Kodak A-61097 manual

DIGIT AL SCIENCE TM and IMA GELINK TM Scanners Installation Questionnaire Instructions Mode Setup Instructions A-61097 P ar t Number 4C8894[...]

A-61097 May 1997 1-1 1 Introduction The KODAK DIGITAL SCIENCE™ Mode Setup Software 9000 has been developed to enable you to customize applications using the: • KODAK DIGITAL SCIENCE Document Scanner 9500 • KODAK DIGITAL SCIENCE Scanner/Microimager 990 • KODAK IMAGELINK Microimager 70 • KODAK IMAGELINK Microimager 70 with Advanced Function[...]

1-2 A-61097 May 1997 Software Installation Procedure Follow these steps to install the software: 1. Insert the Mode Setup Software diskette into the drive. 2. Type A:INSTALL next to the DOS prompt and press Return/Enter. If the disk drive on your unit is not designated as the A drive, substitute the correct drive designation in this command string.[...]

A-61097 May 1997 1-3 4. Enter the desired drive and directory designations and press Enter. Drive To Install From: A Drive To Install To: C Directory To Be Installed To: SETUP Directory Information ESCAPE to Abort [Press ENTER to Accept, any other key to Edit] 5. Press Enter to continue the logon procedure. Press any other key to alter the drive a[...]

1-4 A-61097 May 1997 During the installation procedure, the following window will appear if you don’t have the files and buffers set correctly in the config.sys file: Please Wait While Files Are Being Copied ToYour Destination Drive. The CONFIG.SYS File Needs To Be Checked To Make Sure That BUFFERS=40 FILES=40 INSTALLING Mode Setup Software Next,[...]

A-61097 May 1997 1-5 FILE COPY COMPLETE Please enter the name of the registered user below: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Please Wait While Files Are Being Copied To Your Destination Drive. REGISTRATION 7. Type in user name. Press Return/Enter. Type “setup” in c:setup directory to start Mode Setup 8. P[...]

1-6 A-61097 May 1997 Logon Procedure After the installation procedure has been performed, follow these steps to log on to the Mode Setup Software: 1. Access DOS. 2. Change the directory to correspond to the directory designated during the installation procedure. 3. Type setup and press Return/Enter. * EASTMAN KODAK COMPANY * * Model 30 * * Model 70[...]

A-61097 May 1997 1-7 5. Select Continue. Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film Writer Msg DP-12 Print Template Fixed Field Delimiter Set System Clock Version Numbers User COIN Port Protocol Custom Check Digit OI Hardware Charac[...]

1-8 A-61097 May 1997 • Each window should contain an option entitled Previous Menu. Typically, you are returned to the previous menu after completing a definition. If you are not returned to the previous menu after completing a definition, or you want to return without altering the default or previously defined value, select the Previous Menu opt[...]

A-61097 May 1997 1-9 Logout Procedure Once you have completed the installation, the following sequence of steps may be used to log out of the system. From the Mode Configuration window: 1. Select Save & End Session if you wish to save all of the definitions or Don’t Save & End Session if you do not wish to save all of the definitions. You[...]

A-61097 May 1997 2-1 2 Machine Definitions The following section lists the items on the Mainframe Configuration Menu that may be selected for definition. Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film Writer Msg DP-12 Print Template Fix[...]

2-2 A-61097 May 1997 Display Machine Accessories This option displays the status of the various machine accessories and is for viewing only; no selections or entries are made. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Display Machine Accessories. 2. Press Return/[...]

A-61097 May 1997 2-3 Machine ID Number This option establishes a unique identification number for each unit in a multiple-unit installation. The default is 00. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Machine ID Number. 2. Enter a number from 00-99. Display Mach[...]

2-4 A-61097 May 1997 Display Language This option defines the primary display language. The default is English. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Display Language. 2. Select the desired language option. Display Machine Accessories Machine ID Number Displa[...]

A-61097 May 1997 2-5 Measurement System This option defines the primary measurement system. English uses inches as the primary unit of measure. Metric uses millimetres as the primary unit of measure. The default is English. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Sele[...]

2-6 A-61097 May 1997 Programmable Function Keys (P-Keys) This option defines the functions performed by the programmable keys. Refer to Appendix B: Function Codes to determine which function codes and formats to use when programming the P-Keys . ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ?[...]

A-61097 May 1997 2-7 The default values are displayed in the Key Definition table. The following values apply only to the Scanner 9500. Definition Key P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 Prev f37 f98f38 f01,01 f01,02 f01,03 f01,04 f01,05 f01,06 f01,07 ff01,08 Previous Menu Calibrate Stop, End of Job Change to Mode 1 Change to Mode 2 Change to Mode 3 Cha[...]

2-8 A-61097 May 1997 The following default values apply only to the Scanner/Microimager 990: Definition Key P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 f04,2 f45 f09 f08 f37 f30 f44 f46 f07 f98f38 Count only, toggle Print test Total document count Last Image Address Calibrate Amount of film remaining Omit printing on next document only Print position Level 0 St[...]

A-61097 May 1997 2-9 Date Format This option defines the date display format, both the date format and delimiter. Refer to Description 1: Date Format Samples for a description of the available formats. The default is mmddyy. The default delimiter is a slash (/). ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/M[...]

2-10 A-61097 May 1997 Description 1: Date Format Samples Sample Date March 1, 1991 Slash Dash Period Space None mmddyy 03/01/91 03/01/91 03.01.91 03 01 91 030191 mmdd 03/01 03-01 03.01 03 01 0301 ddmmmyy 01/MAR/91 01-MAR-91 01.MAR.91 01 MAR 91 01MAR91 ddmmm 01/MAR 01-MAR 01.MAR 01 MAR 01MAR mmyy 03/91 03-91 03.91 03 91 0391 yddd 1/060 1-060 1.060 1[...]

