Intel IP-4MTS6B manual

IP-4MTS6B (IP-4GMS6F) Series (Embedded Board) I NSTALLATION G UIDE Installation Guide Revision A1 600700246BA10[...]

[...]

i COPYRIGHT © All rights reserved. The information contained in this guide h as been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the informat ion contai ned herein. While every precaution has been taken in the prepa ration of this guide, the Manufacturer assumes no responsibility for errors or omi[...]

ii C ONTENTS S ECTION 1 I NTRODUCTION 1 1.1 Unpacking IP-4MTS6B / 4GMS6F Series 1 1.2 Description 3 1.3 Features 3 1.3.1 Graphic & Ethernet 3 1.3.2 Ultra ATA/66/100 4 1.3.3 Hardware Monitoring 4 1.3.4 I/O Shield Connector 4 1.3.5 Power-On/Off 5 1.3.6 IP-4MTS6B / IP-4GMS6F Series Overview 5 1.3.7 System Block Diagram 6 1.4 Specifications 7 1.5 M[...]

iii C ONTENTS S ECTION 3 A WA RD BIOS S ETUP 33 3.1 BIOS Instructions 33 3.2 Main Menu 34 3.3 Standard CMOS Features 36 3.4 IDE Adapters 38 3.5 Advanced BIOS Features 40 3.6 Advanced Chipset Features 44 3.7 Integrated Peripherals 47 3.8 Power Management Setup 52 3.9 PnP/PCI Configurations 55 3.10 PC Health Status 57 3.11 Frequency/Voltage Control 5[...]

iv[...]

1 I NTRODUCTION 1.1 Unpacking IP-4MTS6B / 4GMS6F Series 1. Take out the IP-4MTS6B / 4GMS6F se ries unit from the carton box, check if the unit is properly secure in the plastic bag. 2. Check the contents of the carton box: ¡ Industrial board (IP-4MTS6B) ¡ Industrial board (IP-4GMS 6F) ¡ ATA-66/100 HDD ribbo n cable ¡ Floppy ribbon cable ¡ Inst[...]

Introduction 2 ¡ External K/B & M/S cable ¡ Driver CD (6-pins to 6-pins) ¡ Heat sink with fan ¡ Heat sink without fan (for IP-4MTS6B series) (for IP-4GMS6F series) ¡ I/O Shield[...]

Introduction 3 1.2 Description The IP-4MTS6B series combines the high performa nce and exceptional value of Intel ® 855GME chipset with a full-featured, new gen eration, industrial board. The Intel ® advanced 855GME chipset suppo rt socket 479-pins Intel ® Pentium ® M / Celeron ® M processor of 1.3GHz and up to 2.0GHz (Dothan™ Core), that me[...]

Introduction 4 ¡ Memory: - DDR SDRAM 200/266/333 - 1 x 184-pins DIMM socket, with support ECC - 1.0GB Max. ¡ IO Connectivity - ICH4: - 6 Hi-Speed USB2.0 ports - AC97 Audio Codec 1.3.2 Ultra ATA/66/100 The ICH4 provides two channel Ult ra AT A/66/100 Bus Master IDE controller, that support Ultra ATA/ 66/100 protocol s, perfect for such demanding a[...]

Introduction 5 1.3.5 Power-On/Off (Remote) The board has a single 20 -pins connector for ATX powe r supplies. For ATX power supplies that support the Re mote On/Off feature, this should be connected to the systems front panel for system Power On/Off button. The systems power On/Off button should be a momentary button that is normally open. The boar[...]

Introduction 6 1.3.7 System Block Diagram So ck et 47 9 -p in s for Intel Pe ntium M Cl oc k VRM DA TA CTR L ADDR GMCH (855 GME) 7 3 2 M i c r o F C B G A ICH4 421 BGA DDR266/333 X1 DVI / CRT Devi c e Sup er I/O W83627HF ATA 1 0 0 USB2. 0 IDE Primary IDE Second ary USB Por t 1/2 USB Por t 3/4 FW H Keyboard Mouse COM Port LPT Po rt Floppy PCI BUS PC[...]

Introduction 7 1.4 Specifications ¡ Processor: (IP-4MTS6B) - Support socket 479 Intel ® Pentium ® M with 1MB L2 cache p ro ce s sor, Speed at 1.1GHz ~ 1.7GHz (Banias™ core) - Support socket 479 Intel ® Pentium ® M with 2MB L2 cache p ro ce s sor, Speed at 1.5GHz ~ 2.0GHz (Dothan™ core) - System bus frequency at 400 MHz FSB - IP-4GMS6F onbo[...]

