Intel 2047285001R manual

Part No. 2047285001R ESM-2850 Intel Pentium ® M/Celeron ® M ETXexpress Module User’s Manual 2 nd Ed – 22 September 2006[...]

ESM-2850 2 ESM-2850 User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULE S. OPERATION IS SUBJECT TO THE FOLLOWI NG TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CA USE UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN TESTED AN[...]

User’s Manual ESM-2850 User’s Manual 3 Disclaimer Evalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. Evalue Technology a ssumes no responsibility or liability for the use of the describe[...]

ESM-2850 4 ESM-2850 User’s Manual Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your pr oduct documentation. These answers are normally a lot more detailed than the ones we can [...]

User’s Manual ESM-2850 User’s Manual 5 Product Warranty Evalue warrants to you, the orig inal purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any product s which have been repaired or altered by persons other than repair person n[...]

ESM-2850 6 ESM-2850 User’s Manual Contents 1. Getting St arted ............................................................................................................ 9 1.1 Safety Prec autions .................................................................................................... 9 1.2 Packing Li st .............................[...]

User’s Manual ESM-2850 User’s Manual 7 3.5.11 Save & Exit Setup .............................................................................................................. ........ 65 3.5.12 Exit Wit hout Save .............................................................................................................. ......... 66 4 Dri[...]

ESM-2850 8 ESM-2850 User’s Manual 27. Wrong Board In Slot PLEASE RUN EI SA CONFIGURATIO N UTILITY ........................................ 81 28. FLOPPY DISK(S) fail (80) → Unable to reset floppy subs ystem. .................................................. 81 29. FLOPPY DISK(S) fail (40) → Floppy Type di smatch . ...........................[...]

User’s Manual ESM-2850 User’s Manual 9 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel [...]

ESM-2850 10 ESM-2850 User’s Manual 1.3 Document Amendment History Revision Date By Comment 1 st Feb. 2006 Vicky Lin Initial Release 2 nd Sep. 2006 Vicky Lin 1) 2. 4.2 Signals of CN1A modified 2) 2.4.3 Signals of CN1B modified[...]

User’s Manual ESM-2850 User’s Manual 11 1.4 Manual Objectives This manual describes in detail the Evalue Technology ESM-2850 seri es Single Board. We have tried to include as much informati on as possible but we have not duplicated information that is provided in the standard IB M Technical References, unless it proved to be necessary to aid in[...]

ESM-2850 12 ESM-2850 User’s Manual 1.5 System Specifications System CPU Supports 90nm Intel® µFC-PGA 478 / µFC-BGA 4 79 Pentium® M / Celeron® M CPU Note: Available in different CPU speeds by request BIOS Award 512 KB Flash BIOS System Chipset Intel® NQ82915GM GMCH/FW82801FBM ICH6-M System Memory One 200-pin DDR2 SODIMM socket supports up to[...]

User’s Manual ESM-2850 User’s Manual 13 1.6 Architecture Overview 1.6.1 Block Diagram The following block diagram shows the arch itecture and main components of ESM-2850 series. The following sections provide detail info rmation about the functions provided onboard.[...]

ESM-2850 14 ESM-2850 User’s Manual 1.6.2 Intel NQ82915GM and FW82801FMB ICH6-M The Mobile Intel® 915GM Express Chipset for Embedded Computing, consisting of the Intel® 915GM Graphic Memory C ontroller Hub (GMCH) and Inte l® I/O Controller Hub 6-M (ICH6-M), is an optimized integrated graphics solution with a 400 MHz and 533 MHz front-side bus. [...]

User’s Manual ESM-2850 User’s Manual 15 The GMCH contains one 16-lane (x16) PCI Ex press port intended for an external PCI Express Based graphics card. The PCI Express por t is fully compliant to the PCI Express Base Specification revision 1.0a. The x16 port operates at a data rate of 2.5 GB/s while employing 8b/10b encoding. This allows a maxi[...]

ESM-2850 16 ESM-2850 User’s Manual 1.6.3 Ethernet 1.6.3.1 Marvell 88EE8053 Gi gabit Ethernet Controller The single-chip PCI Express based 88E8053 de vice is ideally suited for LAN on motherboard (LOM) and Network Interface Card (NIC) applications. The 88E8053 device is compliant with the PCI Express 1.0a specific ation. Offered in a 9 x 9 mm, 64-[...]