A-61097 May 1997 2-11 Time Format This option defines the time display format. Refer to Description 2: Time Format Samples for a description of the available formats. The default is 12 hour with AM/PM. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Time Format. 2. Sel[...]

2-12 A-61097 May 1997 Alarm Tone This option defines tone or pitch of the audible alarm. The default is High. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Alarm Tone. 2. Select the desired alarm tone pitch. Display Machine Accessories Machine ID Number Display Langu[...]

A-61097 May 1997 2-13 Document Printer/Film Writer Messages This option defines messages that may be printed by a document printer or film writer. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Doc Printer/Film Writer Msg. Messages are limited to thirty-eight (38) cha[...]

2-14 A-61097 May 1997 Message 0 is predefined and cannot be changed. Messages 1 through 9 are programmable using the following sequence of steps: 1. Select a message number. 2. Press Return/Enter. 3. Enter the desired message text. 4. Press Return/Enter. Definition Msg 0 1 2 3 4 5 6 7 8 9 Prev Previous Menu Diagnostic Message - No Entry Allowed.[...]

A-61097 May 1997 2-15 Print Template Setup This option defines as many as ten (10) unique print templates. The template definitions are used when programming Document Printer 12 print definitions. The default print template is Print Template 1, which prints Full IA w/No Delimiters on Line 1. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900[...]

2-16 A-61097 May 1997 1. Follow these steps for each line/item to be printed (maximum twelve per template): a. Select the next available item number (or Item 1 if this is the first item). b. Enter a line number corresponding to the line number on the print template master. c. Select one or more of the print items listed (maximum three items per lin[...]

A-61097 May 1997 2-17 If Check Digit is selected, the following window is displayed: Document Printer 12 Print Template # 1 2 3 4 5 6 7 8 9 10 11 12 Previous Menu Item Line Print Item 01 <IA-No Del> <Message 1> Mod 7A - IA Only Mod 11A - IA Only Mod 7B - IA Only Mod 7B - Full IA Mod 10 - IA Only Mod 10 - Full IA Mod 11B - IA Only Mod 11[...]

2-18 A-61097 May 1997 The master template is designed to assist you in the placement of information printed by the Document Printer 12. Follow these steps to use the master templates: 1. Obtain a sample of the customer’s document(s). 2. Determine the starting print position (how far from the leading edge of the document printed information should[...]

A-61097 May 1997 2-19 Dotted line = Starting print position (distance from the leading edge of the document). Line 1 Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line 8 Line 9 Line 10 Line 11 Line 12 Line 13 Line 14 Line 15 Line 16 Line 17 Line 18 Line 19 Line 20 Line 21 Line 22 Line 23 Line 24 Line 25 Line 26 Line 27 Line 28 Line 29 Line 30 Line 31 L[...]

2-20 A-61097 May 1997 Dotted line = Starting print position (distance from the leading edge of the document). Line 1 Line 2 Line 3 Line 4 Line 5 Line 6 Line 7 Line 8 Line 9 Line 10 Line 11 Line 12 Line 13 Line 14 Line 15 Line 16 Line 17 Line 18 Line 19 Line 20 Line 21 Line 22 Line 23 Line 24 Line 25 Line 26 (4 lines per inch) Vertical placement on [...]

A-61097 May 1997 2-21 Fixed Field Delimiter This option defines the fixed field delimiter used in the Image Address Display. The default is a Period (.) . NOTE: The Fixed Field Delimiter doesn’t appear on the display; it appears when printing the Image Address. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/[...]

2-22 A-61097 May 1997 Set System Clock This option sets the system clock. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Set System Clock. Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time For[...]

A-61097 May 1997 2-23 3. Verify that the terminal time should be downloaded by selecting Yes; or to cancel the download, select No. If the computer being used to program the unit does not have an internal clock or the internal clock is not accurate: 4. Select the time or date component you wish to define ( month, day, year, hour or minute). Display[...]

2-24 A-61097 May 1997 Version Numbers This option displays the current software version(s) installed in the machine and is for viewing only; no selections or entries are made. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Version Numbers. Display Machine Accessories [...]

A-61097 May 1997 2-25 User COIN Port Protocol This option enables or disables the user COIN port for communication protocols associated with OCR data, Document Scanning Array / Bar Code Reader, or Customer specified. The default value is Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 [...]

2-26 A-61097 May 1997 If User-Defined Protocol is selected, the following window will be displayed: Baud Rate Parity Bit Char. Length Handshaking Update FF Previous Menu User COIN Port Config Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Fi[...]

A-61097 May 1997 2-27 5. Select Parity Bit. 6. Select the desired parity. Baud Rate Parity Bit Char. Length Handshaking Update FF Previous Menu User COIN Port Config Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film Writer Msg DP-12 Print [...]

2-28 A-61097 May 1997 9. Select Handshaking. 10. Select the handshaking protocol. Handshaking Baud Rate Parity Bit Char. Length Handshaking Update FF Previous Menu User COIN Port Config Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film Wri[...]

A-61097 May 1997 2-29 Custom Check Digit This option determines the check digit algorithm to be used when a custom check digit is calculated. NOTE: If a standard check digit algorithm is desired, specify the desired algorithm during Image Address print definitions within each mode setup. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■[...]

2-30 A-61097 May 1997 Check Digit = Constant 2 - Custom Check Digit Formula [Sum of IA Digits * Attributes] + Constant 1 Divisor Custom Check Digit Definition Current Value Parameter 46231546231 00 00 07 Right No abcdefghijk Attributes Constant 1 Constant 2 Divisor Left/Right LUT Status Lookup Table Help Previous Menu The parameters displayed in th[...]

