Kodak I7300 manual

User’s Guide A - 61133 Part No. 3E9391 CAT No. 102 2581 i7300 Scanner[...]

Parts of the imaging software are copyrighted by SRZ Berlin. Portions of this product are: Copyright  1990 - 2000 Input Software, Inc. and/or its licensors, 1299 Parkmoor Drive, San Jose, CA 95126, U.S.A. All rights reserved .[...]

EASTMAN KODAK COMPANY SOFTWARE LICENSE AGREEMENT Read the following terms and conditions ca refully before using this Software. Use of this Software indicates your acceptance of these terms and conditions. If you do not agree with them, you should promptly return the package in its entirety for a full refund. LICENSE Grant of License . Eastman Koda[...]

A - 61133 March 2003 1 - 1 1 Introduction The Kodak i7300 Scanner Application Software controls the Kodak i7300 Scanner and the Kodak Digital Science Intelligent Microimage Scanner. The s canner is a 16 mm film retrieval subsystem that is interfaced with a personal computer (PC). The compact film drive and application software enable: • automatic[...]

1 - 2 A - 61133 March 2003 System requirements See the Installation Planning Guide, A - 61405 for software and hardware requirements. Using this man ual This User’s Guide describes the functions and procedures of the Kodak i7300 Scanner Application Software . Chapters 2, 3 and 4 are directed toward individuals who are responsible for retrieving i[...]

A - 61133 March 2003 2 - 1 2 Getting Started The main window This chapter describes the menus, toolbars and Control Panel that are available when using the Kodak i7300 Scanner Application Software. Some menu options , when selected, will perform the action immed iately. Other menu options, those options followed by three dots (…), will display a [...]

2 - 2 A - 61133 March 2003 The Title bar The Title bar provides the title of the Scanner Application Software. The Menu bar The Menu bar provides the following menu options: The following summarizes the functions associated with each menu: File — allows you to open, save and route images, print, fax or e - mail images, access information on the c[...]

A - 61133 March 2003 2 - 3 The File menu The File menu provides the following options: Open Image… — displays the Open Image dialog box, which allows you to open a previously saved image from this application or other applications. You can not open multi - page TIFF files , from File>Open Image . See Chapter 3, Using the Software for more in[...]

2 - 4 A - 61133 March 2003 Fax Setup… — if a fax utility is available on the PC you are using, this option allows you to set up a fax connection. Send as e - mail… — if an e - mail utility (MAPI - compliant) is available on the PC you are using, this option allows you to send an image, selected images or the entire contents of a folder to a[...]

A - 61133 March 2003 2 - 5 The Edit menu The Edit menu provides the following options: Undo — cancels the last edit action. Redo — repeats the last edit ac tion. Cut — removes the selected image or portion of an image from the display and places it on the Windows clipboard. Copy — allows you to copy a complete image or portion of an image t[...]

2 - 6 A - 61133 March 2003 The Annotate menu The Annotate menu provides the following options: NOTE: When using these options, the Annotation toolbox should be displayed which allows you to take advantage of all the options. When applicable to an option, the Annotation toolbox provides the ability to specify color and line width. To display the Ann[...]

A - 61133 March 2003 2 - 7 Select  allows you to edit previously created text, move and/or resize previously created arrows, boxes, etc. Image  displays the Open dialog box, which allows you to select a Windows bitmap image to overlay on the currently displayed image (e.g., Approved, Paid, Canceled, etc), like a rubber stamp. Polyline  all[...]

2 - 8 A - 61133 March 2003 The View menu The View menu provides the following options: Fit Width — allows you to display the image so the entire width of the image fits in the Image display pane. The vertical scroll bar may be required to view the entire length of the image. Fit Height — allows you to displ ay the image so the entire length of [...]

A - 61133 March 2003 2 - 9 Rotated 90 ° Clockwise — allows you to rotat e an image 90 degrees to the right (clockwise). Rotation is based upon the original displayed position of the image. Rotated 180 ° — allows you to rotate an image 180 degrees. Rotation is based upon the original displayed position of the image. Rotated 270 ° Clockwise ?[...]

2 - 10 A - 61133 March 2003 Error Log  displays the Error Log dialog box which shows the messages and errors that occurred for the current scanner session. The messages posted in the Error Log are normal system messages and can be both informational and critical messages. For troubleshooting information regarding these messages, see Chapter 6, T[...]

A - 61133 March 2003 2 - 11 Viewing or hiding View menu options You can view or hide the following features using the View menu: • Toolbar • Control Panel • Annotation Toolbox • Status bar • Documents/Folder pane • Thumbnails pane When a check mark is displ ayed next to the menu option (as shown below), the feature will be visible and a[...]

2 - 12 A - 61133 March 2003 The Customize menu The Customize menu provides the following options: Control Panel  allows you to position the Control Panel to the right or left of the window, or to hide it. Keyboard… — allows you to assign commonly used commands to function keys or a combination of keys. Toolbar… — allows you to specify wh[...]

A - 61133 March 2003 2 - 13 3. Pla ce the cursor in the New Shortcut field and enter the desired shortcut. Valid entries include any individual alphanumeric character or function key used in conjunction with the Ctrl+Alt or Ctrl keys. The function keys can also be used alone. Examples of va lid shortcuts: Ctrl+Alt+S, Ctrl+F11, F8, Shift+F2. NOTES: [...]

2 - 14 A - 61133 March 2003 Unassigning shortcut keys 1. Select the desired menu item from the Menu Entries list box. 2. If None is displayed in the New Shortcut field, click Assign . If a shortcut is displayed in the New Shortcut field, place the cursor in the New Shortcut field and clic k Assign. Press the spacebar. None will be displayed in the [...]

A - 61133 March 2003 2 - 15 To rearrange buttons on the toolbar: 1. Select the button to be moved on the Toolbar Buttons list box. 2. Click on the Move Up or Move Down button . 3. Move as many buttons as desired. 4. When finished, click Close . The button at the top of the Toolbar Buttons l ist box will be the first button on the left if the toolba[...]

2 - 16 A - 61133 March 2003 The Navigate menu The Navigate menu provides the following options: Browse Forward… and Browse Backward… — allows you to automatically browse forward or backward one image at a time through a series of contigu ous images, pausing for a number of milliseconds (of your choice) at each image before moving to the next [...]

A - 61133 March 2003 2 - 17 Batch Scan… — scans a specified group of images , which do not have to be contiguous or continuous. The images must be automatically saved to a directory and/or printed. S ee the section entitled, “Batch scan” in Chapter 3 for more information. Clear  used to clear information from the Image Retrieval keypad t[...]