User’s Manual ESM-2850 User’s Manual 17 2. Hardware Configuration[...]

ESM-2850 18 ESM-2850 User’s Manual 2.1 Product Overview[...]

User’s Manual ESM-2850 User’s Manual 19 2.2 Installation Procedure This chapter explains you the instru ctions of how to setup your system. 1. Turn off the power supply. 2. Insert the DIMM module (be careful with t he orientation). 3. Insert all external cables for hard disk, flop py, keyboard, mouse, USB etc. except for flat panel. A CRT monit[...]

ESM-2850 20 ESM-2850 User’s Manual 2.2.1.2 Removing CPU • Unlock the Pentium M processor. • Carefully lift up the existing CPU to remove it from the socket. • Follow the steps of installing a CPU to change to another one. 2.2.2 Main Memory ESM-2850 series provide two 200-pin SO DIMM sockets to support DDR2 533 SDRAM. The total maximum memor[...]

User’s Manual ESM-2850 User’s Manual 21 • Locate the DIMM socket on the board. • Hold two edges of the DIMM module carefu lly. Keep away of touching its connectors. • Align the notch key on the m odule with the rib on the slot. • Firmly press the modules into the socket aut omatically snaps into the mounting notch. Do not force the DIMM[...]

ESM-2850 22 ESM-2850 User’s Manual 2.3 Jumper and Connector List You can configure your board to match the needs of your applic ation by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close[...]

User’s Manual ESM-2850 User’s Manual 23 2.4 Setting Jumpers & Connectors 2.4.1 CPU Frequency Sel ect / Clear CMOS (SW1) CPU Frequency Select (Bit 1 & 2) Auto Detected* 100 MHz Clear CMOS (Bit 3) * Default Protect* Clear CMOS[...]

ESM-2850 24 ESM-2850 User’s Manual 2.4.2 ETX Express Connector 1 (CN1A) (Rear side) Signal PIN PIN Signal GND A1 B1 GND GBE0_MD3- A2 B2 GBE0_ACT# GBE0_MD3+ A3 B3 LPC_FRAME# GBE0_Link100# A4 B4 LPC_AD0 GBE0_Link1000# A5 B5 LPC_A D1 GBE0_MD2- A6 B6 LPC_A D2 GBE0_MD2+ A7 B7 LPC_A D3 GBE0_Link# A8 B8 LPC_DRQ0# GBE0_MD1- A9 B9 LPC_DRQ1# GBE0_MD1+ A10 [...]

User’s Manual ESM-2850 User’s Manual 25 (Rear side) Signal PIN PIN Signal GND A31 B31 GND AC_BITCLK A32 B32 SPKR AC_SDOUT A33 B33 I 2 C_CK NC A34 B34 I 2 C_DAT THRMTRIP# A35 B35 THRM# USB6- A36 B36 USB7- USB6+ A37 B37 USB7- USB_6_7_OC# A38 B38 USB_4_5_OC# USB4- A39 B39 USB5- USB4+ A40 B40 USB5+ GND A41 B41 GND USB2- A42 B42 USB3- USB2+ A43 B43 [...]

ESM-2850 26 ESM-2850 User’s Manual (Rear side) Signal PIN PIN Signal PCIE_TX2+ A61 B61 PCIE_RX2+ PCIE_TX2- A62 B62 PCIE_RX2- GPI1 A63 B63 GPO3 PCIE_TX1+ A64 B64 PCIE_RX1+ PCIC_TX1- A65 B65 PCIE_RX1- GND A66 B66 WAKE0# GPI2 A67 B67 WAKE1# PCIE_TX0+ A68 B68 PCIE_RX0+ PCIE_TX0- A69 B69 PCIE_RX0- GND A70 B70 GND Txout0 A71 B71 E_Txout0 Txout0# A72 B7[...]

User’s Manual ESM-2850 User’s Manual 27 (Rear side) Signal PIN PIN Signal NC A91 B91 VGA_GRN NC A92 B92 VGA_BLU GPO0 A93 B93 VGA_HSYNC NC A94 B94 VGA_VSYNC NC A95 B95 VGA_ I 2 C_CK GND A96 B96 VGA_ I 2 C_DAT +12V A97 B97 Pb +12V A98 B98 Y +12V A99 B99 Pr GND A100 B100 GND +12V A101 B101 +12V +12V A102 B102 +12V +12V A103 B103 +12V +12V A104 B10[...]

