LevelOne LevelOne 8+8 POE 10/100 Mbps Web Smart Switch manual

LevelOne FSW-1670TX 8+8 POE 10/100 Mbps Web Smart Switch User’s Manual[...]

[...]

i TABLE OF CONTENT About This Guide ....................................................................... 1 Purpose .................................................................................. 1 Terms/Usage .......................................................................... 1 Introduction .............................................[...]

ii Installing the Web M anagement Utility ................................. 15 Discovery List ....................................................................... 16 Monitor List ........................................................................... 17 Device Se tting ...................................................................... 19[...]

1 ABOUT THIS GUIDE Congratulations on your pu rchase of the FSW-1670TX 8+8POE 10/100Mbps Web Smart Switch. This Switch integrates 100Mbps Fast Ethernet and 10Mbps Etherne t network capabilities in a highly flexible pa ckage. Since this switch’s Port- 1 to Port-8 is Power over Et hern et (PoE) ports, it will automatically detect the presen ce of I[...]

[...]

3 INTRODUCTION This chapter describes the features of the FSW-1670TX 8+8POE 10/100Mbps Web Smart Switch and some b ackground information about Ethernet/Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs an d the increasing complexity of desktop computing applications are fueling the nee d for high performanc[...]

4 Switching Technology Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology. A switch bridges Ethern et packets at the MAC address level of the Ethernet protocol transmitting among conne cted Ethernet or Fast Ethernet LAN segments. Switching is a cost-effectiv e way of increasing the total [...]

5 VLAN (Virtual Local Area Network) A VLAN is a group of end-station s that are not constrained by their physical location and can communicate as if a common broadcast domain, a LAN. The pr imary utility of using VLAN is to reduce latency and ne ed for routers, using faster switchin g instead. Other VLAN utility includes: Security, Security is incr[...]

6 separate electrical wirin g and power outlets. Features  16×10/100M bps Auto-negotiation Fast Ethernet RJ45 ports with 8- port PoE function (port-1 ~ port-8)  Compliant with IEEE 802.3af specific ation  Supports PoE power maximum 15.4W for each PoE p ort s  Supports PoE Powered Device (PD) classific ation identify  Each port suppo[...]

7 UNPACKING AND INSTALLATION This chapter provide s unpacking and installation information fo r the Switch. Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents. The carton shoul d contain the following items:  FSW-1670TX 8+8POE 10/100Mb ps Web Smart Switch  One AC power cord  Four rubber feet pad s  Rack[...]

Install the Switch on a sturdy, le vel surface that can support its weight, or in an EIA standard-size equipment rack. For information on rack instal lation, see the next section, Ra ck Mounting . When installing the S witch on a level surface, attach the rubbe r feet to the bottom of each device. The rubber feet cushion the hub and protect the hub[...]

9 Connecting Network Cable The Switch support 16 10/100M Ethernet ports and Port 1 ~ port 8 are PoE Enable ports, these P oE port will automatically activated when a compatible terminal is identified, the Switch will supply power through the Et hernet port to the connected PoE device. For the Legacy devices that are not y et compatible, the PoE por[...]

[...]

IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel , rear panel, and LED indicators of the Switch. Front Panel The figure below shows the front panel of the Switch. Figure 3. Front panel of the Switch LED Indicator: Comprehensive LED indicators di splay the status of the switch and the network (see the LED Indicato rs chapter be[...]

Card) or switch and hub. Ethernet Ports (Port 9~16): These ports support network speed s of either 10Mbps or 100Mbps, and can operat e in half- and full- duplex transfer modes. These ports also suppo rts automatic MDI/MDIX crossover detection fun ction gives true “plug and play” capability, just need to plug-in the network cable t o the hub dir[...]

UNDERSTANDING LE D INDICATORS The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. Figure 5. LED indicators of the Switch Power and System LEDs POWER: Power Indicator On : When the Power LED lights on, the Switch is receiving power. Off : When the Power turns off or the po wer cord has improper con[...]