2 - 18 A - 61133 March 2003 Pause – momentarily stops the film at the selected image until you select Resume . When you select Resume , scrolling will b egin at the image where it left off when Pause was selected . How you process your image is dependent upon how your application is set up. One of the following methods is available: • If your a[...]

A - 61133 March 2003 2 - 19 The Image Processing menu The Image Processing menu provides the following options for the currently displayed image (bi - tonal images only): Despeckle — reduces the amount of no ise and specks, etc . Successive use of the menu will cycle through the values of 0, 1, 2. Deskew — automatically straightens the displaye[...]

2 - 20 A - 61133 March 2003 The CAR menu The CAR menu provides the following options: Setup  allows you to associate a retrieval application with a CAR mode and configure the CAR communicatio n port. Ready  signals back to the CAR system that it is ready to receive downloads, batch downloads or direct commands. Applicable only when using the [...]

A - 61133 March 2003 2 - 21 The Setup menu The Setup menu provides the following options: Application… — displays the Select Application dialog box, which provides access to create a new application(s) and modify or delete an existing application(s). See Chapter 4, Application Setup for more information. Film Controller …  this option is f[...]

2 - 22 A - 61133 March 2003 The Help menu The Help menu provides the following options: i7300 Scanner Help — displays the contents of the Application Software on - line help topics, including men us, procedures, glossary terms and messages. Contents and Index — displays the Help Topics dialog box. The Index tab provides an alphabetic listing of[...]

A - 61133 March 2003 2 - 23 T he Toolbar If the toolbar is not displayed, it can be displayed by choosing View>Toolbar. Procedures on how to use these functions are included in this section or Chapter 3, Using the Software . Most of these options can also be acce ssed from the menus. The following table provides the toolbar options and a brief s[...]

2 - 24 A - 61133 March 2003 Button Description Zoom In — allows you to enlarge the image on the display . Zoom Out — allows you to reduce the image on the display. Fit Width — resizes the image so the entire width of the image fits in the Image display pan e. Fit Window — resizes the image so the entire length and width of the image fits in[...]

A - 61133 March 2003 2 - 25 The Annotation toolbox The Annotation toolbox allows you to specify font attributes, color and line width, when applicable. If the Annotation toolbox is not displayed, it can be displayed by choosing View>Annotation Toolbox. Procedures on how to use these functions are described in Chapter 3, Using the Software . Most[...]

2 - 26 A - 61133 March 2003 Freehand Line  allows you to draw free - form lines. Polyline  allows you to draw a series of line segments by connecting points. Text — allows you to type a text message to be added to the image. Click on Fonts to allow you to select the font type, size and style for the text. This font selection will remain act[...]

A - 61133 March 2003 2 - 27 The Image Retrieval keypad The Image Retrieval keypad is usually displayed at the bottom of the PC monitor. This keypad can be placed anywhere on the screen. To move the Image Retrieval keypad: • Place the mouse cursor on the title bar of the keypad, press and hold the left mouse button and drag the keypad to the desir[...]

2 - 28 A - 61133 March 2003 Clr (Clear) — the Clr button is used to c lear information from the Image Retrieval keypad text box. When Clr is selected, it will also stop any film movement (i.e. searching, refiling, etc.) Set A — when used with the number keys, allows you to: • preset the starting image address for Channel A (e.g., film roll #2[...]

A - 61133 March 2003 2 - 29 The Control Panel All functionality of the Control Panel is described in this section. The Control Panel : Allows you to select an application from the drop - down box. Provides the ability to hide or display the Image Processing control panel. Allows you to hide or display the Scroll/Batch buttons. Provides a status upd[...]

2 - 30 A - 61133 March 2003 Application  allows you to select the desired application from the drop - down list. When an application is selected, all of its de fined parameters immediately become active. NOTE: If there is a roll of film inserted in the scanner when the application is changed, the film will rewind automatically. Show/Hide Image P[...]

A - 61133 March 2003 2 - 31 The Browsing dialog box allows you to pause browsing, specify display time for each image in milliseconds, and change to browsing in the other direction. While paused, image processing changes may be made using the Image Processing Control Panel. • To end browsing, click Close . • The button suspends the browsing fun[...]

2 - 32 A - 61133 March 2003 <<  moves the film rapidly backward , then resume scrolling. <  moves the film slowly backward , then resume scrolling . Pause  momentarily stops the film at the selected image until you select Resume . Film will be repositioned to scroll where yo u left off. >  moves the film slowly forward. >[...]

A - 61133 March 2003 2 - 33 The image processing Control Panel Image processing parameters are setup via the Setup>Application function at the time of installation or by the system administrator. You can temporarily override the original values for an application. The Application Software provides two levels of overriding image processing parame[...]

2 - 34 A - 61133 March 2003 The Image Processing Control Panel allows you to change image processing values to obtain the best image possible for the current application. Changes will remain in effe ct until the application is changed, or the Application Software is exited. Application — select the desired Application from the list box. Show/Hide[...]

A - 61133 March 2003 2 - 35 Scan Area  determines the area of the film that the image processing settings are applied to. • Primary  image processing settings are applied to the entire image area that is defined in the Application Setup. This is the only option avai lable for non - duplex processing. Front and Back are available when Duplex[...]

2 - 36 A - 61133 March 2003 Separate Front and Back  check this option when you want to create two separate image files or prints; one file for the front of the image and one file for the back of the image (see the illustration below). This is useful for printing fron ts and backs on separate sheets of paper. With Separate Front and Back enabled[...]

A - 61133 March 2003 2 - 37 Despeckle — reduces the amount of stray spots (specks, etc.) on an image. This option is for bi - tonal images only. NOTE: The Contrast, Brightn ess and Despeckle options can be roughly adjusted by using the slider bar. You can more precisely adjust these options by entering a value in the entry field or use the up and[...]

2 - 38 A - 61133 March 2003 Border — choose one of the following options: • Leave : keeps the border around the image. • Auto crop : removes the border from around the image. • Border remove : removes the border from around the image but does not reduce the scanned image file size. Border remove works best with images that have proper expos[...]

A - 61133 March 2003 2 - 39 Ove rscan  to enable or disable scanning and display of a specified number of images before and after the image you requested. The Before and After values are defined in Application setup. Overscan is useful for film with poor image al ignment within the film frame, such as 3890 single - level check film. When Oversca[...]