A-61097 May 1997 2-31 • Constant1—A constant value in the range 0 through 99. • Divisor—a constant value between 0 and 99. NOTE: The divisor is not used if value specified is zero (0). In addition to the parameters in the equation, there are other user defined parameters which affect check digit processing: • Left/Right specifier (also re[...]

2-32 A-61097 May 1997 Sample check digit calculation #1 Assume the following: Image Address = 123.45.678.912 Attributes = 46231546231 Constant 1 = 7 Constant 2 = 10 Divisor = 11 Left/Right = Right LUT Status = No/off Lookup Table = abcdefghijk Then the check digit calculation would be: 1. Set up the equation: Check Digit = 10 - [Calculation 1] + 7 [...]

A-61097 May 1997 2-33 Sample check digit calculation #2 Assume the following: Image Address = 123.45.678.912 Attributes = 46231546231 Constant 1 = 7 Constant 2 = 10 Divisor = 11 Left/Right = Right LUT Status = Yes/on Lookup Table = abcdefghijk Then the check digit calculation would be: 1. Set up the equation: Check Digit = 10 - [Calculation 1] + 7 [...]

2-34 A-61097 May 1997 To program a custom check digit algorithm, use the following sequence of steps: 1. Select the Attributes parameter for definition. 2. Enter the desired attribute values. Enter attribute values. Req’d entry 11 digits. 46231546231 To Change: Enter Value To Retain: Press Enter Check Digit = Constant 2 - [Sum of IA Digits * Attr[...]

A-61097 May 1997 2-35 5. Select the Constant2 parameter for definition. 6. Enter a value between 00 – 99. Enter constant #2. Req’d entry 2 digits. 00 To Change: Enter Value To Retain: Press Enter Check Digit = Constant 2 - [Sum of IA Digits * Attributes] + Constant 1 Divisor Current Value Parameter 46231546231 00 00 07 Right No abcdefghijk Attr[...]

2-36 A-61097 May 1997 9. Select the Left/Right parameter for definition. 10. Select the digit to be used during calculation of the check digit. Check Digit = Constant 2 - [Sum of IA Digits * Attributes] + Constant 1 Divisor Current Value Parameter 46231546231 00 00 07 Right No abcdefghijk Attributes Constant 1 Constant 2 Divisor Left/Right LUT Stat[...]

A-61097 May 1997 2-37 13. Select the Lookup Table parameter for definition. 14. Enter the desired lookup table values. Enter lookup table. Req’d entry 11 digits. abcdefghijk To Change: Enter Value To Retain: Press Enter Check Digit = Constant 2 - [Sum of IA Digits * Attributes] + Constant 1 Divisor Current Value Parameter 46231546231 00 00 07 Rig[...]

2-38 A-61097 May 1997 OI Hardware Character Set This option defines non-English character sets which may be used by the Operator Interface, Document Printers and the Film Writer. English characters are contained in both sets. The default OI character set is Anglo/Japanese. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ?[...]

A-61097 May 1997 2-39 Save Configuration to PC This option is used to download a configuration file from the scanner or microfilmer onto diskette. This is useful in creating configuration files which may be transported to other units (see the Load Config from PC option). This is also used to create backup files. This option should be performed any [...]

2-40 A-61097 May 1997 Load Configuration from PC This option is used to upload a configuration file from diskette to the scanner or microfilmer. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Load Configuration from PC. 2. Enter a file name to upload. Display Machine [...]

A-61097 May 1997 3-1 3 Selecting the Mode Configuration Window This section lists the Mode Definitions for the Scanner/Microimager. Follow these steps to select the Mode Definition screen. Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film [...]

3-2 A-61097 May 1997 2. Select a mode to be defined. The Mode Configuration window will be displayed, with the Mode Number you selected for definition displayed at the top. MODE 10 3 Lvl Supprs 4233 2112 None Auto Duplex ????? 1 Roll Comic Off Off Off Xport Off Undef Undef Off Off Off Lvl 2 On N N N Off On Disply Off Off Off Off No Sav F Mode Name [...]

A-61097 May 1997 3-3 Mode Definitions The following section lists the items on the Mode Configuration Menu that may be selected for definition. Unavailable machine types are indicated by hollow boxes. Mode Name This option defines the mode name. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ?[...]

3-4 A-61097 May 1997 Index Format This mode defines the index format used by the application mode. Refer to Description 3: Index Formats for a description of the index formats. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 When using a Microimager 70 without the Advanced Funct[...]

A-61097 May 1997 3-5 Description 3: Index Formats There are five Index Format options available: Single Level IA 1 (Level 1) IA 2 (Level 1) IA 3 (Level 1) IA 4 (Level 1) Whenever a small image mark is placed next to a document and/or a document is assigned Level 1, the Image Address field associated with Level 1 (Field A) is incremented. Two Level [...]

3-6 A-61097 May 1997 Description 3: Index Formats (continued) Three Level IA 1.0.0 IA 1.1.0 IA 1.1.1 IA 2.0.0 (Level 3) (Level 2) (Level 1) (Level 3) Whenever a large image mark is placed next to a document and/or a document is assigned Level 3, the Image Address field associated with Level 3 (Field C) is incremented and the fields associated with [...]

A-61097 May 1997 3-7 Image Address Display Format This mode defines the format of the Image Address display which appears on the control panel. The default is Suppress. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select IA Display Format. Mode Configuration Don't Sav[...]

3-8 A-61097 May 1997 Image Address Field Widths This mode defines the Image Address field widths. Refer to Description 4: Image Address Fields for a description of proper field definitions. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 When using a Microimager 70 without the A[...]

A-61097 May 1997 3-9 1. Select IA Field Widths. Mode Configuration Don't Save & End Session End Configuration Save & End Session Previous Menu Mode Number: 10 Mode Name: MODE10 Fixed Field Field A Field B Field C Previous Menu Field Num MODE 10 3 Lvl Supprs 4233 2112 None Auto Duplex ????? 1 Roll Comic Off Off Off Xport Off Undef Undef[...]

