Lynx Series 5000 Rack Frame manual

Series 5000 © LYNX Tech nik AG Brunnenweg 3 64331 Weiterstadt Germ any www.l ynx-techn ik.com Reference Manual R FR 5010 / R FR 5011 Series 5000 Rack Frame CardModul e Ver 2.0[...]

Reference Manual R FR 5010 Versio n1.4 Page 2 Infor matio n in this d ocum ent is subjec t to chan ge wit hout notice. No part of thi s docu ment may be reproduced or tra ns mit te d in an y fo rm o r by any mean s, ele ctr on ic or mechani cal for any purpose, wi thout express written pe rmission of LYNX Techni k AG. LYNX Technik AG may have paten[...]

Reference Manual R FR 5010 Versio n1.4 Page 3 WARNING Electrical supplies in excess of 50 ( fifty) volts peak value are potentially hazardous or lethal. AC supplies b etween 100 and 250 peak volts exist w ithin the rack fr ame chassis when connected to AC pow er. Only qualified personnel should service th e rack frame assembly. Removal of techni ca[...]

Reference Manual R FR 5010 Versio n1.4 Page 4 WARNUNG ! Wenn das Gerät an das Wechselstrom netz angeschlossen ist, treten innerhalb des Gerätes Wechselspannungen zwischen 100 und 250 V auf, di e potentiell gefährlich oder tödlich sein können. Desh alb darf Reparatur und Instandhaltung nur von qualifiziertem Personal durchgeführt werden. Das E[...]

Reference Manual R FR 5010 Versio n1.4 Page 5 This Page is intentionally left blank[...]

Reference Manual R FR 5010 Versio n1.4 Page 6 Warranty LYNX Technik AG warrants that the product will be free fro m defects in materials an d workma nship for a period of two (2) years fro m the dat e of shipm ent. If thi s product pr oves defecti ve during the warranty peri od, LYNX Technik AG at i ts option will either rep air the de fective prod[...]

Reference Manual R FR 5010 Versio n1.4 Page 7 Regulatory information Europe Declar ation of Co nformit y USA FCC 47 Part 15 This device compli es with part 15 of the FCC Rules. Operation i s subject to the following two conditi ons: (1) This device may not cause harmful interfer ence, and (2) this device must acc ept any interf erence rec eived, in[...]

Reference Manual R FR 5010 Versio n1.4 Page 8 Contents Warranty ........... .................... ................... ................. ................ 6 Regulatory information .... .................... ................... ................ 7 Europe .................. ...................................... ................ ............ .......... 7 [...]

Reference Manual R FR 5010 Versio n1.4 Page 9 Electrical Installation. ... ............................................. ............ 31 Install ation In structions . ............................................. ............ 32 Installat ions-Anweisun g ................. .............................. ......... 33 Settings and Control ........ ...[...]

Reference Manual R FR 5010 Versio n1.4 Page 10 Getting Started Packaging The shipping carton and packaging m a terials provide protecti o n for the module during transit. Please retain the ship ping cartons in case subseque nt shipping of the product becomes necessary. Product Description The R FR 5010 / R FR 5011 is a high quality 2 RU high 19 inc[...]

Reference Manual R FR 5010 Versio n1.4 Page 11 board multifunction LED has various s t ates to indicate dif ferent alarm condit ions and a separate GPO alarm output is provid ed for connection to an external monitoring system. The system is co nvection cooled plus forced air- cooling (low noise fans) so it can be u s ed in areas where noise level i[...]

Reference Manual R FR 5010 Versio n1.4 Page 12 Rack Layout Figure 2 and 3 shows explo ded view s of th e R FR 5010 / R FR 5011 . The Front cover is removed and not shown. CardModule Mid Rack Verti cal Supp ort Mou nti ng rails on rear of rack fo r connec ti on pane ls Cauti on : Do not obstruct ve ntialti on hol es on top and bo ttom si des of rack[...]

Reference Manual R FR 5010 Versio n1.4 Page 13 Figure 3 – Exploded r ack view For clarity (to show rack construction) power supplies, rear termination panel and conne ction panels for the modules have been omitted. Caut i on : Do not obstruct ventilation holes on top and bottom si des of rack. Refer to mounting instructions for m ore details. Mid[...]