Introduction 8 ¡ Rear I/O Connectors: - PS/2 mouse and PS/2 style keyboard - D-Sub 25-pins pri nter po rt connector D-Sub 9-pins COM1 serial port connector for RS-232 D-Sub 15-pins VGA c onnector - RJ-45 Ethernet (LAN1) and 2 x USB2.0 (USB 0/1) conne ctors - RJ-45 Ethernet (LAN2) and 2 x USB2.0 (USB 2/3) conne ctors ¡ Internal I/O Connectors (pin[...]

9 I NSTALLATIONS 2.1 System Installation 2.1.1 CPU Installation (IP-4MTS6B series) Carefully follow the st eps below in order to install the CPU: 1. Check and confirm that you are goi ng to install correctly CPU type and pin numbers (figure 3). 2. Take the screwd river an d releas ing screw-nut of the socket 479. 3. Rotate mark of screw-nut to face[...]

Installations 10 Removing a CPU: 1. Before removi ng the CP U, turn o ff the IP-4MTS6B series power; then wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools do wn. 2. Rotate mark of screw-nut to face the “OPEN”. 3. To remove the CPU. Note: The CPU and the heat radiation plate a re hot. They may cause b[...]

Installations 11 2.1.3 Memory Module Installation Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIMMs have 184-pins and two notches, that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree a ngle and pre ssi ng st raight d own (f[...]

Installations 12 Carefully follow the steps below in order to install the DIMMs: 1. To avoid generating static elec tricity and damaging the DIMM, ground yourself by touching a grounded metal surface or using a ground scrap before you touch the DIMM. 2. Do not touch the connector of the DIMM. Dirt residue may cause a malfunction. 3. Hold the DIMM w[...]

Installations 13 2.1.4 Setting Jumpers There are jumpers on the Embedded Board of the IP-4MTS6B series. You can set the jumpers to make the necessary op erations. Figure 7: Jumper Connec tor For any three-pins jumpers (Figure 7), the jumper setting is 1-2 when the jumper connects pins 1 and 2. The setting is 2-3 whe n pin s 2 and 3 are connected an[...]

Installations 14 2.2 Board Layout IP-4MTS6B Jumper & Connector Location CN6 CN1 1 CN9 CN13 CN10 CN8 CN5 CN2 CN7 CN1 CN14 JP5 CN17 CN19 CN16 CN20 CN15 CN21 CN18 JP4 CN12 JP1 JP2 CN4 93004 SYSTEM-F AN CPU-FAN A UTO POWER ON EXT . KB/MS KB/MS COM1 VGA USB0/1 USB2/3 LAN1 LAN 2 LAN 1-L ED LAN 2-L ED IR-CONN USB4/5 DIMM1 BA TT1 LINE-O UT CD-IN IDE2 I[...]

Installations 15 2.3 Jumper Setting Table for Jumper Location Description: Use the information in the followi ng table to change the jump ers. Jumpers Functions JP4 Clear CMOS setting select JP5 Auto power on setting sel ect JP6 LCD po wer sett ing select[...]

Installations 16 In order to set up the corre ct configuration, here is the description about how to set the jumpers to enabl e/disable or change f unctions. All jumpers’ location please refer to jumper location diagram.  Clear CMOS setting select: JP4 Function JP4 Normal (Default) 1-2 Clear CMOS 2-3 y Location:  Auto power on setting selec[...]

Installations 17  LCD power setting sel ect: JP6 Function JP4 3.3V (Default) 1-2 5V 2-3 y Location:[...]

Installations 18 2.4 Connector’s Description IP-4MTS6B Co nnector Loc ation CN6 CN1 1 CN9 CN13 CN10 CN8 CN5 CN2 CN7 CN1 CN14 JP5 CN17 CN19 CN16 CN20 CN15 CN21 CN18 JP4 CN12 JP1 JP2 CN4 93004 SYSTEM-F AN CPU-FAN A UTO POWER ON EXT . KB/MS KB/MS COM1 VGA USB0/1 USB2/3 LAN1 LAN 2 LAN 1-L ED LAN 2-L ED IR-CONN USB4/5 DIMM1 BA TT1 LINE-O UT CD-IN IDE2[...]

