LG Electronics N194WA manual

www .lg.com O WNER’S MANU AL NET W ORK MONIT OR Please read this manual caref ully befor e operating your se t and re tain it f or futur e ref erenc e. NETWORK MONIT OR MODEL N19 4W A ENGLISH[...]

Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . OWNER'S MANUAL /Cards Power Cord (Depending on the country) 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) [...]

1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the powe[...]

2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventila[...]

3 Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. [...]

4 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, th[...]

5 Connecting the Display Disassembling the stand 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 1 . Place the monitor with its front facing downward on a soft cloth. 2. Turn[...]

6 4. Pull out the stand to remove. 5. Pushing the PUSH button, take the stand base from stand body. Good Position Bad Position Warning: You can hurt your finger. Connecting the Display[...]

7 7 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚ to 20˚ Ergonomic It is recommended that in order to maintain an ergonomic [...]

8 8 Connecting to the Computer 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically on D-SUB input. Connecting the Display Wall-outlet type signal input cables A B Connect D-SUB(RGB Analog) Cable (PC) Connect D-SUB(RGB Analog) Cable (Ma[...]

9 9 Wall-outlet type signal input cables Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form to . 1 2 Connect peripheral devices Connect LAN Cable Connecting the Display Keyboard/Mouse Input LAN cable should be connected before boo- ting PC.(This item must be purchased s[...]

10 Connecting the Display T o arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holder. 1. Open the cable holder and fix the cables inside the Cable holder . NOTE This picture shows how to organize cables generally and may look different from your product. Cable holder[...]

11 11 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OS[...]

12 12 Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your displ[...]

13 13 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available ad[...]

BRIGHTNESS CONTRAST GAMMA PICTURE 14 14 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu Supported signals Description : LAN input LAN : D-SUB input D-SUB To adjust the brightness, contrast and gamma of the screen PRESET RED GREEN BLUE [...]

15 15 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU B[...]

16 16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. PICTURE PRESET RED GR[...]

17 17 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to[...]

18 18 On Screen Display(OSD) Selection and Adjustment SETUP MENU : Exit : Adjust : Adjust SET : Select another sub-menu To choose the language in which the control names are displayed. To adjust position of the OSD window on the screen. LANGUAGE OSD POSITION WHITE BALANCE FACTORY RESET If the output of the video card is different from the required [...]

19 19 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description MOVIE INTERNET NORMAL USER INTERNET : For text images (Word processing etc.) MOVIE : For animation images in videos or movies This is under normal operating conditions. This feature lets you easily select the best desired image condition optimized to the environmen[...]

No image appears No image appears 20 20 T roubleshooting Check the following before calling for service. Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display onnected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "OUT OF RANGE" message on the scree[...]

21 21 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the result[...]

22 22 T roubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Pane[...]

23 23 Specifications Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 48.133 cm (18.95 inch) Flat Panel Active matrix-TFT LCD , Anti-Glare coating Visible diagonal size: 48.133 cm 0.2835 mm x 0.2835 mm pixel pitch Horizontal Freq. [...]

24 24 Specifications Preset Modes (Resolution) - D-SUB (Analog) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode Indicator On Mode Sleep Mode Off Mode Blue Flicker Off LED Color MODE 1 2 3 4 *5 31.469 31.468 37.879 48.363 55.935 60 70 60 60 60 640 x 480 720 x 400 800 x 600 1024 x 768 1440 x 900 LAN Preset Modes [...]

Stand Base Head 25 This monitor satisfies the specifications of the Wall mount plate or the interchange device. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 1 . Place the [...]

26 Installing the W all mount plate 4. Pull out the stand to remove. 5. Pushing the PUSH button, take the stand base from stand body. Good Position Bad Position Warning: You can hurt your finger.[...]

27 27 Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.LG recommends that wall mounting be performed by a qualified professional installer. [...]

Make sure to read the Safe t y Precautions befor e using the product . Keep the OWNER’S MANUAL( CD) in an acces sible place f or furture ref erence. The model and serial number of the SET is located on the back or one side of the SET . Rec ord it below should y ou ever need ser vice. MODEL SERIAL With L GE Network Monitor , some PC programs may n[...]