LG W1943SB-PF manual

M ake sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service. W1943S W1943C User ’ s Guide[...]

A1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the pow[...]

A2 Important Precautions Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures w[...]

A3 Connecting the Display Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Before setting up the monitor, ensure that the power to the monitor, t[...]

A4 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat surface. 3. Change your lock on the product as it follows and turn it in the arrow direction. 2. Place the monitor face down on the cushion or soft cloth. If you can't release the stand base even the locking rib is at a release position, Please push the [...]

A5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~15˚ Ergonomic It is recommended that in order to maintain an ergonomic and c[...]

A6 Connecting the Display OR NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product. Using the Computer 1. Make sure to [...]

Connecting the Display A7 Using the cable holder (This feature is not available in all models.) N E P O 1 2 3 E P ON 4 N O P E Cable holder[...]

A8 Control Function Control Panel Functions MENU Button Use this button to enter or exit from the On Screen Display. Use this button to enter 4:3 IN WIDE , PHOTO EFFECT items, for more information, refer to page A16. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently chang[...]

A9 Control Function Control Panel Functions This Indicator lights up as red when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. Use this button to turn the display on or off. Power Button Power Indicator Use this button to select an icon in the On Screen Display.[...]

A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Scr een Display Control system. A short example is given below to familiarize you with the use of the contr ols. The following section is an outline of the available ad[...]

A11 On Screen Display(OSD) Selection and Adjustment NOTE The order of icons may differ depending on the model (A11~A17 ). The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A Reference To adjust screen color mode PRESET OSD POSITION To adjust the brightness, contrast and gamma of the s[...]

A12 Sub-menus On Screen Display(OSD) Selection and Adjustment NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Y ou were intr oduced to the procedur e of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press [...]

A13 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. To adjust the contrast of the screen. Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. PICTURE PRESET RED[...]

A14 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description CLOCK PHASE SHARPNESS To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of cha[...]

A15 Restore all factory default settings except "LANGUAGE." Press the , buttons to reset immediately. On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be [...]

A16 A16 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description The OSD screen will appear when you touch the button on the right bottom of the monitor. 4:3 IN WIDE To select the image size of the screen. • WIDE: Switch to full screen mode according to input image signal. • 4 : 3: Change the image signal ratio into 4:3. W[...]

A17 On Screen Display(OSD) Selection and Adjustment Icons Menu Name Sub-menu Name Main menu Sub menu Description MOVIE INTERNET NORMAL DEMO USER The OSD screen will appear when you touch the button on the right bottom of the monitor. INTERNET : For text images (Word processing etc.) MOVIE : For animation images in videos or movies This is under nor[...]

A18 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "OUT OF RANGE" message on the screen[...]

A19 A19 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the resu[...]

A20 Display image is incorrect ❁ The screen color is mono or abnormal. ❁ The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. •Make sure the video card is properly inserted in the slot. •Set the color setting higher than 24 bits (true color) at Control Panel -Settings . • Che[...]

A21 Specifications W1943S/W1943C NOTE Information in this document is subject to change without notice. Display Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight Tilt Range Power Input Environmental Conditions Stand Base Power cord 18.5 inches (47.0 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visi[...]

A22 Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 2 3 4 5 6 7 8 *9 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1360 x 768 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60.123 47.712 70 60 75 60 75 75 60 75 60 * Recommend Mode W1943S/W1943C In[...]

Digitally yours[...]