Intel PC 8153 manual

PC 8153 ® ™ Core 15” TFT Expandable Intel 2 Duo Industrial Panel PC with 2 PCI User ’ s Manual[...]

[...]

Disclaimers This manual has been carefully checked and believed to contain accurate information. ACNODES Co. assumes no responsibility for any infringements of patents or any third party ’s rights, and any liability arising from suc h use. ACNODES does not warrant or assume any legal liabili ty or responsibility for the accuracy, completeness or [...]

Safety Approv als CE Marking FCC Cla ss A FCC Co mplia nc e This equipment has been tested in compliance wit h the limits for a Class A digita l device, pursuant to Part 15 of the FCC Rules. These limit s are meant to prov ide reasonable protection against harmful interferenc e in a residential installat ion. If not installed and used in accordance[...]

1 Safety Prec autions Before getting started, please read the following important safety precautions. 1. The PC 8153 Series does not come equipped wit h a n operating syste m. An operating syste m must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent stati c charge whe n installing the inter[...]

Before handling a board or integrated circuit, touch an unpainted portion of the syste m unit chassis for a few seconds. This wil l help to discharge any stat ic electricity on your body. When handling boards and components, wear a wri st - grounding strap, available from most electronic component stor es. Trademarks Acknowledgments ACNODES is a tr[...]

3 Table of Con tents Disclaime rs ................... ....... ............ ....... ............ ............ ............ ............. .......... ... ii Safe ty Approv als ............ ........... ............ ............ ........... ............ .......... ......... ........ iii Safe ty Precautions ............ ......... ............ ...........[...]

4.1 Syste m .......... ............. ......... ............. ............. .............. .......... ........ . 59 4.2 Touch Screen ............ ............ ........ ........... ............. ........... ............. . 60 4.2.1 Specifica tion .............. .............. .......... ........... ............ ............ .......... 60 4.2.2 Driver[...]

MEMO viii[...]

[...]

PC 815 3 User ’ Introduction 1 s Manual C h a p t e r 1 Introduction This chapter contains general information and detailed specifications of the PC 8153 . Chapter 1 includes the following sections : General Description System Specific atio n Dimens ions Front View & I/O Outlets Package List[...]

PC8153 User ’ 2 Introduction s Manual 1.1 General Description The PC 8153 is a 15” Industrial panel PC which feat ures Intel ® Core ™ 2 Duo processor and Intel ® Q965 chipset to provide powerful computing performance. This panel PC also offers the expansion ability wit h tw o PCI slots. It adopts built- in speaker and WLAN module for wir el[...]

Introduction 3 PC 815 3 User ’ s Manual 1.2 System Specifications 1.2.1 Main CPU Board CPU Socket LGA775 for Intel ® Core TM 2 Duo/Core TM Solo Processor wit h FSB 533/800/1066 MHz NOT E It does n’ t support the processor with FSB 1333 MHz, and it is not recommended to use Quad-C ore CPU. System Chipset ® Intel BIO S Q965 + ICH8 Phoenix-Award[...]

4 Introduction PC8153 User ’ s Manual Ethernet First port wit h i82566DM Gigabit Ethernet PHY, Second port wit h RTL8111B for Gigabit/Fast Ethernet Audio HD Audio for two channels output MIC-In, Line-Out Storag e Four SATA-300 interface Box-Header One 26-pin for shared LPT/FDD(optional) Expansio n Slot Tw o 32-bit PCI Master slots 1.2.3 System Sp[...]

Introduction 5 PC 815 3 User ’ s Manual Heat Dispen sing Design Tw o slots for PCI expans ion Net Weight 13 Kgs Dimen sion (Main Body Size) 420mm (16.51” )(W) x 150mm (9.14”)(D ) x 335mm (13.19”)(H) Operation Temperature 0 ℃ to 40 ℃ ; Relative Humidity 50% Relative Humidity 10% to 85% @ 40 ℃ , Non-Condensing Altitude 10,000 ft. (3,000[...]

