Integra DTR-5.5 manual

DTR-6.5/5.5 Instr uction Manual AV Receiv er DTR-6.5,5.5_En.book Page 1 Wednesday, July 28, 2004 9:07 AM[...]

2 Important Safety Instructions 1. Read these instructions. 2. K eep these instructions. 3. Heed all w arnings. 4. F ollow all instructions. 5. Do not use this apparatus near w ater . 6. Clean only with dry cloth. 7. Do not block an y ventilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y he[...]

3 Precautions F or U .S. Models Note to CA TV system installer: This reminder is provided to call the CA TV system installer’ s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in partic- ular , specifies that the cable ground shall be connected to the grounding system of the building, as close to the po[...]

4 Precautions —Continued F or British models Replacement and mounting of an A C plug on the po wer supply cord of this unit should be performed only by qualified service personnel. IMPOR T ANT The wires in the mains lead are coloured in accordance with the following code: Blue: Neutral Brown: Li ve As the colours of the wires in the mains lead o[...]

5 Features Amplifier • 7-channel amplifier • Optimum Gain V olume Circuitry • Zone 2 capability • 24-bit/192 kHz D/A con verters • WRA T (Wide Range Amplifier T echnology) • Color-coded speak er terminal posts A udio/Video • Dolby *1 Digital, Dolby Digital EX, Dolby Pro Logic IIx • DTS *2 , DTS-ES Discrete, DTS-ES Matrix, DTS Neo[...]

6 Ta b le of Contents Basic Introduction Important Safety Instructions .......................................................................................... 2 Precautions ....................................................................................................................... 3 Supplied Accessories................................[...]

7 Ta b le of Contents —Continued Adv anced Controlling Other Components Entering a Remote Control Codes................................. 80 Learning Commands from Another Remote Controller ..................................................................... 88 Using Macros................................................................... 89 Adv[...]

8 Fr ont & Rear P anels Front P anel Standby Zone 2 1 Z Y W V U X 5 6 7 89 J K M N Q T S O P R L 2 3 4 Standby Zone 2 1 Z Y W V U X 5 6 78 J K L N O R T P Q S M 2 3 4 9 DTR-6.5 DTR-5.5 DTR-6.5,5.5_En.book Page 8 Wednesday, July 28, 2004 9:07 AM[...]

9 Front & Rear P anels —Continued For detailed information, see the pages in parentheses. A Standby/On b utton (38) This button is used to set the A V receiv er to On or Standby . For models with a POWER switch, this b utton has no ef fect unless the PO WER switch is set to ON. B Standby indicator (38) This indicator lights up when the A V re[...]

10 Front & Rear P anels —Continued For detailed information, see the pages in parentheses. 1 MUTING indicator (54) This indicator flashes while the A V receiver is muted. 2 REC OUT indicator (64) This indicator lights up when the REC OUT is selected. 3 ZONE 2 indicator (77) This indicator lights up when Zone 2 is selected. 4 Listening mode &[...]

11 Front & Rear P anels —Continued For detailed information, see the pages in parentheses. A COMPONENT VIDEO IN 1, 2, 3 (28, 30, 32) These component video inputs can be used to con- nect A V components with component video outputs, such as D VD players. B AM ANTENNA (24) These push terminals are for connecting an AM antenna. C COMPONENT VIDEO[...]

12 Front & Rear P anels —Continued J OPTICAL DIGIT AL (27, 28, 30, 32, 34, 35) The DTR-5.5 doesn’t ha ve an IN 4 jack. The optical digital audio inputs can be used to con- nect CD and D VD players, and other components with an optical digital audio output. The optical output can be used to connect a CD recorder or other digital recorder wit[...]

13 Remote Contr oller Notes: • The batteries should last for about six months, although this will vary with usage. • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e [...]

14 Remote Controller —Continued In addition to controlling the A V receiver, the remote controller has sev eral operating modes for controlling your other A V components, including Integra compo- nents connected via . Modes are selected by using the remote controller’ s Remote Mode b uttons. For detailed information, see the pages in parenthese[...]