2 - 40 A - 61133 March 2003 ♦ Image Area  allows you to remove and redraw the Image Area green rectangle by clicking outside the rectangle with the left mouse button to remove, then drag - selecting the desired area to redraw. Also allows you to move or resize the rectangle, the same way as the Selection tool. ♦ Previous Block  allows you[...]

A - 61133 March 2003 2 - 41 The Thumbnail pane The Thumbnail pane can be displayed by selecting the View> Thumbnails option. You can display thumbnails as small icons, large icons, a list, or a list with details. Select None to hide the Thumbnail pane. The Application Software is only capable of op ening image files. NOTE: If you want Thumbnails[...]

2 - 42 A - 61133 March 2003 The Status bar The Status bar indicates the application name, the image address of the image that is displayed and whether or not it is in Film or Programmed mode. Informational messages may also be displayed in the Status bar. NOTE: If IMC is enabled in Application setup, and the film currently loaded in the scanner has[...]

A - 61133 March 2003 3 - 1 3 Using the Software After you have reviewed Chapter 2, Getting Started , you will be ready to start using the Application Software . Images can be retrieved from film by using the scanner. This chapter provides pr ocedures for: • Calibrating the scanner • Opening applications • Retrieving images from film • Openi[...]

3 - 2 A - 61133 March 2003 Opening an application The Application Software allows you to select an existing application or create a new application. Chapter 4, Application Setup , provides procedures on setting up new applications. To use an existing application: • Select the desired application from the Applicat ion drop - down list box on the C[...]

A - 61133 March 2003 3 - 3 Searching for next occurren ce of an image address The Search Again function allows you search for the next occurrence of an image address on a roll of film. To use the Search Again function: • Select Navigate>Search Again . The scanner will begin sea rching the roll for another occurrence of the current image addres[...]

3 - 4 A - 61133 March 2003 Searching for a preset image address The scanner is set to count the first image mark on a roll of film as 1 or 1.0 or 1.0.0 (depending on the number of levels in the image address). If the first image on the film has an image addre ss or sequence number other than 1 or 1.0 or 1.0.0, you can use the Set A or Set B functio[...]

A - 61133 March 2003 3 - 5 Batch scan To automatically save and/or print a group of images from the same roll of film, use the Batch Scan option. Before accessing Batch Scan, be sure film is inserted into the scanner and that you have searched to the first image address in the batch. Adjust the images as desir ed, then select Navigate>Batch Scan[...]

3 - 6 A - 61133 March 2003 NOTE: If you want to change the path of the folder where images will be saved, and/or the conventions to be used for naming files, select Setup from the Batch Scan dialog box to display the Setup Naming dialog box. • Enter the path in the r oot directory text box, or click the Change… button to select the desired dire[...]

A - 61133 March 2003 3 - 7 In addition, the character “N” can be used as a wildcard to specify various ranges. For example, in a 3 - level application: • When an image has already been retrieved and is displayed, to enter a r ange for next address to first address in next chapter: - 3.1.n , where 3 is the current book and 1 is the current cha[...]

3 - 8 A - 61133 March 2003 Opening images You may want to open an image that has been previously saved. To do this: 1. Select File>Open Image… . The Open Image dialog box will be displayed: 2. Select the desired directory using the Look In drop - down box and tool buttons. 3. Select the file type from the Files of type drop - down box. 4. Sele[...]

A - 61133 March 2003 3 - 9 Saving an image You can save a previously saved image to another file or save a new image using a non - default film name and/or path by using the Save As option . To do this: 1. Select File>Save As… . The Save As dialog box will be displayed: 2. Enter a new file name. 3. Select the directory where you want the file [...]

3 - 10 A - 61133 March 2003 Printing an image The Application Software allows you to print images individually or group them in folders and print them. A print utility program must be installed for the Print option s to work. 1. Select File>Print . The Print Options dialog box will be dis played. 2. Select the desired printer. You can change the[...]

A - 61133 March 2003 3 - 11 To print a folder of images: 1. Click on the folder to print in the Thumbnail pane with the right mouse button. 2. Select Print from the Popup menu. The images will be printed using the current p rint options. For detailed procedures on how to use the printer software package, see the instructions provided with your prin[...]

3 - 12 A - 61133 March 2003 To fax a folder of images: 1. Select on the folder to fax in the Thumbnail pane with the right mouse button. 2. Sel ect Fax from the Popup menu. The images will be faxed using the current fax options. For detailed procedures on how to use the fax software package, see the instructions provided with your fax software. E -[...]

A - 61133 March 2003 3 - 13 Cropping images Use the Crop option to save or print only the significant part of an image. The area inside the yellow rectangle will be retained and the ar ea outside the rectangle will be removed . Make any desired image processing changes before cropping. To crop an image: 1. Place the mouse cursor at a corner of the [...]

3 - 14 A - 61133 March 2003 2. Retrieve an imag e that you want to duplex process. The Duplex Processing dialog box will be displayed showing the image area defined in Application setup. Selection tool Zooms in on the image area. Zoom Area tool Zooms in on the image area. Image Area tool A ctivates the green rectangle. This tool allows you to draw [...]

A - 61133 March 2003 3 - 15 3. Either a red rectangle or blue rectangle will be automatically displayed, or one green rectangl e, depending on previous actions. • The red rectangle is used to define the front, and the blue rectangle is used to define the back. You can either use the handles to resize the current rectangles or use the Front and Ba[...]

3 - 16 A - 61133 March 2003 5. If you did not get the image area you want, click on the Reproce ss button on the Control Panel to redisplay the Duplex Processing dialog box and repeat the above steps. 6. When the desired results are achieved, select Automatic to apply the duplex processing values to subsequent scans. You can select Front (or Back) [...]

A - 61133 March 2003 3 - 17 Rotat ing an image using duplex processing If you want to rotate an image 90 ° when you are using duplex processing, you can use either the Rotation option on the Control Panel, or select the Rotate toolbar button. Depending on which option/tool you use, the res ults will be displayed differently as shown below: Before [...]

3 - 18 A - 61133 March 2003 Annotating an image The Annotate option allows you to highlight a particular area of an image, blank out information on an image or add a note to an image before printing, faxing or saving. You can use this feature to mask confidential information or add a customer message on a requested image. NOTES: • The Ellipse opt[...]

A - 61133 March 2003 3 - 19 Using the Text option To add text to your image : 1. Select Annotate>Text. 2. You can change the color and/or font on th e message by using the color palette and Font button on the Annotation Toolbox. 3. Click the left mouse button to place the cursor where you want to add a text message. 4. Type the desired message. [...]

