LG 42LY970H manual

EZ-Manager Wizard pages 12 – 21 Custom Master TV Setup pages 37 – 39 Cloning Procedures pages 40 – 45 EXPERIENCED INST ALLER Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. Lodging Guest Interactive Pro:Centric ® TVs © Copyright 2015 LG Electronics U.S.A., Inc. P/N: 206-4260 (Rev C[...]

2 206-4260 © Copyright 2015 LG Electronics U.S.A., Inc. MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ W ARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER[...]

3 206-4260 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accor - dance with the manufacturer ’ s instructions. 8. Do not install near any heat sources, such as rad[...]

4 206-4260 (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below . An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power [...]

5 206-4260 T able of Contents Safety W arnings .................................. 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 T able of Contents ................................. 5 Commercial Mode Overview ..................... 6 – 9 Setup Checklist ................................. 6 Pass-through Mode ....[...]

6 206-4260 Commercial Mode Overview This document describes how to set up L Y970H Pro:Centric  ® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’ s CPU, Protocol T ranslator Card (PTC), or embedded b -LAN™ (EBL) module, or it resides [...]

7 206-4260 Commercial Mode Overview (Cont.) T ypical Installer Menu TV Setup Menus xxL Y970H PTC INST ALLER MENU CPU-CTV 000 INST ALLER SEQ 000 UPN 000-000-000-000 ASIC D279 PTC V1.01.033 CPU V3.02.74.01 Channels Picture Mode Sound Mode Standard Aspect Ratio 16:9 Sleep Timer O Quick Picture Sound General Safety Accessibility QUICK SETTINGS ^ ^ F[...]

8 206-4260 Commercial Mode Overview (Cont.) When the TV CPU is configured with an FTG Channel Map, the CPU controls and restricts the tuning operation of the TV , and when the EBL is configured with an FTG Channel Map, the EBL controls and restricts the tuning operation of the TV . In these models, depending on the types of channels included in the[...]

9 206-4260 Commercial Mode Overview (Cont.) While the TV is in FTG Mode: • Users can still access the Installer Menu using an LG Installer Remote; however , all Installer Menu items will be read-only . • FTG Mode via CPU conguration changes must be made using a TLX le (typically edited in the FTG File Manager), while FTG Mode via EBL con?[...]

10 206-4260 Pro:Centric Operation Pro:Centric Interactive Menu Features LG’s Pro:Centric application enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather , and view hotel and surrounding amenities via custom billboards and points-of-interest maps. Pro:Centric application features[...]

11 206-4260 Pro:Centric Operation (Cont.) Pro:Centric Setup Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide . This document describes only those settings that must be specied on the TVs to enable Pro:Centric remote management and/or the Pro:Centric applica[...]

12 206-4260 Note: After it is turned ON, the TV begins an initialization process, and it may take several minutes for the EZ-Manager Wizard to appear . The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual) of configuring the essential Installer Menu items for Pro:Centric operation. The wizard will ap[...]

13 206-4260 EZ-Manager Wizard (Cont.) Initiate Conguration or Exit the EZ-Manager Wizard The Welcome screen provides a brief introduction to the EZ-Manager Wizard. WELCOME TO LG’S EZ-MANAGER WIZARD EXIT NO PRO:CENTRIC . Use this setup wizard to configure the TV for Pro:Centric and/or Free- T o-Guest (FTG) operation. Select NEXT to continue. .[...]

14 206-4260 EZ-Manager Wizard (Cont.) TV Conguration Options From the TV Conguration Options screen, you can choose how to proceed with the conguration of this TV (assuming you do not opt to exit the wizard, which you may also do at any time). Note: If you intend to use the Zoning feature(s) on the TV for location-specic conguration [...]

15 206-4260 EZ-Manager Wizard (Cont.) EZ-Manager Wizard (Cont.) Note: Zoning features are only applicable for TVs that will be congured using a TLX le (local or remote conguration). ZONES, LABEL, AND ROOM NUMBER NEXT USB CONFIGURA TION . If creating Wi-Fi Zones for AP settings, select the appropriate Wi-Fi Z one # (1-99) based on the Wi-Fi[...]

16 206-4260 EZ-Manager Wizard (Cont.) Congure Pro:Centric Settings Once you select “ NEXT ” from the TV Conguration Options screen, the Searching for Pro:Centric Server screen is displayed. Note: Select the “BACK” button, where available, to check previous settings, as necessary . SEARCHING FOR PRO:CENTRIC SERVER... EXIT It may take 2[...]

