Intel TPC-1070 manual

TPC-1070 Intel T ouch Panel Computer with High Luminance 10.4" SVGA TFT LCD User Manual[...]

TPC-1070 User Manual ii Copyright The documentation and th e software included with this product are copy- righted 2007 by Advantech Co., Lt d. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time wi thout notice. No part of this man- ual may be reproduced, copied,[...]

iii Product W arranty (2 years) Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in mat erials and workm anship for two years from the date of purchase. This warranty does not apply t o any products which have b een repaired or altered by persons other than repair perso nnel authorized by Adv[...]

TPC-1070 User Manual iv Declaration of Conformity CE This product has passed the CE test for environmental specificati ons when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for orderi ng information. FCC Class A Note: This e[...]

v Safety Instructions 1. Read these safety instructions carefully . 2. Keep this User's Manual for later reference. 3. Disconnect this e quipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. 4. For plug-in equipment, the power outlet socket must be located near the equipment and mu[...]

TPC-1070 User Manual vi 20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM- AGE THE EQUIPMENT . THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT . 16. CAUTION: DANGER OF EX PLOSION IF BA TTER Y IS INCORRECTL Y REPLACED. REPLACE ONL Y WITH THE SAME OR EQUIV ALENT TYPE RECOMMENDED BY THE MANUF ACTURER, DISCARD USED BA TTERIES ACCORD- ING TO[...]

vii 1 1. W ird das Gerät über einen längeren Zeitraum ni cht benutzt, sollten Sie es vom Stromnetz tr ennen. Somit wird im Falle einer Überspan- nung eine Beschädigung vermieden . 12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät g elangen. Dies könnte eine n Brand bzw . elektrischen Schlag ausl?[...]

TPC-1070 User Manual viii[...]

ix Table of Contents Contents Chapter 1 General Information ....................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ ........... .............. .............. ............ ..... 2 1.2.1 Syst em Kernel .. ............ ........ ............[...]

TPC-1070 User Manual x 5.3.3 HORM .. ........... ......... ........... ......... ............ ........ ........... 38 Appendix A Serial Port Settings ........................................ 40 A.1 COM1/ COM3 Connector Defi nition .................... ......... 40 A.2 COM4 Setting ..... ............ .............. .............. ........... .......[...]

xi Table of Contents Figure F.13:Plot Calibrati on Data .... ........... ......... ........ 75 Figure F.14:Draw .......... ........... ......... ........... ......... ...... 76 Figure F.15:Clear Screen ... ........... ............ ........ ........... 76 Figure F.16:Option ........ ........... ........... ......... ........... .... 77 Appendix G Fu[...]

TPC-1070 User Manual xii[...]

2 CHAPTER 1 General Information Sections include: • Introduction • Specifications • LCD Specifications • T ouchscreen Specifications • Power • I/O Ports Arrangement • Panel Mounting • Dimensions & Cutout[...]

TPC-1070 User Manual 2 Chapter 1 General Information This chapter gives the background information about the TPC -1070. 1.1 Introduction The TPC-1070 touch panel computer is state-of-the-art HMI (Human Machine Interface). This 10.4” display operator interface is an x86-based platform with these key features: Fanless: By using a low power processo[...]

3 Chapter 1 1.2.2 I/O Port s 3 serial ports : RS-232 (COM1, COM3) and RS-232/422/485 (COM4) 2 RJ-45 Ethernet port : TPC-1070H-P1E, LAN 1(10/10 0BaseT); LAN 2(10/100/100 0BaseT) TPC-1070H-C1E, LAN 1(10/100BaseT); LAN 2(10/100BaseT) 1 PS/2 port : 6-pin mini-DIN ports for keyboard and mo use 2 USB ports : compliant with USB 2.0 1 Compact Flash Slot: T[...]

TPC-1070 User Manual 4 1.3 LCD Specifications Display T ype TFT color LCD Size (diagona l) 10.4” Maximum Resolution 800 x 600 (SVGA) Maximum colors 260K Pixel Pitch (W x H) 0.264 x 0.264 mm Viewi ng Angle -70~70° (H), -60~50° (V); CR>=10 Luminance (cd / m 2 ) 400 Contrast Ratio 500 Operating T emperature -20~70° C (Ambient) Backlight 2 CCFL[...]