3-10 A-61097 May 1997 Description 4: Image Address Fields An Image Address is a unique identifier assigned to each individual document by the Microimager 70, Scanner 900, Scanner 923, Scanner 9500, or Scanner/Microimager 990. An Image Address may contain up to 15 characters, consisting of a maximum of 12 digits Description 4: Image Address Fields. [...]

A-61097 May 1997 3-11 Description 4: Image Address Fields (continued) • Two Level Field A is defined as having a field length greater than zero (1 – 9) Field B is defined as having a field length greater than zero (1 – 9) Field C is defined as having a field length of zero (0) Fixed Field may be defined, if desired (0 – 9) • Two Level Off[...]

3-12 A-61097 May 1997 Level Rules This mode defines the level of a document based upon the level of the previous document. These definitions are used as defaults when the document level is not determined by another method (i.e., Footswitch, P-Key, Level Key, etc.) ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner[...]

A-61097 May 1997 3-13 1. Select Level Rules. Mode Configuration Don't Save & End Session End Configuration Save & End Session Previous Menu Mode Number: 10 Mode Name: MODE10 Level 0 Level 1 Level 2 Level 3 Previous Menu Field MODE 10 3 Lvl Supprs 4233 2112 None Auto Duplex ????? 1 Roll Comic Off Off Off Xport Off Undef Undef Off Off Of[...]

3-14 A-61097 May 1997 Batching This mode defines the number of documents of a specified level to process prior to performing a predefined action. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Batching. Batch Level Batch Value Start of Batch Function End of Batch Func[...]

A-61097 May 1997 3-15 Batch Value Defines the number of documents to be counted prior to performing a predefined action. The default value is 99. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Batch Value. Batch Level Batch Value Start of Batch Function End of Batch F[...]

3-16 A-61097 May 1997 Start of Batch Function This mode defines the action(s) to be taken prior to processing the document in the batch. The default value is Nothing. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Start of Batch Function. Batch Level Batch Value Start[...]

A-61097 May 1997 3-17 End of Batch Function This mode defines the action(s) to be taken after processing the document in the batch. The default value is f98, Stop. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select End of Batch Function. Batch Level Batch Value Start of B[...]

3-18 A-61097 May 1997 AEC Mode This mode enables or disables Automatic Exposure Control. Fixed Mode disables Automatic Exposure Control. Auto Mode enables Automatic Exposure Control. The default value is Auto Mode. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select AEC Mo[...]

A-61097 May 1997 3-19 Film Mode This mode defines the orientation of documents on film. Refer to Description 5: Film Modes for a description of the available film modes. The default value is Duplex. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Film Mode. Simplex Mod[...]

3-20 A-61097 May 1997 • Simplex Mode Simplex format allows one image to be exposed across the film width. A 24:1 reduction ratio is used for this format. • Duplex Mode Duplex format allows front and back images of the same document to be exposed (at the same time) across the film width. A 40:1 or 50:1 reduction ratio is used for this format. ?[...]

A-61097 May 1997 3-21 Reduction Ratio This mode defines the level of magnification. The default value is Don’t Care. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Reduction Ratio. Reduction Ratio Don't Care 24x 40x 50x Previous Menu Mode Configuration Don&apos[...]

3-22 A-61097 May 1997 Number of Cassettes This mode defines the minimum number of cassettes that must be installed during filming. If Two Cassettes is chosen, you must always use two cassettes. If One Cassette is chosen, you may use one or two cassettes. The default value is One Cassette. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ?[...]

A-61097 May 1997 3-23 Film Writer NOTE: The Film Writing Module must be installed. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Film Writer. Character Orientation Image Addr Print Format Same Sequence per Level Print Sequence - Level 0 Print Sequence - Level 1 Print[...]

3-24 A-61097 May 1997 Character Orientation This mode defines the orientation of the information printed by the film writer. The default is Comic. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Character Orientation. Character Orientation Image Addr Print Format Same [...]

A-61097 May 1997 3-25 Image Address Print Format This mode defines the format of the Image Address printed on film. The default is Compress. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Image Addr Print Format. Character Orientation Image Addr Print Format Same Sequ[...]

3-26 A-61097 May 1997 Write Definitions This mode defines the information printed on film next to each document, based upon the document level. The default value for all levels is <FF/IA-All Del>. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 When using a Microimager 70 [...]

A-61097 May 1997 3-27 If different information is to be printed next to documents of different levels: 1. Select Print Sequence – Level # for the desired level. Full Image Address Indexed Fields Only Current Field Level Spaces between Items Current Day Current Date Current Time Document Counter Message 1 Message 2 Message 3 Message 4 Message 5 Me[...]

3-28 A-61097 May 1997 Image Management Code NOTE: The Film Writing Module must be installed. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Image Mgmt Code. Status IMT Search Prg Number Magnification Splice Definition Image Mark Sizes Image Polarity Duplex Front Locat[...]

A-61097 May 1997 3-29 Status This mode enables or disables the use of IMC options. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Status. Status IMT Search Prg Number Magnification Splice Definition Image Mark Sizes Image Polarity[...]

3-30 A-61097 May 1997 IMT Search Program Number This mode defines the IMT search program number. The default value is 00. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select IMT Search Prg Number. Status IMT Search Prg Number Magnification Splice Definition Image Mark Size[...]

A-61097 May 1997 3-31 Magnification This mode defines for the KODAK IMAGELINK™ Digital Workstation (with Zoom Lens Accessory) the desired level of magnification. The default value is 20. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Magnification. Status IMT Search[...]

3-32 A-61097 May 1997 Splice Definition This mode defines the desired action when a splice is detected. The default value is Ignore. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Splice Definition. Select any of the Sort Criteria and the following screen appears: Sta[...]