17 206-4260 EZ-Manager Wizard (Cont.) (Continued from previous page) If the process is successful, no further user interaction is required, though, in some instances, where the option (for example “NEXT”) is available, you may manually move forward to subsequent steps within the wizard to speed up the process. PROCESSING THE PRO:CENTRIC CONFIGU[...]

18 206-4260 Manual Pro:Centric Conguration 1. With the Searching for Pro:Centric Server screen on display , u se the arrow keys on the Installer Remote to select/highlight MANUAL PRO:CENTRIC at the bottom right of the screen, and then press OK . In the Pro:Centric Manual Conguration screen (see examples below), you will be able to congure [...]

19 206-4260 * PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies. EZ-Manager Wizard (Cont.) (Continued from previous page) 3. Refer to the appropriate subsection below , depending on the Pro:Centric server conguration, to complete the remaining elds. RF Conguration a) In the Media T ype eld, use th[...]

20 206-4260 EZ-Manager Wizard (Cont.) (Continued from previous page) When the Pro:Centric conguration is complete, an EZ-Manager Conguration Complete screen (see example on page 17) is displayed, and after 10 seconds, the wizard exits, and the TV turns OFF . Note: With the EZ-Manager Conguration Complete screen on display , you can also ma[...]

21 206-4260 EZ-Manager Wizard (Cont.) USB Conguration via EZ-Manager Wizard With either the TV Conguration Options or the Zones, Label, and Room Number screen on display , proceed as follows to congure the TV using the USB memory device. 1. Insert the USB memory device that contains the appropriate le(s) into either of the TV’ s USB p[...]

22 206-4260 Ez Download Utility The Ez Download utility , available from the TV Manager / USB Download Menu, enables you to select multiple les at one time from the les loaded on a USB memory device. Y ou may use this utility to download any one or all of the following to a TV : a TLX le for conguration purposes, a TV CPU or PTC softwar[...]

23 206-4260 (Continued from previous page) 3. If the TV is currently in Pass-through Mode, you would like to transfer (T each) a TLX le to the TV via the Ez Download utility , and you intend to use one or both of the TV’s Zoning feature(s), assign the appropriate TV Zone # and/or Wi-Fi Zone # in the TV at this time. See Reference section, “U[...]

24 206-4260 Ez Download Utility (Cont.) (Continued from previous page) CANCEL BACK UPDA TE Channel T uning / Channel Banner Display Logical Physical TV SW Version 03.02. 45 Update Version 03.02.7 4 EZ DO WNLOAD TV MANAGER Select USB Memory Device ˇ USB Device 1: Device Name Logo Image ˇ Splash Image 1920 X 1080 ProC.jpg T each to T V (TLX) ˇ LY9[...]

25 206-4260 Ez Download Utility (Cont.) (Continued from previous page) Note: If a TV Software (CPU) le is selected, TV SW V ersion and Update V ersion elds will be displayed at the bottom right of the screen. Ensure the software version of the selected le is the correct version before applying the update to this TV . 9. If a TLX le that[...]

26 206-4260 xxL Y970H PTC INST ALLER MENU CPU-CTV 000 INST ALLER SEQ 000 UPN 000-000-000-000 ASIC D279 PTC V1.01.033 CPU V3.02.74.01 Installer Menu Use the Installer Menu to set up, change, or view operational settings. This section describes how to access, use, and exit the Installer Menu from the TV itself. However , you should also refer to the [...]

27 206-4260 As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current conguration mode. The table below lists all possible mode identiers for these TV models. Acronym Description CPU-CTV Pass-through Mode with Channel Map in CPU CPU-FTG FTG Mode via CPU CPU-P:C Application T uni[...]

28 206-4260 Installer Menu (Cont.) Installer Menu Items 000 through 070 Item Function V alue Range Default V alue Brief Description of Function 000 INST ALLER SEQ 0 ~ 3 0 Leave default set to 0. 001 POWER MANAGE 0 ~ 7 0 Selects the number of hours of inactivity allowed before the TV automatically turns itself OFF . Set to 0 to disable Power Managem[...]

29 206-4260 Installer Menu Items 071 through 122 Item Function V alue Range Default V alue Brief Description of Function 071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display . 073 CH NOT A VBLE 0 / 1 0 If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL NOT A V AILABLE” message is displayed if user atte[...]