5 Chapter 1 1.4 T ouchscreen Specifications 1.5 Power Input voltage : 18 ~ 32 Vdc (the fuse will be open circuit as input level exceeds 33Vdc) Ty p i c a l : 24V@2.5A (60W) T ou chscreen T ype Resistive Base Glass Construction T emp ered Gl ass Resolution 1024 x 1024 Light T ransmission 75% typical Controller RS232 Interface Power Rating 3.3 to 5V [...]

TPC-1070 User Manual 6 1.6 I/O Port Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.1: I/O port arra ngement[...]

7 Chapter 1 1.7 Panel Mounting 1. There is a piece of adhesive waterproof gasket on the Mg-AL front bezel. Make sure the wate rproof gasket is in position before installing the TPC-10 70 to the panel opening. 2. Install the TPC-1070 to the panel open ing. 3. Find out t he eight clampe rs and eight long screws in the accessory pack. Hook those clam [...]

TPC-1070 User Manual 8 1.8 Dimensions & Cutout We i g h t :: 3.5 Kg (without HD D) Dimensions : 286 x 226 x 58mm (WxHxD) Cutout : 279.5 x 219.5 mm (suggested) Figure 1.3: Dimensions[...]

2 CHAPTER 2 System Setup[...]

TPC-1070 User Manual 10 Chapter 2 System Setup This chapter provides a brief explanation for operating th e TPC-1070. It is easy to make the TPC-1070 start worki ng with the below step-by-step. Step 1: Unpack the TPC- 1070 package. Please ch eck the packing list at the beginning of this manu al. Step 2: Install a CompactFlash containing w indows CE[...]

11 Chapter 2 Figure 2.3: Power receptor and button pin assignments Step 4: Plug the power lines to the system power receptor . Step 5: Push the power button to power on the system as the figu re 2.4. Step 6: Calibrate the touchscreen. Please go to: “S tart” Æ ”Settings” Æ ”Contr o l Panel” as the figure 2.5. Then, click the tab “Sty[...]

TPC-1070 User Manual 12 Figure 2.4: T ouchscreen Calibration - 1 Figure 2.5: T ouchscreen Calibration - 2[...]

2 CHAPTER 3 System Engine[...]

TPC-1070 User Manual 14 Chapter 3 System Engine Main Board Connector and Jumper Setting List Figure 3.1: Main Board Connector Label Function Description CN5 L VDS LCD Internal 18bit L VDS LC D Connector CN6 LCD POWER LCD INVERTER Connector CN7 TOUCH Internal T ouch screen Connector CN8 PCI-104 PCI-104 CN9 IDE Connector IDE connector for 40pin 2.5î[...]

2 CHAPTER 4 Sof tware Configuration Sections include: • Utilities & Drivers • Advantech CO M Dr iver Installat ion • W atchdog Timer Driver Installation[...]

TPC-1070 User Manual 16 Chapter 4 Softwar e Configuration A support CD-ROM for TPC-1070 is available and along with th e prod- uct. There are related utilities and drivers for TPC-1070 included . Please install the Chipset INF dr iver , VGA graphics driver , LAN driver , audio driver , Advantech.com driver, T ouchscreen driver and W atchdog Timer ([...]

17 Chapter 4 4.1.4 Advantech COM Driver Path: TPC-1070HDriverAdvantech COM A vailable for the OS’s below: • Microsoft W indows 2000 • Microsoft W indows XP 4.1.5 T ouchscreen Driver Path: TPC-1070HDriverPenMount A vailable for the OS’s below: • Microsoft W indows 2000 • Microsoft W indows XP 4.1.6 W atchdog Timer Driver Path: [...]

TPC-1070 User Manual 18 4.2 Advantech COM Driver Inst allation A com port named COM3 or COM4 on TPC-1070 is Advan tech Special com port. Please follow the step s below to install the driver . Step 1: Insert the companion CD-ROM int o your CD-ROM d rive. Open the directory: TPC-1070HDriverAdvantech COM Step 2: Use W indows Explorer (or W indows [...]

19 Chapter 4 Step 3: Click Next to conti nue installa tion. Step 4: Click Next to conti nue installa tion.[...]

TPC-1070 User Manual 20 Step 5: Click uninstall icon to remove ?PCI Serial Port[...]

21 Chapter 4 Step 6: Click the scan for hardware change s icon to remove ?PCI Serial Port[...]

TPC-1070 User Manual 22 Step 7: Found New Hardware and Click Next to continue installation .[...]

23 Chapter 4 Step 8: Click Finish the Advantech PCI Serial Port to continue. Step 9: Then, found New Hardware and Click Next to continue.[...]

