LG N224WHA manual

www .lg.com O WNER’S MANU AL NET W ORK MONIT OR P l ea s e re a d th i s ma n u a l ca r e fu l l y b e for e op e r a t i n g yo u r se t a n d re tain it f or futur e ref erenc e. NETWORK MONIT OR MODEL N22 4WHA ENGLISH[...]

Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . OWNER'S MANUAL /Cards 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) IMPORTANT This accessories may look di[...]

1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the powe[...]

2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventila[...]

3 Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. [...]

4 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, th[...]

5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -6˚ to 17˚ Ergonomic It is recommended that in order to maintain an ergonomic and[...]

6 Connecting the Display -The pivot function allows you to rotate the screen 90 degrees clockwise. 1 . Lift the monitor to its highest height to utilize the Pivot function. 2 . Landscape & Portrait : You can rotate the panel 9 0 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the scree[...]

7 7 7 Connecting to the Computer 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically on D-SUB input. Connecting the Display signal input cables A Connect D-SUB(RGB Analog) Cable (PC) NOTE ‘ Self Image Setting Function’? This functi[...]

8 signal input cables Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form to . 1 2 Connect peripheral devices Connect LAN Cable Connecting the Display Keyboard/Mouse Input LAN cable should be connected before boo- ting PC.(This item must be purchased separately.) Headpho[...]

9 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Using the cable holder 1 2 3[...]

10 Control Panel Functions MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD c[...]

11 Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your display [...]

12 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjus[...]

13 BRIGHTNESS CONTRAST GAMMA PICTURE On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu Supported signals Description : LAN input LAN : D-SUB input D-SUB To adjust the brightness, contrast and gamma of the screen PRESET RED GREEN BLUE COL[...]

14 On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Butt[...]

15 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. PICTURE PRESET RED GREEN[...]

16 MENU : Exit : Decrease : Increase SET : Select another sub-menu On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to re[...]

17 On Screen Display(OSD) Selection and Adjustment SETUP MENU : Exit : Adjust : Adjust SET : Select another sub-menu To choose the language in which the control names are displayed. To adjust position of the OSD window on the screen. LANGUAGE OSD POSITION WHITE BALANCE FACTORY RESET If the output of the video card is different from the required spe[...]

18 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description MOVIE INTERNET NORMAL USER INTERNET : For text images (Word processing etc.) MOVIE : For animation images in videos or movies This is under normal operating conditions. This feature lets you easily select the best desired image condition optimized to the environment ([...]

19 No image appears No image appears T roubleshooting Check the following before calling for service. Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display onnected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "OUT OF RANGE" message on the screen? [...]

20 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results a[...]

21 T roubleshooting Display image is incorrect ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel -[...]

22 Specifications Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight Tilt Range Power Input AC-DC Adapter Environmental Conditions Stand Base Power cord 55.9 cm (21.9 inch) Flat Panel Active matrix-TFT LCD , Anti- Glare coating Visible diagonal size: 55.9 cm 0.282 mm x 0.282 mm pixel pitch Horizontal F[...]

23 Specifications Preset Modes (Resolution) - D-SUB (Analog) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode Indicator On Mode Sleep Mode Off Mode Blue Flicker Off LED Color MODE 1 2 3 4 5 6 *7 31.469 31.468 37.879 48.363 55.935 64.674 65.290 60 70 60 60 60 60 60 640 x 480 720 x 400 800 x 600 1024 x 768 1440 x [...]

24 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. 1 . Place the monitor with its front facing downward on a soft cloth. 2 . Separate the stand after firstly separating 4 screws by using a driver as figure.[...]

25 Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.LG recommends that wall mounting be performed by a qualified professional installer. Ken[...]

M a k e s u r e to r e a d t h e Sa f e t y P re c a u t i o ns befor e using the product . K e e p t h e O W N E R ’ S M A N U A L (C D ) i n a n acces sible place f or furture ref erence. The mod el a nd se ria l nu mbe r of the SET is located on the back o r one s ide of t he SET . Rec ord it below should y ou ever need ser vice. MODEL SERIAL [...]