30 206-4260 Installer Menu (Cont.) 000 - INST ALLER SEQUENCE Species entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Energy saving feature. Determines the number of hours, in the range 1 to 7, of inactivity allowed, either at the TV control panel or from the remote, before the TV au[...]

31 206-4260 Installer Menu (Cont.) 007 - STRT VOLUME (Start V olume) This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV will always select that volume level when it is turned ON. The range of values is 0 to 63, 255. If se[...]

32 206-4260 Installer Menu (Cont.) 030 - ACK MASK MPI Communication Parameter . When set to 1, enables ACK feature of MPI. 031 - POLL RA TE MPI Communication Parameter . Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI. 032 - TIMING PULSE MPI Communication Parameter . Sets baud rate for MPI. Step[...]

33 206-4260 071 - BCK. CH-TIME (Channel-Time Display Background Color) See description for item 070 FOR. CH-TIME above. The color chart is the same for both items. 073 - CH NOT A VBLE (Channel Not A vailable) If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL NOT A V AILABLE” message is displayed when a user attempts to direct tune a [...]

34 206-4260 • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP , only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is conne[...]

35 206-4260 104 - ST ART MINOR CHANNEL Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel’s Minor Start Channel number . Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 0 or 255. 106 - ASP RA TIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous as[...]

36 206-4260 Installer Menu (Cont.) Random Distribution of Update T ime: If this item is set to 128 (OFF), the time at which a Data Channel Auto Search (item 1 19 set to 255) and/or an Instant ON update (item 002 set to 2 or 3) occurs is determined as follows: Each TV initiates the search and/ or checks for updates during the 2 AM hour (if the TV cl[...]

37 206-4260 Custom Master TV Setup This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode. The Master TV Setup can used to configure either TVs that are to remain in Pass-through Mode or TVs that are to be configured for FTG Mode via CPU. Cloning requirements and procedures are des[...]

38 206-4260 Custom Master TV Setup (Cont.) Custom Master TV Setup Procedure 1. T urn ON the TV . The next step depends on whether the EZ-Manager Wizard appears on the screen when you turn ON the TV : • If the wizard is displayed , the TV is in the required factory default state. Exit the wizard, and then continue with step 2. • If the wizard is[...]

39 206-4260 Custom Master TV Setup (Cont.) (Continued from previous page) 4. Set up TV features. On-screen setup menus control the features of the TV . Press MENU SETTINGS on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Sound, etc. options to the desired configurations. See “Clonable TV Setup Menu Features” [...]

40 206-4260 Cloning Procedures (Continued on next page) Cloning typically refers to the process of using a Master TV Setup to configure a T arget TV . This section describes how to save (Learn) a Master TV Setup and then transfer (T each) it to a T arget TV using a USB memory device / TLX le. Y ou can also create a TLX le using the FTG File M[...]

41 206-4260 Cloning Procedures (Cont.) (Continued from previous page) 6. Use the Up/Down arrow keys to select Learn From TV (TLX) , and then press OK . CANCEL TV MANAGER USB Download Menu Diagnostics Menu Ez Download Logo Image Download Update TV Software Update PTC Software T each T o TV (TLX) Learn From TV (TLX) 7. In the Learn From TV (TLX) scre[...]

42 206-4260 Cloning Procedures (Cont.) (Continued from previous page) Learning status will be shown in a pop-up progress banner at the bottom of the Learn From TV (TLX) screen. This process may take a few minutes. Do NOT remove the USB device until Learning is complete. When the Learning process is complete, a “Saving completed” message is disp[...]

43 206-4260 (Continued from previous page) • If you would like the T arget TV(s) to remain in Pass-through Mode after T eaching, e nsure the TLX le does not contain an FTG Channel Map; otherwise, T eaching will result in the T arget TV(s) being congured for FTG Mode via CPU. • If the TLX le contains an FTG Channel Map that was Learned [...]

44 206-4260 Cloning Procedures (Cont.) (Continued from previous page) 3. If applicable (see also “Before Y ou Begin” above), make sure to assign the appropriate Zone designation(s) in the T arget TV at this time. Note: In order for the proper location-specic TV Zone and/or Wi-Fi Zone prole data to be applied, the Zone designation(s) must [...]