ESM-2850 28 ESM-2850 User’s Manual 2.4.2.1 Signal Description – ET X Express Connector 1 (CN1A) 2.4.2.1.1 Audio Signals Signal Signal Description AC_SYNC 48kHz fixed-rate, sample-synchronization signal to the CODEC(s) AC_RST# Reset output to AC97 CODEC, active low. AC_SDIN[0:2] Serial TDM data inputs from up to 3 CODECs. AC_BITCLK 12.228 MHz se[...]

User’s Manual ESM-2850 User’s Manual 29 2.4.2.1.4 Flat Pa nel LVDS Signals Signal Signal Description BIASON Controls panel contrast voltage. DIGON Controls panel digital power. ENBKL# Controls backlight power enable. I 2 C_DAT, I 2 C_CLK I 2 C interface for panel parameter EEPR OM. This EERPOM is mounted on the LVDS receiver. The data in the EE[...]

ESM-2850 30 ESM-2850 User’s Manual 2.4.2.1.6 Miscellaneous Signals Signal Signal Description I 2 C_CK General purpose I 2 C po rt clock output I 2 C_DAT General purpose I 2 C port data I/O line SPKR Output for audio enunciato r - the "sp eaker" in PC-AT systems BIOS_DISABLE# Module BIOS disable input. Pull low to disable module BIO S. U[...]

User’s Manual ESM-2850 User’s Manual 31 2.4.2.1.9 Pow er & System Management Signals Signal Signal Description SUS_S3# Indicates system is in Suspend to RAM state. Active low output. SUS_S4# Indicates system is in Suspend to Di sk state. Active low output. SUS_S5# Indicates syst em is in Soft Off state. Also known as "PS_ON" and c[...]

ESM-2850 32 ESM-2850 User’s Manual 2.4.2.1.11 TV Out Signals Signal Signal Description Pb TVDAC Channel A Output supports the followin g: Composite: CVBS signal Component: Chrominance (Pb) anal og signal. Y TVDAC Channel B Output supports the followin g: S-Video: Luminance analog sign al. Component: Luminance (Y) analog signal. Pr TVDAC Channel C[...]

User’s Manual ESM-2850 User’s Manual 33 2.4.3 ETX Express Connector 2 (CN1B) (Rear side) Signal PIN PIN Signal GND C1 D1 GND IDE_D7 C2 D2 IDE_D5 IDE_D6 C3 D3 IDE_D10 IDE_D3 C4 D4 IDE_D11 IDE_D15 C5 D5 IDE_D12 IDE_D8 C6 D6 IDE_D4 IDE_D9 C7 D7 IDE_D0 IDE_D2 C8 D8 IDE_REQ# IDE_D13 C9 D9 IDE_IOW# IDE_D1 C10 D10 IDE_ACK# GND C11 D11 GND IDE_D14 C12 [...]

ESM-2850 34 ESM-2850 User’s Manual (Rear side) Signal PIN PIN Signal GND C31 D31 GND PCI_AD14 C32 D32 PCI_PAR PCI_CBE1# C33 D33 PCI_SERR# PCI_PERR# C34 D34 PCI_STOP# PCI_LOCK# C35 D35 PCI_TRDY# PCI_DEVSEL# C36 D36 PCI_FRAME# PCI_IRDY# C37 D37 PCI_AD16 PCI_CBE2# C38 D 38 PCI_AD18 PCI_AD17 C39 D39 PCI_AD20 PCI_AD19 C40 D40 PCI_AD22 GND C41 D41 GND [...]

User’s Manual ESM-2850 User’s Manual 35 (Rear side) Signal PIN PIN Signal PEG_RX3+ C61 D61 PEG_TX3+ PEG_RX3- C62 D62 PEG_TX3- NC C63 D63 NC NC C64 D64 NC PEG_RX4+ C65 D65 PEG_TX4+ PEG_RX4- C66 D66 PEG_TX4- NC C67 D67 GND PEG_RX5+ C68 D68 PEG_TX5+ PEG_RX5- C69 D69 PEG_TX5- GND C70 D70 GND PEG_RX6+ C71 D71 PEG_TX6+ PEG_RX6- C72 D72 PEG_TX6- SDVO_[...]

