Intel I815E manual

I815E Socket 370 Intel 815E Little Board USER ’ S MANUAL Version 1.1[...]

ii I815E User ’ s Manual Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Celeron are reg istered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademar[...]

I815E User ’ s Manual iii Table of Contents Introduction ............................................................... 1 Product Description .......................................................... 1 Checklist ........................................................................... 2 Specifications .........................................[...]

iv I815E User ’ s Manual A picture of the I815E Embedded Board[...]

INTRODUCTION I815E User ’ s Manual 1 Introduction Product Description I815E is a high - performance flexible embedded board based on the Intel 815E chipset th at contains the Graphics and Memory Controller Hub (GMCH), the I/O Controller Hub (ICH2) and the Firmware Hub (FWH). It supports 66/100/133MHz system bus, up to 1.4GHz CPU speed, integrated[...]

INTRODUCTION 2 I815E User ’ s Manual Checklist Your I815E package should include the items listed below. • The I815E Embedded Little Board • This User’s M anual • 1 IDE Ribbon Cable • 1 Floppy Ribbon Connector • 1 CD containing the following: • Chipset Drivers • Flash Memory Utility[...]

INTRODUCTION I815E User ’ s Manual 3 Specifications Processor Supported Socket 370 for Intel Celeron / Pentium III (FC - PGA), 533MHz~1.4GHz, 66/100/133MHz Bus Spee d Chipset Intel 815E Chipset GMCH: 82815 544 - PIN BGA ICH2: 82801BA 360 - PIN BGA FWH BIOS Award BIOS; supports ACPI System Memory 1x DIMM socket supports up to 256MB capacity PC100/[...]

INTRODUCTION 4 I815E User ’ s Manual Board Dimensions[...]

INSTALLATIONS I815E User ’ s Manual 5 Installations This section provides information on how to use the jumpers and connectors on the I815E in order to set up a workable system. The topics covered are: Installing the CPU ............................................................. 6 Installing the Memory (DIMM) ..................................[...]

INSTALLATIONS 6 I815E User ’ s Manual Installing the CPU The I815E board supports a Soc ket 370 processor socket for Intel Pentium III and Celeron processors. The Socket 370 processor socket comes with a lever to secure the processor. Raise this lever to about a 90 ° angle to allow the insertion of the processor. Place the processor into the soc[...]

INSTALLATIONS I815E User ’ s Manual 7 Installing the Memory (DIMM) The I815E board supports one 168 - pin DIMM socket for a maximum total memory of 256MB in SDRAM type. The memory module capacities supported are 32MB, 64MB, 128MB and 256MB. Installing a nd Removing DIMMs To install the DIMM, locate the memory slot on the board and perform the fol[...]

INSTALLATIONS 8 I815E User ’ s Manual Setting the Jumpers Jumpers are used on I815E to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on I815E and their respective functions. Jumper Locatio ns on[...]

INSTALLATIONS I815E User ’ s Manual 9 Jumper Locations on I815E Jumpers: JP2: Clear CMOS Contents JP5, JP7, JP8: RS232/422/485 (COM2) Selection J P6: BIOS Write Protect JP9, JP10: CPU Overclocking[...]

INSTALLATIONS 10 I815E User ’ s Manual Configuring the CPU Frequency The I815E board does not provide DIP switches to configure the processor speed (CPU frequency). However, the processor speed can be configured inside the BIOS Setup. Refer to the BIOS Setup section in this manual on how to change the processor speed. JP2: Clear CMOS Contents Use[...]

INSTALLATIONS I815E User ’ s Manual 11 JP6: BIOS Write Protect JP6 can be used to protect the BIOS from being overwritten due to accidental modification or virus attacks. JP6 Write Protect Disabled Enabled JP9, JP10: CPU Overclocking Use JP9 and JP10 2 - pin jumpers when overclocking the CPU bus speed from 66MHz to 100MHz or 100MHz to 133MHz. Ref[...]

INSTALLATIONS 12 I815E User ’ s Manual [ Connectors on I815E The connectors on I815E allows you to connect external devices such as keyboard, floppy disk dr ives, hard disk drives, printers, etc. The following table lists the connectors on I815E and their respective functions. Connector Locations on I815E .........................................[...]

INSTALLATIONS I815E User ’ s Manual 13 Connector Locations on I815E Connectors: IDE1, IDE2: Primary and Secondary IDE Connectors FDD1: Floppy Drive Connector J2: System Function Connector FAN1: CPU Fan Power Connector FAN2, FAN3: System Fan Power Connectors J1, J3: Line - out and Microphone connectors J4, J5: CD In Connectors J6: Secondary RJ45 C[...]