45 206-4260 Cloning Procedures (Cont.) (Continued from previous page) • If the TLX le includes an FTG Channel Map with RF channels and Aux inputs only , you can choose the format for the channel tuning/banner display . Use the arrows keys to select the desired Channel T uning / Channel Banner Display option—either Logical or Physical—at th[...]

46 206-4260 As indicated in the introduction to this document, there are two separate and distinct methods for configuring L Y970H TVs for FTG Mode of operation: one method is to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL CONFIGURA TION ST ANDPOINT , EACH OF THESE MET[...]

47 206-4260 (Continued from previous page) Note: T o remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/ highlight the item to be removed, and then click the Remove Item button directly above the applicable “List” window . T o clear both the current FTG Configuration List and TV Setup Menu List content[...]

48 206-4260 FTG CONFIGURA TION LIST Data to be saved in FTG Configuration (.tlx) file. FTG File Manager Utilities Overview Note: The data referenced in the FTG Conguration List is only a snap- shot of the current FTG Channel Map and FTG Installer Menu settings when copied to the list. If you make any change(s) to the current data to be included [...]

49 206-4260 FTG File Manager Utilities Overview (Cont.) FTG Channel Map Conguration Utility The FTG Channel Map Configuration Utility enables you to create, view , edit, and print a Logical Channel Map. PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or T ext file. EDIT/ADD MAP Click to o[...]

50 206-4260 FTG File Manager Utilities Overview (Cont.) DELETE Click to remove highlighted channel from FTG Channel Map. ADD After defining a new Logical Channel, click to add channel to the FTG Channel Map. FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. EXIT Click to exit editor a[...]

51 206-4260 FTG File Manager Utilities Overview (Cont.) CONFIGURA TION SETTINGS Select tabs for categories of Installer Menu items to set up TV . FTG Installer Menu Conguration Utility Notes: • The Pro:Centric tab enables you to set up Pro:Centric-specic parameters. The LAN tab enables you to set up a variety of LAN features, including the [...]

52 206-4260 IP Environment Setup The IP Environment Menu enables you to set up the network features of the TV . If you intend to create a Master TV Setup for cloning purposes (see Master TV Setup procedure on pages 37 to 39), all IP Environment settings, with the exception of Wired Network Connection settings, the TV name (editable in the Media Sha[...]

53 206-4260 * PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies. (Continued from previous page) RF Conguration a) Select/highlight the Media T ype eld and press OK on the Installer Remote to display the drop-down list of options. Then, use the Up/Down arrow keys to select RF . Note: If the Media T ype h[...]

54 206-4260 (Continued from previous page) Pro:Centric Application Mode Conguration Select/highlight the Mode eld and and press OK on the Installer Remote to display the drop-down list of options. Then, use the Up/Down arrow keys to select the appropriate Pro:Centric Application Mode setting— Conguration Only , FLASH , GEM , or HTML . If[...]

55 206-4260 IP Environment Setup (Cont.) Conguring a Wired Network Connection Note: If desired, you can congure both wired and wireless connections. However , note that a wired connection is always prioritized over a wireless connection. That is, when the TV is turned OFF and then back ON, if a LAN cable is detected between the TV and the net[...]

56 206-4260 IP Environment Setup (Cont.) (Continued from previous page) If the network is connected successfully , a “Connected to Internet” message will appear just below the progress display . If the network connection is not successful, the progress display will identify the network element in which the connection failed. Check your cabling [...]

57 206-4260 IP Stream Control If necessary , due to an audio and/or video stream delay , IP Stream Control options enable you to compensate for synchronization irregularities by allowing audio PTS and video PTS of fset modications. This menu also enables you to specify the IGMP version (2 or 3). Note that any modications to these settings sho[...]

58 206-4260 IP Environment Setup (Cont.) Media Share Setup Media Share allows you to enable Smart Share ® , Screen Share, DMR, and SoftAP options on this TV . • The LG Smart Share feature allows guests to use the TV to access and view data shared either by wired DLNA Certied ® devices connected to the same LAN as the TV or by wireless LG dev[...]

59 206-4260 IP Environment Setup (Cont.) (Continued from previous page) 3. If desired, you can specify a name for this TV so that it is easy to identify and differentiate from other TVs for which sharing has been/will be enabled. T o edit the TV name (default: TV’s serial number), use the Up/ Down arrow keys to select the TV Name eld, and then[...]

60 206-4260 Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP A V AILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP A V AILABLE to 1). See Installer Menu detailed descriptions for further information. TV Connections Caution: Make these connectio[...]