A-61097 May 1997 3-33 Image Mark Sizes This mode defines the image mark sizes used (small, medium, and large). The default value is Kodak Standard. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Image Mark Sizes. Status IMT Search Prg Number Magnification Splice Defin[...]

3-34 A-61097 May 1997 Image Polarity This mode defines the polarity of the image marks relative to the polarity of the document images. The default value is Same as Image Mark. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Image Polarity. Status IMT Search Prg Number[...]

A-61097 May 1997 3-35 Duplex Front Location The mode defines for the KODAK IMAGELINK™ Digital Workstation where the front side image is located. The default value is Same as IM Channel. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Duplex Front Location. Status IMT[...]

3-36 A-61097 May 1997 Film Image Orientation The mode defines where the top of the image is located for the KODAK IMAGELINK™ Digital Workstation. The default value is Leading Edge Up. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Film Image Orientation. Status IMT [...]

A-61097 May 1997 3-37 Image Offset This mode defines the position of the image marks relative to the leading edge of the document. The default value is 0. ■ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Image Offset. Status IMT Search Prg Number Magnification Splice De[...]

3-38 A-61097 May 1997 Length Monitor NOTE: The Advanced Document Controller must be installed. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Length Monitor. Status Max Document Length Min Document Length Length Err Response Previous Menu Mode Configuration Don't[...]

A-61097 May 1997 3-39 Status This mode enables or disables length monitoring. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Status. Status Max Document Length Min Document Length Length Err Response Previous Menu Mode Configurati[...]

3-40 A-61097 May 1997 Maximum Document Length This mode defines the maximum document length accepted. The default value is 13.000 inches/325 mm. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Max Document Length. Status Max Document Length Min Document Length Length E[...]

A-61097 May 1997 3-41 Minimum Document Length This mode defines the minimum document length accepted. The default value is 02.500 inches/63 mm. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Min Document Length. Status Max Document Length Min Document Length Length Er[...]

3-42 A-61097 May 1997 Length Error Response This mode defines the action taken if a document is smaller than the minimum length specified or larger than the maximum length specified. The default value is Display and Beep. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select[...]

A-61097 May 1997 3-43 Skew Monitor ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 NOTE: The Advanced Document Controller must be installed. 1. Select Skew Monitor. Skew Detect Status Skew Threshold Skew Error Response Previous Menu Mode Configuration Don't Save & End S[...]

3-44 A-61097 May 1997 Skew Threshold This mode defines the amount of tolerable skew. If 5 Degrees is selected, an error will be reported if the amount of document skew is between 5 and 30 degrees. If 10 Degrees is selected, an error will be reported if the amount of document skew is between 10 and 30 degrees. Regardless of the option selected, if t[...]

A-61097 May 1997 3-45 Skew Error Response This mode defines the action taken if the amount of document skew is greater than the threshold specified. The default value is Display and Beep. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Skew Err Response. Skewed Error R[...]

3-46 A-61097 May 1997 Check Stacker NOTE: The Check Stacker must be installed. This mode defines when the check stacker is activated. Continuous will activate the check stacker whenever the side panel switch is on. Documents in Transport will activate the check stacker only when there are documents exiting the transport. The default value is Docume[...]

A-61097 May 1997 3-47 Endorser NOTE: The Endorser must be installed. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Endorser. Status Mode Print Position Previous Menu Mode Configuration Don't Save & End Session End Configuration Save & End Session Previou[...]

3-48 A-61097 May 1997 Endorser Status Enables or disables the endorser. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Status. Status Mode Print Position Previous Menu Mode Configuration Don't Save & End Session End Confi[...]

A-61097 May 1997 3-49 Endorser Mode This mode defines whether the endorser will print continually or only once per document. Continuous will activate the Endorser continually. Single Stamp will activate the Endorser only once per document. The default value is Continuous. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■[...]

3-50 A-61097 May 1997 Endorser Print Position This mode defines how far from the leading edge of the document the endorsement will appear: The default value is 0000.250 inch/ 6.350 mm. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Print Position. Status Mode Print Po[...]

A-61097 May 1997 3-51 Footswitch Pressed NOTE: The Footswitch accessory must be installed. This mode defines the action which results when the footswitch is pressed. The default is Undefined. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 When using a Microimager 70 without the[...]

3-52 A-61097 May 1997 Footswitch Released NOTE: The Footswitch accessory must be installed. This mode defines the action which results when the footswitch is pressed. The default is Undefined. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Ftswitch Pressed. Undefined [...]

A-61097 May 1997 3-53 Footswitch Confirmation Tone NOTE: The Footswitch accessory must be installed. This mode enables or disables the footswitch press confirmation tone. The default is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Ftswitch Cnf Tone.[...]

3-54 A-61097 May 1997 Patch Reader 1 NOTE: A Patch Reader accessory or Document Scanning Array must be installed. Enables or disables the primary patch reader. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Patch Reader 1. Mode Co[...]

A-61097 May 1997 3-55 Patch Reader 2 NOTE: A Patch Reader accessories or Document Scanning Array must be installed. Enables or disables the secondary patch reader. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ❏ Scanner/Microimager 990 ■ Scanner 9500 1. Select Patch Reader 2. Mod[...]

3-56 A-61097 May 1997 Patch Definition NOTE: At least one Patch Reader accessory or Document Scanning Array must be installed. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Patch Definition. Mode Configuration Don't Save & End Session End Configuration Save [...]

A-61097 May 1997 3-57 Transfer Patch Definition This mode defines which level should be assigned to the next document when a transfer patch is used. The default value is Level 2. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Transfer Patch Definition. Mode Configurat[...]

3-58 A-61097 May 1997 Film Transfer Patches This mode defines whether or not a document containing a transfer patch is to be filmed. The default value is Transfer Patch Filmed. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select Film Transfer Patches. Mode Configuration Do[...]