3 - 20 A - 61133 March 2003 Loading images Use the Load Image… option to load a different image file into memory. 1. Select Annotate>Load Image… . The Load Image dialog box will be displayed: 2. Select the desired directory. 3. Select the file type from the Files of type drop - down box. 4. Select the image file you want, or enter the file n[...]

A - 61133 March 2003 3 - 21 Creating a canned annotation file The Canned option allows you to save annotation created for an image, for use on other images. This option is useful if you have many images that you want to apply the same annotation information to. 1. Retrieve an image. 2. Using the Annotation Toolbox and tools, create the desired anno[...]

3 - 22 A - 61133 March 2003 Using canned annotations Once you have created annotation files, you can use the information in the annotation files to add the same information on other images. To do this: 1. Retr ieve the image you want to annotate. 2. Select Annotate>Canned>Load . The Open Canned Annotations dialog box will be displayed: 3. Sel[...]

A - 61133 March 2003 3 - 23 Deleting annotation To delete annotation: 1. Select Annotate>Select , and click on the annotation you want to delete. 2. Press the DEL (delete) key on the PC keyboar d. The annotation will be deleted. Resizing the application window The Application window can be resized. To do this: 1. Start the Application Software. [...]

3 - 24 A - 61133 March 2003 Deleting annotation To delete annotation: 1. Select Annotate>Select , and click on the annotation you want to delete. 2. Press the DEL (delete) key on the PC keyboard. The annotation will be deleted. Resizing the application wi ndow The Application window can be resized. To do this: 1. Start the Application Software. [...]

A - 61133 March 2003 4 - 1 4 Application Setup This chapter provides the following: • How to access the Application Setup option. • Procedures for setting up a new application. • Procedures for modifying and deleting existing applications. Kodak provides predefined applications, for more information see Appendix D, Productivity Tools . Access[...]

4 - 2 A - 61133 March 2003 Setting up a new application The Setup Application dialog box allows you to predefine retrieval and image processing parameters for a specific application. Click on each tab to set all the desired values. Do not click OK until you have made all of your selections on all of the tabs. All tabs on the Setup Application dialo[...]

A - 61133 March 2003 4 - 3 2. Search Program . Select the Search Program based upon the image marks on film you will be searching. These search programs are identified in Appendix B, Search Programs. Be sure the correct program is selected to match the film index format and image mark location channel. An odomet er mode search program is also avail[...]

4 - 4 A - 61133 March 2003 Determining the threshold value Follow the procedure below to determine the threshold value. • Disable Auto Back Removal. • Set up your application with the options that you will be using with Auto Back Removal (i.e. auto cropping, scan output types, etc.). • Insert a roll of film that you want to use the Auto Back [...]

A - 61133 March 2003 4 - 5 Setting values on the Image Marks tab Use the Image Marks tab to define the type of image marks on the film associated with the application you are setting up. Do not click OK until you have made all of your selections on all of the tabs. 1. Select the Image Marks tab. 2. Image Marks. Select the type of image marks on the[...]

4 - 6 A - 61133 March 2003 3. Image Mark Position . Select the image mark position on the film. • Choose Lead Edge if the image marks are a ligned with the lead edge of the image. • Choose Other if the image marks are located in any other position than the lead edge and then select Setup… to display the Image Mark Position dialog box. See the[...]

A - 61133 March 2003 4 - 7 7. Preset . The Preset option is used when the image address begins at something other than one (1). • If Set to First image address is enabled, the preset image address will be assigned to the first image mark on the film. • If Set to First image address is disabled, the preset image address assigned to the first ima[...]

4 - 8 A - 61133 March 2003 Setting values on the Film tab The film format and reduction ratio of the images on film can be defined using the Film tab. Do not click OK until you have made all of your selections on all of the tabs. 1. Select the Film tab on the Setup Application dialog box. 2. Film Format . Select the Film Format from the list box: ?[...]

A - 61133 March 2003 4 - 9 3. Film Reduction. Select the Film Reduction ratio for the film used. It is important that this value be accurate to achieve the correct print size results. Select a value from 1 to 59. 4. Overscan . If desired, select a value in the Images Before and/or Images After list boxes. Overscan is intended for use with single - [...]

4 - 10 A - 61133 March 2003 The User defined option pro vides the greatest efficiency and flexibility in choosing the image area that meets your specific application needs since it allows you to customize the image area. If you select User defined , the Setup… button will be activated. Click Setup… to display t he Select Image Area dialog box. [...]

A - 61133 March 2003 4 - 11 9. Border Removal Recursions : the number of times (one, two or three) the system will attempt to determine and remove the boundaries of the image. Three is the default. Longer processing times are required for each attempt. Even though you may enter a value of 3 in this field, the system may remove the border the first [...]

4 - 12 A - 61133 March 2003 Setting values on the Image Processing tab The options on the Image Processing tab are selected based upon how you want to alter the image. Do not click OK until you have made all of your selections on all of the tabs. 1. Select the Image Processing tab to set the image processing values.[...]

A - 61133 March 2003 4 - 13 2. Scan Area . Select an option in the Scan Area. This option determines the area of the film that the image processing settings are applied to. • Primary  applies to the image area that is defined in the Application setup . Use Front and Back for duplex processing applications: • Front  select Front if you wan[...]

4 - 14 A - 61133 March 2003 4. Separate Front and Back  check this option when you want to create two separate image files; one file for the front of the duplex image and one file for the ba ck of the image (see the illustration below). This is useful for printing fronts and backs on separate sheets of paper. With Separate Front and Back enabled[...]

A - 61133 March 2003 4 - 15 6. Contrast . Select a Contrast setting from Low ( ) to High ( ) or enter the contrast value in the text field. Valid values are 0 to 255. For gray scale images only. • A low contrast value produces a scanned output of mostly midtones (more subtle change in gray levels are detected). • A high contrast value produces [...]

4 - 16 A - 61133 March 2003 11. Rotate . Select a Rotate option to specify whether images will be rotated when displayed: • None : to process the image in the original orientation. • 90° Clockwise : to process the image rotated 90° to the right. • 180° Clockwise : to process the image rotated 180° to the right. • 270° Clockwise : to pr[...]

