGLISH 9 Connecting your monitor 1. Turn off your computer and all attached devices. Next, unplug all power cords to your computer and all attached devices. 2. Connect the signal cable. • The analog signal cable is already connected to your monitor. See in Figure A. • When connecting the analog signal cable, connect the free end of the attac[...]

10 1. Switch on your computer. 2. Switch on the monitor power source by pushing the power switch on side rear panel of the monitor. See Figure B on page 9. 3. Switch on your monitor by pushing and releasing the power switch marked " " at the front of the bezel. • To switch off your monitor, push and release the power switch again. 4. To[...]

ENGLISH 11 To install the device driver in Microsoft ® Windows ® 95 or Windows 98, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 95 or Windows 98. 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. [...]

12 To install the device driver in Microsoft Windows 2000 Professional or Microsoft Windows Millennium Edition (Me), do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows 2000 or Windows Me. 1. Turn off the computer and all attached devices. 2. Ensure that the m[...]

ENGLISH 13 To install the device driver in Windows XP, do the following: Note: You must download files from the User’s Guide and Installation Files CD to use the Plug and Play feature in Windows XP. 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit[...]

14 For digital input, image setup is not required. When you first use your monitor, you must perform Auto Setup for analog input. If you are using digital input, continue with the instructions on page 9. This procedure sets up your monitor to process the video signals from your computer without image discoloration or smearing. After you perform Aut[...]

ENGLISH 15 Image setup for DOS i If the monitor is in standby mode, it may automatically turn off while you are waiting for it to warm up. If this happens, switch off the monitor and switch it on again after a few seconds. i If you are using PC-DOS/V, change to U.S. mode by typing CHEV US and pressing enter at the command prompt. i The size and div[...]

6. When the dot pattern appears, pr ess the " " b ut ton at the bottom of the monitor. This activates the Image setup procedure, which will optimize the display settings with the provided dot-patterns. •The screen will momentarily turn black while auto adjustment proceeds. 7 . When finished, the Image setup message disappears and the sc[...]

Normally, you can complete the setup procedure using Automatic Image setup ; however, if your screen image is still distorted after you perform Image setup or the setup CD does not run on your system, perform M anual Image setup. To manually adjust the image setting, do the following: 1. Turn on the monitor and wait approximately 15 minutes for it [...]

18 Adjusting your LCD monitor User controls USER CONTROL FEATURES i The image is already optimized for many display modes, however the user controls can be used to adjust the image to your liking. i The settings are saved after adjustment and when exiting the OSD and will be effective thereafter. Icon Direct access functions Switches the monitors o[...]

ENGLISH 19 The settings adjustable with the user controls are viewed through the On - Screen Display (OSD). Press the ent er b ut ton " " to display the main OSD menu. Initial appearance of OSD On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day. Thus, to achieve [...]

20 OSD Icon Select the Color mode you find most comfortable or fine tune the colors using the Custom menu, if necessary. Description Sub-menu(s) • Clock • Phase • Save Increases or decreases redness Increases or decreases greenness Increases or decreases blueness Preset • 6500K (Pink White) • 7200K (Normal White) • 9300K (Blue White) Cu[...]

ENGLISH 21 Use this button to make the analog or digital connector active. This feature is used when two computers are connected to the monitor. The default setting is analog. Input Signal • English • Fran ç ais • Italiano • Deutsch • Espa ñ ol • OSD Icon Displays the detailed information of mode, model name and microcode. Description[...]

22 i If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT monitor temporarily until you have reconfigured the computer, preferably to 1600 x 1200 at 60Hz. The display mode the monitor uses is controlled [...]

ENGLISH 23 To benefit from power management, the monitor must be used in conjunction with a computer that implements the Video Electronics Standards Association (VESA) Display Power Management Signaling (DPMS) Standard. The power management feature is invoked when the computer recognizes that you have not used your mouse or keyboard for a user-defi[...]

24 T roubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem No power to monitor. Possible cause Suggested action Reference Brightness and Contrast may be too low. The monitor is in the Po[...]

ENGLISH 25 i For image problems, you may want to run Image setup again before referring to this section. In most cases, Image setup can fix the problems. See Automatic Image setup for the computer on page 14 for details. Problem Possible cause Suggested action Reference There are noises in the video signal The color setting may be incorrect. A smal[...]

26 If you are unable to correct the problem yourself, you may seek further help as follows: Call the IBM Service and Support. In the U.S.A and Puerto Rico call 1-800-426-7378 In Canada (Toronto only) call 416-383-3344 In Canada (all other) call 1-800-565-3344 In other countries contact your dealer, retailer, or other IBM authorized service represen[...]

ENGLISH 27 i Power consumption figures are for the monitor and the power supply combined. Specifications This color monitor (Type-model 6736-HC9) uses a 20.1-inch TFT LCD. Weight 9.3 kg (20.50 lbs) With Stand: 20.1 inch (510.54 mm) 306 mm (12.05 inch) 408 mm (16.04 inch) 0.255 mm (H) x 0.255 mm (V) 100 - 240 Vac 60/50 ± 3Hz 1.2A < 65 W < 2 W[...]

28 FRU Monitor FRU Stand FRU Video Cable FRU Video Cable Hybrid Hybrid Analog Digital BB BB Black Black 6736-HC9 6736-HC9 6736-HC9 6736-HC9 WW WW WW WW Service information The following parts are for use by IBM service, or IBM authorized dealers, to support the customer warranty. Parts are for service use only. Model T ype 6736 Description P/N Vide[...]

ENGLISH 29 Notices and trademarks This section contains information on notices and trademarks. Notices IBM may not offer the products, services, or feature discussed in this document in all countries. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product,[...]

30 Trademarks The following terms, used in this publication, are trademarks or service marks of the IBM Corporation in the United States, other countries, or both; IBM IBM logo ThinkPad ThinkVision E NERGY S TAR and the E NERGY S TAR logo are U.S Govt. registered trademarks. Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation[...]