ESM-2850 36 ESM-2850 User’s Manual (Rear side) Signal PIN PIN Signal PEG_RX12+ C91 D91 PEG_TX12+ PEG_RX12- C92 D92 PEG_TX12- GND C93 D93 GND PEG_RX13+ C94 D94 PEG_TX13+ PEG_RX13- C95 D95 PEG_TX13- GND C96 D96 GND NC C97 D97 PEG_ENABLE# PEG_RX14+ C98 D98 PEG_TX14+ PEG_RX14- C99 D99 PEG_TX14- GND C100 D100 GND PEG_RX15+ C101 D101 PEG_TX15+ PEG_RX15[...]

User’s Manual ESM-2850 User’s Manual 37 2.4.3.1 Signal Description – ET X Express Connector 2 (CN1B) 2.4.3.1.1 IDE Signals Signal Signal Description IDE_D[0:15] Bidirectional data to / from IDE device. IDE_A[0:2] Address lines to IDE device. IDE_REQ# IDE Device DMA Request. It is asserted by the IDE device to reque st a data transfer. IDE_IOW[...]

ESM-2850 38 ESM-2850 User’s Manual 2.4.3.1.2 PCI Signals Signal Signal Description PCI_AD[0:31] PCI bus multiplexed addre ss and data lines PCI_PME# PCI Power Management Event: PCI peripherals drive PME# to wake system from low-power states S1–S5. PCI_GNT[0:3]# PCI bus master grant output lines, activ e low. PCI_REQ[0:3]# PCI bus master request[...]

User’s Manual ESM-2850 User’s Manual 39 3 BIOS Setup[...]

ESM-2850 40 ESM-2850 User’s Manual 3.1 Starting Setup The AwardBIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contai ned in the CMOS and begins the process of checking out the system and configuring it. W hen it finishes, the BIOS will seek an operating system on one of the disks and t[...]

User’s Manual ESM-2850 User’s Manual 41 3.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the PageUp and PageDown keys to change entries, pr ess <F1> for help and press <Esc> to quit. The following table provides more detail about how to navigate in the Setup program using the [...]

ESM-2850 42 ESM-2850 User’s Manual • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “ ¾ ” pointer marks all sub menus. 3.3 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To[...]

User’s Manual ESM-2850 User’s Manual 43 3.5 Main Menu Once you enter the AwardBIOS™ CMOS Se tup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Ent er> to accept and enter the sub-menu. Note tha[...]

ESM-2850 44 ESM-2850 User’s Manual 3.5.1 Standard CMOS Features The items in Standard CMOS Se tup Menu are divided into few categories. Each category includes no, one or more than one setup items. Use the arrow ke ys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. 3.5.1.1 Main Me[...]

User’s Manual ESM-2850 User’s Manual 45 Item Options Description Panel Number 640x480 18, 800x600 18, 1024x768 18, 1280x1024 3 6 1400x1050 36, 1600x1200 36 1280x768 18, 1680x1050 3 6 1920x1200 36, 1024x768 18 1024x768 36, 1280x800 18 1280x600 18 Select Panel Resolution that will be displayed depending on the LCD Panel (LFP) TV Standard Off NTSC[...]

ESM-2850 46 ESM-2850 User’s Manual 3.5.2 Advanced BIOS Features This section allows you to configure your system for basic operation. You have the opportunity to select the syst em’s default speed, boot-up seq uence, keyboard operation, shadowing and security. 3.5.2.1 CPU Feature This item allows you to setup t he CPU thermal manage ment functi[...]

User’s Manual ESM-2850 User’s Manual 47 3.5.2.2 Hard Disk Boot Priority This item allows you to select the Hard Disk device boot up priority. Item Description Pri./Sec. Master/Slave Boot up from IDE Primary/Second ary Master/Slave Hard D isk USBHDD 0/1/2 Boot up from 1st/2nd/3rd USB Hard Disk Bootable Add-in Cards Boot up from other Add-In Card[...]