A - 61133 March 2003 4 - 17 16. Auto Deskew . Check Auto Deskew to automatically straighten the image NOTE: When using the Auto Deskew option , the entire image (all borders) need s to be visible in the image area so the i mage can be captured properly. 17. Overscan . Check the Overscan option to enable scanning and display of a specified number of[...]

4 - 18 A - 61133 March 2003 Setting values on the Output tab The Output tab allows you to set up file saving options, compression level and how you want the i mage to be printed, faxed or emailed. 1. Select the Output tab. 2. File Saving Options . If you want to save images to a non - default location and/or file names, select Change… . The Namin[...]

A - 61133 March 2003 4 - 19 See the section entitled, “Changing naming convention properties” late in this chapter for more information. • Annotation Imbedded : when this option is enabled, any annotation that is included with an image will become part of the image bitmap. NOTE: If this option is not selected and the image is saved in TIFF fo[...]

4 - 20 A - 61133 March 2003 Changing naming convention properties The Naming Convention Properties dialog box allows you to change the file naming rules and the root directory where images will be saved. From the Output tab: From the Output tab: 1. Select Change… from the File Saving Options . The Naming Convention Properties dialog box will be d[...]

A - 61133 March 2003 4 - 21 The image address can be part of the name given to the image. Special keywords are used in this fiel d by default, they are: book (level 3), chapter (level 2), image (level 1) and area (determines whether the value in Primary , Front and/or Back in the Areas section) is included in the file names. NOTE: Front and Back va[...]

4 - 22 A - 61133 March 2003 Example 2  using no optional parameter If the file naming convention was set to <book>.<chapter>.<image><area>.tif, the resulting image file name would be as follows if the current image address is 10.14.145: • If Se parate Front and Back is not enabled on the Image Processing tab, and Areas [...]

A - 61133 March 2003 4 - 23 Setting up non - ANSI/AIIM image marks If the film you are retrieving images from has image marks that do not meet the ANSI standards because the film was created by a non - Kodak microfilmer, use the Other… option on the Image Marks tab to define the image mark size. 1. Select Other . 2. Click Setup to display the Ima[...]

4 - 24 A - 61133 March 2003 Determining the image mark position The scanner requires that the leading edge of the image marks be located even with the leading edge of the document images . Some microfilmers place image marks after the leading edge of document images. The Image Mark Position enables you to work with image marks that have been p lace[...]

A - 61133 March 2003 4 - 25 Setting up the odometer scale Some older microfilms are indexed wit h odometer units instead of image marks. The scanner can search odometer film as well as film with image marks. To set an odometer unit: From the Image Marks tab: 1. Select Odometer Scale Setup… The Odometer Scale dialog box is displayed: 2. Enter a va[...]

4 - 26 A - 61133 March 2003 Setting a User Defined image area When you are setting film parameters and you want to define a custom image area, use the Setup option on the Film tab. From the Film tab: 1. Select User defined from the Image Area drop - down list. 2. Click Setup… to display the Select Image Area dialog box . 3. Load the film in the s[...]

A - 61133 March 2003 4 - 27 Setting page layout options The Page Layout dialog box provides options which allow you to position the displayed image where you want on a sheet of paper for printing, faxing or emailing. You can also add annotation to every page automatically. From the Output tab : 1. Select Page Layout Setup … The Page Layout dialog[...]

4 - 28 A - 61133 March 2003 3. Units : Select either 1/10 Inch or Millimeter . The unit measurement is based on paper size, not how the image is displayed on the screen. 4. Simplex/Duplex Front : select a value for image placement on the paper. The value you enter is equal to 1/10 of an inch (or millimeters, depending on how your system is set up).[...]

A - 61133 March 2003 4 - 29 The following table provides the maximum values of paper width and length: Units = 1/10 inch Maximum Units = Millimeters Max imum Image Size Length Width Length Width Letter 110 85 279 216 Legal 140 85 356 216 Ledger 170 110 432 279 8.5 x 5.5 85 55 216 140 A3 165 117 420 297 A4 117 83 297 210 A5 83 58 210 148 A6 58 41 14[...]

4 - 30 A - 61133 March 2003 6. Image Scale Options : • Fit on page : scales the displayed image to fit on the defined page size. The resulting resolution of the final image * will be the same as what was defined by the combination of R eduction setting (on the Fil m tab) and defined Image size (on the Output tab) . For example, a reduction setti [...]

A - 61133 March 2003 4 - 31 6. Annotation Position : enter your text annotation in the Text box and set the Upper Corner and Left Corner position as to where you want the annotation to appear on every image. Your text message will appear on every image within the batch in the designated location. Typically annotation is positioned at the top or bot[...]

4 - 32 A - 61133 March 2003 Modifying an existing application Modi fying applications is similar to creating a new application. Refer to the previous section entitled “Setting up a new application” if you need a description of the fields on the tabs. To modify an application : 1. Select Setu p>Application . The Select Application dialog box [...]

A - 61133 March 2003 4 - 33 Deleting an application Existing applications can be deleted by using the Select Application dialog box. To delete an application: 1. Select the application you want to delete from the Application drop - down li st box. 2. Click Delete . The following message will be displayed: 3. Click Yes to delete the selected applica[...]

A - 61133 March 2003 5 - 1 5 Setting up CAR Applications This chapter provides procedures that allow you to use CAR applications with the scanner. If you have purchased CAR functionality and if CAR does not appear on the menu bar, call Kodak service. The scanner can accept image ad dresses, commands and text messages from a Computer - Aided Retriev[...]

5 - 2 A - 61133 March 2003 Setting up CAR commun ication and modes Before you begin processing CAR commands , CAR communication and modes should have previously been set up. It is suggested that you record these sett ings, in case you need to change them for some reason. Setting up CAR communication To set up CAR communication: 1. Select CAR>Set[...]

A - 61133 March 2003 5 - 3 Changing the CAR communication settings If you need to change any of the settings listed on the Setup CAR Communication dialog box. If you change these settings, the Bits per second, Data bits , Parity and Stop bits must match the s ame settings defined on the CAR system. To change the CAR communication settings: 1. Selec[...]

5 - 4 A - 61133 March 2003 Setting up CAR modes Setting up CAR modes is a way to allow a remo te CAR host to change values in the application parameters. This function is used primarily to support the A , B , and D commands. To set up CAR modes: 1. Select CAR>Setup>Modes… from the main screen. The Setup CAR Modes dialog box will be displaye[...]

A - 61133 March 2003 5 - 5 Processing Download requests The Download menu allows you to start and stop downloads, batch downloads and direct search transmissions. It also allows loading of previously saved download a nd batch download files to the scanner memory registers. Diagnostic capability is provided through the Dump menu options. Starting an[...]