15 Remote Controller —Continued A Standby b utton (38) This button is used to set the A V receiv er to Standby . B On button (38) This button is used to turn on the A V receiv er. C Input Selector buttons (53) These buttons are used to select the input source. Only the RC-588M has a [PHONO] button. D Multi CH button (63) This button is used to se[...]

16 Remote Controller —Continued D VD mode is used to control an Integra D VD player connected to the A V receiver via . To set the remote contr oller to D VD mode, press the [D VD] Remote Mode button. A Standby b utton This button is used to set the D VD player to Standby . B On button This button is used to turn on the D VD player and to set it [...]

17 Remote Controller —Continued N A-B button This button is used to set the A–B repeat playback function. O Open/Close [ ] button This button is used to open and close the disc tray . P Video Off button This button is used to turn of f the internal video cir- cuitry , eliminating any possibility of interference. Q Clear button This button is us[...]

18 Remote Controller —Continued MD/CDR mode is used to control an Integra MiniDisc recorder or CD recorder connected to the A V receiver via . To select MD/CDR mode, press the [MD/CDR] Remote Mode button. By default, this b utton is set to control a MiniDisc recorder . T o control a CD recorder, it must be set to CDR (see page 80). A On button Th[...]

19 Remote Controller —Continued M FR & FF [ ]/[ ] buttons The FR [ ] button is used to start fast re verse. The FF [ ] button is used to start fast forward. N Stop [ ] button This button is used to stop playback. O Random button This button is used with the random playback func- tion. P Memory button This button is used with the memory playba[...]

20 About Home Theater Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of movement in your o wn home—just lik e being in a movie theater or concert hall. W ith D VDs you can enjoy DTS and Dolby Digital. W ith analog and digital TV you can enjo y Dolby Pro Logic IIx or Onkyo’ s o wn DSP surround[...]

21 Connecting the A V receiver • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Digital Jacks The A V receiver’ s optical digital jacks have shutter -type cov ers that open when an optical p[...]

22 Connecting the A V receiver —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table indicates the channels you should use depending on the number of speakers that you ha ve. *If you’re using only one surround back speaker, connect it to th[...]

23 Connecting the A V receiver —Continued Speaker Connection Precautions Read the following before connecting your speak ers: • American model only: Only connect speakers with an impedance of 6 ohms or higher . If you use speakers with a lower impedance, and use the amplifier at high volume le vels for a long period of time, the b uilt-in prot[...]

24 Connecting the A V receiver —Continued This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver won’ t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner . Connecting[...]

25 Connecting the A V receiver —Continued Connecting an Outdoor FM Antenna If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft. •F o[...]

26 Connecting the A V receiver —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiv er, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the A V receiver. The A V receiver supports se veral connection formats for compatibi[...]

27 Connecting the A V receiver —Continued Monitor Out ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V MONITOR OUT jack to a composite video input on your TV , as shown. ■ Using S-Video Use an S-V ideo cable to connect the A V receiv er’ s S MONITOR OUT jack to an S-V ideo input on your TV , as shown. ?[...]

28 Connecting the A V receiver —Continued Video Connections Y ou only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V D VD IN jack to the composite video output on your D VD player , as shown. ■ Using S-Video Use an S-V ideo cable to connect the A V re[...]

29 Connecting the A V receiver —Continued ■ Using a Multichannel Connection If your D VD player supports multichannel audio formats such as D VD-Audio, and it has a 5.1-channel analog audio output, you can enjoy D VD-Audio playback. Use a multichannel analog audio cable to connect the A V receiv er’ s D VD IN FR ONT L/R, CENTER, SURR L/R, and[...]

30 Connecting the A V receiver —Continued This section shows ho w to connect a VCR for playback so that you can watch videos via the A V receiver. Video Connections • Use an S-V ideo cable to connect the A V receiv er’ s S VIDEO 1 IN jack to a S-V ideo output on your VCR, as shown. OR • Use a composite video cable to connect the A V receiv [...]