ESM-2850 48 ESM-2850 User’s Manual 3.5.2.7 Swap Floppy Drive While system has two floppy drivers installed, th is item will be affected. This function is to assign physical drive B to logical drive A Item Description Enabled Assign physical drive B to logical drive A Disabled No change 3.5.2.8 Boot Up Floppy Seek Seeks disk drives during boot up.[...]

User’s Manual ESM-2850 User’s Manual 49 Note: To disable security, select PASSW ORD SETTING at Main Menu and then you will be asked to enter password. Do not type anything and just press <Enter>, it will disable security. Once the security is disabled, the system will boot and you can enter Setup freely. 3.5.2.15 APIC Mode The BIOS suppor[...]

ESM-2850 50 ESM-2850 User’s Manual 3.5.3 Advanced Chipset Features This section allows you to configure the system based on the specif ic features of the installed chipset. This chipset manages bus speeds and access to system memory resources, such as DRAM and the external ca che. It also coordinates communications between the conventional ISA bu[...]

User’s Manual ESM-2850 User’s Manual 51 3.5.3.3 DRAM RAS# to CAS# Delay This option allows you to in sert a delay between the RAS ( Row Address Strobe ) and CA S ( Column Address Strobe ) signals. This delay occurs when the SDRAM is written to, read from or refreshed. Naturally, reducing the del ay improves the performance of the SDRAM while in[...]

ESM-2850 52 ESM-2850 User’s Manual 3.5.3.9 Memory Hole At 15M-16M Enabling this feature reserves 15MB to 16M B memory address space to ISA expansion cards that specifically require this setti ng. This makes the me mory from 15MB and up unavailable to the system. Expansion cards can only access memory up to 16MB. The choice: Enable, Disable. 3.5.3[...]

User’s Manual ESM-2850 User’s Manual 53 3.5.3.15 DVMT/FIXED Memory Size This item allows to select DVMT/FIXED memory size. The choices: 64MB, 128MB.[...]

ESM-2850 54 ESM-2850 User’s Manual 3.5.4 Integrated Peripherals Use this menu to specify your se ttings for integrated peripherals. 3.5.4.1 OnChip IDE Device The chipset contains a PCI ID E interface with support for two IDE channels. Select Enabled to activate the primary IDE interface. Sele ct Disabled to deactivate this interface.[...]

User’s Manual ESM-2850 User’s Manual 55 Item Options Description IDE HDD Block Mode Enabled Disabled Block mode is also called block transfer, multiple commands, or multiple sector read/write. If the IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sec[...]

ESM-2850 56 ESM-2850 User’s Manual 3.5.4.2 Onboard Device Item Options Description USB Controller Enabled Disabled This item allows you to set the USB Controller. USB 2.0 Controller Disabled Enabled This item allows you to set the USB 2.0 Controller. USB Keyboard Support Enabled Disabled This item allows you to set the system’s USB keyboard to [...]

User’s Manual ESM-2850 User’s Manual 57 Item Options Description Onboard FDC Controlle r Enabled Disabled Select Enabled if your system has a floppy disk controller (FDC) instal led on the system board and you wish to use it. If you are not going to use FDC or the system h as no floppy drive, select Disabled in this field. Onboard Serial Port 1[...]

ESM-2850 58 ESM-2850 User’s Manual 3.5.5 Power Management Setup The Power Management Setup allows you to conf igure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. 3.5.5.1 ACPI Function This item allows you to enable/disable the ACPI function. The choices: Enable, Disable. 3.5[...]

User’s Manual ESM-2850 User’s Manual 59 3.5.5.5 Video Off Method This determines the manner in which the monitor is blanked. The choices: Blank Screen, V/H SYNC+Blank, DPMS. 3.5.5.6 Video Off In Suspend This determines the manner in which the monitor is blanked. The choice: No, Yes. 3.5.5.7 Suspend Type This item will set the system status to s[...]

ESM-2850 60 ESM-2850 User’s Manual 3.5.5.17 FDD,COM,LPT Port System can be awaked by Floppy Drive, COM or LPT port. The choices: Enabled, Disabled. 3.5.5.18 PCI PIRQ[A-D]# This function will cause the system waking up completely from the power management mode. The choices: Enabled, Disabled.[...]

User’s Manual ESM-2850 User’s Manual 61 3.5.6 PnP / PCI Configuration This section describes configur ing the PCI bus system. PCI, or P ersonal C omputer I nterconnect, is a system which allows I/O dev ices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some ver[...]