[...]

Introduction 7 PC 815 3 User ’ s Manual 1.4 Front View and I/O Outlets 1.4.1 Front View Please refer to the following illustration for features and cont r ol s of the PC 8153 front bezel. No Function 1 SEL+ 2 SEL- 3 Backlight ON/OFF[...]

8 Introduction PC 815 3 User ’ s Manual 1.4.2 I/O Outlets The following figure shows the I/O locations of the PC 8153 . No Connec tor No Connector 1 COM1 7 COM 2 & COM 3 2 8 DVI-I Power Swi tch 3 Giga LAN x 2 9 AC power 4 10 IEEE 1394a x 2 PCI slots x 2 5 11 USB v2.0 x 4 P/S2 Keyb oard/Mous e 6 Mic-in, Line-Out[...]

Introduction 9 PC 815 3 User ’ s Manual 1.5 Package List The package bundled wit h you r PC 8153 should contain the following items: PC 8153 x 1 AC power cord x 1 Panel mount kit x 7 Driver CDx1 LGA 775 CPU Cooler x 1 DVI TO VGA Adaptor x 1 PS/2 Splitter – Y Cable x 1 SATA Cable x 1 Dual 3.5 ” HDD brack et kit wit h fan x 1 (Optional) Small H[...]

10 Introduction PC 815 3 User ’ s Manual MEMO[...]

[...]

PC 815 3 User ’ s Manual 12 Hardw a r e Installation C h a p t e r 2 Hardw are Installati on The PC 8153 is convenient for your various hardware configurations in flexible ways , such as CPU (Central Processing Unit), HDD (Hard Di sk Drive), Memory Module (DRAM), CD-ROM, Add-On card, and more. The chapter 2 will show you how to install the hardwa[...]

PC 815 3 User ’ s Manual Hardware Installation 13 Step 1 Unscrew screws to remove the rear chassi s. Step 2 Remove the riser car d fix kit .[...]

PC 815 3 User ’ s Manual 14 Hardw a r e Installation Step 3 Install the CPU and DDR DRAM in the PC 8153. DRAM CPU[...]

PC 815 3 User ’ s Manual Hardware Installation 15 2.2 Installing the the Hard Disk Drive The PC 8153 off ers a convenient drive bay module for users to install HDD. The system offers users two 3.5” Hard Disk Drives for installation. If you wan t to install one or two 2.5 ” HDD, the PC 8153 also provides the 3.5” to 2.5” drive holder to me[...]

PC 815 3 User ’ s Manual 16 Hardw a r e Installation Step 4 The installa tion is completed. Installing Dual 3.5 ” HDD If installing the dual 3.5 ” HDD, please follow the steps : Step 1 Change HDD bracket from 3.5 ” to dual 3.5 ” .[...]

PC 815 3 User ’ s Manual 17 Hardware Installation Step 2 Fix the Hard Disk to the HDD bracket to complete the installation.[...]

PC 815 3 User ’ s Manual 18 Hardw a r e Installation Note When installing Dual 3.5 ” HDD, users must install a fan to decrease system heat. Installation step as following: Installing fan wh e n using dual 3.5 ” HDD Step 1 Screw the fan to the right side of cov er . (1-1)[...]

PC 815 3 User ’ s Manual Hardware Installation 19 (1-2) (1-3) Step 2 Connect power cable of fan to 3 pin fan connector (CN3) in motherboard.[...]

PC 815 3 User ’ s Manual 20 Hardw a r e Installation If installing the 2.5 ” HDD, pleas e follow the steps: Step 1 Set the 2.5” HDD in the HDD bracket kit. Step 2 Install the HDD in the PC 8153.[...]