INSTALLATIONS 14 I815E User ’ s Manual IDE1, IDE2: Primary and Secondary IDE Con nectors Signal Name Pin # Pin # Signal Name Reset IDE 1 2 Ground Host data 7 3 4 Host data 8 Host data 6 5 6 Host data 9 Host data 5 7 8 Host data 10 Host data 4 9 10 Host data 11 Host data 3 11 12 Host data 12 Hos t data 2 13 14 Host data 13 Host data 1 15 16 Host d[...]

INSTALLATIONS I815E User ’ s Manual 15 FDD1: Floppy Drive Connector FDD1 is a 34 - pin header and will support up to 2.88MB floppy drives. Signal Name Pin # Pin # Signal Name Ground 1 2 RM/LC Ground 3 4 No connect Ground 5 6 No connect Groun d 7 8 Index Ground 9 10 Motor enable 0 Ground 11 12 Drive select 1 Ground 13 14 Drive select 0 Ground 15 1[...]

INSTALLATIONS 16 I815E User ’ s Manual Speaker: Pins 1 - 4 This connector provides an interface to a speaker for audio tone generation. An 8 - ohm speaker is recommended. Pin # Signal Name 1 Speaker out 2 No connect 3 G round 4 +5V Power LED: Pins 11 - 15 The power LED indicates the status of the main power switch. Pin # Signal Name 11 Power LED [...]

INSTALLATIONS I815E User ’ s Manual 17 Turbo LED Connector: Pins 8 and 18 There is no turbo/deturbo function on the board. The Turbo LED on the control panel will always be On when attached to this connector. Pin # Signal Name 8 5V 18 Ground Reset Switch: Pin s 9 and 19 The reset switch allows the user to reset the system without turning the main[...]

INSTALLATIONS 18 I815E User ’ s Manual FAN2, FAN3: System Fan Power Connectors FAN2 and FAN3 are 3 - pin headers for the system fans. The fans must su pport 12V. Pin # Signal Name 1 Ground 2 +12V 3 2 1 3 Rotation detection J1, J3: Line - out and Microphone connectors J1 ad J3 are connectors for Line out and Microphone jacks. J4, J5: CD In Connect[...]

INSTALLATIONS I815E User ’ s Manual 19 J7: USB3/USB4 Connector J7 is the onboard USB pin - header that supports an optional USB connector cable with two ports for USB3 and USB4. Pin # Signal Name 1 8 Vcc 2 7 USB - 3 6 USB+ 4 5 Ground J8: VGA CRT Co nnector J8 is a DB - 15 VGA connector located beside the COM1 port. The following table shows the p[...]

INSTALLATIONS 20 I815E User ’ s Manual J10: Parallel Port Connector J10 is a DB - 25 external connector situated on top of the VGA and serial ports. The following table describes the pin - out assignments of this connect or. Signal Name Pin # Pin # Signal Name Line printer strobe 1 14 AutoFeed PD0, parallel data 0 2 15 Error PD1, parallel data 1 [...]

INSTALLATIONS I815E User ’ s Manual 21 J15, J12: COM1 / COM2 Serial Ports J15 (COM1) is a DB - 9 connector, while J12 (COM2) is a 10 - pin header. Refer to the table below for their pin assignments. CO M1 COM2 Signal Name Pin # Pin # Signal Name DCD, Data carrier detect 1 6 DSR, Data set ready RXD, Receive data 2 7 RTS, Request to send TXD, Trans[...]

INSTALLATIONS 22 I815E User ’ s Manual J16: USB and Primary RJ45 Connectors J16 consists of the primary RJ - 45 connector (top) and two stacked USB ports. Refer to the section below for their respective pin assignments. Pin # Signal Name 1 Vcc 2 USB - 3 USB+ USB1 USB2 4 Ground J17: Smart Card Reader Interface J17 is a 14 - pin header that provide[...]

INSTALLATIONS I815E User ’ s Manual 23 J19: IrDA Connector J19 is used for an optional IrDA connector for wireless communication. Pin # Signal Name 1 +5V 2 No connect 3 Ir RX 4 Ground +5V IRRX IRTX N.C. GND 5 Ir TX J21: External Keyboard Connector Signal Name Pin # Pin # Signal Name Vcc 1 4 KBCLK_OUT KBDAT_OUT 2 5 KBCLK_IN KBDAT_IN 3 6 GND J22: G[...]