Installations 19 Table for Connector’s Location Description: Use the information in the following table to change the co nne ctor. Connectors Functions CN1 CRT VGA port connector CN2 COM1 RS-232 serial port connector CN3 Parallel port connector CN4 IrDA connector CN5 PS/2 keyboard & mouse connectors CN6 USB 2/3 & Gigabit Ethernet RJ-45 (L[...]

Installations 20  CRT VGA port connect or (D -SUB 15-pins femal e): CN1 Pin # Assignment Pin # Assignment 1 Red 2 Green 3 Blue 4 NC 5 Ground 6 Ground 7 Ground 8 Ground 9 VCC 10 Ground 11 NC 12 DDData 13 Hsync 14 VSy nc 15 DDClk y Figure:  COM1 RS-232 serial port conn ector (D-Sub 9-pins male): CN2 Pin # Assignment Pin # Assignment 1 DCD (Data[...]

Installations 21  Parallel port connector (D-Sub 25 -pi ns female): CN3 Pin # Assignment Pin # Assignment 1 Line Printer Strobe 14 Auto Feed 2 PD 0, Parallel Data 0 15 Error 3 PD 1, Parallel Data 1 16 Initialize 4 PD 2, Parallel Data 2 17 Select 5 PD 3, Parallel Data 3 18 Ground 6 PD 4, Parallel Data 4 19 Ground 7 PD 5, Parallel Data 5 20 Ground[...]

Installations 22  PS/2 keyboard connector (6-pins p urple mini Din): CN5 Pin # Assignment Pin # Assignment 1 Keyboard data 2 NC 3 Ground 4 +5V 5 Keyboard clock 6 NC y Figure:  PS/2 mouse connector (6-pins green mini Din): CN5 Pin # Assignment Pin # Assignment 1 Mouse data 2 NC 3 Ground 4 +5V 5 Mouse clock 6 NC y Figure: 2 6 1 5 3 4 2 6 1 5 3 [...]

Installations 23  Gigabit Ethernet RJ-45 (LAN2 ) connector (RJ-45 phone-jack): CN6 Pin # Assignment Pin # Assignment 1 Transmit output (+) 5 NC 2 Transmit output (-) 6 Receive input (-) 3 Receive input (+) 7 NC 4 NC 8 NC y Figure:  USB 2/3 connectors (4 -pins female): CN6 Pin # Assignment Pin # Assignment 1a VCC 1b VCC 2a USB2 - 2b USB3 - 3a [...]

Installations 24  Gigabit Ethernet RJ-45 (LAN1 ) connector (RJ-45 phone-jack): CN7 Pin # Assignment Pin # Assignment 1 Transmit output (+) 5 NC 2 Transmit output (-) 6 Receive input (-) 3 Receive input (+) 7 NC 4 NC 8 NC y Figure:  USB 0/1 connectors (4 -pins female): CN7 Pin # Assignment Pin # Assignment 1a VCC 1b VCC 2a USB0 - 2b USB1 - 3a [...]

Installations 25  External keyboard & mouse connec tor (6-pins pin-header ): CN8 Pin # Assignment Pin # Assignment 1 MS Clock 2 MS Data 3 KB Clock 4 KB Data 5 Ground 6 VCC y Figure:  COM2 RS-232 serial port connector (10-pins pin-header): CN9 Pin # Assignment Pin # Assignment 1 DCD 2 DSR 2 RXD 4 RTS 3 TXD 6 CT S 4 DTR 8 RI 5 Ground 10 5V [...]

Installations 26  18/24Bits LVDS panel interfac e (40-pins male): CN10 Pin # Assignment Pin # Assignment 1 NC 2 NC 3 Ground 4 Ground 5 YAM0 6 YAM1 7 YAP0 8 YAP1 9 Ground 10 Ground 11 YAM2 12 CLKAM 13 YAP2 14 CLKAP 15 Ground 16 Ground 17 YAM3 18 YBM0 19 YAP3 20 YBP0 21 Ground 22 Ground 23 YBM1 24 YBM2 25 YBP1 26 YBP2 27 Ground 28 Ground 29 CLKBM [...]