31 Connecting the A V receiver —Continued This section explains ho w to connect a VCR for recording from a TV or another VCR. Video Connections • Use an S-V ideo cable to connect the A V receiv er’ s S VIDEO 1 OUT jack to an S-V ideo input on the recording VCR. Use another S-V ideo cable to connect the A V receiver’ s S VIDEO 3 IN jack to a[...]

32 Connecting the A V receiver —Continued Video Connections Y ou only need to use one of the following connection methods. ■ Using Composite Video Use a composite video cable to connect the A V receiver’ s V VIDEO 3 IN jack to a composite video output on your video source, as shown. ■ Using S-Video Use an S-V ideo cable to connect the A V r[...]

33 Connecting the A V receiver —Continued ■ Using Analog Connections If your video source doesn’t ha ve a digital audio output, or you want to record from it, you’ll need to mak e the following analog audio connection. Use an analog audio cable to connect the A V receiver’ s VIDEO 3 IN L/R jacks to the analog audio output on your video so[...]

34 Connecting the A V receiver —Continued ■ Using Optical or Coaxial Connections If you connect to a digital audio input, you’ll need to assign it (see page 42). • Use an optical digital audio cable to connect one of the AV receiv er’ s OPTICAL DIGIT AL IN jacks to the optical output on your CD player , as shown. OR • Use a coaxial digi[...]

35 Connecting the A V receiver —Continued ■ Using Optical or Coaxial Connections (playbac k only) If you connect to a digital audio input, you’ll need to assign it (see page 42). • Use an optical digital audio cable to connect one of the AV receiv er’ s OPTICAL DIGIT AL IN jacks to the optical output on your recorder , as shown. OR • Us[...]

36 Connecting the A V receiver —Continued For the DTR-6.5 The A V receiver’ s PHONO IN is designed for use with a moving magnet (MM) type cartridge. Use an analog audio cable to connect the A V receiver’ s PHONO IN L/R jacks to the audio output on your turn- table, as shown. Notes: • If your turntable has a ground wire, connect it to the AV[...]

37 Connecting the A V receiver —Continued If you want to connect a more po werful power amplifier and use the A V receiver as a preamp, you can connect one to the PRE OUT jacks. In this case, you should con- nect all speakers and the subwoofer to that po wer ampli- fier . Ho wev er , if you hav e a powered subwoofer , connect it to this A V rec[...]

38 Connecting the A V receiver —Continued The A V receiver has AC outlets on its rear panel that can be used to connect the power cords of A V other compo- nents that you intend to use with the A V receiver. These components can then be left turned on so that they turn on and off as and when the A V receiv er is turned on and set to Standby . Cau[...]

39 Fir st Time Setup This chapter explains the settings that you need to make before using the A V receiv er. W ith the supplied speaker setup microphone, the Auto- matic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, their sizes, the distance from each speaker t[...]

40 First Time Setup —Continued 3 Press [Enter]. The automatic speaker setup starts. The test tone, which is somewhat loud, is output by each speaker in turn, mea- sured by the microphone, and the speaker settings set accordingly . The whole process takes about 90 seconds. If any e xtraneous noise is picked up by the microphone, the automatic setu[...]

41 First Time Setup —Continued The A V receiver is configured using onscreen setup menus, which are displayed on the TV that’ s connected to either of the MONITOR OUT jacks. Because the y appear on your TV , they’ re large and clear , making setup a breeze. Settings are divided into tw o groups: Basic Setup and Advanced Setup . When you’ v[...]

42 First Time Setup —Continued Digital Input If you connect a component to a digital input jack, you must assign that jack to an input selector . F or example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector . By default, the OPTICAL IN1 jack is assigned to the D VD input selector , alth[...]

43 First Time Setup —Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector . F or example, if you connect your D VD player to COMPONENT IN 3, you should assign it to the D VD input selector . If you want to output composite and S-V ideo sources from the COMPONENT VIDEO OUT , select V ideo,[...]

