Jeep Liberty (2007) manual

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ............................. 1 1 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE .............................. 7 7 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ..................................[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 ▫ Roll Over W arning ..................... 4 䡵 How T o Use This Manual .................. 6 䡵 W arnings And Cautions ................... 8 䡵 V ehicle Identification Number ............... 8 䡵 V ehicle Modifications / Alterations ........... 9 1 I n f o r m a t i o n P r [...]

INTRODUCTION Thank you for selecting a Jeep 威 Liberty and welcome to our worldwide family . This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended. However , on-road ride and handling will have a differ ent feel from wha[...]

and the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not. Do not attempt sharp turns or abr upt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury . [...]

NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that the manufac- turer knows your vehicle best, has the factory-trained technicians and genuine Mopar 威 parts, and is int[...]

INTRODUCTION 7 1 I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all W arnings and Cautions. VEHICLE IDE[...]

VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. INTRODUCTION 9 1 I n f o r m a t i o n P r o v i d e d b y :[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys .................. 1 4 ▫ Ignition Key Removal ................... 1 4 ▫ Key-In-Ignition Reminder ................ 1 6 䡵 Steering Wheel Lock — If Equipped .......... 1 6 ▫ T o Manually Lock The Steering Wheel ....... 1 6 ▫ T o Release The Steering Wheel L[...]

▫ T o Unlatch The Swing Gate Flip-Up W indow . . 23 ▫ Panic Alarm .......................... 2 4 ▫ T o Use The Panic Alarm ................. 2 4 ▫ T o Program Additional T ransmitters ......... 2 4 ▫ General Information .................... 2 5 ▫ T ransmitter Battery Service ............... 2 6 䡵 Door Locks ...........................[...]

▫ Seat Belts And Pregnant W omen ............ 4 8 ▫ Seat Belt Extender ...................... 4 8 ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags .......... 4 9 ▫ Child Restraint ........................ 6 4 䡵 Engine Break-In Recommendations ........... 7 4 䡵 S a f e t y T i p s ............................[...]

A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number . The key code can also be obtained by the dealer from your vehicle invoice. Ignition Key Removal Manual T ransmission T o remove the ignition key , depr[...]

Automatic T ransmission — If Equipped T o remove the ignition key , place the gearshift lever in P (Park), turn the ignition key to LOCK and remove the key . W ARNING! Leaving children in a vehicle unattended is danger- ous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake[...]

Key-In-Ignition Reminder If you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key . STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle without the ign[...]

The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regar dless of whether or not the vehicle is locked or unlocked. During normal operation, the SKIM indicator light will come on for 3 seconds immediately after the ignition switch is turned on for a bulb check. Afterwards, if the bulb rema[...]

Important Note About Service A four digit PIN number is needed to service the Sentry Key Immobilizer System. This number can be obtained from your authorized dealer . However , this number can also be found on your customer invoice that you were given upon receipt of your vehicle. Replacement Keys NOTE: Only keys that have been programmed to the ve[...]

4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds, a single chime will sound. The SKIM indicator light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this process to program up to a total of 8 keys. General Information T[...]

T o Set the Alarm The alarm will set when you use the remote keyless entry transmitter to lock the doors and swing gate or when you use the power door lock switch while the door is open. After all the doors are locked and closed, the “Sentry Key/Security Alarm Indicator Light” (located in the instrument cluster) will flash rapidly for about 16 [...]

ILLUMINA TED ENTR Y The interior lights come on when you open any door . They will remain on for about 30 seconds after all doors are closed then fade to off, unless, the dome inhibit feature was selected on the multi-function control lever . Refer to “Lights” in Section 3 of this manual. The lights also will fade to off if you turn on the igni[...]

remain on for about 30 seconds, when you unlock the doors. The park lights will flash twice to acknowledge the unlock signal. NOTE: The transmitter can be programmed to unlock all the doors upon the first press of the ⬙ Unlock ⬙ button (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedur e: 1. Press and ho[...]

2. Continue to hold the ⬙ Lock ⬙ button, wait at least 4 but no longer than 10 seconds, then press the ⬙ Panic ⬙ button. 3. Release both buttons. 4. Repeating steps 1–3 will restore original transmitter operation. T o Unlatch the Swing Gate Flip-Up Window Press the “Rear Release” button twice to unlatch the swing gate flip-up window .[...]

Panic Alarm The panic mode flashes the park lights, and sounds the horn for about 3 minutes or until the alarm is turned off. T o Use the Panic Alarm Press and hold the P ANIC button for at least 1 second to activate the panic alarm. Press and hold the P ANIC button a second time to deactivate the alarm. The alarm will also shut itself off after st[...]

2. Enter Program Mode: T urn the ignition to the ON position, and using a currently programmed transmitter; press and hold the ⬙ Unlock ⬙ button on the transmitter . Continue to hold the “Unlock” button, wait at least 4 but no longer than 10 seconds, then press and hold the P ANIC button for at least 1 second. Release both buttons simultane[...]

T ransmitter Battery Service The recommended replacement battery is the Panasonic CR2032 or equivalent. 1. Pry the transmitter halves apart with a dime or similar object. Make sure not to damage the rubber gasket material during removal. 2. Remove and replace the batteries. A void touching the new batteries with your fingers. Skin oils may cause ba[...]

NOTE: If vehicle is equipped with the optional Elec- tronic V ehicle Information Center (EVIC) in the overhead console, all warnings including “door”, “GA TE”, and “GLASS” will only be displayed in the EVIC display (not in the instrument cluster). For additional information, refer to “Overhead Console — If Equipped” in Section 3. [...]

Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door . W ARNING! • For personal security , and safety in the event of an accident, lock the vehicle doors as y[...]

Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Ther efore, make sure the keys are not inside the vehicle before closing the door . If you pr ess the door lock switch while the keys are in the ignition [...]

Child Protection Door Lock The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks. W ARNING! A void trapping anyone in the vehicle in a collision. Remember that th[...]

WINDOWS Power Front Windows The power window switches are located on the center floor console. The top left switch controls the left front window and the top right switch controls the right front window . The lower left switch controls the left rear passenger window , and the lower right switch controls the right rear passenger window . The switche[...]

Auto Down Feature — If Equipped The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down auto- matically . T o open the window part way , press the window switch part way and release it when you want the window to stop. Power Rear Windows The re[...]

windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunr oof open, adjust the sunroof opening to minimize the buffeting. REAR SWING GA TE The swing gate can be unlocked using the r emote keyless entry , or by activating the power[...]

W ARNING! T o avoid injury stand back when opening. Glass will automatically rise. The vacuum fluor escent (VF) display located in the odometer area displays the wor ds “GA TE” and/or “GLASS” as an indication of when the swing gate and/or flip-up window , is not completely closed. When the vehicle is not moving and the swing gate and/or fli[...]

If any other active warnings including “door” are present, they will be shown in the VF display and will also continue to cycle. If the vehicle is moving, two single chimes will occur if the rear glass is open or three single chimes will occur if the rear swing gate is open (one chime for each complete display cycle). After this, the VF display[...]

W ARNING! Driving with the flip-up window open can allow poisonous exhaust gases into your vehicle. Y ou and your passengers could be injured by these fumes. Keep the flip-up window closed when you are operating the vehicle. NOTE: The rear swing gate will lock while the rear wiper is operating. The gate will stay locked until the wiper is turned of[...]

W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly . Buckle up even though you are an excellent driver [...]

The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of you striking the inside of the vehicle or being thrown out. W ARNING! • W earing a seat belt incorre[...]

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door . Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. Latch Plate THINGS TO KNOW BEFORE ST [...]

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is[...]

4. Position the lap belt across your thighs, below your abdomen. T o remove slack in the lap portion, pull up a bit on the shoulder belt. T o loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. NOTE: The “Seat Belt Indicator Light” will rem[...]

W ARNING! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug. A twisted belt cannot do its job as well. In a collision it could even cut into you. Be sure the [...]

Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the 65% rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. NOTE: • If the rear center lap/shoulder belt cannot be pulled out, check that the r[...]

the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place. W ARNING! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase [...]

When T o Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. How T o Use The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the [...]

W ARNING! • After a vehicle collision, the driver and front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all seat belts should be checked for proper function. • The belt and retractor assembl[...]

Enhanced Seat Belt Use Reminder System (BeltAlert) If the driver’s or front passenger seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also [...]

4. T urn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced W arning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced W arning System (BeltAlert) has been deactivated, the Seat Belt W arning Light will continue [...]

W ARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags This veh[...]

the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multi stage inflator design. This may allow the airbag to have different rates of inflation that are based on collis[...]

W ARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. Y ou may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating. • If your vehicle is equipped with[...]

If your vehicle is so equipped, the window bag on the crash side of the vehicle is triggered in moderate to severe side collisions. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly . Here are some simple steps you can take to minimize the risk of harm fr[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instru- ment panel during airbag de[...]