Reference Manual R FR 5010 Versio n1.4 Page 14 Power Supply The R FR 5010 / R FR 5011 includes the primary power supply. A secon d identical p ower supply can be added for redundancy. The Power su pply is a sophisticate d design designed for critical applications and includes po wer filtering and integral micro processor . This monito rs the supp l[...]

Reference Manual R FR 5010 Versio n1.4 Page 15 Power Supply seen from Front Sec uri n g Scr ew Integral Fan Handle for rem oval LED A l arm indicator Figure 4: Power Suppl y[...]

Reference Manual R FR 5010 Versio n1.4 Page 16 Rear Termination Pan el The R FR 5010/ R FR 5011 ha s an integral termination panel on the rear of the rack for the connection of power and various other connections for expansion and interfacing. Figure 5 Figure 5 R ear Panel Conn ections Rack Connections Power Co nnection There are two pow er connect[...]

Reference Manual R FR 5010 Versio n1.4 Page 17 ! ! A stud is provi d ed on the termination panel for the connectio n of an ext ernal ground . (Figure 5) Note: the chassis is permanently grounde d via the AC connections. Caution Service to be performed by qualified personnel only Caution Please remov e power before attempting to exchange a power fus[...]

Reference Manual R FR 5010 Versio n1.4 Page 18 Alarm Function This function requires the controller option. The user can assig n triggers for the preferre d Major / Minor and No Alarm conditi ons using the co ntroller and supplied sof tware. The alarm connecto r provides GPO co ntacts for 2 alarm levels and a GPI inpu t for future use. This allows [...]

Reference Manual R FR 5010 Versio n1.4 Page 19 Extend Connection Bus Extension . Thi s connect ion is used to inte rface racks together when using the optional LYNX control system. This is a simple (and inexpe nsive) way to extend the reach of the host RCT 5020 controller into several mo re racks fitted with RCT 5010 bus expanders. It uses a propri[...]

Reference Manual R FR 5010 Versio n1.4 Page 20 Control Connectio n An external Control Interf ace is provided on the rear termination panel. When an R CT 5020 Rack Controller (or R CT 5030 Master Controller) is fitted to the rack this port ca n be used for two primary functions: 1. When configured as a RS 232 seri al port thi s can be connected dir[...]

Reference Manual R FR 5010 Versio n1.4 Page 21 LAN Connection This is a standard RJ4 8 connection and i s used to provide stand ard TCP/IP n etwork cont rol connectivity into a contr ol system. To be operational this port requires the R CT 5030 Master Controller is fi tted to the rack. Please see the refe rence manual for the R CT 50 30 for more de[...]

Reference Manual R FR 5010 Versio n1.4 Page 22 Alarm/LED Status Indicators There are a number of status / alarm ind icators visible throu gh the front panel of the R FR 5010 Rack frame. Figure 9. Figure 9. LEDs and i ndicator locations and functi on[...]

Reference Manual R FR 5010 Versio n1.4 Page 23 Power Supply LED Indicators The Table below shows the erro r conditions for the LED on the power supply units. These are visible through the ve ntilation holes on the left si d e of the front of the rack (figure 9) Fan Alar m LED (R FR 5011 only) The Table below shows the erro r conditions for the LED [...]

Reference Manual R FR 5010 Versio n1.4 Page 24 Rack Configuration Assembly If starting with an empty R FR 5010 / R FR 5011 rack frame please follo w the following steps for correct installation of the Series 5000 Card Modules Rack Layo ut Considerations If you have a variety of module types it’s a good idea to plan the order in which you install [...]

Reference Manual R FR 5010 Versio n1.4 Page 25 Redunda nt Power Supply The basic RFR 5010 / R FR 5011 is supplied with the primary powe r supply installed. The redundant supply (option) is installed next to the primary supply. Remote Controller Depending on your system design you m ay hav e one of th e LYNX controller options av ailable (RCT 5010, [...]

Reference Manual R FR 5010 Versio n1.4 Page 26 D AA3320 W IN L IN R OUT L1 OUT R1 OUT L2 OUT R2 OUT L3 OUT L4 OUT R3 OUT R4 DUAL AUDIO ANALOG DIST AMP D AA3320 D IN OUT DUAL ANALOG AUDIO DISTRIBUTION AMP C DA 3000 SDI IN 8 B IT SD I TO A NAL OG CON VERTER LYNX Tec hnik AG nc SDI out 1 G / Y out B / U out R / V out SDI out 2 CVBS out Y (S-v id)out C[...]