61 206-4260 Reference: Updating TV/PTC Software using a USB Memory Device This section describes how to update TV (CPU) and/or PTC software using the TV Manager / USB Download Menu “Update TV Software” and/or “Update PTC Software” option(s), respectively , though you may also use the Ez Download utility to update software, if desired. See ?[...]

62 206-4260 (Continued from previous page) 5. In the next screen (Update TV Software or Update PTC Software depending on your selection in step 4): • If more than one USB memory device is currently connected to the TV , be sure to select the USB device that contains the software le you wish to use. If necessary , use the Up/Down arrow keys on [...]

63 206-4260 Reference: Downloading a Splash Screen Image using a USB Memory Device This section describes how to download a splash screen image using the TV Manager / USB Download Menu “Logo Image Download” option , though you may also use the Ez Download utility to download the splash screen image, if desired. See “Ez Download Utility” on [...]

64 206-4260 (Continued from previous page) 5. In the Logo Image Download screen: • If more than one USB memory device is currently connected to the TV , be sure to select the USB device that contains the image le you wish to use. If necessary , use the Up/Down arrow keys on the Installer Remote to select/highlight the Select USB Memory Device [...]

65 206-4260 Reference: Power Consumption Settings The following tables assume that Installer Menu item 1 18 POWER SA VINGS is set to 3 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 255). Note: V alues are results of controlled experiments under laboratory conditions. Item 099 Back Lighting (Static) 42L [...]

66 206-4260 Reference: TV Aux Input Conguration DIRECT ACCESS T uning * TV ENABLE MPI DA T A Installer Menu Item 046 ST ART AUX SRCE (Start Aux Source) V alue Installer Menu MPI DA T A ST A TUS TYPE 0x41 SOURCES ENABLED (R/W) DA T A ST A TUS TYPE 0xD2 CURRENT A V SOURCE (R) D ATA S TAT U S TYPE 0x0D AUX SOURCE (R) Installer Menu Item 029 OLD OCV[...]

67 206-4260 Reference: b -LAN Setup & Overview A b -LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b -LAN module to receive communication from the head end device. At this point, if it [...]

68 206-4260 Reference: FTG Mode via EBL (Local Conguration) The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV (EBL) connection. Refer to the Free-T o-Guest (FTG) Device Configuration Application User Guide for further information. FTG Device Conguration Application software is available online a[...]

69 206-4260 Reference: Auto Input(s) Sensing Feature This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. T o disable auto-sensing for all available Aux inputs, set item 042 to 0. T o enable auto-sensing for all available Aux inputs, set item 042 to 255. For specications on all other available settings (i.[...]

70 206-4260 Reference: Auto Input(s) Sensing Feature (Cont.) Item 042 V alue Inputs Installer Menu Display AV 1 Component HDMI 1 HDMI 2 HDMI 3 001 Enabled Disabled Disabled Disabled Disabled DDDXXDX0 004 Disabled Enabled Disabled Disabled Disabled DDDXX2XD 005 Enabled Enabled Disabled Disabled Disabled DDDXX2X0 032 Disabled Disabled Disabled Disabl[...]

71 206-4260 Reference: RJP Model List & Input Auto-sensing Hierarchy RJP Input Auto-sensing Hierarchy Priority V ideo Audio 1st (Highest) Digital Video In Audio In (3.5mm) 2nd PC Video In Audio In (L/R) 3rd Video In Digital Video In RJP Legacy Models • RJP-101M • RJP-101ML • RJP-1 10F • RJP-1 10FW • RJP-1 10W • RJP-1 10WBR • RJP-1[...]

72 206-4260 Reference: Restoring Factory Defaults on the TV(s) This section describes how to restore all factory defaults or just the Installer Menu factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode. Restore All Factory Defaults This section describes how to restor[...]

73 206-4260 Reference: Using the TV’ s Zoning Features This section describes the TV Zoning and Wi-Fi Zoning features available with the L Y970H model TVs. These features are primarily intended for use when the TV is congured for FTG Mode via CPU operation; however , Wi-Fi Zoning, along with selected elements of TV Zoning (Installer Menu and T[...]

74 206-4260 Reference: Using the TV’ s Zoning Features (Cont.) Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. See also the FTG Channel Map Editor overview on page 50. At the same time, keep in mind that the TV Zone designations are not mutually exclusive. That is, you may opt to place [...]