PC 815 3 User ’ s Manual Hardware Installation 21 2.3 CD-ROM Installation The PC 8153 off ers a convenient drive bay module for users to install CD-ROM. When installing the CD-ROM, refer to the fo llow ing instructions and illustration: Step 1 Unscrew screws to remove the rear chassis. Step 2 Remove the riser card fix kit. Step 3 Unscrew 3 screws[...]

PC 815 3 User ’ s Manual 22 Hardw a r e Installation 2.4 Add-on Car d Installation The PC 8153 provides a riser card for PCI slots expansion. The riser card assembly can accommodate both half-size expansion cards. To install the riser card, refer to the following figure and instructions below: Step 1 Remove the rear chassis. Setp 2 Remove the ris[...]

PC 815 3 User ’ s Manual Hardware Installation 23 Step 4 Insert the add-on card in the socket firmly until it is completely seated.[...]

PC 815 3 User ’ s Manual 24 Hardw a r e Installation 2.5 Serial Por t Interface The PC 8153 has three onboard serial ports, COM1, COM 2 , a nd COM 3 . COM1 is RS-232(default)/422/485 Port Connec tor while COM2 and COM3 are RS-232 Port Connectors. The connector, COM 1, COM 2, COM3 are DB-9 connector, and the following table shows the pin assignmen[...]

PC 815 3 User ’ s Manual Hardware Installation 25 19 Ground 20 NC Pin Signal Pin Signal 21 NC 22 Ground 23 TXC+ 24 TXC- C1 CRT-RED C2 CRT-GREEN C3 CRT-BLUE C4 CRT-HSYNC C5 VGAGND C5 1 8 C1 C2 9 16 17 24 C3 C4 C5 NOTE It doesn’ t support display in LCD and DVI-D simultaneously. DVI-D is only available aft er booting up in Windows XP.[...]

PC 815 3 User ’ s Manual 26 Hardw a r e Installation Pin Signal 1 TX+ (Data transmissi on positive 2 TX- (Data transmission negative) 3 Rx+(Data rec ep ti on positive) 4 2.7 Ethernet The PC 8153 provides a NE2000 compatible Ethernet (RJ-45) interfaces. For network connection, just plug in one cable end of the system’s 10/100/1000-Base-T Hub int[...]

PC 815 3 User ’ s Manual Hardware Installation 27 2.8 Mountings Way – Panel There is one application option for the PC 8153, Panel mounting. Panel – Mount Kit Asse mble y The PC 8153 is designed for panel mount application. To mount the PC 8153 , the standard set of mounting kit (included in the sys te m packaging) is needed.[...]

PC 815 3 User ’ s Manual 28 Phoeni x -Award B I OS Utility C h a p t e r 3 Phoenix-Award BIOS Utility The Phoenix-Award BIOS provides users wit h a built -in Setup program to modify basic sys tem configuration. All configured parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 29 3.2 Control Ke ys Up arrow Move cursor to the prev ious item Dow n arrow Move cursor to the next item Left arrow Move cursor to the item on the left hand Right arro w Move to the item in the right hand Esc key Main Menu -- Quit and delete changes into CMOS Status Page Setup Menu and Optio[...]

PC 815 3 User ’ s Manual 30 Phoeni x -Award B I OS Utility 3.4 The Main Menu Once you enter the Award BIOS CMOS Setup Uti lity, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for you r selection. Use arrow keys to select the Setup Page you intend to configure then press <En[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 31 3.5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your sys tem. Use arrow key s to highlight each item, and use <PgUp> or <PgDn> key to select the value you want in each item . Date The date format is <day>, <date> <month[...]

PC 815 3 User ’ s Manual 32 Phoeni x -Award B I OS Utility IDE Primary Master/Primary Slave These item s identify the type s of each IDE channel installed in the computer. There are 45 predefined types (Typ e 1 to Type 45) and 2 user’s definable types (Type User) for Enhanced IDE BIO S. Press <PgUp>/<+> or <PgDn>/< > to [...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 33 Press <Esc> to return to the Main Menu page. 3.6 Adva nced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference.[...]