5 - 6 A - 61133 March 2003 Dumping jobs Occasionally it may be necessary to view the data that is sent by the host computer and analyze it. The Dump menu options are intended for diagnostics , not everyday operation. The following options are provided: View Dump…  allows you to view the data that is sent by the CAR host computer to the scanner[...]

A - 61133 March 2003 5 - 7 CAR registers The Registers menu allows you to save or view what is currently loaded in the registers, or load a previously saved file to the registers. You can also start a batch download using the Registers function. Saving and loading registers The Save and Load functio ns are primarily used for diagnostic purposes. To[...]

5 - 8 A - 61133 March 2003 To load the registers with a previously saved file: 1. Select CAR>Registers>Load . The Load Register File dialog box will be displayed: 2. Locate and select the desired file. 3. Click Open . Starting a Batch download and using View registers During a batch download, commands, text messages, and image addresses are l[...]

A - 61133 March 2003 5 - 9 Using the View Registers function The CAR Register s dialog box allows you to change the order in which a download is executed. Following is a summary of the functions available on the CAR Registers dialog box. Start Register  displays the next reg ister to be executed. Exec. Register  displays the register currentl[...]

5 - 10 A - 61133 March 2003 Changing the starting register: 1. Select CAR>Registers>Vie w . The CAR Registers dialog box will be displayed: 2. Highlight the register from the list box where you want to start at and double - click the mouse button. 3. Click Start . 4. Click OK to close the CAR Registers dialog box. CAR monitor The CAR Monitor [...]

A - 61133 March 2003 6 - 1 6 Troubleshooting Software advisory messages This chapter contains information on software - advisory messages that may occasionally arise while using the Kodak i7300 Scanner Application Software . These codes are usually informational messages and often req uire no action. Hardware - related messages can be found in the [...]

6 - 2 A - 61133 March 2003 Problem solving Use the chart below as a guide to check possible solutions to problems you may encounter when using the Scanner Application Software. Problem Possible Solut ion Large batch - related messages /problems Image not found This is a normal message when running a large batch. Image not found indicates that the b[...]

A - 61133 March 2003 7 - 1 7 Network Operations One or more scanners can be networked with Kodak Image Server Software. Image Server Software is a background process software application, which runs on a separate PC. It provides an integral component of a larger system of Kodak and i ntegrator - supplied micrographics devices and applications that [...]

7 - 2 A - 61133 March 2003 The Image Server dialog box provides the ability to connect to a dispatcher installed on the local or remote PC. The r emote PC name can be specified. The local PC name is provided automatically. The Status field will indicate whether a dispatcher is connected or disconnected. If the Scanner Application Software was conne[...]

A - 61133 March 2003 7 - 3 Connecting to a VNN The Image Server Software contains from 1 to 4 virtual network nodes (VNN) . Each VNN operates discretely from the others. The scanner must be connected to a VNN to utilize the features of the Image Server Software. Th e Image Server option from the Navigate menu provides the capability to connect the [...]

7 - 4 A - 61133 March 2003 2. Enter the name of the VNN you want to connect to. This name must be entered exactl y as it is defined on the Image Server Software, including upper and lower case letters. NOTE: If an incorrect node name is entered, the message Node not found will be displayed when OK is selected. 3. Select the type of output device fr[...]

A - 61133 March 2003 7 - 5 Storing images in a VNN A VNN within the Image Server Software can store scanned microfilm images as documents in folders for later printing, faxing or emailing. A document consists of one or more scanned images from a scanner, held in a folder o n a VNN. Document names may be assigned when connecting to a VNN . The assig[...]

7 - 6 A - 61133 March 2003 Printing individual images To print an individual image immediately: 1. If not already connected, connect to a VNN and First Printer or Second Printer via the Navigate>Image Server>Connect… menu option. 2. If desired, select the bin to output your images to. Your printer bin must be enabled. 3. Retrieve the desire[...]

A - 61133 March 2003 7 - 7 4. Select Navigate>Image Server>Print Chapter from the menu. • If you are using Level 1 film, the requested image and every subsequent imag e to the end of the film will be printed. • If you are using Level 2 or Level 3 film and the requested image is a chapter level or page level image, the requested image and [...]

7 - 8 A - 61133 March 2003 Printing foldered images To organize multiple individual images as a document in a folder for later printing as a folder : 1. If not already connected, con nect to a VNN and Storage Printer via the Navigate>Image Server>Connect… menu option. 2. Specify a folder name and an optional document name. 3. Retrieve the f[...]

A - 61133 March 2003 7 - 9 To add another document to an existing folder : 1. If not already connected, connect to the desired VNN and storage printer via the Navigate>Image Server>Connect… menu option. 2. Specify the existing folder name and a new document name. NOTE: If you are already connected to the VNN and folder, enter a new document[...]

7 - 10 A - 61133 March 2003 The Fax/eMail dialog box The Image Server Software provides fax capability and email c apability. When you are connected in the host software as Fax/eMail, the Fax/eMail dialog box will be displayed after an image is retrieved and displayed. When you are connected as Storage Fax/eMail, the Fax/eMail dialog box will be di[...]

A - 61133 March 2003 7 - 11 To include a delay for the d ial tone in the Fax Number/eMail field (as when dialing 9 for an outside line), use one or more commas (,) as shown in the table below. Each comma causes a 1.5 second delay. Number of commas = Delay time (seconds) 1 1.5 2 3.0 3 4.5 4 6.0 5 7.5 6 9.0 7 10.5 8 12.0 9 13.5 10 15.0 • Both upper[...]

7 - 12 A - 61133 March 2003 • Enable Fax Header Page if you want the header page printed along with your fax. The default is no Fax Header Page. • The fax will be delivered when you send it if you do not enable the Time option and enter a specific time. • The fax will be delivered when you send it if you do not enable the Date option and ente[...]

A - 61133 March 2003 7 - 13 5. Click OK when finished. 6. Optionally disconnect when finished via Navigate>Image Server> Disconnect. Faxing or emailing foldered images To organize multiple i ndividual images as a document in a folder, then fax or email the folder: 1. If not already connected, connect to a VNN and Storage Fax/eMail via the Nav[...]

7 - 14 A - 61133 March 2003 5. Select Navigate>Image Server >Fax/eMai l Existing Folder from the menu. 6. Fill in the necessary information in the Fax/eMail dialog box. (See the section entitled “The Fax eMail dialog box” in this chapter.) 7. Click OK when finished. 8. Optionally disconnect when finished via Navigate>Image S erver> [...]