• Driver and Front Passenger Seat Belt Pretensioners • Front Passenger Seat Occupant Classification System (OCS) − Occupant Classification Module − Passenger Airbag Disabled (P AD) Indicator Light − Interconnecting W iring − Pressur e Sensor , Bladder Assembly , and Belt T ension Sensor How The Airbag System W orks • The Occupant Rest[...]

in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously . A single chime will sound if the light comes on again after initial start up. W ARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on[...]

the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the outside edge of the headliner out of the way and covers the window . The airbag inflates in about 30 milliseconds (about one quarter of the time it takes to blink your eyes) with enough force to injure you if you are[...]

grab handle) and AIRBAG warning light (located in the instrument cluster) are illuminated the airbag will be disabled. The ORC will not allow front airbag deployment in the event of a collision for occupants classified into the empty or child size categories. The P AD indicator light will illuminate indicating that the Passenger Airbag is OFF when [...]

should always use the P AD indicator light as an indica- tion if the front passenger is properly positioned or not. If the P AD indicator light comes on when an adult is in the passenger seat, have the passenger re-position them- selves in the seat until the light goes out. Remember , if the P AD indicator light is illuminated the passenger front a[...]

• The Passenger Airbag Disabled (P AD) Indicator Light indicates to the driver and passenger when the airbag is turned OFF . In the presence of a properly seated occupant, when the P AD indicator light is illuminated, the airbag is OFF . Also, when the Occu- pant Classification System detects either an empty seat or a weight less than the predete[...]

W ARNING! Unapproved modifications or service procedures to the front passenger seat assembly , its related compo- nents, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an acci- dent. A modified vehicle ma[...]

If A Deployment Occurs The airbag system is designed to deploy the airbags when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and front passenger , and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not me[...]

W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly , replaced by an authorized dealer as soon as possible. Also, have the Occupant Classification System serviced as well. Enhanced Accident Response System (E.A[...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right [...]

Airbag W arning Light Y ou will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free. If any of the following occurs, have an authorized dealer service the system promptly: • Does not come on during the 6 to 8 seconds after the ignition switch is first turned on. ?[...]

enough for an adult seat belt. Always check the child seat owner’s manual to ensure you have the right seat for your child. Use the restraint that is correct for your child: • This vehicle is not capable of accommodating the installation of a car bed used for carrying newborn babies at the right fr ont passenger seat position. If a car bed must[...]

cannot sit with knees bent over the seat cushion while the child’s back is against the seatback, they need a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) • For additional informatio[...]

Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you inst[...]

LA TCH — Child Seat Anchorage System (Lower Anchors and T ether for CH ildren) Y our vehicle’s rear seat is equipped with the child restraint anchorage system called LA TCH. The LA TCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages[...]

All three rear seating positions have lower anchorages that are capable of accommodating LA TCH-compatible child seats having flexible, webbing-mounted lower at- tachments. Child seats with fixed lower attachments must be installed in the outboard positions only . Regard- less of the specific type of lower attachment, NEVER install LA TCH-compatibl[...]

In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap. Forward- facing toddl[...]

downward into the seat, r emoving slack in the straps according to the child restraint manufacturer’s instruc- tions. W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when ins[...]

buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle arou[...]

W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Children T oo Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably , and whose legs are[...]

ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, con[...]

garage, and never sit in a parked vehicle with the engine running for a extended period. If the vehicle is stopped in an open area with engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspecte[...]

Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should feel the air directed against the windshield. Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 M i r r o r s ............................... 8 1 ▫ Inside Day/Night Mirror ................. 8 1 ▫ Automatic Dimming Mirror — If Equipped .... 8 2 ▫ Outside Mirrors ....................... 8 2 ▫ Exterior Mirrors Folding Feature ........... 8 3 ▫ Power Remote Control Mirrors — [...]

▫ Front Seat Adjustment — Recline .......... 1 0 9 ▫ 6–W ay Driver’s Power Seat W ith Manual Recliner ...................... 1 1 0 ▫ Head Restraints ...................... 1 1 1 ▫ Heated Seats — If Equipped ............. 1 1 2 ▫ 65/35 Split Folding Rear Seat ............. 1 1 3 䡵 T o Open And Close The Hood ............. 1 1 5 ?[...]

▫ T o Set At A Desired Speed ............... 1 2 4 ▫ T o Deactivate ........................ 1 2 4 ▫ T o Resume Speed ..................... 1 2 4 ▫ T o V ary The Speed Setting ............... 1 2 4 ▫ T o Accelerate For Passing ............... 1 2 5 䡵 Electronic Brake Control System ............ 1 2 5 ▫ ABS (Anti-Lock Brake System) ...[...]

䡵 Power Outlet .......................... 1 5 0 䡵 Cup Holders .......................... 1 5 2 ▫ Smoker’s Package — If Equipped .......... 1 5 3 䡵 Cargo Area Features ..................... 1 5 4 ▫ C a r g o L i g h t ......................... 1 5 4 ▫ Retractable Cargo Area Cover — If Equipped ......................... 1 5 4 ▫ Ca[...]

MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . Annoying headlight glare from vehicles behind you can be reduced by moving the small control under the mirr or to the night position (toward rear of vehi[...]

Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. Y ou can turn the feature on or off by pressing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirror during cleaning, n[...]

W ARNING! V ehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger sid[...]

Set the top switch to the left or right for the left or right mirror , and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror . Press one of the four arrows for the direction you want the mirror to move. Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt f[...]

When the ignition is turned off, the light will turn off automatically (after approximately 8 minutes). Sun V isor Extension — If Equipped This feature has a pull out extension on the sun visor for increased coverage. HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications[...]

The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free profile cellular phone. UConnect™ features Bluetooth™ technology - the global standard that enables different elect[...]

Headset Profile), you may not be able to use any UCon- nect™ features. Refer to your cellular service provider or the phone manufacturer for details. The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can be adjusted either from the radio volume control knob, or from the steering whe[...]

V oice Command T ree Refer to “V oice T ree” at the end of this section. Help Command If you need assistance at any prompt, or if you want to know your options are at any prompt, say ⬙ Help ⬙ follow- ing the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. T o activate the UConnect™ system[...]

The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing ⬙ and follow the audible prompts. • When prompted, after the voice on beep, say ⬙ Pair a Phone ⬙ and follow the audible prompts. • Y o[...]

• System will prompt you to say the number you want call. • For example, you can say ⬙ 234-567-8901. ⬙ • The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios. Call/Dial by Saying a Name • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and[...]

• When pr ompted, say the name of the new entry . Use of long names helps the voice recognition and is recom- mended. For example, say ⬙ Robert Smith ⬙ or ⬙ Robert ⬙ instead of ⬙ Bob. ⬙ • When prompted, enter the number designation (e.g., ⬙ Home, ⬙⬙ W ork, ⬙⬙ Mobile, ⬙ or ⬙ Pager ⬙ ). This will allow you to store mul[...]

After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙ Phonebook Edit ⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may ha[...]

Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Erase All. ⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be del[...]

Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. T o reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incomi[...]

indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in progr ess (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Three-W [...]

Call Continuation Call continuation is pr ogression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or[...]

Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ [...]

Please refer to the 24-Hour “T owing Assistance” cover- age details in the W arranty information booklet and on the 24–Hour T owing Assistance Card. Paging T o learn how to page, refer to ⬙ W orking with Automated Systems. ⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with[...]

Barge In - Overriding Prompts The ’V oice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately . For example, if a prompt is playing ⬙ W ould you like to pair a phone, clear a ѧ , ⬙ you could press the ’V oice Recognition’ button and say ⬙ Pair a Phone ⬙ to sele[...]

NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number , the user may feel that the call did not go through even though the call is in progr ess. Once your call is answered, you will hear the [...]

Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Y our cellular phone can be paired with many differ ent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone[...]

• Y ou can also press the ⬘ V oice Recognition’ button anytime while the list is being played, and then choose the phone that you wish to select. • The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (appr[...]

• Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work fo[...]

• smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity , echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth [...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 105 3 I n f o r m a t i o n P r o v i d e d b y :[...]

106 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 107 3 I n f o r m a t i o n P r o v i d e d b y :[...]

North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up [...]

Using body pressur e, move forward and rearwar d on the seat to be sure the seat adjusters have latched. W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle i[...]

W ARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 6–W ay Driver’s Power Seat with Manual Recliner The seat switch is on the outboard side of [...]

This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear . Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head re[...]

Heated Seats — If Equipped The heated seat switch is located on the outboard side of the front seats. Pressing this switch to its desired setting (HI or LO) will activate the respective heating element for the heated seat. Once the heated seat switch is activated, depressing it a second time will de-activate it. W ARNING! Persons who are unable t[...]

65/35 Split Folding Rear Seat T o provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room. NOTE: Prior to folding the rear seat, it may be necessary to reposition the front seat to it’s mid-track position. Also, be sure that the front seats are fully upright an[...]

T o fold the 65/35 rear seat, perform the following steps: 1. Locate the seatback release handle on the outboar d top side of each rear seatback; lift up on the handle, and rotate the lever forward until the seatback releases. Fold the seatback completely forward. NOTE: When lifting up on the release handle, the seatback will release easier if you [...]

T o restore the 65/35 rear seat to the upright position perform the following steps: Raise the seatback and lock it into place. If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. The seat release handle will be flush with the seatback when the seat is ful[...]

Then, reach under the hood and slide the safety latch to the right and lift the hood. T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 inches (30 cm) and then push hood closed. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches e[...]

LIGHTS Multi-Function Control Lever The multi-function control lever controls the operation of the park lights, headlights, headlight beam selection, passing light, fog lights, instr ument panel light dimming, and turn signals. Battery Saver Feature — Exterior Lights If the park lights, headlights, fog lights, or high beams are left on when the i[...]