INSTALLATIONS 24 I815E User ’ s Manual J24, J25: PS/2 Mouse and PS/2 Keyboa rd Connectors PS/2 Mouse PS/2 Keyboard Signal Name Keyboard Mouse Signal Name Keyboard data 1 1 Mouse data N.C. 2 2 N.C. GND 3 3 GND 5V 4 4 5V Keyboard clock 5 5 Mouse clock N.C. 6 6 N.C. J26: ATX Power Supply Connector J26 is a 20 - pin A TX power supply connector. Refer[...]

BIOS SETUP I815E User ’ s Manual 25 BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the board. The topics covered in this chapter are as follows: BIOS Introd uction ............................................................................ 26 BIOS Setup .......................................[...]

BIOS SETUP 26 I815E User ’ s Manual BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel Pentium II/III processors. The BIOS provides critical low - level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection a[...]

BIOS SETUP I815E User ’ s Manual 27 CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail - Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Passwor d Power Management Setup Set User Password PnP/PCI Conf[...]

BIOS SETUP 28 I815E User ’ s Manual Standard CMOS Setup “S tandard CMOS Setup” choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the board is already installed in a working system, you will not need to select this option. You will need to run the Standard CMO[...]

BIOS SETUP I815E User ’ s Manual 29 Time The time format is: Hour : 00 to 23 Minute : 00 to 59 Second : 00 to 59 To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or +/ - keys to set the current time. IDE Primary HDDs / IDE Secon dary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels f[...]

BIOS SETUP 30 I815E User ’ s Manual Video This field selects the type of video di splay card installed in your system. You can choose the following video display cards: EGA/VGA For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) CGA 40 Power up in 40 column mode. CGA 80 Power up in 80 column mode. MONO For Hercules or MDA adapters. Halt O[...]

BIOS SETUP I815E User ’ s Manual 31 Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system f eatures according to your preference. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Advanced BIOS Features Virus Warning Disabled ITEM HELP CPU Internal Cache Enabled Menu [...]

BIOS SETUP 32 I815E User ’ s Manual CPU L2 Cache ECC Checking This field enables or disables the ECC (Error Correction Checking) checking of the CPU level - 2 cache. The default setting is Enabled . Processor Numb er Feature When enabled, this feature allows external systems to detect the processor number/type of the CPU. Quick Power On Self Test[...]

BIOS SETUP I815E User ’ s Manual 33 Typematic Rate Setting When disabled, continually holding down a key on your keyboard will generate only one instance. When enabled, you can set the two typematic controls l isted next. By default, this field is set to Disabled. Typematic Rate (Chars/Sec) When the typematic rate is enabled, the system registers[...]

BIOS SETUP 34 I815E User ’ s Manual Advanced Chipset Features This Setup menu controls the configuration of the chipset. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Advanced Chipset Features SDRAM CAS Latency Time 3 IT EM HELP SDRAM Cycle Time Tras/Trc Auto Menu Level SDRAM RAS - to - CAS Delay Auto SDRAM RAS Precharge Time Aut[...]

BIOS SETUP I815E User ’ s Manual 35 Video BIOS Cacheable The Setting Enabled allows caching of the video BIOS ROM at C000 0h - F7FFFh, resulting in better video performance. However, if any program writes to this memory area, a system error may result. CPU Latency Timer The default setting for the CPU Latency Timer is Enabled . Delayed Transactio[...]

BIOS SETUP 36 I815E User ’ s Manual Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Integrated Peripherals On - Chip Primary PCI IDE Enabled ITEM HELP On - Chip Secondary PCI IDE Enabled Menu Level IDE Primary Master PIO Aut[...]

BIOS SETUP I815E User ’ s Manual 37 IDE Primary/Secondary Master/Slave UDMA These fields allow your system to improve disk I/O throughput to 33Mb/sec with the Ultra DMA/33 feature. The options are Auto and Disabled . USB Controller The options for this field are Enabled and Disabled . By default, this field is set to Enabled . USB Keyboard Suppor[...]

BIOS SETUP 38 I815E User ’ s Manual Onboard Serial/Parallel Port These fields allow you to select the onboard serial and parallel ports and their addresses. The default values for these ports are: Serial Port 1 3F8H/IRQ4 Serial Port 2 2F8H/IRQ3 Parallel Port 378H/IRQ 7 UART Mode Select This field determines the UART 2 mode in your computer. The d[...]

BIOS SETUP I815E User ’ s Manual 39 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Power Management Setup ACPI Function Enabled ITEM HELP ACPI Suspend Type (S1 (POS) Menu Level Power Management User Define Video Off Method DPMS [...]