A - 61133 March 2003 A - 1 Appendix A Microfilm Information Introduction This appendix contains information that will be helpful when operating the Kodak i7300 Scanner or Kodak Intelligent Microimage Scanner . Some of the information is general, while some of it supports specific op erating procedures. This appendix contains information on: • Gen[...]

A - 2 A - 61133 March 2003 Image mark sizes The scanner can accept a set of three customer - specified image mark sizes in the overall range of 0.024 to 0.310 inches (0.61 to 7.87 mm). Image mark sizes can be specified in the machine setup. Small mark Medium mark Large mark Min 0.024 in (.61 mm) 0.085 in (2.16 mm) 0.165 in (4.19 mm) Image Length* A[...]

A - 61133 March 2003 A - 3 Loading film The scanner is designed to offer optimum performance with ANSI magazines ( Ko dak Ektamate Magazines, or equivalent, and Kodak Ektamate A Magazines). In addition, the scanner accepts M - type magazines and enclosed ANSI magazines. Enclosed ANSI magazines may experience reduced threading performance when compa[...]

A - 4 A - 61133 March 2003 Enclosed ANSI magazines IMPORTANT: Enclosed ANSI magazines must be used with solid flange reels designed specifically to fit with these magazines. Standard ANSI film reels designed for open ANSI magazines may cause film transport performance problems when used in an enclosed magazine. To insert the reel into the magazine [...]

A - 61133 March 2003 A - 5 M- type magazines To insert the reel into the magazine : • Orient the magazine as shown in the illustration. Remove the two retainer screws and set them aside. Separate the two parts of the magazine. • Place the film into the magazine with the film feeding counterclockwise off the reel. • Place the two parts of the [...]

A - 6 A - 61133 March 2003 The amount of film on the reel should not go past the arrows indicated on the reel; ther e should be at least a ¼ - inch distance from the edge of the reel to the film. For correct feeding of film on and off the reel without binding or damaging the film: • Pass the film in and out between the flanges (sides) of the ree[...]

A - 61133 March 2003 A - 7 Film leader — M - type magazine When using an M - type magazine , a 31.5 in. (800 mm) leader must be affixed to the film. The following criteria should also be met: • The leader must be square to the attached film. • The first film images should not be closer than 16 i n. (400 mm) from the leader - film splice locat[...]

A - 8 A - 61133 March 2003 Film trailer — M - type magazine When using an M - type magazine , use a trail end holder to fix the film end to the supply reel. The following criteria should also be met. • Be sure to wind the film onto the supply reel in the correct direction. • The film trailer must be at least 31.5 in. (800 mm) long. • There [...]

A - 61133 March 2003 A - 9 • Make sure there is minimal skew (a slanted cut leaving an angled gap) between the leader tape and film. The skew should be no more than 0.002 in./in. (0.05 mm/mm). • The thickness of the connecting section should be no more than 0.014 (0.38 mm). Film curl For most fil m types and operating conditions, a certain amou[...]

A - 10 A - 61133 March 2003 Film Curl  Ektamate Cartridge[...]

A - 61133 March 2003 A - 11 Film Curl  M Cartridge Curl should be less than 70 when toward roll; less than 40 when away from roll Away Toward 9 0 80 70 60 50 30 40 50[...]

A - 12 A - 61133 March 2003 Film twist Besides curl , the film should also be checked for twist. To make sure that the film’s twist is within allowable limits: • Allow about 12 in. (305 mm) of film to hang down from the reel. • If the film twists more than 90° in either direction, a leader should be attached . Film twist 90° maximum (either[...]

A - 61133 March 2003 A - 13 Film magazine condition The condition of the film magazine is another factor affecting optimum performance of the scanner. Film magazine conditions should meet the following criteria: • The film magazine must not be dist orted in shape (either closed downward or stretched outward). • The film magazine's internal[...]

A - 14 A - 61133 March 2003 Microfilm storage Microfilm should always be handled and stored with care. Storage of your film should be based on the following: • How long you want to keep the images on the microfilm: short, medium, long term, or permanently. • How diff icult the images are to replace. • The cost of preserving the microfilm. For[...]

A - 61133 March 2003 B - 1 Appendix B Search Programs You have a choice of 30 search programs to count image marks. These programs are identified in tables on the following pages. Selecting a search program To select the appropriate search program: 1. Look at the film t o see which channel(s) contain(s) image marks. 2. Determine the size(s) of imag[...]

B - 2 A - 61133 March 2003 When you have the information from Steps 1 - 3, select the appropriate search program table on the following pages. • Table B - 1 is for simplex or duplex film with image marks in Channel A only. • Table B - 2 is for simplex or duplex film with image marks in Channel B only. • Table B - 3 is for duo film (the image [...]

A - 61133 March 2003 B - 3 Image marks in Channel A only NOTE: The film can be simplex or duplex (duplex is shown in the illustration). Table B - 1 Image Marks in Channel A only Image mark size Image mark size Ima ge mark size Search program Number of levels Small 3 1 Medium 5 1 Large 25 1 All sizes of image marks 7 1 Medium Small 10 2 Large and Me[...]

B - 4 A - 61133 March 2003 Image marks in Channel B only NOTE: The f ilm can be simplex or duplex (duplex is shown in the illustration). Table B - 2 Image Marks in Channel B only Image mark size Image mark size Image mark size Search program Number of levels Medium 6 1 All sizes of image marks 9 27* 1 1 Medium Sma ll 14 2 Large Medium Small 20 3 * [...]

A - 61133 March 2003 B - 5 Image marks in both Channels: duo film In these films, the image mark sequence continues from Channel A to Channel B (see the following illustration ). You can reduce search time by setting the last image address in Channel B by using the keypad or by Image Management Code on the film. With the last image address identifi[...]

B - 6 A - 61133 March 2003 Image marks in both Channels: simplex or duplex film In these films, the image mark sequence does not continue from Channel A to Channel B (Simplex film is shown in the following illustration). Both channels are searched simultaneously from the beginning of the film to the end of the film. Table B - 4 Image marks in both [...]

A - 61133 March 2003 C - 1 Appendix C Glossary Application  contains all the software parameters that will allow images to be easily searched, processed and delivered to the PC. Auto - Crop  automatically removes the border of an image. Auto Deskew  automatically straightens the displayed image. Batch  a finite number of documents or im[...]