Instrument Panel and Interior Lights When the multi-function control lever is in the parklight, or headlight position, rotating the center portion of the lever up and down will increase and decrease the bright- ness (dimmer control) of the instrument panel lights. Full daytime brightness on all electronic displays (odometer , overhead console, radi[...]

T urn Signals Move the multi-function control lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Y ou can signal a lane change by moving the lever partially up or down without moving beyond the detent. If either light flashes at a very fast rate, check for [...]

Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. T o turn these lights off, press the recessed ar ea of the lens a second time. WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . This control lever is l[...]

Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it ente[...]

TIL T STEERING COLUMN T o tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Pull the lever back towards you and firmly push the lever until it is above the lower surface of the shroud to lock the column in place. T ilt Steering Column 122 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n[...]

W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL When engaged, this device takes over accelerator opera-[...]

T o Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, or pressing the CANCEL button will deactivate the Speed Control without erasing the memory . Pressing t[...]

T o Accelerate for Passing Depress the accelerator as you would normally . When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. (If the vehicle speed drops b[...]

ABS (Anti-Lock Brake System) This system aids the driver in maintaining vehicle contr ol under adverse braking conditions. The system controls hydraulic brake pressur e to prevent wheel lock-up and help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in Section 5 of this manual for more information about AB[...]

TCS (T raction Control System) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressur e is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability . A featur e of the TCS system functions similar to a limited slip differential and contr[...]

W ARNING! BAS (Brake Assist System) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slippery surfaces, or hydro- planing. Only a safe, attentive, a[...]

W ARNING! Many factors, such as vehicle loading, road condi- tions and driving conditions, influence the chance that wheel lift or rollover may occur . ERM can not prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent acci[...]

ESP/TCS Indicator Light The ⬙ ESP/TCS Indicator Light ⬙ located in the instrument cluster , starts to flash as soon as the tires lose traction and the ESP system becomes active. The ⬙ ESP/TCS Indicator Light ⬙ also flashes when TCS is active. If the ⬙ ESP/TCS Indicator Light ⬙ begins to flash during acceleration, ease up on the accelera[...]

High Range (4WD Part T ime, 4WD Full T ime) or 2WD Models ESP On This is the normal operating mode for ESP in 2WD, 4WD Part T ime, 4WD Full T ime (Selec-T rac Only), and on 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD low range or neutral back to 4WD high range or 2WD, the ESP system will be i[...]

NOTE: T o improve the vehicle’s traction when driving with snow chains, or starting off in deep snow , sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP switch. Once the situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily depressing the “[...]

several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • ⬙ The ⬙ ESP/TCS Indicator Light ⬙ and the ⬙ ESP/BAS W arning Lamp ⬙ come on momentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP Sy[...]

NOTE: T emperature accuracy can be effected from heat soak. For best accuracy , the vehicle should be driven at a speed greater than 20 mph (32 km/h) for several minutes. Dome/Reading Lights Located in the overhead console are two dome/reading lights. The dome/reading lights illuminate when a door or the swing gate is opened or when the interior li[...]

Electronic V ehicle Information Center The electronic vehicle information center (EVIC), when the appropriate conditions exist, displays the following messages and symbols. Each message is accompanied by a series of beeps: • DRIVER DOOR OPEN • P ASSENGER DOOR OPEN • N DOORS OPEN (N = 2, 3, 4) • RIGHT REAR DOOR OPEN • REARGA TE OPEN • LE[...]

Customer Programmable Features Press the MENU button until one of the display choices following appears: Language? When in this display you may select one of five lan- guages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display to select English, Francais, Deutsch, Italiana, or Espanol. As[...]

ALL DOORS. This can also be pr ogrammed using the key fob, refer to “Remote Keyless Entry” earlier in this section. T rain Remote? Pressing the STEP button when in this display will select “Y es” or “No.” NOTE: Any time you perform this procedure, it is necessary to retrain all currently trained key fobs. T o T rain Additional Key Fobs [...]

Flash Lights W ith Locks? When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked using the remote keyless entry transmitter . This feature may be selected with or without the sound horn on lock feature selected. Pressing the STEP button when in this display will select “Y es” or “No.”[...]

Mini-T rip Computer This feature, located in the overhead console, displays information on outside temperature, compass direction, and trip information. Reset Button Use this button to reset the A verage Economy , T rip Miles, and T ime Elapsed displays. This will occur only if a resettable function is currently being displayed (A verage Economy , [...]

W ARNING! Even if the display still reads a few degrees above 32°F (0°C), the road surface may be icy , particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage. Step Button Press the STEP button to cycle through all of the displays. The displays are: A ver[...]

T ire PSI Shows the pressur e and location of each tire, except for the spare tire. The tire location will blink when under pressur e. Blank Screen Shows a blank screen. Pressing the C/T button returns to the Compass and T emperature display . Pr essing the STEP button returns you to the A verage Miles per Gallon display . Automatic Compass Calibra[...]

T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Press and hold the RESET button five seconds (no more than 10 seconds). The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation. General Information This [...]

CAUTION! Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate this equipment. GARAGE DOOR OPENER — IF EQUIPPED Equipped in vehicles that have the optional Electronic V ehicle Information Center (EVIC) The HomeLink 威 W ireless Control System provides a convenient [...]

Retain the original transmitter of the RF device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. T o erase the programmed buttons, perform the procedur e shown below under ⬙ When Y our [...]

Programming HomeLink NOTE: It is recommended that a new battery be placed in the hand-held transmitter of the device being pro- grammed to HomeLink for quicker training and accurate transmission of the radio frequency signal. 1. Position the end of your hand-held transmitter 1-3 inches (5-14 cm) away from the lower left corner of the EVIC display w[...]

4. Press and hold the just-trained HomeLink button. TRANSMIT should appear on the display . If your device activates when the HomeLink button is depressed and released, programming is complete. NOTE: T o program the remaining two HomeLink but- tons, simply repeat the ⬙ Programming HomeLink ⬙ pro- cess. If the message TRANSMIT appears on the Hom[...]

If, after programming the HomeLink Wireless Control System, the hand-held transmitter and/or other HomeLink units in other vehicles fail to activate the rolling code equipped device, you may need to clear (or ⴖ erase ⴖ ) the device’s receiver memory . Refer to your garage door opener’s Owner’s Manual for the proce- dure or contact HomeLin[...]

Using HomeLink T o operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener , gate operator , security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there[...]

Press and hold the “V” button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. T o close the sunroof fr om the vent position, pr ess and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent[...]

W ARNING! • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. Y ou could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. • Do not allow small children to operate the sun- roof. Never allow fingers or other body parts, or [...]

There is a r ear power outlet located in the right rear cargo area above the storage cargo net/CD changer (if equipped). The rear power outlet is a direct feed from the battery so it receives power whether the ignition is in the ON or OFF position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in[...]

CAUTION! Electrical Outlet Use W ith Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories [...]

Smoker’s Package — If Equipped W ith the optional Smoker’s package, a removable ash tray is inserted into the front cup holder location. The rear passengers have access to a cup holder on each rear door trim panel. Rear Cup Holders UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 153 3 I n f o r m a t i o n P r o v i d e d b y :[...]

CARGO AREA FEA TURES Cargo Light The cargo area light is activated by opening the swing gate, opening any door , or by r otating the dimmer contr ol on the multi-function control lever to the extreme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens surface will turn off all interior lights. Push[...]

W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. Cargo Tie-Down Hooks Th[...]

W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center[...]

REAR WINDOW FEA TURES Rear Window Wiper/W asher A rotary ring switch on the control lever , located on the right side of the steering column, controls operation of the rear wiper/washer function. Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the wiper . Rotating the switch ring beyond the ON or OF[...]

Rear Window Defroster On the top of the climate control panel is a push button for r ear window defrosting. An amber indicator in the push button will light when the defroster is turned on. Push again to turn off the defroster prior to an automatic time-out. The defroster will automatically turn off after about ten minutes. For about five more minu[...]

ROOF LUGGAGE RACK External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the rated vehicle capacity as shown on the label attached to the drivers door shut face. CAUTION! • T o avoid damage to the roof rac[...]

W ARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack. 160 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel And Controls ............. 1 6 4 䡵 Instrument Cluster ...................... 1 6 5 䡵 Instrument Cluster Description ............. 1 6 6 䡵 Electronic Digital Clock .................. 1 7 6 ▫ Clock Setting Procedur e................. 1 7 6 䡵 Radio General Information ......[...]

▫ Radio Operation ...................... 1 8 4 ▫ CD Player Operation ................... 1 8 7 䡵 Sales Code RB1 — AM/FM Stereo Radio W ith DVD/GPS Navigation System .............. 1 9 1 ▫ Clock Setting Procedur e................. 1 9 2 䡵 6–Disc Remote CD Changer — If Equipped .... 1 9 4 ▫ Loading The CD Changer ............... 1 9[...]

▫ CD Player — 6 Disc In Cargo Area ......... 2 0 1 䡵 CD/DVD Disc Maintenance ............... 2 0 2 䡵 Radio Operation And Cellular Phones ........ 2 0 2 䡵 Climate Controls ....................... 2 0 3 ▫ Manual Air Conditioning And Heating System 203 ▫ Operating T ips ....................... 2 0 5 UNDERST ANDING YOUR INSTRUMENT P ANEL [...]