PC 815 3 User ’ s Manual 34 Phoeni x -Award B I OS Utility CPU Feature Scroll to this item and press <Enter> to view the CPU Featur e sub menu. Hard Disk Boot Priority Scroll to this item and press <Enter> to view the sub menu to decide the disk boot prior ity.[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 35 Virus Warning This option flashes on the screen. During and after the sy s te m boot up, any attem pt to wri te to the boot sector or partition table of the hard disk drive will halt the system wit h the following message. You can run an anti-virus program to locate the problem. The defau[...]

PC 815 3 User ’ s Manual 36 Phoeni x -Award B I OS Utility First/Second/ Third Boot Device These item s let you sel ec t the 1st, 2nd, and 3rd devices that the system will search for during its boot-up sequence. The wid e range of selection includes Floppy, LS120, ZIP100, HDD0~3, SCSI, and CDROM. Boot Other Device This item allows the user to ena[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 37 Ty pematic Rate (Chars/Sec) This option refers to character numbers typed per second by the keyboard. The default value is “6” . 6 characters per second 6 8 characters per second 8 10 charac ters per second 10 12 charac ters per second 12 15 charac ters per second 15 20 charac ters pe[...]

PC 815 3 User ’ s Manual 38 Phoeni x -Award B I OS Utility API C Mode Use this item to enable or disable APIC (Advanced Programmable Interrupt Controller) mode that provides symme tr ic multi- processing (SMP) for system s. MPS Version Control For OS This item specifies the version of the Multiprocessor Specification (MPS). Version 1.4 has extend[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 39 3.7 Adva nced Chipset Features This section contains com pl et el y optimized chipset ’s features on the board that you are strongly recommend ed to leave all item s on this page at their default values unless you are very familiar wit h the technical specifications of you r system hard[...]

PC 815 3 User ’ s Manual 40 Phoeni x -Award B I OS Utility PCI Express Root Port Func Scroll to this ite m and press <Enter> to view the sub menu to decide the PCI Express Port. Press <Esc> to return to the Advanced Chi p se t Featurs page. *** VGA Setting *** PEG/Onchip VGA Control Use this it em to choose the prima ry display card. [...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 41 Boot Displ ay This item is for Intel define ADD card only. Press <Esc> to return to the Main Menu page. 3.8 Integrated Peripherals This section allows you to configure your SuperIO Device, IDE Function and Onboard Device.[...]

PC 815 3 User ’ s Manual 42 Phoeni x -Award B I OS Utility On-Chip IDE Device Scroll to this item and press <Ent er> to view the sub menu On-Chip IDE Device. IDE HDD Bloc k Mode Block mode is also called block transfer, multiple commands, or multiple sector re ad /w rite . If your IDE hard drive supports block mode (most new drives do), sel[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 43 Master/Slave PIO items on the menu. IDE Master/Slave PIO The four IDE PIO (Programmed Input/Out put) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 to 4 provide succes sively increased performance. In Auto mode, the sy[...]

PC 815 3 User ’ s Manual 44 Phoeni x -Award B I OS Utility Super IO Device Scroll to this ite m and press <Enter> to view the sub menu Super IO Device. Onboard FDC Control ler Select Enabled if your sy st e m has a floppy disk controller (FDC) installed on the syste m board and you wish to use it. If you inst all and-in FDC or the syste m h[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 45 Parallel Port Mode Select an operating mode for the onboard parallel (printer) port. Select Normal unless you r hardware and sof twa re require one of the other modes offered in thi s field. The options available are EPP1.9, ECP, SPP, ECPEPP1.7, EPP1.7. ECP Mode Use DMA Select a DMA chann[...]