TPC-1070 User Manual 24 Step 10: Click Finish the Advantech PCI-1602 Serial SlaveBridge to continue installati on.[...]

25 Chapter 4 Step 1 1: Found New Hardware and Click N ext to continue installa tion. Ste p 1 2 : Cl ic k Finish the Advantech PCI Serial Port t o continue.[...]

TPC-1070 User Manual 26 4.3 W atchdog Timer (WDT ) Driver Inst allation In order to ensure reliable and fa il-safe performance, TPC-1 070 has a built-in W atchdo g T im er to handle unexpected system failures. TPC- 1070 provides the drivers and a utility to activate and configure the timer for W indows2000/ XP operating systems. The following is a [...]

27 Chapter 4 4.3.1 Inst alling the TPC-1070 W atchdog Timer Driver Step 1: Insert the companion CD-ROM int o your CD-ROM d rive. Open the directory: WDT8362xW2K_ XP . Step 2: Use W indows Explorer (or W indows Run command) to execute SETUP .EXE from the companion CD-ROM.[...]

TPC-1070 User Manual 28 Step 3: Click Next to proceed.[...]

29 Chapter 4 Step 4: Click Next to confirm the customer information. Step 5: Select Advantech [W83627HF] W atchdog Timer and click Next. .[...]

TPC-1070 User Manual 30 Step 6: Click Next to confirm selecting the T ypical setup type. Step 7: Click Next to proceed.[...]

31 Chapter 4 Step 8: Click Finis h to complete the procedure. Step 9: Click OK to restart the sy stem and activate the W atchdog T imer .[...]

TPC-1070 User Manual 32 4.3.2 How to Use the TPC-1070 W atchdog Timer Step 1: Open the Control Panel, click W atchdog Service Configuration. Step 2: Click the Start Service button.[...]

33 Chapter 4 Step 3: Click Setting to select the setting page. Step 4: Select the T imer Span that meets your appli cation requirement.[...]

TPC-1070 User Manual 34 Step 5: Click Enable to enable th e setting. Step 6: Check the S tart watchdog serv ice on boot to enable the W atchdog timer to start automatical ly af ter the system boots every time. Step 7: Click OK, then the conf iguration procedure is finished. Note Use Advantech WDT Driver.WDT was enable,and WDT LED wa s 1Hz glisten.[...]

2 CHAPTER 5 Windows XP Embedded Sections include: • EWF • HORM • Advantech U tilities[...]

TPC-1070 User Manual 36 Chapter 5 Windows XP Embedded TPC-1070 is in support of embedded windows platform. This section is to state the important features, EW F and HORN, provi ded in windows XP embedded. 5.1 EWF EWF stands for Enhanced W rite Filter . It provides an upper filter in the storage device driver stack that redir ects disk write operati[...]

37 Chapter 5 Enable EWF: Run OSLock, and then syst em reboo t automatically . Open those software that customers want to directly use after system resume from hibernat ion. Hibernate via Advantech HORM utility: Please Click Start Menu->All Programs->Advantech->HORM HORM environment rem ains all along unless the following events occur: Run [...]

TPC-1070 User Manual 38 5.3.2 OSLock and OSUnLock The two utilities assist users to enable or disable EWF . Please go to Start Menu-> All Programs-> Advantech. The default setting of EWF is dis- abled. Users can protect C partition from any disk writing via OSLock that is to enable EWF RAM REG Mode . In this mode, any changes on C partition i[...]

2 APPENDIX A Serial Port Settings[...]

TPC-1070 User Manual 40 Appendix A Serial Port Settings A.1 COM1/ COM3 Connector Definition A.2 COM4 Setting The serial port COM4 on the TPC-1070 is adjustabl e. It can be set to RS- 232, RS-422 or RS-485. This port is designed with auto data flow control capability . In other word, the TPC-1070 can automatically detect the data flow direction at t[...]

41 Appendix A PIN RS-232 RS-422 RS-485 1 NDCD TX- D- 2 NRX TX+ D+ 3N T X R X + 4 NDTR RX- 5G N D 6 NDSR 7N R T S 8 NCTS 9 NRI 6 5 9 1 1 S5 ON S4 ON ON S5 S4 ON 2 S5 ON 3 4 5 6 7 8 9 0 1 2 Note: indicates the switch jumper 4321 098765 21 21 76543 21 098 1 65432 1 0987 2 S5 RS232 ON RS422-SLAVE RS485 S4 ON RS422-MASTER S4 ON[...]