A-61097 May 1997 3-59 Patch Recognition This mode defines which patch codes will be recognized by the system. The default value is 2, 3, & T. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Patch Recognition. Mode Configuration Don't Save & End Session End[...]

3-60 A-61097 May 1997 Bar Code NOTE: A Bar Code Reader must be installed. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Bar Code. Mode Configuration Don't Save & End Session End Configuration Save & End Session Previous Menu Mode Number: 10 Mode Name: MO[...]

A-61097 May 1997 3-61 Bar Code Reading Status Enables or disables bar code reading. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Bar Code Reading Status. Mode Configuration Don't Save & End Session End Configuration Sav[...]

3-62 A-61097 May 1997 Bar Code Type Identifies the type of bar code which is to be read. The default value is Code 39. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Bar Code Type. Mode Configuration Don't Save & End Session End Configuration Save & End S[...]

A-61097 May 1997 3-63 Number of Bar Code Characters This mode defines the minimum bar code length allowed (in terms of the number of characters encoded). The default value is 3. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select # of Bar Code Characters. Mode Configuratio[...]

3-64 A-61097 May 1997 Bar Codes per Document This mode defines the number of bar codes per document to be decoded. The default value is One Code. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Bar Codes per Document. Mode Configuration Don't Save & End Sessio[...]

A-61097 May 1997 3-65 Distance Between Codes This mode defines the minimum bar code height allowed. The height of the tallest bar code determines the distance between codes. The default value is 1.000 inch/25.400 mm. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Dist[...]

3-66 A-61097 May 1997 Scan Direction This mode defines whether the bar codes may be read in only one direction (from left to right) or in either direction (from left to right or from right to left). The default value is Unidirectional (from left to right only). ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Mi[...]

A-61097 May 1997 3-67 Image Processing Enables or disables image processing; indicates whether or not image processing is required to enhance the overall quality of the bar codes used. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Selec[...]

3-68 A-61097 May 1997 Partial Read Enabled Enables or disables partial bar code reading. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Partial Read Enabled. Mode Configuration Don't Save & End Session End Configuration S[...]

A-61097 May 1997 3-69 Minimum Partial Characters NOTE: Partial Reading must be enabled or this definition will be ignored. This mode defines the minimum number of characters which must be properly decoded to constitute a partial read. The default value is 5-80. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Mi[...]

3-70 A-61097 May 1997 DSA Patch Reading Status Enables or disables patch reading using the Document Scanning Array. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select DSA Patch Reading Status. Mode Configuration Don't Save & [...]

A-61097 May 1997 3-71 Patch Horizontal Location This mode defines the position of patches on the document(s) in terms of the distance from the left side of the transport. The default value is 5.12 inches/130.048 mm. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Patch[...]

3-72 A-61097 May 1997 End Fed Patch Reading Status Enables or disables end fed patch reading using the Document Scanning Array. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select End Fed Patch Read Status. Mode Configuration Don'[...]

A-61097 May 1997 3-73 Level Change via Bar Code Enables level changes based upon detection of a bar code. The default value is Undefined. ❏ Microimager 70 ■ Microimager 70/AFM ❏ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Level Change via Bar Code. Mode Configuration Don't Save & End Session End[...]

3-74 A-61097 May 1997 Confirmation Tones NOTE: The tones must have been enabled during machine configuration; otherwise, these definitions will be ignored. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Confirmation Tone. Patch Detected Tone Bar Detected Tone Bar Code[...]

A-61097 May 1997 3-75 Patch Detected Tone NOTE: Patch reading must be enabled. In addition, the confirmation tones must have been enabled during machine definitions; otherwise, this definition will be ignored. This mode enables or disables a confirmation tone issued when a patch document is detected. The default value is Off or Disabled. ❏ Microi[...]

3-76 A-61097 May 1997 Bar Detected Tone NOTE: Bar Code reading must be enabled. In addition, during machine definitions the confirmation tones must have been enabled; otherwise, this definition will be ignored. Enables or disables a confirmation tone issued when a bar code document is detected. The default value is Off or Disabled. ❏ Microimager [...]

A-61097 May 1997 3-77 Bar Code/Patch Tone NOTE: Patch reading and Bar Code reading must be enabled. In addition, the confirmation tones must have been enabled during machine definitions; otherwise, this definition will be ignored. Enables or disables a confirmation tone issued when a bar code and a patch are both recognized. The default value is Of[...]

3-78 A-61097 May 1997 OCR Status NOTE: The OCR accessory must be installed. Enables or disables Optical Character Recognition. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 1. Select OCR Status. Mode Configuration Don't Save & End[...]

A-61097 May 1997 3-79 COIN User Channel NOTE: If the machine definition User COIN Port Protocol was disabled, these definitions will be ignored. Enables or disables the COIN2 user channel. If a standard form of output was chosen during machine definition (Bar Code/KDIS Protocol or OCR Data Protocol), this definition should be set to Enabled which w[...]

3-80 A-61097 May 1997 Transmit Data This mode defines the data output via the COIN2 port when a user- defined protocol (User-Defined KDIS Format or User-Defined Protocol) is chosen during machine definition. The default values are FF/IA for all levels. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager[...]

A-61097 May 1997 3-81 If different information is to be transmitted for documents of different levels: 1. Select Define Level # for the desired level. Transmit Items Current Transmit Sequence New Transmit Sequence <FF/IA> Full Image Address Indexed Field(s) Only Current Field Value Current Day Current Date Current Time Document Counter Roll N[...]

3-82 A-61097 May 1997 Printer Control NOTE: The Document Printer Controller must be installed ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Printer Control. Printer Control Mode Configuration Don't Save & End Session End Configuration Save & End Session [...]