Installations 27  USB 4/5 connector (9-pins pin-header): CN11 Pin # Assignment Pin # Assignment 1 VCC 2 VCC 3 USB4 - 4 USB5 - 5 USB4 + 6 USB5 + 7 Ground 8 Ground 9 --- 10 NC y Figure:  System fan po wer connector: CN13 Pin # Assignment 1 Ground 2 VCC 3 Fan Status Signal y Figure: 2 1 9 10 1 3[...]

Installations 28  CPU fan po wer connector: CN14 Pin # Assignment 1 Ground 2 VCC 3 Fan Status Signal y Figure:  Audio Line_out pin-header: CN15 Pin # Assignment 1 LOUT_L 2 Ground 3 Ground 4 LOUT_R y Figure: 1 3 1 4[...]

Installations 29  Secondary IDE connector (40 -pins 2.54mm pitch pin-header with housing): CN16 Pin # Assignment Pin # Assignment 1 Reset IDE 2 Ground 3 Host Data 7 4 Host Data 8 5 Host Data 6 6 Host Data 9 7 Host Data 5 8 Host Data 10 9 Host Data 4 10 Host Data 11 11 Host Data 3 12 Host Data 12 13 Host Data 2 14 Host Data 13 15 Host Data 1 16 H[...]

Installations 30  Floppy disk connector (34-pins 2.54mm pitch pin-he ader w ith housing): CN17 Pin # Assignment Pin # Assignment 1 Ground 2 Drive Density Selection 3 Ground 4 NC 5 Ground 6 Drive Density Selection 7 Ground 8 Inde x 9 Ground 10 Motor Enable 0 11 Ground 12 Drive Select 1 13 Ground 14 Drive Select 0 15 Ground 16 Motor Enable 1 17 Gr[...]

Installations 31  CD_IN pin-header: CN18 Pin # Assignment 1 CD_IN_Left 2 CD_GND 3 CD_GND 4 CD_IN_Right y Figure:  20-pins ATX po wer connector: CN19 Pin # Assignment Pin # Assignment 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 Ground 13 Ground 4 +5V 14 PS-ON 5 Ground 15 Ground 6 +5V 16 Ground 7 Ground 17 Ground 8 NC 18 -5V 9 5VSB 19 +5V 10 +12V 20 +5V[...]

Installations 32  Primary IDE connector (40-pins 2.54mm pitch pin-header w ith housing): CN20 Pin # Assignment Pin # Assignment 1 Reset IDE 2 Ground 3 Host Data 7 4 Host Data 8 5 Host Data 6 6 Host Data 9 7 Host Data 5 8 Host Data 10 9 Host Data 4 10 Host Data 11 11 Host Data 3 12 Host Data 12 13 Host Data 2 14 Host Data 13 15 Host Data 1 16 Hos[...]

Installations 33  System panel indicate conne ctor: CN21 Pin # Assignment Pin # Assignment SPEAKER PWR LED 1 +5V 2 5V 3 NC 4 NC 5 BZ 6 Ground 7 SPKR KEYLOCK HDD LED 8 KBLOCK 9 5V 10 Ground 11 HDLED- 12 NC RESET PWR ON 13 RESET+ 14 5VSB 15 Ground 16 PWRBT- y Figure:  LAN2 LED pin-header: JP1 Pin # Assignment Pin # Assignment 1 LINK_LED 2 VCC_3[...]

Installations 34  LAN1 LED pin-header: JP2 Pin # Assignment Pin # Assignment 1 LINK_LED 2 VCC_3V 3 ACT_LED 4 VCC_3V y Figure: 1 2 4 3[...]

35 A WARD BIOS S ETUP 3.1 BIOS Instructions Award’s ROM BIOS provides a built-in Setup pro gram, which allows user to modify the basic system co nfiguration and hardwa re parameters. The modified data will be stored in a battery-backed CMOS, so that data will be retained even when the power is turn ed off. In general, the information saved in the[...]

Award BIOS Setup 36 3.2 Main Menu Once you enter the AwardBIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to sel ect from several setup functions and t wo exit choices. Use the arrow keys to select among the items and press <Enter> to accept and enter the sub-menu. Phoenix - AwardBIOS CMOS Setup U[...]

Award BIOS Setup 37 Power Management Setup: Use this menu to specify your settings f or power managem ent. See 3.8 for the details. PnP / PCI Configuration: This entry appears if your system support s PnP / PCI. See 3.9 for the details. PC Health Status: Use this menu t o show y ou r syst em temperature, speed and voltag e status. See 3.10 for the [...]