TPC-1070 User Manual 42[...]

2 APPENDIX B W atchdog T imer on WinCE 5.0[...]

TPC-1070 User Manual 44 Appendix B W atchdog T imer on WinCE There is a built-in W atchdog timer on Windows CE 5.0 for TPC-1070. Y ou can access it through WIN 32 API. TPC-1070 provides a WDT driver to allow users to enable/disable the W a tchdo g timer . The driver name i s “WDT1:”. Programmers must open this driver before using the resources.[...]

45 Appendix B control codes can then be advertised , and an application can use these control codes with DeviceIoCo ntrol to perform driverspecific fu nctions. lpInBuf fer [in] Long pointer to a buffer that contains the data required to perform the operation. This parameter can be NU LL if the dwIoContro lCode parame- ter specifies an operation tha[...]

TPC-1070 User Manual 46 B.2 How to Use the Control Code There are 6 control codes for the op eration codes in the WDT driver . IOCTL _WDT_ENABLE: Enables the W atchdog tim er on your application. By default, if the W atchdog timer is enabled , the WDT driver will automatically trigger itself after the specified period and y our application do es no[...]

47 Appendix B IOCTL_WDT_GETTIMEOUT : Gets the W atchdog tim e setting. lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD pointer to your W atchdog time setting. The W atchdog tim e setting is just a number . 0 means 2 second s, 1 means 5 seconds, 2 means 10 seconds, 3 means 15 seconds, 4 means 30 seconds, 5 means 45 seconds and 6 me[...]

TPC-1070 User Manual 48 B.3 Examples #define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_UNKNOWN,ID , METHOD_BUFFERED, FILE_ANY_ACCESS) #define IOCTL_WDT_ENABLE WDT_CODE (0x900) #define IOCTL_WDT_DI SABLE WDT_CODE(0 x901) #define IOCTL_WDT_ST ROBE WDT_CODE(0x902) #define IOCTL_WDT_GET_ TI MEOUT WDT_CODE(0x903) #define IOCTL_WDT_SET_TI MEOUT WDT_CODE(0x904) #[...]

49 Appendix B // Set the W at chdog T imer as 10 seconds. Number 2 means 10 seco nds. DeviceIoControl(m_hWDT , IOCTL_WDT_SET_TIMEOUT , &nIndex, sizeof(nIndex), NULL, 0, &dwT emp, NULL); // Enable the W atchdog ti mer DeviceIoControl(m_hWDT , IOCTL_WDT_ENABLE, NULL, 0, NULL, 0, &dwT emp, NULL); While (1) { // do your job here. Sleep(8000[...]

TPC-1070 User Manual 50[...]

2 APPENDIX C W atchdog T imer Programming[...]

TPC-1070 User Manual 52 Appendix C W atchdog T imer Programming C.1 Overview The TPC-1070 cards’ watchdog t imer can be used to monit or system soft- ware operation and take corrective action if the software fails to function after the progr ammed period. Th is s ection describes the operation of the watchdog timer, and how to program it. The wat[...]

53 Chapter C C.2 W atchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. Y ou must fi rst assign the address of register by writing addr ess value into address port 2E(hex), then write/read data to/from the assigned reg ister through data port 2F (hex). F[...]

TPC-1070 User Manual 54 T able C.1: W atchdog T imer Registers Address of register (2E) Attribute Description Read/Write V alue (2F ) and description 87 (hex) ----- Write this address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer . 30 (hex) write Write 01 (hex) to enable[...]

55 Chapter C C.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; Unlock W83627HF Mov al,87h Out dx,al Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Mov al,07h ; Select registers of watchdog timer Out dx,al Inc[...]

TPC-1070 User Manual 56 Out dx,al Inc dx Mov al,10 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al 2. Enable watchdog timer and se t 5 minutes as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; unlock W83627H Mov al,87h Out dx[...]

57 Chapter C Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Set timeout interval as 5 minutes and start co unting Mov al,0f6h Out dx,al Inc dx Mov al,5 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al [...]

TPC-1070 User Manual 58 Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0f7h Out dx,al Inc dx In al,dx Or al,80h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0a[...]

59 Chapter C Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be strobed reset by keyboard Mov al,0f7h Out dx,al Inc dx In al,dx Or al,40h Out dx,al ;-------- --------- -------- --------- ---------- ---[...]

TPC-1070 User Manual 60 ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc d[...]