A-61097 May 1997 3-83 Print Position This mode defines how far from the leading edge of the document(s) the information printed by the document printer(s) will appear. The default value is 00.250 inch/6.25 mm. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Print Posit[...]

3-84 A-61097 May 1997 Special Character Set This mode defines the size font to be printed. Select either the smaller or larger font size when using the Document Printer 12. The default value is Use Smaller Font. NOTE: This selection is not available if the wrong printer driver board is installed. The following message appears: Incorrect revision of[...]

A-61097 May 1997 3-85 Primary Document Printer 1 NOTE: A Document Printer 1 accessory must be installed. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Primary DP-1. Primary Document Printer Mode Configuration Don't Save & End Session End Configuration Save &[...]

3-86 A-61097 May 1997 Fonts/Orientation This mode defines the size and orientation of the characters printed by the primary Document Printer 1. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Fonts/Orientation. Document Printer Sta[...]

A-61097 May 1997 3-87 Print Definitions This mode defines the information printed on each document, based upon the document level. The default values are Nothing Printed for Level 0 documents; Full Image Address with all delimiters for Level 1, Level 2, and Level 3 documents <FF/IA All Del>. ■ Microimager 70 ■ Microimager 70/AFM ■ Scann[...]

3-88 A-61097 May 1997 If Spaces between items is selected, you must select the desired number of spaces. If Check Digit is selected, the following window is displayed: Check Digit Current Print Sequence Display Values New Print Sequence Display Values Mod 7A IA Only Mod 11A IA Only Mod 7B IA Only Mod 7B Full IA Mod 10 IA Only Mod 10 Full IA Mod 11B[...]

A-61097 May 1997 3-89 If different information is to be printed on documents of different levels: 1. Select Print Sequence - Level # for the desired level. Print Items Current Print Sequence Display Values New Print Sequence Display Values Full IA w/No Delimiters Full IA w/FF Delimiter Full IA w/All Delimiter Fixed Field Only Indexed Fields Only Cu[...]

3-90 A-61097 May 1997 Secondary Document Printer 1 NOTE: Two Document Printer 1 accessories must be installed. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Secondary DP-1. Second Document Printer Mode Configuration Don't Save & End Session End Configuration[...]

A-61097 May 1997 3-91 Document Printer Status Enables or disables the secondary Document Printer 1. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Document Printer Status. Second Document Printer Mode Configuration Don't Save[...]

3-92 A-61097 May 1997 Fonts/Orientation—DP2 This mode defines the size and orientation of the characters printed by the secondary Document Printer 1. The default value is Off or Disabled. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Fonts/Orientation. Second Docum[...]

A-61097 May 1997 3-93 Print Definitions—DP2 This mode defines the information printed on each document, based upon the document level. The default values are Nothing Printed for Level 0 documents; Full Image Address with all delimiters for Level 1, Level 2, and Level 3 documents. ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scann[...]

3-94 A-61097 May 1997 If Check Digit is selected, the following window is displayed: Check Digit Current Print Sequence Display Values New Print Sequence Display Values Mod 7A IA Only Mod 11A IA Only Mod 7B IA Only Mod 7B Full IA Mod 10 IA Only Mod 10 Full IA Mod 11B IA Only Mod 11B Full IA Custom IA Only Custom Full IA Previous Menu 3. Select the [...]

A-61097 May 1997 3-95 If Message Number is selected, the following window is displayed: Message Number 1 Message Number 2 Message Number 3 Message Number 4 Message Number 5 Message Number 6 Message Number 7 Message Number 8 Message Number 9 Previous Menu Message Number Current Print Sequence Display Values New Print Sequence Display Values 4. Selec[...]

3-96 A-61097 May 1997 Document Printer 12 NOTE: The Document Printer 12 accessory must be installed ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Doc. Printer 12. Document Printer 12 Mode Configuration Don't Save & End Session End Configuration Save & En[...]

A-61097 May 1997 3-97 Document Printer Status—DP12 Enables or disables the Document Printer 12. The default value is Off or Disabled. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Document Printer Status. Field PAW 12 Status Document Printer 12 Mode Configuration D[...]

3-98 A-61097 May 1997 Fonts/Orientation—DP12 This mode defines the size and orientation of the characters printed by the Document Printer 12. The default value is Comic Orientation. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 1. Select Fonts/Orientation. Field DP-12 Font S[...]

A-61097 May 1997 3-99 Print Definitions—DP12 This mode defines the information printed on each document, based upon the document level. The default values are No Print Template for Level 0 documents; Print Template for Level 1, Level 2, and Level 3 documents. The default is IA-No Del. ■ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ [...]

3-100 A-61097 May 1997 When using a Microimager 70 with the Advanced Function Module installed, all of the print templates defined during machine configuration are available for selection. 2. Select the print template which contains the information to be printed on all documents. 3. Select Print Sequence—Level # for the desired level. Print Templ[...]

A-61097 May 1997 3-101 Document Sorter OFF ❏ Microimager 70 ■ Microimager 70/AFM ■ Scanner 900 ■ Scanner 923 ■ Scanner/Microimager 990 ■ Scanner 9500 Select Document Sorter and the following screen appears: Status Error Response Sort Criteria Document Sorter Sort Criteria Don't Save & End Session End Configuration Save & En[...]

3-102 A-61097 May 1997 If 4 selections have been set and you choose a 5th option, the following screen appears: Maximum number of sorting criteria has been reached Press ENTER to proceed… ** ERROR ** Mode Configuration Don't Save & End Session End Configuration Save & End Session Previous Menu Mode Number: 10 Mode Name: MODE10 MODE 1[...]