44 First Time Setup —Continued Minimum Speaker Impedance (not American models) If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, set the Minimum Speaker Impedance to “4 ohms. ” Note: Before you change this setting, turn down the v olume. Notes: • This procedure can also be performed on the A V receiv[...]

45 First Time Setup —Continued TV Format Setup (not American models) Here you can specify the TV format used in your area. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. 1 Press the [Receiver] button f ol- lowed b y the [Setup] button. The main menu appears onsc[...]

46 First Time Setup —Continued Some of the settings in this section are set automatically by the Automatic Speaker Setup function (see page 39). Here you can check the settings made by the Automatic Speaker Setup function, or set them manually , which is useful if you change one of the connected speakers after using the Automatic Speaker Setup fu[...]

47 First Time Setup —Continued Crosso ver Notes: • If the crossov er frequency is set to a lo w value, and the program material doesn’t contain an y sounds below that frequency , the subwoofer will not output much sound. 6 Use the Up and Down [ ]/[ ] b uttons to select “c. Center , ” and then use the Left and Right [ ]/ [] buttons to sele[...]

48 First Time Setup —Continued Double Bass W ith the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left and right channels to the subwoofer . This function can be set only if the Subwoofer setting in step 4 is set to Y es, and the Front setting in step 5 is set to Large. Notes: • This procedure can also[...]

49 First Time Setup —Continued Notes: • On the DTR-6.5, if the distance between the furthest and nearest speakers is greater than 20 feet (6 meters), corrected values suitable for home theater use will be set automatically . • On the DTR-5.5, the Center and Subwoofer distances can be set up to 5 ft. (1.5 m) more or less than the Front distanc[...]

50 First Time Setup —Continued Speaker Level Calibration Here you can adjust the lev el of each speaker with the b uilt-in test tone so that the v olume of each speaker is the same at the listening position. Notes: • The speakers cannot be calibrated while the output of the A V receiver is muted, while a pair of headphones is connected, or when[...]

51 First Time Setup —Continued Equalizer Setting Here you can adjust the EQ of individual speak ers. The volume of indi vidual speakers can be set on page 50. Notes: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. 1 Press the [Receiver] button f ol- lowed b y the [Setu[...]

52 First Time Setup —Continued If you connect an -compatible Integra MiniDisc recorder or CD recorder to the T APE IN/OUT jacks, for to work properly , you must change this setting. This setting can only be changed on the A V receiver. Changing the T APE/MD/CDR Display 1 Press the [T APE] input selector button so that “T APE” appears on the d[...]

53 Basic Operation This section explains ho w to select the input source (i.e., the A V component that you want to listen to or watch). Selecting the Input Source Standby Zone 2 1 3 On Standby TV Display Muting E x i t G u i d e Prev CH TV CH TV VOL -- / --- Dimmer Tape TV Input Sleep Input I Enter T o p M e n u M e n u S e t u p R e t u r n VOL CH[...]

54 Basic Operation —Continued Y ou can adjust the brightness of the display . Y ou can temporarily mute the output of the A V receiv er. W ith the sleep timer , you can set the A V receiver to auto- matically turn off after a specified period. If you need to cancel the sleep timer , press the [Sleep] button repeatedly until the SLEEP indicator d[...]

55 Basic Operation —Continued Y ou can display various information about the current input source as follows. The following information can typically be displayed for input sources. *If the input signal is analog, no format information is displayed. If the input signal is PCM, the sampling fre- quency is displayed. If the input signal is digital [...]

56 Basic Operation —Continued W ith the built-in tuner you can enjo y AM and FM radio stations. Y ou can store your fav orite stations as presets for quick selection. Listening to the Radio T uning into Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO [...]

57 Basic Operation —Continued Presetting Radio Stations Y ou can store up to 40 of your fav orite radio stations as presets. Selecting Preset Stations Deleting Presets Displaying Radio Inf ormation 1 T une into the station that you want to store as a preset. 2 Press the [Memory] button. The MEMOR Y indicator appears and the preset number flashes[...]