14 100Mbps On : When the 100Mbps LED lights on, the respective port is connected to a 100Mbps Fast Ethernet network. Off : When the respective port is connected to a 10Mbps Ethernet network PoE Status Green : When the PoE device was connected and the port supplies power successfully. Red : When the PoE port have the following failure happens:  P[...]

15 CONFIGURATION Through the Web Bro wser you can configure the Switch such as VLAN, Trunking, and QoS… etc. With the attached Web Management Utility, you can easily discover all the Web Management Switch, assign the IP Address, changing the password a nd upgrading the new firmware. Installing the Web Management Utility The following gives instru[...]

Figure 6. Web Management Utility The Web Management Utility was divided into four parts, Discovery List, Monitor List, Device Setting and Toolbar function , for details instruction, follow the below secti on. Discovery List This is the list where you can di scover all the Web management devices in the entire network. By pressing the “Discovery”[...]

System word definitions in the Discov ery List:  M AC Address: Shows the device MA C Address.  IP Address: Shows the cu rrent IP address of the device.  Protocol version: Shows the versi on of the Utility protocol.  Product Na me: Shows the device product name.  System Nam e: Shows the appointed device system n ame.  Location: Sh [...]

 Gateway: Shows the Gateway set of the device. View Trap: The Trap function can receive the events that happen from the Web Manageme nt Switch in the Monitor List. There is a light indicator behind the “View Trap” but ton, when the light indicates in green, it means that there is no trap transmitted, and else when it indi cates in red, it me[...]

Add Item: To add a device to the Monitor List manually, enter the IP Address of the device that you want to monitor. Delete Item: To delete the device in the Monitor List. Device Setting You can set the device by using the function key in the Device Setting Dialog box. Configuration Setting: In this Configuration Setting, you can set the IP Address[...]

Figure 10. Password Change Firmware Upgrade: When the device has a ne w function, there will be a new firmware to update the device, use thi s function to update. Figure 11. Web Access: Double click th e device in the Monitor List or select a device in the Monitor List and press this “Web Access” button to access the device in Web browser. Tool[...]

21 Monitor Save: To record t he setting of the Monitor List to the default, when you open the We b Management Utility next time, it will auto load the default recorded setting. Monitor Save As: To re cord the setting of the Monitor List in appointed filename and file path. Monitor Load: To manually load the setting file of the Monitor List. Exit: T[...]

how to configure the Switch to enab le its smart functions including:  Port Setting (Speed/Disable, Flow Control and Port Bandwidth Rate Ingress/Egre ss)  VLAN Setting (802.1Q VLAN)  Trunking  Port Mirroring  QoS Setting  PoE Setting  System Setting  Device status and Statistic Login Before you configure this device, note th[...]

Or through the Web M anagement Utility, you do not need to remember the IP Address, sel ect the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser. When the following dialog pag e appears, remain enter the default password "admin" and press Login to ente r the main configuration window. [...]

Setup Menu When the main page appears, find the Setup menu in the left side of the screen (Figure 15). Clic k on the setup item that you want to configure. There are eleven options: Port Settings, VLAN Settings, Trunk Settings, Mirror Settings, QoS Settings, PoE Settings, Device Status, St atistic, System Settings, Trap Setting, Password Settings, [...]

Port Settings In Port Settings menu (Figure 16 ), this page will show each port’s status, press the ID para meter to set each port’s Speed, Flow Control, Rate Control Ingress and Egress . When you need to renew the posted information, pre ss the “Refresh” button. The Link Status in the screen will show the connection speed and duplex mode; [...]

26 Speed/Disable: This setting has six modes— 100M Full , 100M Half , 10M Full , 10M Half, Auto and Disable —for speed o r port disable selections. Flow Contr ol: This setting determines whethe r or not the Switch will be handling flow control. Set FlowCtrl to Enable for avoiding data transfer overflow. Or it set s to Disable ; there is either [...]