BIOS SETUP 40 I815E User ’ s Manual Video Off Method This field defines the Video Off features. There are three options. V/H SYNC + Blank Default setting, blank the screen and turn off vertical and horizontal scanning. DPMS Allows the BIOS to control the video display card if it supports the DPMS feature. Blank Screen This option only writes blan[...]

BIOS SETUP I815E User ’ s Manual 41 Resume by Alarm This field enables or disables the resumption of the system operation. When enabled, the user is allowed to set the Date and Time . Reload Global Timer Events The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can prevent the system from entering a power saving mode or can awaken th[...]

BIOS SETUP 42 I815E User ’ s Manual PNP/PCI Configurations This option configures the PCI bus system. All PCI bus systems on the system use INT#, thus all inst alled PCI cards must be set to this value. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software PnP/PCI Configurations Reset Configuration Data Disabled ITEM HELP Resources Contr[...]

BIOS SETUP I815E User ’ s Manual 43 PC Health Status This section shows the parameters in determining t he PC Health Status. These parameters include temperatures, fan speeds and voltages. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software PC Health Status Shutdown Temperature Disabled ITEM HELP Vcore (V) 1.63V +1.8(V) 1.79V VCC3(V) 3[...]

BIOS SETUP 44 I815E User ’ s Manual Frequency/Voltage Control This section shows the user how to configure the processor frequency. CMOS Setup Utility – Copyright © 1984 - 2001 Award Software Frequency/Voltage Control Auto Detect DIMM/PCI Clk Disabled ITEM HELP Spread Spectrum Disabled Host CPU/PCI Clock Default CPU Clock Ratio X 3 Menu Level [...]

BIOS SETUP I815E User ’ s Manual 45 Load Fail - Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM. These default settings are non - optimal a nd disable all high - performance features. Load Setup Defaults This option allows you to load the default values to your system configuratio[...]

BIOS SETUP 46 I815E User ’ s Manual This page is in tentionally left blank.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 47 Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The software and drivers are included with the board. If you find the items mi ssing, please contact the vendor where you made the purchase. The cont[...]

DRIVERS INSTALLATION 48 I815E User ’ s Manual I815E Windows 98 Drivers Installation Intel Software Installation Utility The Intel Chipset Software Installation Utility will enable Plug & Play I N F support for Intel chipset components. Follow the instructions below to complete the installation under Windows 98. 1. Insert the CD that comes wit[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 49 Intel Ultra ATA Storage Driver Follow the steps below to install Intel Ultra ATA Storage Driver with the InstallShield Wizard under Windows 98. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click Intel Ultra ATA IDE Dr[...]

DRIVERS INSTALLATION 50 I815E User ’ s Manual 6. You are now asked to select a program folder. Click Next to accept the default program folder or enter the folder name you prefer. 7. The InstallShield Wizard has completed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 51 Intel 815E Chipset VGA Driver Follow the steps below to install Intel 81x Family Chipset Graphics Driv er Software under Windows 98. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click Intel 815x Chipset Graphics Drive[...]

DRIVERS INSTALLATION 52 I815E User ’ s Manual SigmaTel AC97 Audio Drivers Follow the steps below to install SigmaTel AC97 Audio Drivers on your system under Windows 98. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 81 5(E) Driver. 2. In the Intel 815 Driver screen, click SigmaTel AC97 Audio Driver. 3. The Welcome [...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 53 6. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect. 7. After the system has restarted, a screen would appear saying it was able to find the device “Intel AC’97 Audio Controller.” Click Next to continue. 8. Now click Select to[...]

DRIVERS INSTALLATION 54 I815E User ’ s Manual I815E Windows NT 4.0 Drivers Installation Intel Ultra ATA Storage Driver Follow the steps below to install Intel Ultra ATA Storage Driver with the I nstallShield Wizard under Windows NT 4.0. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 8[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 55 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. You are now required to Select the folder where Setup will install fi les. Click Next to accept the default folder or click Browse to configure the location.[...]

DRIVERS INSTALLATION 56 I815E User ’ s Manual 6. You are now asked to select a program folder. Click Next to accept the default program folder or enter the folder name you prefer. 7. The InstallShield Wiz ard has completed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 57 Intel 815E Chipset VGA Driver Follow the steps below to install Intel 81x Family Chipset Graphics Driver Software under Windows NT 4.0. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click Intel 81x Chipset Graphics Dri[...]

DRIVERS INSTALLATION 58 I815E User ’ s Manual 4. Click Yes to accept the software license agreement and proceed with the installation process. 5. The Setup program has now completed installation. Click Finish for the computer to restart and changes to ta ke effect.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 59 SigmaTel AC97 Audio Drivers Follow the steps below to install SigmaTel AC97 Audio Drivers on your system under Windows NT 4.0. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click SigmaTel AC97 Audio Driver. 3. The Welc[...]