75 206-4260 Reference: Using the TV’ s Zoning Features (Cont.) Using the Wi-Fi Zoning Feature with Cloning Conguration A location-specic Wi-Fi conguration / TLX le may be saved (Learned) from an individual TV as part of a Master TV Setup and then be used during T eaching. First, the wireless network (i.e., the access point login data)[...]

76 206-4260 Quick Picture Sound General Safety Accessibility GENERAL Language Room Info Time & Date Timers Standby Light On Home/Store Mode SIMPLINK Set ID 1 ^ ^ (Continued from previous page) • Label: Allows you to select a North, South, East, or West text label for this TV . Select/highlight the Label eld and press OK . Then, use the Up/[...]

77 206-4260 Reference: Using Media Share Features When the appropriate Media Share options are enabled in the IP Environment / Media Share Menu (see “Accessing the IP Environment Menu” and “Media Share Setup” on pages 52 and 58, as necessary), guests have the ability to use one or more of the following Media Share features: • Smart Share:[...]

78 206-4260 Reference: Using Media Share Features (Cont.) (Continued from previous page) 3. In the General Menu, use the Up/Down arrows to select Wi-Fi Direct , and then press OK . Note: If Wi-Fi Direct is currently grayed out, you may need to turn OFF another Media Share feature in order to use Wi-Fi Direct. For example, make sure that SoftAP is t[...]

79 206-4260 Reference: Using Media Share Features (Cont.) SoftAP The following steps describe how to access and use the SoftAP feature. 1. T urn ON the TV , and press MENU SETTINGS on the Installer Remote to display the TV menus (either the setup menus or the Function Menu depending on whether the TV is or is not in Pass-through Mode). 2. Use the U[...]

80 206-4260 SPEAKER OUT LINE OUT PTC SERVICE (SERVICE ONL Y) RJP GAME CONTROL / MPI L/MONO A UDIO R COMPONENT IN / A V IN ANTENNA / CABLE IN LAN AUX LAN OPTICAL DIGIT AL AUDIO OUT IN 1 USB IN 1 RESET UPDA TE VIDEO/ Y P B P R PC AUDIO SERVICE TV -LINK CFG Reference: L Y970H Rear and Side Jack Panels COMPONENT IN / A V IN Connect component output or [...]

81 206-4260 Reference: External Stereo Speaker Specications SPEAKER OUT LINE OUT 1 LEFT (T ip) 2 RIGHT (Ring) 3 GROUND (Sleeve) The SPEAKER OUT / LINE OUT 3.5 mm stereo jack on the L Y970H rear panel provides stereo speaker signal outputs (xed speaker , variable speaker , or xed line level [amplier]) for external audio equipment . Set I[...]

82 206-4260 Reference: Installer Remote Control T ypical Key Functions The LG Installer Remote is supplied with and dedicated to operate the TV . The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only . This Installer Remote may vary from the Installer Remote supplied with the TV . DVD/US[...]

83 206-4260 T roubleshooting General T roubleshooting Installation Symptom Possible Cause(s) Possible Solution(s) Cannot direct enter channel number . (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled (recommended setting). If Installer Menu item 028 CH. OVERIDE is set to 0, only channels that are active in t[...]

84 206-4260 T roubleshooting (Cont.) Commercial Mode Check / FTG Operation T roubleshooting TV turned ON? Ye s No Press POWER on Installer Remote. TV is not in Commercial Mode. Call T echnical Support for assistance. TV is in Commercial Mode. No On-screen menu display no longer toggles? Ye s Press MENU SETTINGS repeatedly as if to access the Instal[...]

85 206-4260 Glossary of T erms b -LAN SONIFI Solutions, Inc. proprietary RF communication system used to congure/ control TV via RF distribution system. Channel Lineup Channels set in the TV memory , via Auto T uning/manual editing. Cloning The process of capturing a Master TV Setup and transferring it to a T arget TV using a USB memory device. [...]

86 206-4260 Document Revision History / Open Source Software Notice Open Source Software Notice T o obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referenced license terms, warranty disclaimers and copyright no[...]

206-4260 Revision C © Copyright 2015 LG Electronics U.S.A., Inc. For Customer Support/Service, please call: 1-888-865-3026 www .LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centri c and Smart Share are registered trademarks of LG Electronics Inc. b -LAN is a trademark of SONIFI Solutions, Inc. DLNA Certied [...]