58 Basic Operation —Continued See “ About the Listening Modes” on page 60 for detailed information about the listening modes. Selecting on the A V receiver ■ [Stereo] button This button selects the Stereo listening mode. ■ Listening Mode [ ] [ ] buttons These buttons select all the listening modes that can be used with the current input s[...]

59 Basic Operation —Continued The following table lists all the listening modes and sho ws which modes can be selected for each input signal format. Input signal format Analog, PCM*1 1. In the Pure Audio and Direct listening modes, PCM signals at 32 kHz, 44.1 kHz, and 48 kHz are processed at 64 kHz, 88.2 kHz, and 96 kHz respec- tively. 96 kHz sig[...]

60 Basic Operation —Continued About the Listening Modes W ith its built-in surround-sound decoders and DSP pro- grams, the A V receiver can transform your home listen- ing room into a movie theater or concert hall. If you connect two surround back speakers (i.e., left and right), both will be used for 6.1-channel surround play- back. Direct The s[...]

61 Basic Operation —Continued DTS-ES Matrix This is DTS with an added surround back channel for 6.1 surround sound. Use it to provide 6.1 channel surround playback with program material recorded in DTS 5.1 format. Since DTS 5.1 program material contains surround back channel informa- tion, all channels can be reconstructed for 6.1-channel playbac[...]

62 Ad v anced Operation W ith the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts ev en when listening at low v olume lev els—ideal for watching movies late at night when you don’t w ant to disturb anyone. Notes: • The effect of the Late Night function depends on the Dolby[...]

63 Adv anced Operation —Continued Y ou can adjust the level of indi vidual speakers during playback. These adjustments are temporary and will be cancelled when the A V receiver is set to Standby . Notes: •Y ou cannot use this function while the A V receiver is muted. • Speakers that are set to No or None in the Speaker Configuration cannot b[...]

64 Adv anced Operation —Continued This section explains ho w to record the current input source, how to record one input source while enjo ying another , and how to dub audio onto your video record- ings. Unless you ha ve the full consent of the copyright holder , copyright laws prohibit using y our recordings for anything other than personal enj[...]

65 Adv anced Operation —Continued AV Recording Y ou can record A V input sources to an A V recording component (VCR, etc) connected to the VIDEO 1 OUT or VIDEO 2 OUT . See pages 27–38 for information on connecting components. Recording Separate A V Sources Here you can record audio and video from completely separate sources, allowing you to o v[...]

66 Ad v anced Setup Here are surround-related settings for PCM, Dolby Dig- ital, multichannel, and other input signal formats. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. • The Surround Mode and SurrBack Mode settings can also be changed by using the remote c[...]

67 Adv anced Setup —Continued ■ c. SurrBack Mode This setting determines which surround mode is used for Dolby Digital input signals that don’t contain a Dolby Digital EX flag, or when the b . Dolby EX setting is set to Manual. This setting is una vailable if no surround back speakers are connected. Y ou can select PLIIx Movie (default), PLI[...]

68 Adv anced Setup —Continued Here you can set listening mode-related settings and functions. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. A udio Adjust Functions 1 Press the [Receiver] button f ol- lowed b y the [Setup] button. The main menu appears onscreen.[...]

69 Adv anced Setup —Continued 4-1. Mono ■ a. Output Channel This setting determines which speakers are used to out- put mono audio when the Mono listening mode is used. L/R: Mono audio is output from the front left and right speakers (default). Center: Mono audio is output from the center speaker . ■ b. Academ y (DTR-6.5 only) Early movies ha[...]

70 Adv anced Setup —Continued 4-9. Theater-Dimensional These settings apply to the Theater -Dimensional listen- ing mode. ■ a. Listening Angle W ith this setting, you can specify the angle of the front left and right speakers relati ve to the listening position. Processing for the Theater -Dimensional listening mode is based on this setting. Id[...]

71 Adv anced Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. This section explains the items on the Preference menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] butt[...]