A-61097 May 1997 3-103 Film Definition This mode enables or disables filming. This option is set as follows: Microimager 70 F (film) Scanners 900, 923, 9500 NoF (no film) Scanner/Microimager 990 F (film) ❏ Microimager 70 ❏ Microimager 70/AFM ❏ Scanner 900 ❏ Scanner 923 ■ Scanner/Microimager 990 ❏ Scanner 9500 Mode Configuration Don&apos[...]

A-61097 May 1997 4-1 4 Installation Questionnaire General Information CUSTOMER NAME: __________________________________________________________________ CUSTOMER ADDRESS: _______________________________________________________________ __________________________________________________________________________________ CUSTOMER CONTACT: _______________[...]

4-2 A-61097 May 1997 Machine Definitions 0.0 Accessory Status _____________ Adv. Doc. Controller _____________ Bar Code Reader _____________ Doc Scanning Array _____________ Check Feeder _____________ Check Stacker _____________ Document Sorter _____________ Endorser _____________ Footswitch _____________ Film Writing Module _____________ Image Mar[...]

A-61097 May 1997 4-3 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 LINE PRINT ITEM Print Template # ITEM 1 2 3 4 5 6 7 8 9 10 11 12 LINE PRINT ITEM Print Template # _ ITEM 1 2 3 4 5 6 7 8 9 10 11 12 LINE PRINT ITEM Print Template # ITEM 1 2 3 4 5 6 7 8 9 10 11 12 LINE PRINT ITEM Print Template # ITEM 1 2 3 4 5 6 7 8 9 10 11 12 LINE PRINT ITEM Print Template # _ [...]

4-4 A-61097 May 1997 Mode Definitions MODE 1 ❑ Original Setup ❑ Update (enter date) __________ Filename: _____________ .cfg May be linked with Mode(s): ________________ __________ 19.0 Mode Name __________ 20.0 Index Format __________ 21.0 Image Address Display Format 22.0 Image Address Field Widths __________ Fixed Field __________ Field C—L[...]

A-61097 May 1997 4-5 Mode Definitions MODE 1 44.0 COIN User Channel 44.1 Transmit Data ________ Level 0 ________ Level 1 ________ Level 2 ________ Level 3 45.0 Printer Control 45.1 _______ IA Print Format 45.2 _______ Print Position 45.3 _______ Special Char Set 46.0 Primary Document Printer 1 46.1 _______ Status 46.2 _______ Font/Orientation 46.3 [...]

A-61097 May 1997 A-1 A PPEN D IX A : System Map Display Machine Accessories Machine ID Number Display Language Measurement System Programmable Function Keys Date Format Time Format Alarm Tone Doc Printer/Film Writer Msg DP-12 Print Template Fixed Field Delimiter Set System Clock Version Numbers User COIN Port Protocol Custom Check Digit OI Hardware[...]

A-2 A-61097 May 1997 Mode to Mode Copy Mode Number: 10 Mode Name: MODE10 Copy Mode 1 Copy Mode 2 Copy Mode 3 Copy Mode 4 Copy Mode 5 Copy Mode 6 Copy Mode 7 Copy Mode 8 Copy Mode 9 Copy Mode 10 Copy Mode 11 Copy Mode 12 Copy Mode 13 Copy Mode 14 Copy Mode 15 Copy Mode 16 Copy Mode 17 Copy Mode 18 Previous Menu Copy From Mode: Copy From Mode: Select[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

† May be executed while transport is running. * Available when filming; for use only with Microimager 70 (with or without AFM), and Scanner/Microimager 990. ** Available when scanning; for use only with the Scanner 900, Scanner 923, Scanner 9500, and Scanner/Microimager 990. *** Available when using advanced capabilities; for use only with the Mi[...]

A-61097 May 1997 C-1 A PPEN D IX C : Recommended Entries Item Description Values 0.0 Accessory Status PRES (Present) NOTPRES (Not Present) 1.0 Machine ID Number 00 – 99 2.0 Display Language ENG (English) FREN (French) GERM (German) ITAL (Italian) SPAN (Spanish) 3.0 Measurement System ENG (English) MET (Metric) 4.0 Programmable Function Keys Enter[...]

C-2 A-61097 May 1997 Item Description Values 22.0 Image Address Field Widths 0 – 9 23.0 Level Rules Level 0 Level 1 Level 2 Level 3 24.0 Batching 24.1 Level None Level 1 Level 2 Level 3 24.2 Value 01 – 9999 24.3 Start-of-Batch function f94 (go to Level 1) f95 (go to Level 2) f96 (go to Level 3) 24.4 End-of-Batch function f94 (go to Level 1) f95[...]

A-61097 May 1997 C-3 Item Description Values 36.0 Footswitch Released OFF (Undefined) Level 0 Level 1 Level 2 Level 3 INC (Increment) 37.0 Footswitch Confirmation Tone ON (Enabled) OFF (Disabled) 38.0 Patch Reader 1 ON (Enabled) OFF (Disabled) 39.0 Patch Reader 2 ON (Enabled) OFF (Disabled) 40.0 Patch Definition 40.1 Transfer Patch Definition Level[...]

C-4 A-61097 May 1997 Item Description Values 47.3 Print Definitions Enter item(s) 48.0 Document Printer 12 48.1 Status ON (Enabled) OFF (Disabled) 48.2 Font/Orientation COM (Comic) COM180 (Comic 180) 48.3 Print Definitions Enter template 49.0 Document Sorter 49.1 Status ON (Enabled) OFF (Disabled) 49.2 Error Response DISP (Display) BEEP (Display an[...]

EASTMAN K ODAK COMP ANY Business Imaging Systems Rochester , Ne w Y or k 14650 K od ak, Digital Science, the ds monogram symbol, and Imagelink are tr ademar ks of Eastman K odak Compan y . Printed on recycled paper . B USINESS IMA GING SYSTEMS A-61097 5/97 © Eastman Kodak Compan y , 1997 Printed in U .S.A.[...]