INSTRUMENT P ANEL AND CONTROLS 164 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER UNDERST ANDING YOUR INSTRUMENT P ANEL 165 4 I n f o r m a t i o n P r o v i d e d b y :[...]

INSTRUMENT CLUSTER DESCRIPTION 1. T achometer Indicates the permissible engine revolutions-per-minute for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 2. T urn Signal Indicator Light The arrows will flash in unison with the exterior turn signals, when using the multi-function control lever . A [...]

and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under- inflated tir e causes the tir e to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability . Please note that the TPMS is n[...]

7. Fog Light Indicator Light — If Equipped This light shows when the front fog lights are on. 8. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD II which monitors engine and auto- matic transmission control systems. This light will illuminate when the ignition is in the ON position before engine start. If[...]

If the ABS light is on, the brake system should be serviced as soon as possible to restor e the benefit of Anti-Lock Brakes. The operation of the ABS light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately four seconds. The light should then turn off unless a brake [...]

holding the button in resets the trip odometer . Also, pressing the “Reset” button will clear out any warning messages in the odometer display . 13. Odometer/T rip Odometer A vacuum fluorescent display indicates the total distance the vehicle has been driven. Also, the cluster will display , replacing the odometer/trip odometer , vehicle warnin[...]

If the warning light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERA TE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. Also, a single chime will sound. 16. T ransmission T emperature W arning Light This light indicates that there is excessive trans- mission fluid temperature that might occur with severe usag[...]

W ARNING! Driving a vehicle with the BRAKE warning light on is dangerous. A significant decrease in braking per- formance or vehicle stability during braking may occur . It will take you longer to stop the vehicle or will make your vehicle harder to control. Y ou could have an accident. Have the vehicle checked immedi- ately . The operation of the [...]

21. Fuel Gage When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. A small arrow indicates the side of the vehicle where the filler cap (gas cap) is located. 22. Low Fuel W arning Light When the fuel level reaches approximately 2.3 U.S. Gallons (8.7 Liters) this light will come on and rema[...]

26. Electronic Throttle Control (ETC) W arning Light — If Equipped This light informs you of a problem with the Electronic Throttle Control System. If a prob- lem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the vehicle is safely and completely [...]

27. Electronic Stability Program (ESP) W arning Light/Brake Assist System (BAS) W arning Light — If Equipped The ESP/BAS warning light in the instrument cluster comes on when the ignition switch is turned to the “ON” position. The light should go out with the engine running. If the ESP/ BAS warning light comes on continuously with the engine [...]

ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping i[...]

Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such [...]

Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in [...]

stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and F ADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bas[...]

1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion. NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE:[...]

Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the pr evious selection if the CD is within the first second of the current selection. EJT — Eject Press the EJT button and the disc will unload and move to the e[...]

Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA T” will appear in your radio display . A CD or tape may remain in the player while in the Satellite mode. Ti m e Press the TIME button to change the display from elapsed CD playing time to time of day . CD Changer Control Capability — If Equipped This radio is c[...]

Random Play (RND) Press the Random button to play the tracks on the selected disc in random or der for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s [...]

SALES CODE RBQ—AM/FM STEREO RADIO W I T H6-D I S CC D CHANGER NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the i[...]

channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs. CD’s may remain in the player while in the Satellite Radio mode. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and th[...]

Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and F ADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the T reble tones. Press the AUDIO butto[...]

CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / V olume control pushed ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3 ⁄ 4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Y ou may either insert or eje[...]

Radio display will show “ejecting” when it is being ejected. If you have ejected a disc and have not r emoved it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD. If the CD is r emove[...]

PTY (Program T ype) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button repeatedly within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information. T oggle th[...]

Program T ype Radio Display Ta l k Ta l k T op 40 T op 40 W eather W eather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type w[...]

A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. CD ERROR will appear on the display if the laser is unable to read the Disc data for the following reasons: • W arped disc • Excessive vibration • Disc inserted upside d[...]

variety of destinations and routes. Refer to your “Navi- gation User’s Manual” for detailed operating instruc- tions. NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Naviga- tion system and the CD Player simultaneously . Always remove the Navigation DVD before inserting another disc. Clock Set[...]

2. At the Clock Setup screen highlight the box next to “T ime Zone” and press ENTER. 3. Highlight the appropriate time zone for you location and press ENTER to store your selection. 4. Select “Done” when finished. NOTE: When you are traveling and enter a new time zone, the clock must be reset manually for the new zone. Changing Daylight Sav[...]

6–DISC REMOTE CD CHANGER — IF EQUIPPED Loading the CD Changer Removing the CD Changer Magazine NOTE: Always keep the CD changer door closed except when ejecting or installing the magazines. The door is designed to keep dust, dirt, and foreign objects out of the CD changer . Handle the magazine with reasonable care. The magazine may crack if dro[...]

4. Close the CD changer door by sliding it to the left. Loading Discs into the Magazine Gently pull out a tray from the magazine, and place the disc with the label as indicated on the top of the magazine (up to 6 discs). Slide the tray into the magazine until it locks in place. Do not remove the trays from the magazine. If the discs are installed u[...]

System Activation T o activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www .sirius.com. Please have the following informa- tion available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Y our V ehi[...]

mode when any other button is pushed, the ignition is turned OFF , or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙ SA ⬙ appears in the display . A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP[...]

NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-539- 7474 to discuss options for channel blocking or unblock- ing. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stat[...]

Satellite Antenna T o ensure optimum reception, do not place items on the roof around the r ooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger lug- gage items such as bikes should be placed as far re[...]

REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls ar e located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a push-button in the center and controls the volume and mode of the sound system. Pressing the top of the rocker swit[...]

Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station. The button located in the center of the left hand control will tune to the next preset station that you have pro- grammed in the radio preset push-button. T ape[...]

If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc in the 6–disc magazine. CD/DVD DISC MAINTENANCE T o keep the CD/DVD discs in good condition, take the following precautions: 1. Han[...]

CLIMA TE CONTROLS Manual Air Conditioning and Heating System The controls for the heating, air conditioning, and venti- lation system in this vehicle consist of a series of rotary knobs, and a push-button. These comfort controls can be set to obtain desired interior conditions. Blower Control The rotary knob on the left controls the blower and can [...]

normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy . Mode Control The mode selector (the center rotary knob and the push-button above it) can be set in any of the following positions: OFF This position turns off the blower motor and outside air will not pass through any outlets. Recirculate (Max [...]

enabled in Floor mode to provide less humid air , espe- cially when heat is used. This will help you reduce or prevent window fogging in high humidity conditions. This function cannot be disabled. Y ou may still select the desired amount of heat using the temperatur e control dial. The heated air will simply be drier and less prone to condensing on[...]

smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. W inter Operation When operating the system during the winter months, make sure the air intake, located directly in front of the windshield, is free of ice, slush, snow , or other obstr uctions. V acation Storage Anytime you store your vehicle, or[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es ..................... 2 1 1 ▫ Manual T ransmission .................. 2 1 1 ▫ Automatic T ransmission ................ 2 1 1 ▫ Normal Starting ...................... 2 1 2 ▫ Extreme Cold W eather (Below –20°F (–29°C) . . 212 ▫ If Engine Fails T o Start ................. 2 1 [...]

▫ Shifting Procedur e .................... 2 2 8 ▫ Selec-T rac 威 Operating Information/Precautions — If Equipped ......................... 2 2 9 ▫ Shift Positions ........................ 2 3 2 ▫ Shifting Procedur e .................... 2 3 2 䡵 T rac-Lok™ Rear Axle — If Equipped ......... 2 3 4 䡵 On-Road Driving T ips ..........[...]

▫ T i r e S p i n n i n g ........................ 2 5 7 ▫ T read W ear Indicators .................. 2 5 7 ▫ L i f e O f T i r e ......................... 2 5 8 ▫ Replacement T ires ..................... 2 5 9 ▫ Alignment And Balance ................. 2 6 0 䡵 T ire Chains ........................... 2 6 0 䡵 T ire Rotation Recommendat[...]

䡵 T r a i l e r T o w i n g ......................... 2 8 2 ▫ Common T owing Definitions ............. 2 8 2 ▫ T railer Hitch Classification ............... 2 8 6 ▫ T railer T owing W eights (Maximum T railer W eight Ratings) ......... 2 8 7 ▫ T railer And T ongue W eight .............. 2 8 9 ▫ T owing Requirements .................. 2 [...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. W AR[...]

NOTE: This vehicle is equipped with a transmission shift interlocking system. The brake pedal must be depressed to shift out of Park (P). Normal Starting Normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. T urn the key to the ST AR T position and release when the engine starts. If the [...]

If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! T o prevent damage to the starter , do not cr[...]

W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cannot be started this way . Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be used [...]

CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death. [...]

MANUAL TRANSMISSION Clutch Interlocking Ignition System 2WD Models Only — Manual transmission vehicles are equipped with a clutch interlock safety feature. The clutch pedal must be fully depressed to allow cranking of the engine. 4WD Models Only — The exception to this clutch inter- lock is 4WD models equipped with a manual transmis- sion. For [...]