VID: select the VID group that you set. When you select VID Table Setting, press “Add new VID” to create new VID group, fro m port 01 ~ port 16, sele ct Untag Port, Tag Port or Not Member for ea ch port. To save the VID group, press “Apply” button. To remove the selected VID group, select the VID group and press “Remove th e VID” button[...]

Trunk Setting The Trunk function enables to cascade two device s with a double times bandwidth (up to 1600Mb ps in full duplex mode). There are 4 selection for the trunk setting, port “09,10”, port “09,10,11,12”, port “09,10,11,12,13,14 ,15,16” or sel ect “disable” for closing this function. Figure 20. Trunk Settings Be sure that th[...]

RX (receive) mode: this mode will duplicate the data that send to the source and forward to the sniffer port. Both (transmit and receiv e) mode: this mode will duplicate both the data transmit from and data that send to the source port, then it will forward to the sniffer port. Figure 21. QoS Setting There are three selections in QoS setting, Disab[...]

Port Based: to set the Switch QoS by port based, select the ports which need to high er the quality by changing Norm al to High. Figure 24. IEEE 802.1p Based: to set the Switch QoS base on IEEE 802.1p, Figure 25. PoE Setting When click on the PoE Setting, the status of the PoE will present on the screen, it will sh ow the PoE Enable, Priority, Powe[...]

Figure 26. Press “Refresh” button to refresh the status of the PoE. Press click on the ID parameter to enter to the selected port to configure the PoE settings, sel ect enable to activate the PoE function from port 1 to port 8, and di sable to deactivate the PoE function. Click “Apply” button to save the setting. Figure 27. Device Status Cl[...]

Statistic The Statistic Menu screen will show the status of each p ort packet count. Figure 28. Statistic For Detail packet information, click on the ID parameter as Figure 29. Figure 29. 32[...]

System Setting The System Setting includes t he Web Server P ort, System name, Location name, Login Timeout, IP Address, Subnet Ma sk and Gateway. Through the Web Man agement Utility, you can easily recognize the device by using the System Name and the Location Name. The Login Timeout is to set the idle time-o ut for security issue, when there is n[...]

Trap Setting The Trap Setting enables the device to monitor the Trap through the Web Manage ment Utility, set the Trap IP Address of the manager where the trap to be sent . Figure 31. Trap Setting  System Ev ents: Monitoring the system’s trap. Device Bootup: a trap when bootin g up the system. Illegal Login: a trap when there is using a wrong [...]

 PoE Events: Monitoring the PoE ports status. PoE Power fail: a trap when the port’s power source is fail or the PD64012 is fail. Power on/Power down: a trap when the PoE po rt’s power is on and down. Power over current: a trap when the PoE port’s power is over current. Power short circuit : a trap when the PoE port’s powe r circuit was [...]

Backup Setting The backup tools help you to backup the current setting of the Switch. Once you need to backup the setting, press the “Backup” button to save the setting. To restore a cur rent setting file to the device, you must specify the backup file and press “Restore” button to proceed the setting of the recorded file. Figure 33. Backup[...]

Logout When press this function, the web configuratio n will go back to first Login page. Figure 35. Logout 37[...]

[...]

39 TECHNICAL SPECIFICATIONS General Standards IEEE 802.3 10BAS E-T Ethernet IEEE 802.3u 100B ASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af comp liant Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex ), 20Mbps (full-duplex ) Fast Ethernet: 100Mbps ( half duplex), 200Mbps (full- duplex) Topology Star Network [...]

40 Physical and Environmental AC inputs 100-240V AC, 50-60 Hz internal univ ersal power supply Power Consumption 9Watts (max. no PD Dev ice connected) 130Watts (max. with 8 x 15.4 w PoE Device conne cted) Temperature Operating: 0 ° ~ 40 ° C, Sto rage: -10 ° ~ 70 ° C Humidity Operating: 10% ~ 9 0%, Storage: 5% ~ 90% Dimensions 440 x 140 x 44 mm [...]