PC 815 3 User ’ s Manual 46 Phoeni x -Award B I OS Utility 3.9 Power Management Setup The Power Management Setup allows you to sav e energy of you r system effectively. It will shut down the hard disk and turn OFF video display after a period of inactivity.[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 47 ACP I Function This item allows you to enable/disable the Advanced Configuration and Power Management (ACPI). The function is always “ Enabled ”. ACP I Suspend Ty pe This item specifies the power saving modes for ACPI function. If your operating sys tem supports ACPI, such as Windows [...]

PC 815 3 User ’ s Manual 48 Phoeni x -Award B I OS Utility to restore the system whe n a “wake up” event occurs. Run VG ABIOS if S3 Resume When this item is set Auto, the system will run VGA BIOS if it is reaumed from the S3 stat e. Pow er Manageme nt This option allows you to select the typ e (or degree) of power saving for Doze, Standby, an[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 49 connect the fax/modem to the board Wake On Modem connector for work ing thi s feat ure. Suspend Mode After the sel ect ed period of system inactivity (1 minute to 1 hour), all devices except the CPU shut off. The default value is “Disabled ” . System wil l never enter SUSPEND mode Dis[...]

PC 815 3 User ’ s Manual 50 Phoeni x -Award B I OS Utility ** Reload Global Timer Even ts ** Global Timer (power management) events can prevent the sys te m from entering a power saving mode or can awaken the system from such a mode. Primary/Secondary IDE 0/1 Use thi s item to configure the IDE devices monitored by the system. FDD, COM, LPT Port [...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 51 3.10 PnP/PCI Configuration Setup This sec ti on describes configuring the PCI bus sys tem. PCI, or Personal Computer Interconnect, is a system whic h allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating wit h it s own special components. This se[...]

PC 815 3 User ’ s Manual 52 Phoeni x -Award B I OS Utility interrupt to one of the following types in accordance wit h the typ e of devices using the interrupt: 1. Legacy ISA Devices complia nt wit h the original PC AT bus specification, requiring a specific interrupt (suc h as IRQ4 for serial port 1). 2. PCI/ISA PnP Device s complia nt wit h the[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 53 3.11 PC Health Status This sec ti on supports hardware monitori ng tha t lets you monitor those parameters for cri tica l voltages, temperatures and fan speed of the board. Shutdow n Temperature It helps you set the maximum temperature the y sys tem can reach before powering down. Current[...]

PC 815 3 User ’ s Manual 54 Phoeni x -Award B I OS Utility 3.12 Frequency/Voltage Control This section is to control the CPU frequency and Supply Voltage, DIMM OverVoltage and AGP voltage. CPU Clo ck Ratio Use this it em to sel ect the CPU’s frequency. Aut o Detect PCI Clk The enabled item can automatically disable the clock source for a PCI sl[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 55 3.13 Load Optimized Defaults This option allows you to load the default values to you r syste m confi gurat ion. These default settings are optimal and enable all high performance features. To load SETUP defaults value to CMOS SRAM, enter “Y”. If not, enter “N” .[...]

PC 815 3 User ’ s Manual 56 Phoeni x -Award B I OS Utility 3.14 Set Superv i sor/User Password You can set either supervisor or user password, or both of then. The differences between are: 1. Supervis or passw ord: can enter and change the options of the setup menus. 2. User passw ord: just can enter but do not have the right to change the option[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 57 3.15 Save & Exit Set up This allows you to determine whether or not to accept the modifications. Typing “Y” quits the setup utility and saves all changes into the CMOS memory. Typ ing “N” brigs you back to Setup utilit y.[...]

PC 815 3 User ’ s Manual 58 Phoeni x -Award B I OS Utility 3.16 Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” wil l quit the Setup uti lity without saving the modifications. Typing “N” wil l return you to Setup utility.[...]

PC 815 3 User ’ s Manual Phoeni x -Award B I OS Utility 59 MEMO[...]

PC 815 3 User ’ s Manual 60 Driver Ins t allation C h a p t e r 4 Driver Installation 4.1 System PC 8153 supports Windows 2000/XP/Vista. To facilita te the installation of the sys tem driver, please carefully read the instructions in this chapter before start installing. 1. Here is the path for the system driver: Panel seriesPC 8153Dri ver 2. S[...]