W ARNING! When parking your vehicle, always leave a manual transmission in first gear and apply the parking brake fully to guard against vehicle movement and possible injury or damage. Never use any gear as a substitute for the parking brake. CAUTION! T o drive as safely as possible and to prolong the life of your manual transmission, follow these [...]

• Do not operate at sustained high engine or r oad speeds in lower gears. Engine damage may result. • Do not downshift into a low gear while traveling at too high a speed for that gear . Engine, clutch, or transmis- sion damage may result. • Do not rest your foot on the clutch pedal. This causes heat buildup and damages the clutch. • When y[...]

Recommended Manual T ransmission Downshifting Speeds T o prevent clutch and transmission damage, your vehicle should be downshifted at speeds no greater than those listed in the chart below: Manual T ransmission Downshift Speeds in MPH (KM/H) Gear Selec- tion 6th to 5th 5th to 4th 4th to 3rd 3rd to 2nd 2nd to 1st Maxi- mum Speed 90 mph (144 km/h) 7[...]

AUTOMA TIC TRANSMISSION — IF EQUIPPED CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift into P (Park) only after the vehicle has come to a complete stop. • Shift into or out of R (Reverse) only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift f[...]

Automatic T ransmission with Overdrive Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears. Gear Ranges P (Park) This gear position supplements the parkin[...]

W ARNING! It is dangerous to shift the selector lever out of P (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. Y ou could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is id[...]

• V ehicle speed is above approximately 30 mph (48 km/h). • T ransmission has reached normal operating tempera- ture. When frequent transmission shifting occurs while using Overdrive, such as when operating the vehicle under heavy load conditions (for example, in hilly terrain, strong head winds, or trailer towing), turning off over- drive will[...]

time restores the Overdrive function. The lockout feature is useful when towing a trailer or carrying a heavy load. NOTE: If the vehicle is started in cold outside tempera- tures, shifts into Overdrive may be delayed. Normal Overdrive and shifting operation will resume when the temperature of the transmission reaches the appropriate temperature. Re[...]

Over T emperature Mode The transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may r esult in a slightly differ ent feeling or response during normal operation in D (Drive) position. If the transmission beco[...]

normal condition and will not cause damage to the transmission. The torque converter will refill within 5 seconds of shifting from P (Park) into any other gear position. FOUR-WHEEL DRIVE OPERA TION Command-T rac 姞 Operating Information/Precautions The Command-T rac 威 transfer case provides 4 mode position s-2( r ear) wheel drive high range, 4-w[...]

CAUTION! • Do not attempt to make a shift while only the front or rear wheels are spinning. The Command- T rac transfer case is not equipped with a synchro- nizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer [...]

Shift Positions For additional information on the appropriate use of each transfer case mode position see the information below: 2H Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4H 4-Wheel-Drive High Range - Locks the front and rear driveshafts together . Forces the front and rear wheels to rotate at the [...]

4H to 4L or 4L to 4H W ith the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission. While the vehicle is coasting at 2 to 3 mph (3 to 5 km/h), shift the transfer case lever firmly to the desired position. Do not pause in transfer case N (Neutral). NOTE: T o shift[...]

including dry hard surfaced roads. The 4 FULL TIME mode allows the front and rear wheels to rotate at differ ent speeds which eliminates driveline binding and component wear that is normally associated with driving the vehicle in the 4 P AR T TIME position on dry hard surfaced roads. This feature provides the safety , security , and convenience of [...]

CAUTION! • Do not attempt to make a shift while only the front or rear wheels are spinning. The Selec-T rac transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case.[...]

Shift Positions For additional information on the appropriate use of each transfer case mode position see the information below: 2WD Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4 P AR T TIME Part T ime 4–Wheel Drive High Range - Locks the transfer case inter-axle differential. Forces the fr ont and re[...]

accelerator pedal may be r equired after shifting. This will induce a torque interrupt and allow full engagement of the newly selected position. W ith the vehicle stationary it may be necessary to shift the automatic transmission from D (Drive) to R (Reverse) and back to D (Drive) after shifting. This will allow full engagement of the newly selecte[...]

completing the shift. If difficulty occurs, shift transmis- sion to N (Neutral), hold foot on brake, and turn engine OFF . Make shift to desired mode. NOTE: Shifting into or out of 4LO is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be re[...]

W ARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance and a narrower track to make them capable o[...]

Driving Through W ater Although your vehicle is capable of driving through water , there are a number of precautions that must be considered before entering the water: CAUTION! When driving through water , do not exceed 5 mph (8 km/h). Always check water depth before entering as a precaution, and check all fluids afterward. Driving through water ma[...]

Maintenance After driving through deep water , inspect your vehicle fluids and lubricants (engine oil, transmission oil, axle, transfer case) to assure the fluids have not been contami- nated. Contaminated fluid (milky , foamy in appearance) should be flushed/changed as soon as possible to pre- vent component damage. Driving In Snow , Mud and Sand [...]

W ARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. T o do so may result in tipping and rolling the vehicle. Always back care- fully straight down a hill in R (Reverse) gear . Never back down a hill in N (Neutral) using only the brake. Remember , never drive diagona[...]

• Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage. • Check thr eaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and sus- pension. Retighten them, if requir ed, and torque to the values specified in the Service Manual. ?[...]

P ARKING BRAKE T o set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake W arning Light” in the instru- ment cluster will light. T o release the parking brake, pull up slightly , press the center button, then lower the lever completely . NOTE: The instrument cluster ?[...]

W ARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury . Also, be certain to leave an automatic trans- mission in P (Park), a manual transmission in R (Reverse) or 1st gear . Failure to do so may allow the vehicle to roll and cause damage or injury . • Leaving children in a vehicle [...]

W ARNING! Significant over or under-inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The Anti-Lock Brake System conducts a low speed self- test at about 12 mph (20 km/h). If for any reason, your foot is on the brake when the vehicle reaches 12 mph (20 km/h), this check will be delayed [...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. NOTE: Increased noise levels at the end of the steering wheel travel are considered normal and [...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards. T ires designed to this standard have th[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ ....blank.... ⴖ = Passenger car tire based on European design standards LT = Light T ruck tire based on U.S. design standards T = T emporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section W idth in Milimeters (mm) 65 = Aspec[...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the T[...]

Tire Loading and Tire Pressure T ire Placard Location NOTE: The proper cold tire inflation pressur e for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar . For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door , the[...]

T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the t[...]

combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight refer enced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the[...]

252 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory op[...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire r olling resistance and results in higher fuel consump- tion. 3. Ride Comfort and V ehicle Stability—[...]

check tire pressur e. Do not make a visual judgement when determining pr oper inflation. Radial tir es may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which cou[...]

Tire Pressures for High Speed Operation The manufactur er advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressur e is very important. Increased tire pressur e and reduced vehicle loading may be requir ed for hi[...]

Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph [...]

These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or mor e adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon var[...]

Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph on tre[...]

CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment and Balance Poor suspension alignment may result in: • Fast tire wear . • Uneven tire wear , such as feathering and one-sided wear . • V ehicle pull to right or left. T ires may also cause the vehicle to pull left [...]

T ire chains that are recommended for this vehicle are listed below: • Mopar 威 P/N 82206828 with P235/70R16 and P235/ 65R17 tires. • Mopar 威 P/N 82207074 with P215/75R16 tires. NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement. Observe the tire chain manufacturer’[...]

NOTE: The Premium T ire Pressur e Monitor System will automatically locate the pressure values displayed in the correct vehicle position following a tire rotation. The suggested rotation method is the “forward-cr oss” shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressure Monitoring System (TPMS) will warn the dr[...]

The TPM System will warn the driver of a low tire pressur e if the tire pressur e falls below the low pressure warning threshold for any reason, including low tem- perature effects. The TPM System will continue to warn the driver of low tire pressur e as long as the condition exists, and will not turn off until the tire pressure is at or above reco[...]

Base System — If Equipped The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressur e readings to the Receiver Module. NOTE: It is particularly important, for you to check the tire pre[...]

The “T ire Pressure Monitoring T elltale Light” will flash on and off for 60 seconds, and an audible chime will sound when a system fault is detected. The flash cycle will repeat every ten minutes, without an audible chime, until the fault condition no longer exists. If the ignition key is cycled, this sequence will repeat, providing the system[...]

CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the T ire Pressure Monitoring Sensor . NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or conditi[...]

The T ire Pressur e Monitor System (TPMS) consists of the following components: • Receiver Module • 4 Wheel Sensors • V arious T ire Pressure Monitoring System Messages, which display in the Electronic V ehicle Information Center (EVIC). Refer to Section 4 of this manual. • T ire Pressur e Monitoring T elltale Light A tire pressure monitori[...]

Electronic V ehicle Information Center (EVIC) will display a “CHECK TPM SYSTEM” text message. The flash cycle will repeat every ten minutes, without an audible chime, until the fault condition no longer exists. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. NOTE: In the event that the matching[...]

• V arious T ire Pressure Monitoring System Messages, which display in the Electronic V ehicle Information Center (EVIC) • T ire Pressur e Monitoring T elltale Light A tire pressur e monitoring sensor is located in the spare wheel if the vehicle is equipped with a matching full size spare wheel and tire assembly . The matching full size spare t[...]

Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure. The system will automatically update, the graphic dis- play of the pressur e value(s) will stop flashing, and the “T i[...]