72 Adv anced Setup —Continued 6-1. IntelliV olume W ith this preference, you can set the input lev el for each input source. This is useful if some of your A V compo- nents are louder or quieter than others. While this preference is shown onscreen, you can select each input source and set the lev els while listening to and comparing them. If a co[...]

73 Adv anced Setup —Continued 6-5. Digital Format ■ b. Digital Format This setting does not apply to input selectors not assigned to a digital input jack. W ith this setting, you can set a digital input to DTS, PCM, or Auto. This can be set for each input selector individually . Use the Up and Down [ ]/[ ] buttons to select the input selector t[...]

74 Zone 2 W ith the Zone 2 function, you can enjoy one input source in the main room and a different source in another room. There are two connection methods: using a recei ver/inte- grated amp in Zone 2 or using only a pair of speakers in Zone 2. Using a Receiver/Integrated Amp in Zone 2 W ith this connection method, you can use 7.1 surround sound[...]

75 Zone 2 —Continued To use Zone 2, you must make this setting. It enables the speakers connected to the ZONE 2 SPEAKERS termi- nals so that they produce sound when Zone 2 is used. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. Setting the P owered Zone 2 1 Pres[...]

76 Zone 2 —Continued The ZONE 2 OUT L/R jacks can also be used as pre outs. Setting the Zone 2 Out 1 Press the [Receiver] button f ol- lowed b y the [Setup] button. The main menu appears onscreen. 2 Use the Up and Down [ ]/[ ] buttons to select “1. Initial Setup, ” and then press [Enter]. The Initial Setup menu appears. Pure A Display Muting [...]

77 Zone 2 —Continued Here you can turn on Zone 2, select an input source, and adjust the volume. Note: To control Zone 2 with the remote controller , you must press the [ZONE 2] button first. Notes: • If the Sleep function has been set, the Zone 2 compo- nent will turn off along with the A V receiv er when the specified sleep time expires. T [...]

78 Zone 2 —Continued Using the 12V T rigger When the A V receiver’ s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V TRIGGER IN jack on a connected component, the A V receiver can be configured so that the component is turned on automatically when Zone 2 is used. See page 73 for details. Adjusting the Bass & T reble for Zone2 Y ou can[...]

79 Zone 2 —Continued Using a Multiroom Kit with a Cabinet In the following diagram, an IR recei ver picks up the infrared signals from the remote controller and feeds them to the A V receiver in the cabinet via the connecting block. • On the Remote Setup menu, set the IR IN Position set- ting to “Main” (see page 72). Controlling Out-of-rang[...]

80 Contr olling Other Components Y ou can use the A V Receiver’ s remote controller (RC- 588M/RC-590M/RC-591M) to control your other com- ponents, including those made by other manufacturers. This chapter explains ho w to: • Enter the remote control code for a component that you want to control (e.g., D VD, TV , VCR). • Learn commands directl[...]

81 Controlling Other Components —Continued Resetting Remote Mode Buttons If you’ ve entered another code for one of these b utton and now w ant to return to the default, perform the fol- lowing procedure. By default, some REMO TE MODE b uttons are prepro- grammed with remote control codes for controlling Inte- gra components connected via . Res[...]

82 Controlling Other Components —Continued Remote Control Codes When two or more codes are gi ven, try each one in turn, and choose the one that works best. Depending on the manufacturer and component, the remote controller may not work as expected. D VD (D VD player) Manufacturer Control code Aiwa 5010 Akai 5019 Apex 5015, 5016 CyberHome 5027 De[...]

83 Controlling Other Components —Continued SA T (satellite receiver) Manufacturer Control code Tr istar 4016 Unisat 4013 Universum 4021, 4024 Vo r tec 4017 Wela 4025 Zehnder 4020 Zenith 4032 CBL (cable receiver) Manufacturer Control code ABC 3001, 3002, 3021 Archer 3006 Cabletime 3028, 3032 Cable view 3004 Contec 3009 Eastern 3010 GE 3001, 3002 G[...]