Award BIOS Setup 38 3.3 Standard CMOS Featur es The items in Standard CMOS Setup Menu a re divided into 10 categories. Each category include s no, one or more than one setup items. Use the arrow keys to highlight t he item and then use the <P gUp> or <PgDn> keys to select the value you wa nt in each ite m. Phoenix - AwardBIOS CMOS Setup[...]

Award BIOS Setup 39 IDE Secondary Master: Options are in it s sub m enu (described in 3.4) Press <Enter> to enter the s ub menu of detailed o ptio ns. IDE Secondary Master: Options are in it s sub m enu (described in 3.4) Press <Enter> to enter the s ub menu of detailed o ptio ns. Drive A/ Drive B: Options Non e 360K, 5 .25 in/1.2M, 5.2[...]

Award BIOS Setup 40 3.4 IDE Adapters The IDE adapters control the hard di sk drive. Use a separate sub menu to configure each hard disk drive. Phoenix - AwardBIOS CMOS Setup Utility IDE Primary Master IDE HDD Auto-Detection IDE Primary Master Access Mode Capacity Cylinder Head Precomp Landing Zone Sector Press Enter Auto Auto 13579 MB 26310 16 0 26[...]

Award BIOS Setup 41 The following options are selectable only if the ‘IDE Primary Ma ster’ item is set to ‘Manual’ Cylinder: Options Min = 0, Max = 65535 Set the number of cylinders for this hard disk. Head: Options Min = 0, Max = 255 Set the number of read/write heads Precomp: Options Min = 0, Max = 65535 **** Warning : Setting a value of [...]

Award BIOS Setup 42 3.5 Adv anced BIOS Features This section allows you to configu re your system for basic operat ion. You have the opportunity to select t he system’s default speed, boot-up sequence, keyboard opera tion, shadowing and secu rity. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features ¾ CPU Feature Virus Warning CPU L1 &a[...]

Award BIOS Setup 43 Thermal Management: It allows you to select the thermal Monitor. The Choice: Thermal monitor1, thermal Monitor2. Virus Warning: Allow you to choose the virus-warning feature for IDE Hard Di sk boot secto r protection. If this function is enabled an d someone attempts to write data into this area, BIOS will show a warning message[...]

Award BIOS Setup 44 Swap Floppy Driv e: If the system has two floppy drives, you can swap t he logical dri ve name assignments. The choice: Enabled, Disabled. Boot Up Floppy Seek: Seeks disk drives during b oot up. Disabling speeds boot up. The choice: Enabled, Disabled. Boot Up NumLock Statu s: Select power on state for NumLoc k. The choice: On, O[...]

Award BIOS Setup 45 Note: To disable security, select PASSWORD SETTIN G at Main Menu and then you will be asked to enter password. Do not type any thing a nd just press <Enter>, it will disable security. Once the security is disabled, the system will boot and you can enter Setup freely. APIC Mode: This item allows you to enable API C (Advance[...]

Award BIOS Setup 46 3.6 Adv anced Chipset Features This section allows you to configur e the system based on the specific features of the installed ch ipset. This chipset manages bus speeds and access to system memory resou rces, such as DRAM and the external cache. It also coordinates communi cations betwee n the conventional ISA bus and the PCI b[...]

Award BIOS Setup 47 Active To Precharge Delay: Select the operating system that is active to precharg e delay. The choice: 5, 6, 7. DRAM RAS# To CAS# De lay: This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refre shed. Fast gives faster performance; and Slow give s more[...]

Award BIOS Setup 48 Memory Hole At 15M-16M: You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user info rmation of peripherals that need to use this area of system m emory usually discusse s their memory requirement s. The choice: Enabled, Disabled. Delayed Transaction: The chipset [...]

Award BIOS Setup 49 3.7 Integrated Peripherals Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals ¾ OnChip IDE Device ¾ Onboard Device ¾ SuperI/O Device Onboard Lan Boot ROM Press Enter Press Enter Press Enter Disabled Item Help ____________________________ Menu Level ¾ ↑↓←→ Mov e Ent er: Sel ect + /-/PU /PD: V alue F 10: Sa [...]

Award BIOS Setup 50 IDE Primary/Secondary Master/Slave PIO: The four IDE PIO (Programmed Input/Out put) fields let you set a PIO mode (0-4) for each of the four IDE devic es that the o nboard IDE interface supports. Modes 0 through 4 provide successively increa sed performance. In Auto mode, the system automatica lly determine s the best mode for e[...]