Light” will no longer flash, the ⬙ CHECK TPM SYSTEM ⬙ text message will no longer display , and a pressur e value will be displayed instead of dashes. NOTE: In the event that the matching full size spare tire is swapped with a low pressur e r oad tir e, the next ignition key cycle will still show the “T ire Pressure Monitoring T elltale Lig[...]

CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor . NOTE: • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPM[...]

FUEL REQUIREMENTS (GASOLINE ENGINES) Y our engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high quality unleaded gasoline having an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular [...]

Reformulated Gasoline Many areas of the country requir e the use of cleaner burning gasoline r eferred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality . The manufactur er supports the use of r eformulated gaso- lines. Properly blended [...]

to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recom- mends using gasolines without MMT . Since the MMT content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not his/her gasoline contains MMT . It is even more important to look for gasoline without[...]

• The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer . NOTE: Intentional tampering with emissions[...]

the vehicle is raised. Have any abnormal conditions repair ed promptly . Until repaired, drive with all side windows fully open. • Keep the swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. ADDING FUEL CAUTION! DO NOT put gasoline in your diesel vehicle (if equipped[...]

CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting after- market cap can cause the MIL (Malfunction Indica- tor Light) to illuminate, due to fuel vapors escaping from the system. CAUTION! A poorly[...]

NOTE: T ighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly , the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. W ARNING! A fire may result if gasoline is pumped into a portable contai[...]

W ARNING! • Never add fuel when the engine is running. • Never have any smoking materials lit in or near the vehicle when the fuel cap is removed or the tank filled. VEHICLE LOADING Certification Label As required by National Highway T raffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s s[...]

Each axle GA WR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for in- creased durability does not necessarily increase the vehi- cle’s GVWR. T ire Size The tir e size on the Label repr esents the actual[...]

within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally . Stow all loose items securely before driving. Improper weight distributions can have an adverse ef fect on t[...]

Gross T railer W eight (GTW) The gr oss trailer weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition. The recom- mended way to measure GTW is to put your fully loaded trailer on a vehicle scale. T[...]

Frontal Area The maximum height and maximum width of the fr ont of a trailer . T railer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically pr ovides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions[...]

W ARNING! An improperly adjusted W eight Distributing Hitch system may reduce handling, stability , braking per- formance, and could result in an accident. W eight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational V ehicle dealer for additional informat[...]

T railer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Y our vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional T railer T ow Prep Package. See your dealer for package content. The[...]

T railer Hitch Classification Class Max. GTW (Gross T railer Wt.) C l a s sI-L i g h t Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1 587 kg) Class III - Heavy Duty 5,000 lbs (2 268 kg) Class IV - Extra Heavy Duty 10,000 lbs (4 540 kg) All trailer hitches should be professionally installed on your vehicle. T railer T owing Weights (Max[...]

Engine/ T ransmission Model GCWR (Gross Com- bined Wt. Rating) Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. (See Note 1) 3.7L/6-Speed Manual 4x2 8,500 lbs (3 855 kg) 40 Sq. Ft. (3.72 square meters) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.7L/6-Speed Manual 4x4 8,750 lbs (3 969 kg) 40 Sq. Ft. (3.72 square meters) 3,500 lbs (1 587 kg) 3[...]

NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the T ire and Loading Information placard. Refer to the T ire– Safety Information section in this manual. T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the [...]

NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the T ire and Loading Information plac- ard in the T ire Safety Information section of this manual for the maximum[...]

W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou[...]

2. GTW 3. GA WR 4. T ongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressur es a[...]

actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − T railer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it shoul[...]

NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. [...]

If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while [...]

T owing T ips — Cooling System T o reduce potential for engine and transmission over- heating, take the following actions: − City Driving When stopped for short periods of time, put transmission in neutral and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning T urn off temporarily . − refer to Cooling System O[...]

(for automatic transmission) or into any forward gear (for manual transmission) for recr eational towing. Shifting Into Neutral (N) Use the following procedure to prepar e your vehicle for recr eational towing. CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (Neutral) before recreational towing to p[...]

CAUTION! T ransmission damage may occur if the automatic transmission is shifted into P (Park) with the transfer case in N (Neutral) and the engine running. W ith the transfer case in N (Neutral) ensure that the engine is OFF prior to shifting the transmission into P (Park) (refer to step s7–8 above). Shifting Out Of Neutral (N) Use the following[...]

CAUTION! Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. SNOW PLOW Snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structur e. The airbags could deploy unexpect- edly o[...]

I n f o r m a t i o n P r o v i d e d b y :[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flashers ................. 3 0 2 䡵 If Y our Engine Overheats ................. 3 0 3 䡵 Jacking And T ire Changing ................ 3 0 4 ▫ Jack Location ........................ 3 0 4 ▫ Spare T ire Stowage .................... 3 0 5 ▫ Preparations For Jacking ................ 3 0 5 [...]

HAZARD W ARNING FLASHERS Y our vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently . Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle. This is an emergency warning system, not t[...]

IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impen[...]

JACKING AND TIRE CHANGING W ARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never get any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack i[...]

Spare Tire Stowage T o remove the spare tire from the carrier , remove the tire cover , if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. NOTE: If you have added aftermarket accessories to the spare tire mounted carrier , it cannot exceed a gr oss weight of 50 lbs (23 kg) including the weight of the spare tire.[...]

• Block both the front and rear of the wheel diagonally oppo- site of the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove spare tire. 2. Loosen (but do not remove) the wheel lug nuts by turni[...]

5. Raise the vehicle by turning the jack scr ew to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability . W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could sl[...]

nuts until each nut has been tightened twice. Correct wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to it’s fully closed position. W ARNING! A loose tire or jack, thrown forward in a collision or ha[...]

W ARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other . If acid splashes in eyes or on skin, flush contaminated area immedi- ately with large quantities of water . A battery generates hydrogen gas whi[...]

5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery . Make sure you have a good contact on the engine. W ARNING! • Y ou should not try to start your vehicle by push- ing or towing. • Do not connect the cable to the negative post of the discharge batt[...]

EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, they are mounted in the front and the rear . CAUTION! T ow hooks are for emergency use only , to rescue a vehicle stranded of f road. Do not use tow hooks for tow truck hookup or highway towing. Y ou could damage your vehicle. T ow straps are recommended when tow- ing t[...]

4WD Models Only The manufacturer r ecommends towing with all four wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the other end on a towing dolly . 312 WHA T TO DO IN EMERGENCIES I n f o r m a t i o n P r o v i d e d b y :[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L ............... 3 1 6 䡵 Onboard Diagnostic System — OBD II ........ 3 1 7 ▫ Loose Fuel Filler Cap Message ............ 3 1 7 䡵 Emissions Inspection And Maintenance Programs ................... 3 1 8 䡵 Replacement Parts ...................... 3 1 9 䡵 Dealer Service ......[...]

▫ Driveline And Steering Component Lubrication .......................... 3 3 1 ▫ Body Lubrication ..................... 3 3 1 ▫ W indshield W iper Blades ................ 3 3 1 ▫ W indshield W ashers ................... 3 3 2 ▫ Exhaust System ...................... 3 3 3 ▫ Cooling System ....................... 3 3 3 ▫ Hoses And V ac[...]

▫ Rear T ail, Stop, T urn Signal, And Back-Up Lights ....................... 3 6 5 ▫ Center High Mounted Stop Light (CHMSL) . . . 365 䡵 Fluids And Capacities ................... 3 6 6 䡵 Fluids, Lubricants, And Genuine Parts ........ 3 6 7 ▫ Engine ............................. 3 6 7 ▫ Chassis ............................ 3 6 8 MAINT AIN[...]

ENGINE COMP ARTMENT – 3.7L 316 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly , your vehicle will provide excellent performance and fuel economy , as well[...]

the fuel filler cap properly to turn the message off (light will time out). If the problem continues, the message will appear the next time the vehicle is started. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could [...]

a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key [...]

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your ve[...]

CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions as well as your kind of driving af fect the interval at which your oil should be changed. Check the following to determine if any apply to you: • Day or night temperatures are below 32°F[...]

Engine Oil Selection For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Cer- tified and meet the requir ements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that[...]

Materials Added T o Engine Oils The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used en[...]

Special tools are requir ed to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled a[...]

Catalytic Converter The catalytic converter requires the use of unleaded fuel only . Leaded gasoline will destroy the ef fectiveness of the converter as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assure prope[...]

W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn. In unusual situations involving grossly malfunctioning engine o[...]

Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly , replace it with a new valve. DO NOT A TTEMPT TO CLEAN THE OLD PCV V AL VE! Check ventilation hose for i[...]

T o determine the battery charge, check the battery test indicator (if equipped) on top of the battery . Refer to the illustration. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) posit[...]

Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. W ARNING! • Use only refrigerants and co[...]

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equip[...]

Driveline And Steering Component Lubrication U-joints (cardan joints) are sealed and do not requir e lubrication. Prop shafts, yokes, ball joints and other driveline and steering components may be provided with grease fittings for lubrication. Lubrication of these com- ponents at the intervals specified in the appropriate “Maintenance Schedule”[...]

A void using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side a[...]