84 Controlling Other Components —Continued VCR Manufacturer Control code RCA 2001, 2002, 2003, 2008, 2010, 2013, 2021, 2023, 2025, 2026, 2027 Realistic 2007, 2008, 2010, 2011, 2012, 2017 Rex 2048 Roadstar 2033, 2043 Runco 2019 Saba 2040, 2048 Saisho 2028, 2041 Salora 2030 Samsung 2008, 2043, 2049 Sansui 2006, 2032 Sanyo 2007, 2008, 2030, 2036 Sav[...]

85 Controlling Other Components —Continued TV Manufacturer Control code Loewe 1014, 1040, 1055 Luxman 1004, 1006 LXI 1001, 1006, 1010, 1014, 1016, 1017, 1034 M Electronic 1035, 1053, 1062, 1063 Magnadyne 1040, 1067, 1068 Magnafon 1067 Magnav ox 1004, 1006, 1008, 1014, 1018, 1020 Marantz 1004, 1006, 1014, 1060 Matsui 1035, 1043, 1048, 1050, 1063, [...]

86 Controlling Other Components —Continued To control another component, point the remote control- ler at it and use the buttons as e xplained below (you must select the appropriate remote control mode first). Controlling a TV Buttons marked with an asterisk can alw ays be used to control a TV re gardless of the currently selected remote control[...]

87 Controlling Other Components —Continued Controlling a VCR The following b uttons control the A V Receiv er . [V OL]: Adjusts the v olume of the A V receiv er. [Muting]: Mutes the A V Receiv er . Controlling a Satellite Receiver The following b uttons control the A V Receiv er . [V OL]: Adjusts the v olume of the A V receiv er. [Muting]: Mutes [...]

88 Controlling Other Components —Continued The A V receiver’ s remote controller can learn the com- mands of other remote controllers simply by pointing them at each other . F or example, by transmitting the Play command from your CD player’ s remote controller , the remote controller can learn it and then transmit the same command when its P[...]

89 Controlling Other Components —Continued W ith the Macro function, you can program the remote controller’ s Macro b uttons to perform a sequence of actions with just one button press. F or example, nor - mally you need to perform the following actions to play a CD: 1. Press the Remote Mode [ [ [ [ R R R R e e e e c c c c e e e e ii i i v v v [...]

90 Tr oub leshooting If you hav e any trouble using the A V receiver, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased this unit. Can’t turn on the A V receiver? • Make sure that the po wer cord is properly plugged into the wall outlet. • Unplug the power cord from the[...]

91 Tr oubleshooting —Continued The subwoof er produces no sound? • When you play source material that contains no infor- mation in the LFE channel, the subwoofer produces no sound. • Make sure the speakers are configured correctly (page 46). There’ s no sound with a certain signal format? • Check the digital audio output setting on the c[...]

92 Tr oubleshooting —Continued Reception is noisy , FM stereo reception is noisy , or the FM STEREO indicator doesn’t appear? • Relocate your antenna. •M ove the A V receiv er away from your TV or com- puter . • Listen to the station in mono (page 56). • When listening to an AM station, operating the remote controller may cause noise. ?[...]

93 Tr oubleshooting —Continued The sound changes when I connect m y head- phones? • When a pair of headphones is connected, the listening mode is set to Stereo, unless it’ s already set to Stereo, Direct, or Pure Audio. When you disconnect the head- phones, the previous listening mode will be resumed. The speaker v olume cannot be set as requ[...]

94 Specifications (DTR-6.5) Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Other Jacks Specifications and features are subject to change without notice. Power Output (2 channels driv en): 100 W + 100 W (8 Ω ,20Hz–20kHz,FTC) 130 W + 130 W (6 Ω [...]

95 Specifications (DTR-5.5) Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs ■ Other Jacks Specifications and features are subject to change without notice. Power Output (2 channels driv en): 85 W + 85 W (8 Ω ,20Hz–20kHz, FTC) 120 W +120 W (6 Ω ,1[...]

96 SN 29343827 (C) Copyright 2004 ONKY O CORPORA TION Japan. All rights reserved. I0407-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Ne[...]