Reference Manual R FR 5010 Versio n1.4 Page 27 Hot Swapping Power Supplies The Series 5000 Card Modules and Power Supplies are fully hot swappable in the event of a fault or failure. Power Supply Fa ilure A failure in the Pr imary power suppl y will automa tically trigg er the use of the redundant supply (if fi tted) and wi ll trigger t he followin[...]

Reference Manual R FR 5010 Versio n1.4 Page 28 Rack Installation If you have an empty R FR 5010 rack frame we recommend you assemble the connectio n plates and modules as well as any options such as the redundant power supply and controller before mounting the Rack Fram e into a 19” inch rack. (Please refer to assembly sectio n) Locati on The R F[...]

Reference Manual R FR 5010 Versio n1.4 Page 29 5101 rack frame may (due to the small airf low gap) restri ct the flow of ai r to this piece of equipmen t. Also do not place equi pment or objects on top of the R FR 5010 rack frame th at could restrict airflow from the top of the rack. This may ca use malfunction and damage due to ex cessive heat bui[...]

Reference Manual R FR 5010 Versio n1.4 Page 30 Fig.11: Sub D 9 Connector on Front Cover of R FR 5011 Fig.12: Sub D 9 Connector on right si de of R FR 5011[...]

Reference Manual R FR 5010 Versio n1.4 Page 31 ! ! Electrical Installation. Electrical power is connected to the R FR 5010 / R FR 5011 ch assis via the two I EC power connectors located on the termination panel on the rear of the rack. Th ere is n o power swit ch provided . Two separate and isolated power connections are available, one for the prim[...]

Reference Manual R FR 5010 Versio n1.4 Page 32 Installation Instructions The rack frame chassis R FR 5010 / R FR 5011 is intende d for operation in broadcast environments. The operation in excessive d ust and moisture o r extreme temperature requi res special provisions like • dust filters • air conditioning • avoi dance of conden sed wate r.[...]

Reference Manual R FR 5010 Versio n1.4 Page 33 Installa tions-Anweisung Das Ger ät R FR 501 0 / R FR 5011 ist fü r Anwendungen in Fernsehstudios vorgesehen. Der Einsatz in erhöhter stau biger und feuchter Umg ebung o der außergew öhnlich en Temperaturen erford ert beson dere Maßnahmen wie • Klim atisieru ng • Staubfilter • Verm eiden vo[...]

Reference Manual R FR 5010 Versio n1.4 Page 34 Settings and Control There are no specific setting and control parameters fo r the card rack. This is pro vided via controller o ption (i f fitted) an d the individ ual CardModule assemblies. Please refer to the refe rence ma nuals supplied wi th these ite ms for details on sp ecifi c sett i ngs an d c[...]

Reference Manual R FR 5010 Versio n1.4 Page 35 Specifications (R FR 5010 / R FR 5011) Mechanical Size 2 RU high x 32.5 cm deep including connectors and front cover. 31 cm without front cover. Standard 19” rack mount. Weight (empty) R FR 5010: 4 kg with single power supply R FR 5011: 4,25 kg with single power supply Connections All connections mad[...]

Reference Manual R FR 5010 Versio n1.4 Page 36 Available Options Below is a list of available options for the R FR 50 10 rack frame. Please refer to product brochures or our web site for more detailed inform ation. Model Descripti on R FR 5010 / R FR 5011 Series 5000 Rack Frame (e mpty) with single power supply R PS 5010 Redu ndant p ower supply fo[...]

Reference Manual R FR 5010 Versio n1.4 Page 37 Parts List There are no user serviceable electron ic assemblies within the R FR 501 0 module. The parts list below shows high-l evel sub assemblies used in this rack, which can be ordered separate ly for maintena nce purposes. R FR 5010 Rack Frame (complete ) Description Series 5000 Rack Fram e Model N[...]

Reference Manual R FR 5010 Versio n1.4 Page 38 Contact Information Please contact your local d i stributor; this is your local a nd faste st method f o r ob taining su pport and sales information. Lynx Technik can be cont acted directly using the information below. Address LYNX Tec hnik AG Brunnenweg 3 64331 Weiterst adt German y Website www.lynx-t[...]

Reference Manual R FR 5010 Versio n1.4 Page 39 Notes[...]