Exhaust System The best protection against carbon monoxide entry into the vehicle body is a pr operly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect [...]

leaves, etc. If dirty , clean by gently spraying water from a garden hose vertically down the face of the A/C con- denser (if equipped) or the radiator core. Check the engine cooling system hoses for brittle rubber , cracking, tears, cuts, and tightness of connection at the coolant recovery bottle and radiator . Inspect the entire system for leaks.[...]

CAUTION! • Mixing of antifreeze/coolant other than the speci- fied HOA T antifreeze/coolant may result in de- creased corrosion protection and engine damage. If a non-HOA T antifreeze/coolant is introduced into the cooling system in an emergency , it should be replaced with the specified antifreeze/coolant as soon as possible. • Do not use plai[...]

Use only high purity water such as distilled or deionized water when mixing the water/antifreeze (coolant) solu- tion. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cordi[...]

Disposal of Used Engine Coolant Used Hybrid Or ganic Additive T echnology (HOA T) antifreeze/coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community . T o prevent ingestion by animals or children, do not store HOA T antifreeze/coolant in open containers, or all[...]

If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check antifreeze/coolant freeze point in the system. • If frequent antifreeze/coolant additions are requir ed, or if the level in the recove[...]

Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure. Fuel System Connections Electronic Fuel Injection high pressure[...]

cuts, abrasion, and excessive swelling suggest deteriora- tion of the rubber . Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often fluids such as oil, power steering fl[...]

Brake Master Cylinder — Brake Fluid Level Check The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “Brake W arning Light” shows system failure. Be sure to clean the top of the master cylinder ar ea before removing the cap. If necessary , add fluid to bring the fluid level up to [...]

W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination fr om foreign matter . Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result. Clutch H[...]

T ransfer Case Fluid Level Check Inspect the transfer case for fluid leaks. If a fluid leak is evident, the transfer case fluid level can be checked by removing the fill plug (B) located at the back of the transfer case. The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position. Adding Fluid Only at f[...]

CAUTION! When installing plugs, do not overtighten. Y ou could damage them and cause them to leak. Selection of Lubricant Use only manufacturer’s recommended fluid, refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Manual T ransmission Selection of Lubricant Use only manufacturer’s recommended manual trans- mission fluid, r[...]

Automatic T ransmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufactur er’s recommended transmis- sion fluid, refer to Fluids, Lubricants, and Genuine Parts for corr ect fluid type. It is important that the transmission fluid be maintai[...]

T o check the automatic transmission fluid level properly , the following procedur e must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Apply the brakes and shift the transmission into P (Park). 5. The fluid MUST be checked with the t[...]

Maintenance After Off-Road Driving After extended operation in mud, sand or water , or similar dirty conditions, have your brake drums, brake linings, and axle joints inspected and cleaned as soon as possible. This will prevent any abrasive material from causing excessive wear or unpredictable braking action. After off-r oad driving, completely ins[...]

hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection. The following maintenance r ecommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint[...]

CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder , which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose of f the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the [...]

• If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use Mopar 威 T ouch Up Paint on scratches or chips as soon as possible. Y our authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome plated whee[...]

do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery . Application of a leather conditioner is not requir ed to maintain the original condition. W ARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may [...]

Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe c[...]

FUSE P ANEL Interior Fuses The fuse panel is on the left side of the instrument panel. A label is attached to the fuse panel cover to identify each fuse for ease of replacement. Cavity Fuse Description 1 15 Amp Blue Horn Relay , Power Sunroof Relay , Power W indow Relay 2 10 Amp Red Rear Fog Lights (Export Only) 3 20 Amp Y el- low Cigar Lighter 4 1[...]

Cavity Fuse Description 12 15 Amp Blue Stop Lights 13 10 Amp Red Body Control Module/CMTC/ Cluster/Pass. Airbag On,Off Indicator , Auto Daylight Mirror/Light Bar Switch (Ren- egade Only) 14 10 Amp Red PDC Fuel Pump/AC Clutch, Starter Relay/Engine Controller/T ransmission Con- troller (Diesel Only) 15 Spare 16 20 Amp Y el- low Power Outlet (Rear) 17[...]

Cavity Fuse Description 32 10 Amp Red W iper Switch/Front and Rear W ipers 33 10 Amp Red SKIM Module/Data Link Con- nector 34 15 Amp Blue Body Control Module/ Cluster/Interior Lights, Hands Free Module/Radio/CMTC/ ITM Module & Siren (Export Only) 35 Spare Cavity Fuse Description 36 10 Amp Red Airbag Control Module/ Occupation Classification Mod[...]

Underhood Fuses (Power Distribution Center) Y our vehicle is equipped with an electrical power distri- bution center located in the engine compartment near the battery . This power center houses plug-in “Cartridge” fuses which replace in-line fusible links. The power center also contains “Mini” fuses and plug-in full and micro ISO relays. A[...]

Power Distribution Center (Gasoline Engines) Cavity Fuse Description F1 40 Amp Green Blower Motor F2 40 Amp Green Radiator Fan F3 50 Amp Red JB Power F4 40 Amp Green ABS Pump F5 20 Amp Y el- low NGC T rans F6 30 Amp Pink ASD F7 50 Amp Red JB Power F8 40 Amp Green Ign/Start F9 50 Amp Red JB Power F10 30 Amp Pink T railer T ow F1 1 Open Cavity Fuse D[...]

Cavity Fuse Description F25 20 Amp Y el- low ABS V alves F26 25 Amp Natu- ral Injectors F27 Open F28 15 Amp Blue Starter R29 Half ISO Re- lay Fuel Pump R30 Half ISO Re- lay Starter R31 Half ISO Re- lay W iper On/Off R32 Half ISO Re- lay W iper Hi/Lo R33 Full ISO Relay H. Blower R34 Full ISO Relay Rad. Fan Hi Cavity Fuse Description R35 Half ISO Re-[...]

Power Distribution Center (Diesel Engines) Cavity Fuse Description F1 40 Amp Green Blower Motor F2 40 Amp Green Radiator Fan F3 50 Amp Red JB Power F4 40 Amp Green ABS Pump F5 Open F6 30 Amp Pink ASD F7 50 Amp Red JB Power F8 40 Amp Green Ign/Start F9 50 Amp Red JB Power F10 30 Amp Pink T railer T ow F1 1 20 Amp Y el- low Fuel Heater Cavity Fuse De[...]

Cavity Fuse Description F25 20 Amp Y el- low ABS V alves F26 25 Amp Natu- ral Injectors F27 Open F28 15 Amp Blue Starter R29 Half ISO Relay Fuel Heater R30 Half ISO Relay Starter R31 Half ISO Relay W iper On/Off R32 Half ISO Relay W iper Hi/Lo R33 Full ISO Relay H. Blower R34 Full ISO Relay Rad. Fan Hi Cavity Fuse Description R35 Half ISO Relay A/C[...]

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery . Y ou may: • Remove Cartridge fuse #15 in the Power Distribution Center labeled Ignition-Off Draw (IOD). • Store the removed IOD fuse in the Power Distribution Center location #1 1 labeled “IOD Storage.” • Or ,[...]

Exterior Lights Bulb T ype Front Side Marker ........................ 1 6 8 Headlights .......................... 9007QL Rear License Plate Light .................... 1 6 8 Rear Stop/T ail Lights ............... 3157 P27/7W Rear T urn Signal Lights (2) ......... 3757 APY27/7W NOTE: Numbers refer to commercial bulb types that can be purchased from y[...]

Front T urn Signal 1. Remove the screw from the turn signal/park lamp unit. 2. Pull the inboard side of the lamp away enough to disengage the tab that secures the outboard side of the lamp from the slot in the front bumper fascia. 3. Rotate the bulb socket counter-clockwise to unlock it. CAUTION! Do not touch the new bulb with your fingers. Oil con[...]

Front Fog Light (Front Fascia Mounted) 1. Remove the three screws from the backside of the lamp housing. 2. Pull the bezel and lens away from the lamp housing far enough to access and disconnect the wiring connector from the bulb pigtail wire. 3. Pinch together the two hooked ends of the bulb retainer clip and disengage them from the slots in the m[...]

Rear T ail, Stop, T urn Signal, and Back-Up Lights 1. Open the swing gate. 2. Remove the two T orx fasteners. 3. Remove rear lamp assembly . 4. Rotate the socket on the back of the lamp housing counter-clockwise to unlock it. 5. Replace the bulb. Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. T wist the bulb [...]

FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 20.5 Gallons 78 Liters Engine Oil with Filter 3.7 Liter Engines (SAE 5W -20, API Certified) 5 Qts 4.7 Liters Cooling System * 3.7 Liter Engine (Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula) 14 Qts 13.2 Liters * Includes heater and coolant recovery bottle filled to MAX level. 366 MAI[...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil (3.7L Engine) Use API Certified SAE 5W -20 Engine Oil, meeting the requir ements of DaimlerChrysler Material Standard MS-6395. Oil[...]

Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid Manual T ransmission Mopar 威 Manual T ransmission Lubricant or equivalent (meeting the re- quirements of DaimlerChrysler Material Standard MS-9224) T ransfer Case Mopar 威 A TF+4 Automatic T ransmission Fluid Axle Differ ent[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ........ 3 7 0 䡵 Maintenance Schedules ................... 3 7 0 ▫ Schedule “B” ........................ 3 7 3 ▫ Schedule “A” ........................ 3 8 5 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d b y :[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliabi[...]