ESM-2850 62 ESM-2850 User’s Manual 3.5.6.4 IRQ Resources 3.5.6.4.1 IRQ-3/4/5/7/9/ 10/11/12/14/15 Assigned to This item allows you to determine the IRQ as signed to the ISA bus and is not available to any PCI slot. Legacy ISA for devices compliant wit h the original PC AT bus specification, PCI/ISA PnP for devices complia nt with the Plug and Play[...]

User’s Manual ESM-2850 User’s Manual 63 3.5.8 Load Fail-Safe Defaults Use this menu to load the B IOS default values for the mini mal/stable performance for your system to operate. Press <Y> to load the BIOS default values for the most stable, minimal-performance system operations. 3.5.9 Load Optimized Defaults Use this menu to load the B[...]

ESM-2850 64 ESM-2850 User’s Manual 3.5.10 Set Supervisor / User Passw ord You can set either supervisor or user password, or both of them. Supervisor Password: able to enter/c hange the options of setup menus. User Password: able to enter but no right to change the options of setup menus. Type the password, up to eight characters in length, and p[...]

User’s Manual ESM-2850 User’s Manual 65 PASSWORD DISABLED. When a password has been enabled, you will be prom pted to enter it every time you try to enter Setup. This prevents an unauthorized per son from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password[...]

ESM-2850 66 ESM-2850 User’s Manual 3.5.12 Exit Without Save Abandon all CMOS value changes and exit setup, and the system is restarted after exiting.[...]

User’s Manual ESM-2850 User’s Manual 67 4 Drivers Installation Note : Installation procedures and scr een shots in this section are for your reference and may not be exactly the same as shown on your screen.[...]

ESM-2850 68 ESM-2850 User’s Manual 4.1 Install Chipset Driver (For Intel NQ82915GM) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_ChipsetIntel915GM . Note: The installation procedures a n[...]

User’s Manual ESM-2850 User’s Manual 69 4.2 Install Display Driver (For Intel NQ82915GM) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_VideoIntel82915GM . Note: The installation procedu[...]

ESM-2850 70 ESM-2850 User’s Manual 4.3 Install Audio Driver (For VIA VT1616) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_AudioVIAVT1616. Note: The installation procedures a nd screen sh[...]

User’s Manual ESM-2850 User’s Manual 71 4.4 Install Ethernet Driver (For Marvell 88E8053 Gigabit LAN) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_GigabitMarvell88E8053 . Note: The ins[...]

ESM-2850 72 ESM-2850 User’s Manual Step 6. Select the specific location to Next . Step 9. Repeat the Step 1 ~ Step 3 to confirm the Generic Marvell is ready. Step 7. The wizard runs the setup automatically. Step 8. Click Finish to complete the installation.[...]

User’s Manual ESM-2850 User’s Manual 73 5 Measurement Drawing[...]

ESM-2850 74 ESM-2850 User’s Manual (Unit: mm)[...]

User’s Manual ESM-2850 User’s Manual 75 Appendix A: BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Known Problems[...]

ESM-2850 76 ESM-2850 User’s Manual Appendix B: AWARD BIOS POST Messages[...]

User’s Manual ESM-2850 User’s Manual 77 Overview During the Power On Self-Test (POST), if the BIOS detects an error requiring you to do something to fix, it will either sound a beep code or display a message. If a message is displayed, it will be accompanied by: PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SETUP Post Beep Currently there [...]

ESM-2850 78 ESM-2850 User’s Manual 5. DISPLAY SWITCH IS SET INCORRECTLY Display switch on the motherboard can be set to either monochrome or co lor. This indicates the switch is set to a different setting than indicated in Setup. Determine which setting is correct, and then either turn off the system and change the ju mper, or enter Setup and cha[...]

User’s Manual ESM-2850 User’s Manual 79 12. Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY The non-volatile memory containing EISA configuration information was programmed incorrectly or has become corrupt. Re-run EISA configuration utility to correctly program the memory. Note: When either of these errors appears, the system [...]

ESM-2850 80 ESM-2850 User’s Manual 20. PRESS A KEY TO REBOOT This will be displayed at the bottom screen when an error occurs that requires you to reboot. Press any key and the system will reboot. 21. PRESS F1 TO DISABL E NMI, F2 TO REBOOT When BIOS detects a Non-maskable Interrupt condition during boot, this will allow you to disable the NMI and[...]