C - 2 A - 61133 March 2003 Duplex Microfilm — contains images of both the front and back of each document, exposed in one pass through the microfilmer. Folder  consists of one or more documents . Each folder must have a unique name assigned to it when connecting to a VNN . A specified folder and document remains as the output destination until[...]

A - 61133 March 2003 C - 3 Lead End Code — exposed by the microfilmer on a roll of film before any other code. It appears only after the recommended threading leader, and before Preset Code. It contains: • Start character • Roll number • Mode modifiers • Image offset • Magnification • Image polarity • Stop character MAPI  Microso[...]

C - 4 A - 61133 March 2003 Plus Indexing — the capability of the scanner to advance across chapter boundaries. Portrait — image or paper orienta tion in the shape of a conventional portrait, where height is greater than width. Postset Code — See Trail End Code. Preset — setting the image counters of the scanner to a specified value. The ima[...]

A - 61133 March 2003 D - 1 Appendix D Productivity Tools Introduction This appendix provides information regarding two batch files contained on the CD that is packed with the scanner. The files are located in the Product Software directory found in the Application Software directo ry on the CD. These two files facilitate specification of keyboard s[...]

D - 2 A - 61133 March 2003 Application setup templates The application setup templates represent combinations of parameter values that have been found to provide the best retrieval results for several typical film types. The templates are documented below including explanations of the various settings. Template 1  3890 Check film This template i[...]

A - 61133 March 2003 D - 3 3. File Naming Convention: The scanner uses C: IMAGES as the default root directory for saving image files. This may be changed if desired by using the Change button on the Output tab. File naming conventions must also be specified. File names can include a prefix (i.e., ABC as shown in the example below). To change the[...]

D - 4 A - 61133 March 2003 3890 film, Image Marks tab template settings The informatio n below includes only the values that are different from the system default settings. For more information about the Image Marks tab, see the section entitled “Setting values on the Image Marks tab“ in Chapter 4 . Template specific settings • Image Marks: O[...]

A - 61133 March 2003 D - 5 3890 film, Film tab templat e settings The information below includes only the values that are different from the system default settings. For more information about the Film tab, see the section entitled “Setting values on the Film tab” in Chapter 4 . Template specific set tings 1. Film – Format: Duplex . 2. Film ?[...]

D - 6 A - 61133 March 2003 3890 film, Image Proces sing tab template settings The information below includes only the values that are different from the system default settings. For more information about the Image Processing tab, see the section entitled “Setting values on the Image Processing tab” in Chapter 4 . When Duplex Processing is enab[...]

A - 61133 March 2003 D - 7 Explanation of s ettings (see the illustration that follows) 1. Scan Area: • When Primary is selected, the same image processing settings will be applied to both front and back. • When Film View is selected, the image processing settings will be applied in the Select Overscan an d Duplex Processing dialog boxes as wel[...]

D - 8 A - 61133 March 2003 Template 2  County Land Title film This template is recommended when retrieving County Land Title images that were captured to film (24X reduction) using planetary or rotary microfilmers, or the Kodak i9600 Series Writer. County Land Title film, General tab template settings The information below includes o nly the val[...]

A - 61133 March 2003 D - 9 County Land Title film, Image Marks tab template settings The Image Marks tab uses all system default settings. For more information about this tab, see the section entitled “Setting values on the Image Marks tab” in Chapter 4 . County Land Title film, Film tab template settings The information below includes only the[...]

D - 10 A - 61133 March 2003 County Land Title film, Image Processing tab template settings The information below includes only the values that are different from the system default settings. For more information about the Image Processing tab, see the section entitled “Setting values on the Image Processing tab” in Chapter 4 . Template specific[...]

A - 61133 March 2003 D - 11 Template 3  Claims 2 - level film This template is recommended when retrieving cl aims or insurance images from 2 - level film (40X reduction). Claims 2 - level film, General tab template settings The information below includes only the values that are different from the system default settings. For more information a[...]

D - 12 A - 61133 March 2003 Claims 2 - level film, Image Marks tab template settings The Image Marks tab uses all system default settings. For more information about this tab, see the section entitled “Setting values on the Image Marks tab” in Chapter 4 . Claims 2 - level film, Film tab template settings The information below includes only the [...]

A - 61133 March 2003 D - 13 Claims 2 - level film, Image Processing tab template settings The information below includes only the values that are different from the system default settings. For more information about the Image Processing tab, see the section entitled “Setting values on the Image Processing tab” in Chapter 4 . When Duplex Proces[...]

D - 14 A - 61133 March 2003 3. Sharpening: • Photo & Text provides the best clarity for fron t side images since they usually contain non - text information. • Text provides the best clarity for back side images since they usually contain text only. 4. Film Image Quality: improves the contrast of the image.[...]

A - 61133 March 2003 D - 15 Template 4  Claim s 3 - level film This template is recommended when retrieving claims or insurance images from 3 - level film (40X reduction). This template is identical to Template 3 except for the changes indicated below. Claims 3 - level film, General tab template settings T he information below includes only the [...]

D - 16 A - 61133 March 2003 Template 5  Odometer film This template is recommended when retrieving images that were captured to film (24X r eduction) without image marks, using planetary or rotary microfilmers. Odometer film, General tab template settings The information below includes only the values that are different from the system default s[...]

A - 61133 March 2003 D - 17 Odometer film, Image Marks tab template settings The information below includes only the values that are different from the system default settings. For more information about the Image Marks tab, see the section entitled “Setting values on the Image Marks tab” in Chapter 4 . Template specific settings • Image Mana[...]

D - 18 A - 61133 March 2003 Odo meter film, Film tab template settings The information below includes only the values that are different from the system default settings. For more information about the Film tab, see the section entitled “Setting values on the Film tab” in Chapt er 4 . Template specific settings 1. Film – Reduction: 24 . 2. Im[...]

A - 61133 March 2003 D - 19 Odometer film, Image Processing tab template settings The information below includes only the values that are di fferent from the system default settings. For more information about the Image Processing tab, see the section entitled “Setting values on the Image Processing tab“ in Chapter 4 . Template specific setting[...]

EASTMAN KODAK COMPANY Document Imaging Rochester, New York 14650 Kodak, Imagelink and Ektamate, are trademarks of Eastman Kodak Company. Printed on recycled paper. A - 61133 3/2003 CAT No. 102 2581 © Eastman Kodak Company, 2003 Printed in U.S.A. DOCUMENT IMAGING[...]