• Off-r oad or desert driving NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow “Schedule B” of the “Maintenance Schedules” section of this manual. NOTE: If ANY of these apply to you then flush and replace your engine coolant/anti-freeze every 102,000 [...]

Once a Month • Check the tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as requir ed. • Check the fluid levels of the coolant reservoir , brake master cylinder , and transmission, and add as needed. • Check all lights and all other electrical items for corr ect operation. At Each[...]

Schedule “B” Follow this schedule if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Excessive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sust[...]

Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fluid. X 374 SCH[...]

Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs[...]

Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fluid. X Ins[...]

Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plug[...]

Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fluid[...]

Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark [...]

Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fluid[...]

Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace t[...]

Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fl[...]

Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change the engine oil and engine oil filter , if not replaced at 3 months. X X XXX Rotate the tires. X X Inspect the engine air filter element, replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spa[...]

Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. † Applies only if vehicle is used for frequent trailer towing or fleet/commercial service. 〫 This maintenance is recommended by the manufac- turer to the owner , but is not requir ed to maintain emissions warranty . ‡Off-high[...]

Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change the engine oil and engine oil filter . X X X X X Rotate the tires. X X X X X Inspect the engine air filter element, and replace if necessary . X Replace the spark plugs. X Inspect the brake linin[...]

Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the brake linings. X X 386 SCHEDULE “A” 8 M A I N T E N A N C E S C H E D U L E S I n f o r m a t i o n P r o v i d e d b y :[...]

Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (1 10 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs. X[...]

Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plugs.[...]

Miles 108,000 1 14,000 120,000 126,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [108] [1 14] [120] [126] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if nec- essary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark[...]

Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Change the engine oil and engine oil filter . X X X X Rotate the tires. X X X X Inspect the engine air filter element, and replace if necessary . X Inspect the PCV V alve, and replace if necessary . 〫 X Replace the spark plu[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y o u r V e h i c l e .......................... 3 9 2 ▫ Prepar e For The Appointment ............ 3 9 2 ▫ Prepar e A List ........................ 3 9 2 ▫ Be Reasonable W ith Requests ............. 3 9 2 䡵 If Y ou Need Assistance ................... 3 9 2 ?[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner . This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealers[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the U[...]

W ARRANTY INFORMA TION (U.S. V ehicles Only) See the W arranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOP AR 姞 P ARTS Mopar 威 fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best. REPORTING SA[...]

PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P .O. Boxes). • Se[...]

Call T oll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1 143 (Canada) Or V isit us on the W orld Wide W eb at: • www .techauthority .daimlerchrysler .com • www .daimlerchrysler .ca/manuals DEP ARTMENT OF TRANSPORT A TION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories estab- lished by the Nationa[...]

on specified government test surfaces of asphalt and concrete. A tir e marked C may have poor traction perfor- mance. W ARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. T emperature Grades The temperature [...]

INDEX 10 I n f o r m a t i o n P r o v i d e d b y :[...]

ABS (Anti-Lock Brake System) ............ 168,241 Adding Fuel ........................... 2 7 7 Adding W asher Fluid ..................... 1 5 7 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 324 Air Conditioner Maintenance ............... 3 2 9 Air Conditioning ........................ 2 0 3 Air Conditioning, Operating T ips ............ 2[...]

Auxiliary Electrical Outlet (Power Outlet) ...... 1 5 0 Auxiliary Power Outlet ................... 1 5 0 Battery ............................... 3 2 7 Emergency Starting ..................... 3 0 8 Keyless T ransmitter Replacement (RKE) ....... 2 6 Saving Feature (Protection) ............... 1 1 7 B e l t s , D r i v e ............................ [...]

Catalytic Converter ...................... 3 2 5 Caution, Exhaust Gas ................... 7 4 , 1 4 4 CD (Compact Disc) Changer .......... 181,182,194 CD (Compact Disc) Player ......... 177,180,184,187 CD (Compact Disc) Player Maintenance ........ 2 0 2 Cellular Phone ........................ 8 5 , 2 0 2 Center High Mounted Stop Light ............ [...]

Radiator Cap ......................... 3 3 6 Selection of Coolant (Antifreeze) ......... 334,366 T emperature Gauge ..................... 1 6 9 Crankcase Emission Control System .......... 3 2 7 Cruise Control (Speed Control) .............. 1 2 3 C r u i s e L i g h t ........................... 1 7 0 C u p H o l d e r ............................ [...]

Electronic V ehicle Information Center (EVIC) .... 1 3 5 Emergency Brake ........................ 2 4 0 Emergency , In Case of Hazard W arning Flasher ................. 3 0 2 Jacking ............................. 3 0 4 Jump Starting ......................... 3 0 8 T ow Hooks ........................... 3 1 1 Emission Control System Maintenance ....[...]

Filters Air Cleaner .......................... 3 2 4 Engine Oil ........................... 3 2 3 Engine Oil Disposal .................... 3 2 3 F i n i s h C a r e ............................ 3 4 8 Flashers Hazard W arning ....................... 3 0 2 T urn Signal ..................... 166,363,365 Flooded Engine Starting ................... 2 1 [...]

Fuses ................................ 3 5 3 Garage Door Opener (HomeLink 威 ) ........... 1 4 3 Gas Cap (Fuel Filler Cap) ............ 277,279,317 Gasoline (Fuel) ......................... 2 7 3 Gasoline, Reformulated ................... 2 7 4 Gasoline/Oxygenate Blends ................ 2 7 4 Gauges Coolant T emperature .................... 1 6 9 [...]

Hydraulic Clutch Fluid .................... 3 4 2 Identifying Y our Engine ................... 3 1 6 Ignition ............................... 1 4 Cables (Spark Plug W ires) ................ 3 2 4 K e y ................................. 1 4 W iring System (Spark Plug W ires) .......... 3 2 4 Ignition Key Removal ..................... 1 4 Illuminated[...]

LA TCH (Lower Anchors and T ether for CHildren) ..... 6 8 , 6 9 Lead Free Gasoline ...................... 2 7 3 L i f e o f T i r e s ............................ 2 5 8 Lights ............................. 1 1 7 , 3 6 1 Airbag ............................ 6 4 , 1 7 3 Anti-Lock ........................... 1 6 8 Back-Up ............................. [...]

Rear Servicing ........................ 3 6 5 Rear T ail ............................ 3 6 5 Seat Belt Reminder ..................... 1 7 3 Security Alarm (Theft Alarm) .............. 1 7 2 Sentry Key ........................... 1 7 2 Service .............................. 3 6 2 Side Marker .......................... 3 6 5 T ire Pressur e Monitoring[...]

Lubricant Selection ..................... 3 4 4 Shift Speeds .......................... 2 1 8 Map/Reading Lights ..................... 1 3 4 Master Cylinder (Brakes) .................. 3 4 1 Mini-T rip Computer ...................... 1 3 9 M i r r o r s ................................ 8 1 Automatic Dimming ..................... 8 2 Electric Remote[...]

Pressur e W arning Light .................. 1 7 0 Recommendation ................... 322,366 Synthetic ............................ 3 2 2 V iscosity .......................... 322,366 Oil Filter , Selection ....................... 3 2 3 Oil Pressur e Light ....................... 1 7 0 Onboard Diagnostic System .............. 317,318 Opener , Garag[...]

Programming T ransmitters (Remote Keyless Entry) .................... 2 4 Radial Ply T ires ......................... 2 5 6 Radio Broadcast Signals ................... 1 7 6 Radio, Navigation ....................... 1 9 1 Radio Operation ...................... 178,202 Radio, Satellite .......................... 1 9 5 Radio (Sound Systems) .........[...]

Safety Checks Outside V ehicle ............... 7 6 Safety Defects, Reporting .................. 3 9 5 Safety , Exhaust Gas ....................... 7 4 Safety Information, T ire ................... 2 4 5 Safety T ips ............................. 7 4 Satellite Radio .......................... 1 9 5 Satellite Radio Antenna ................... 1 9 9 S[...]

S h i f t i n g ............................... 2 2 0 Automatic T ransmission ............... 220,221 Manual T ransmission ................... 2 1 6 T ransfer Case ...................... 228,232 Shoulder Belt Upper Anchorage .............. 4 3 Shoulder Belts ........................... 3 7 Signals, T urn ................... 1 1 9 , 166,363,365 Snow[...]

System, Navigation ...................... 1 9 1 T achometer ............................ 1 6 6 T emperature Gauge, Engine Coolant .......... 1 6 9 T ether Anchor , Child Restraint ............... 6 8 Theft System Arming ...................... 2 0 Theft System Disarming .................... 2 0 T ie Down Hooks, Cargo ................... 1 5 5 T ilt [...]

T o w i n g ............................ 282,31 1 Disabled V ehicle ....................... 3 1 1 G u i d e .............................. 2 8 7 Recreational .......................... 2 9 6 W e i g h t .............................. 2 8 7 T rac-Lok Rear Axle ...................... 2 3 4 T raction Control ......................... 1 2 7 T raction C[...]

Universal T ransmitter ..................... 1 4 3 Unleaded Gasoline ....................... 2 7 3 Upholstery Care ........................ 3 5 0 V acuum/V apor Harnesses ................. 3 3 8 V a n i t y M i r r o r s ........................... 8 4 V ariance, Compass ....................... 1 4 1 V ehicle Identification Number (VIN) ...........[...]