PC 815 3 User ’ s Manual Driver Ins t allation 61 4. 2 Touch Screen 4.2.1 Specificatio n Touch Screen 5-wire Analog Resistive type Touch Screen Control ler DMC9000 (10-bit A/D conver ter inside) Communica tions RS-232 Baud Rate 19200 and 9600 baud selection Resolution 2048 x 2048 Mode Select ion PnP or non-P nP Power Input 5V DC Power Consumption[...]

PC 815 3 User ’ s Manual 62 Driver Ins t allation 4.2.2 Driver Installa tion – W indow s 2000/XP/Vista The PC 8153 provides a drive r of the touch screen that users can install it under operating sys te m Windows 2000/XP/Vista. To facili tate this touch screen driver installation, users should read the instructions in this chapter car e fu ll y[...]

PC 815 3 User ’ s Manual Driver Ins t allation 63 4. Select the “Standard Cal ibr a te ” tab .[...]

PC 815 3 User ’ s Manual 64 Driver Ins t allation 5. Calibration: To adjust the display wit h touch panel, click “Calibration” and follow the calibrate point to do calibration; there are fi ve points on screen for calibration. 6. Press OK.[...]

PC 815 3 User ’ s Manual Driver Ins t allation 65 4.2.3 Driver Installa tion - DOS Using “INSTALL.EXE ” Utility to Install Pen Mount Softw are Driver 1. Insert Driver CD and select the Panel seriesP1153- 841DriverSt ep5 - TouchDriver DOSInstall.exe 2. Press ENTER key to install the drive rs to drive C or use keyboard to key-in the hard [...]

PC 815 3 User ’ s Manual 66 Driver Ins t allation C:PEN MOUNTPMDET ECT -N5 -N9 Do Calibration 1. To adjust the touch screen mapping properly to display screen, use PM.BAT (C:PEN MOUNTPM) to do calibration. Choose “1 ” DO CALIBRATION (adjust screen mapping). 2. The message pops out to ask if you select the video mode number. Use keyboard t[...]

PC 815 3 User ’ s Manual Driver Ins t allation 67 MEMO[...]

PC 815 3 User ’ s Manual 68 Power Supply Specification A p p e n d i x Power Supply Specification Power Suppl y FSP250-50GUB (250W, AC100~240 V Input) 1. Electrical Requirements OUTPUT ELECT RICAL REQUIREMENTS The subject power supply will meet all elec trical specifications below, over the full operation temperature range and dynamic load regula[...]

PC 815 3 User ’ s Manual Power Supply Specif i cat io n 69 LOAD CA PA CITY SPECIFICATIONS The cross regulation defined as follows, the voltage regulation limits DC include DC Output ripple & noise. LOA D +3.3V +5V +12V -12V +5VSB Condition_1 X X X X 2A Condition_2 0.5A 0.3A 1A 0A 0.1A Condition_3 0.5A 2A 2A 0.8A 0.1A Condition_4 1A 2A 17A 0.1[...]

PC 815 3 User ’ s Manual 70 Power Supply Specification SHORT CIR CUIT PROTECTION Output short circuit is defined to be a short ci rc ui t load of less than 0.1 ohm. In the event of an output short circuit condition on +3.3V, +5V or +12V output, the power supply will shutdown and latch off. The power supply shall return to normal operation after t[...]

PC 815 3 User ’ s Manual Power Supply Specif i cat io n 71 Vibration: 0.25G, 10~250Hz Shock: -40G, 11mSec for Storage, -10G, 11mSec for operating 4. Reliability The power supply reliabili ty, when calculated by MIL- HDBK; latest revision, are exceed 100,000 hours with all output at maximum load and an ambient temperature of 25 ℃ . 5. Safety NEM[...]