Award BIOS Setup 51 USB Keyboard Support: Select “Enabled” if your system cont ains a Universal Serial Bus (USB) controller and you have a USB keyboard. The choice: Enabled, Disabled. USB Mouse Support: Select “Enabled” if your system cont ains a Universal Serial Bus (USB) controller and you have a USB mouse. The choice: Enabled, Disabled. [...]

Award BIOS Setup 52 Power On Function: Options Password, Hot KET, Any KEY, BUTTON and Keyboard 98. You can use this item to select operating Powe r On the system. KB P o wer ON P ass wor d : Option Enter You can set password to limit operating KB Power On system. Hot Key Po w er ON: Options Ctrl+F1 ~ Ct rl+F12 You can use this item to select operat[...]

Award BIOS Setup 53 Use IR Pins: This item allows you to sel ect IR transmission routes, one is RxD2, TxD2 (COM Port) and the other is IR-Rx2Tx2. The choice: IR-Rx2Tx2, RxD2 and TxD2. Onboard Parallel Port: This item allows you to determine ac cess onboard parall el port controller with which I/O address. The choice: 3BC/IRQ7, 37 8/IRQ7, 278/I RQ5 [...]

Award BIOS Setup 54 3.8 Po wer Management Setup The Power Manageme nt Setup allows you to configu re you system to most effectively save energy while operating in a m anner consistent with your own style of computer use. Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup Video Off Method Video Off In Suspend Suspend Type Suspend Mode HDD[...]

Award BIOS Setup 55 Video Off In Suspend: This determines the manne r in which the monitor is blanked. The choice: Yes, No. Suspend Type: This determines the CP U status du ring power saving mode. The choice: PwrOn Suspend, Stop Grant . Suspend Mode: When “Enabled” and after the set time of system inactivity. All devices except the CPU will be [...]

Award BIOS Setup 56 PM Events: PM events are I/O events whose occurr ence can prevent the system from entering a power saving m ode or can awaken the system from such a mode. In effect, the system remains alert fo r anything, which occurs to a device, which is configured as Enabled, even when the system is in a power do wn mode. Primary IDE 0 Prima[...]

Award BIOS Setup 57 3.9 PnP/PCI Configurations This section describe s configuring the PCI bus system. PCI, or P ersonal C omputer I nterconnect, is a system, which allows I/O devices to operate at speeds nearing the spe ed the CPU itself uses when communicating with its own special components. T his section covers some very technical items and it [...]

Award BIOS Setup 58 Resource controlled by : The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unl ess you are using a Plug and Play operating system such as Wind ows ® 95. If you set this field to “Manual” choose spec[...]

Award BIOS Setup 59 3.10 PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature SYS Temperature CPU Temper ature CPU Fan Speed SYS Fan Speed VCC_2V5 VCORE 3.3V + 5 V +12 V -12V -5V VBAT (V) 5VSB (V) Shutdown Temperature Disabled 34°C/93°F 40°C/104°F 5010RPM 5213RPM 2.48V 1.29V 3.28V 4.97V 12.03V -11.54V[...]

Award BIOS Setup 60 3.11 Frequency/Voltage Control Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect PCI CLK Spread Spectrum Enabled Disabled Item Help ____________________________ Menu Level ¾ ↑↓←→ Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-safe defaults[...]

Award BIOS Setup 61 3.12 Load Fail-Safe Defaults When you press <Enter> on this item y ou get a confirmation dialog box with a message similar to: Load Fail-Safe Defaults (Y/N)? N Pressing ‘Y’ loads the BIOS default values f or the most stable, minimal-performance system operations. 3.13 Load Optimized Defaults When you press <Enter>[...]

Award BIOS Setup 62 3.14 Supervisor/User Password Setting You can set either supervisor or us er p assword, or both of then. The differences between are: Set Supervisor Pass word: can enter and change the options of the setup menus. Set User Pass word: just can only enter but do not have the right to change the options of the setup menus. When you [...]

Driver Utility Installation 63 3.15 Exit Selecting Save & Exit Setup Pressing < Enter> on this it em asks for confirmation: Save to CMOS and EXIT (Y/N)? Y Pressing “Y” stores the selection s made in the menus in CMOS – a special section of memory that stays on after you turn your system off. The next time you boot your computer, t h[...]