2 APPENDIX D Accessory Kit Assembly This appendix shows how to connect to a CD-ROM via the CompactFlash slot.:[...]

TPC-1070 User Manual 62 Appendix D Accessory Kit Assembly D.1 Comp actFlash to IDE T ransfer Kit Please follow this assembly procedur e to us e the CompactFlash slot to connect with a CD-ROM drive. 1. Connect the IDE cable to the adapter board. Figure D.1: Adapter Board and IDE Cable Figure D.2: Connecting Adapter Board & IDE Cable[...]

63 Appendix D 2. Insert the adapter board into the Co mpactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.5: Inserted Adapter Board Note Pin 1 is m arked red[...]

TPC-1070 User Manual 64 Connect the CD-ROM to the adapter board via the IDE cable and then connect the exte rnal power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.7: Plug Power Line into CD-ROM Drive D.2 USB Driver Inst allation Notice It is required to install the service pack if you want t o install the USB 2.0 d[...]

2 APPENDIX E HDD Kit Assembly[...]

TPC-1070 User Manual 66 Appendix E HDD Kit Assembly Please follow the assembly procedure to install the HDD into the system. 1. Remove the rear HDD cover . Figure E.1: Removing the Rear HDD Cover 2. Deassemble the HDD kit from th e system and remove the screws. Figure E.2: Removing the T o p Screws 3. Put the HDD into the HDD holder and fasten the [...]

2 APPENDIX F T ouchscreen I n s t a l l a t i o n & Configuration This appedix demo nstrates how to install the PenMount 9000 touchscreen and set the configuration on TPC- 1260H. This section uses W indows XP as an example.[...]

TPC-1070 User Manual 68 Appendix F T ouchscreen Inst allation & Configuration F .1 Driver Inst allation Please insert the x86 TPC series support CD and go to the W indows 2000-XP driver fold er (TPC-1070DriverT ouch ScreenDrive rW in dows 2000-XP Driver V4.0 1). Click setup.exe Figure F .1: Se tup.exe The screen displays the installat ion w[...]

69 Appendix F Figure F .3: Install – License Agreement Figure F .4: Install – Completed[...]

TPC-1070 User Manual 70 F .2 Uninst all the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Progr ams. Figure F .5: Uninstall -1 Select PenMount DMC9000 and DMC9100. Cli ck Remove butt on. Figure F .6: Uninstall -2[...]

71 Appendix F Select “Y es” to remove the PenMount W indow s 2000/SP driver and reboot the system. Figure F .7: Uninstall -3 F .3 T ouchscreen Calibration The “PM”, the i con of the PenMount Control Panel, is in the menu b ar after the touchscreen installation. Pl ease click the icon “PM” to call Pen- Mount Control Panel. It co ntains s[...]

TPC-1070 User Manual 72 Figure F .8: S tandard Calibration -1 Figure F .9: S tandard Calibration -2[...]

73 Appendix F Figure F .10: S tandard Calibration -3 Advanced Calibration is for the aged tou chscreens by using 4, 9, 16 or 25 points to calibrate touch panel. Note T ouch the red squares in sequen ce. The cali- bration is completed af ter the fifth to uch red point is calibrated. Press “ ESC” to skip.[...]

TPC-1070 User Manual 74 Figure F .1 1: Advanced Calibration -1 Figure F .12: Adva nced Calibra tion -2[...]

75 Appendix F Figure F .13: Plot Calib ration Data Draw This is to test the touch screen operation . Its display shows touch loca- tion. Note Plo t Calibration Dat a enabled provides the blue lines to show linearity before calibration and black lines to show lin earity af ter calibration when you finished the advanced calibra tion.[...]

TPC-1070 User Manual 76 Figure F .14: Draw Click “menu” and then click “clear screen” to clear the drawing. Figure F .15: Clear Screen[...]

77 Appendix F Option This option is t o set the operatio n mode and b eep sounds if t he beep sound is enabled. The operation mode, stream mode and point mode, is to enable/ disable the mouse’ s ability to drag on-screen icons. Stream mode let the mouse functions as normal and dragging on-screen. Point mode is only let the mouse a click fu nction[...]

TPC-1070 User Manual 78[...]

2 APPENDIX G Fuse S pecifications[...]

TPC-1070 User Manual 80 Appendix G Fuse S pecifications G .1 Fuse Specifications Rating : 250V AC, 3.15Amp Size : 5 x 20mm G .2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse cover back in position Figure G .1: Fuse Replacement Note The fuse is set to break as the input volta ge[...]