DRIVERS INSTALLATION 60 I815E User ’ s Manual 4. Click Yes to accept the software license agreement and proceed with the installation proc ess. 5. Select Install and click Next to install SigmaTel AC97 Audio Drivers on your system.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 61 6. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect. 7. After the system has r estarted, a screen would appear showing some installation information. Restart the system when prompted to complete the audio driver installation.[...]

DRIVERS INSTALLATION 62 I815E User ’ s Manual I815E Windows 2000 Drivers Installation Intel Software Installation Utility The Intel Chipset Software Installation Utility will enable Plug & Play I N F support for Intel chipset components. Follow the instructions below to complete the installation under Windows 2000. 1. Insert the CD that comes[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 63 Intel Ultra ATA Storage Driver Follow the steps below to install Intel Ultra ATA Storage Driver with the InstallShield Wizard under Windows 98. 1. Insert the CD that comes with the board. In the initi al scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click Intel Ultra ATA IDE D[...]

DRIVERS INSTALLATION 64 I815E User ’ s Manual 6. You are now a sked to select a program folder. Click Next to accept the default program folder or enter the folder name you prefer. 7. The InstallShield Wizard has completed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 65 Int el 815E Chipset VGA Driver Follow the steps below to install Intel 81x Family Chipset Graphics Driver Software under Windows 2000. 1. Insert the CD that comes with the board. In the initial scrren, click Intel 815(E) Driver. 2. In the Intel 815 Driver screen, click Intel 815x Chipset Graphics Dri[...]

DRIVERS INSTALLATION 66 I815E User ’ s Manual SigmaTel AC97 Audio Drivers Follow the steps below to install SigmaTel AC97 Audio Drivers on your syste m under Windows 2000. 1. Insert the CD that comes with the board. The CD will autorun and show an initial screen. Click Intel 815(E) Driver. 2. Click SigmaTel AC97 Audio Driver. 3. The Welcome scree[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 67 6. A window appears indica ting that the software to be installed does not contain a Microsoft digital signature. Click Yes to continue the installation process. 7. The Setup program has now completed installation. Click Finish for the computer to restart and changes to take effect.[...]

DRIVERS INSTALLATION 68 I815E User ’ s Manual Intel 82559 LAN Drivers Installation Introduction Intel 82559 a 32 - bit 10/100MBps Ethernet controller for PCI local bus - compliant PCs. It supports bus mastering architecture, and auto - negotiation feature that can be used for both 10Mbps and 100Mbps connection. Making Floppy Disks for NetWare and[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 69 Installing LAN Drivers for Windows 95 Follow these steps to install the Intel 82559 LAN/Ethernet driver for Windows 95: 1. From the Control Panel , double - click the System icon. 2. Click the Device Man ager tab. 3. Double - click Other Devices (question mark icon) in the list area. 4. Double - clic[...]

DRIVERS INSTALLATION 70 I815E User ’ s Manual Installing LAN Drivers for Windows NT Follow the steps below to install the PCI Ethernet/LAN drivers Windows NT 4.0. 1. Under the Windows NT 4.0 environment, click Start à Control Panel . Double click Network à Adapters à Add . 2. Select “ Have disk … ” and insert the floppy diskette containi[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 71 TV Out Drivers Installation Introduction The I815E 5.25” embedded board supports the optional TV out function with the optional IB742 TV Out Daughter Card. After you have installed the IBD742 daughter card onto I815E , install the TV - Out drivers by doing the following procedure. 1. Insert the dis[...]

DRIVERS INSTALLATION 72 I815E User ’ s Manual 2. Click Next to continue with the Setup program. 3. Click Next to begin copying the program files.[...]

DRIVERS INSTALLATI ON I815E User ’ s Manual 73 4. After file copying is finished, click Finish to restart the computer and for changes to take effect.[...]

DRIVERS INSTALLATION 74 I815E User ’ s Manual This page was intentionally left blank.[...]

APPENDIX I815E User ’ s Manual 75 Appendix A. I/O Port Address Map B. Interrupt Request Lines (IRQ) A. I/O Port Address Map Each periph eral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Description 000h - 01Fh DMA C[...]

APPENDIX 76 I815E User ’ s Manual B. Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows th e IRQ used by the devices on board. Level Function IRQ0 System Timer Output IRQ1 Keyboard IRQ2 Interrupt Cascade IRQ3 Serial Port #2 IRQ4 Serial Port #1 IRQ5 Reserve[...]