User’s Manual ESM-2850 User’s Manual 81 27. Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY The board ID does not match the ID st ored in the EISA non-volatile memory. Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run t he EISA Configur ation Utility. 28. FLOPPY DISK(S) fail (80) → [...]

ESM-2850 82 ESM-2850 User’s Manual 40. POST Codes Please take reference to Phoenix-Award website for the latest post codes. http://www.phoenix.com/en/Customer+Service s/BIOS/AwardBIOS/A ward+Error+Codes.ht m 40.1 Normal POST Code Note: EISA POST codes are typically output to po rt address 300h . ISA POST codes are output to port address 80h. Code[...]

User’s Manual ESM-2850 User’s Manual 83 Code (hex) Name Description 3 Early Superio Init Early Initialized the super IO 4 Reserved 5 Blank video Reset Video controller 6 Reserved 7 Init KBC Keyboard controller init 8 KB test Test the Keyboard 9 Reserved A Mouse Init Initialized the mouse B Onboard Audio init Onboard audio controller initialize [...]

ESM-2850 84 ESM-2850 User’s Manual Code (hex) Name Description 25 Reserved 26 Reserved 27 KBC final Init Final Initial KBC and setup BIOS data area 28 Reserved 29 Initialize Video Interface Read CMOS location 14h to find out type of video in use. Detect and Initialize Video Adapter. 2A Reserved 2B Reserved 2C Reserved 2D Video memory test Test vi[...]

User’s Manual ESM-2850 User’s Manual 85 Code (hex) Name Description 43 Test Stuck 8259's Interrupt Bits Test 8259 Interrupt Functionality Turn off interrupts then verify no interrupt mask registe r is on. Force an interrupt and verify the interrupt occu rred. 44 Reserved 45 Reserved 46 Reserved 47 Set EISA Mode If EISA non-volatile memo ry[...]

ESM-2850 86 ESM-2850 User’s Manual Code (hex) Name Description 5E Reserved 5F Reserved 60 Setup enable Display setup message and enable setu p function s 61 Reserved 62 Reserved 63 Initialize & Install Mouse Detect if mouse is present, init ialize mouse, install interrupt vectors. 64 Reserved 65 PS2 Mouse special Special treatment to PS2 Mous[...]

User’s Manual ESM-2850 User’s Manual 87 Code (hex) Name Description 7D Reserved 7E Reserved 7F POST error check Check POST error and display them and ask for use r intervention 80 Reserved 81 Reserved 82 Security Check Ask password security (op t ional). 83 Write CMOS Write all CMOS values back to RAM and clear screen. 84 Pre-boot Enable Enable[...]

ESM-2850 88 ESM-2850 User’s Manual 40.2 Quick POST Codes Code (hex) Name Description 65 Init onboard device Early Initialized the super IO. Reset Video controller. Keyboard controller init Test the Keyboard Initialized the mouse Onboard aud io controlle r initialize if exist. Check the intergraty of the ROM , BIOS and message Check Flash type and[...]

User’s Manual ESM-2850 User’s Manual 89 Code (hex) Name Description 72 Install FDD Enter setup check and auto11 configuration check up Initialize floppy disk drive controller and any drives. Install FDD and setup BIOS data area parameters 73 Install FDD Initialize hard drive controll er and any drives. IDE device detection and install Initializ[...]

ESM-2850 90 ESM-2850 User’s Manual 40.3 S4 POST Codes Code (hex) Name Description 5A Early Chipset Init Early Initialized the super IO . Reset Video controller . Keyboard controller init . Test the Keyboard Initilized the mouse 5B Cmos Check Check Cmos Circuitry and reset CMOS 5C Chipset default Prog Program the chipset registers with CM OS value[...]

User’s Manual ESM-2850 User’s Manual 91 40.4 BootBlock POST Codes Code (hex) Name Description 1 Base memory test Clear base memory area ( 0000:0000--9000:ffffh) 5 KB init Initialized KBC 12 Install interrupt vectors Insta ll int. vector (0-77), and initialized 00-1fh to their proper place 0D Init Video Video initializing 41 Init FDD Scan floppy[...]